USB 802.11b Wireless LAN Adapter
/Flash Disk Doc. No.: 082203-01 REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B This device 802.11b Wireless LAN/Disk (WBD512) and 802.11b Wireless LAN USB Adapter (WUB1600) complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interface, and 2) This device must accept any interface received, including interface that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may ca use harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Warning: Changes or modifications to this unit not expressly approved by the the party responsible for compliance could void the user authority to operate equipment. Tested To Comply With FCC Standards. FOR HOME OR OFFICE USE. CAUTION:
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph 3) This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter The 11Mbps Wireless LAN PCMCIA Card has been tested to the FCC exposure requirements (Specific Absorbtion Rate). U.S. Service Centre:
Company name: Xterasys Corporation Address:4711 CHINO AVE. CHINO,CA91710 USA Contact person: Mr. Larry TEL: 909-590-0600 FAX: 909-590-0388 1) 2)
(d)(2). Table of Contents FCC CERTIFICATION.1 INTRODUCTION1 PARTS NAME AND FUNCTIONS1 LED Indicators..1 Switch (optional)...2 PART 1: 802.11B WIRELESS LAN..1 INSTALLATION.2 INSTALL THE DRIVER & UTILITY...2 In Windows 98SE/ME...2 In Windows 2000...5 In Windows XP.6 INSTALL THE DEVICE.8 In Windows 98SE.8 In Windows ME10 In Windows 2000..11 In Windows XP.12 Verify1 6 NETWORK CONNECTION.17 IN WINDOWS 98SE/ME.17 IN WINDOWS 2000/XP...21 CONFIGURATION2 5 USE MANUFACTURERS CONFIGURATION UTILITY27 Configuration Tool..28 More Setting30 Advanced Setting.36 Information..39 USE WINDOWS XP CONFIGURATION UTILITY.4 0 UNINSTALLATION..4 9 UNINSTALL THE MANUFACTURERS CONFIGURATION UTILITY..49 UNINSTALL THE DEVICE.50 PART 2: USB FLASH DISK..1 INSTALL DRIVER.2 Windows 98/98SE Install from CD RO...2 Windows ME/2000/XP-No Driver is Required.3 REMOVING YOUR USB FLASH DISK...4 MANAGE YOUR USB FLASH DISK..5 MAIN MENU...5 DISK MANAGER.6 DISK PARTITION.6 Switch between Protected and Un-protected Disks8 PASSWORD MANAGER10 Change Password...10 Password Hint11 PC LOCK..11 Plug-in USB Flash Disk11 Plug-in USB Flash Disk and Input Password1 2 To lock a PC..13 To unlock a PC..14 Part 1: 802.11b Wireless LAN Introduction About this manual This document is composed of two parts, which will guide you through the installation procedures for setting up the 802.11b Wireless LAN USB Adapter and the optional USB Flash Disk, respectively. However, if you want to use the optional USB Flash Disk function in Windows ME/2000/XP, no driver installation is required since it is Plug and Play ready. Parts name and functions LED Indicators Link/ACT: Green, on/Blink Power: Green, on 1-1 Part 1: 802.11b Wireless LAN Switch (optional) Switch left to use this device as a Wireless LAN adapter, switch right to use it as a Flash Disk. USB Extension Cable to be used together with USB Adapter. The product must be used with the USB cable and a separation distance of at least 20cm must be maintained between the antenna of this device and users. 1-2 Part 1: 802.11b Wireless LAN USB extension cable 1-3 Part 1: 802.11b Wireless LAN Part 1: 802.11b Wireless LAN 1-1 Part 1: 802.11b Wireless LAN Installation Install the Driver & Utility Note: Always remember to install the Driver & Utility before you plug USB cable into the PCs USB port. In Windows 98SE/ME For Windows 98SE users: As you perform the installation, have your system operating CD-ROM at hand. You may be asked to insert the OS CD-ROM for the system to download a specific driver. 1. Insert the supplied CD-ROM into the CD-ROM drive. Double click on Setup.exe to install the Wireless LAN Driver & Utility. 2. In the Welcome screen, click Next. 1-2 Part 1: 802.11b Wireless LAN 1-3 Part 1: 802.11b Wireless LAN 3. Click Next; Windows will copy all the necessary files to your system. 4. When Windows prompts you to restart your computer, select Yes and click OK. 1-4 Part 1: 802.11b Wireless LAN In Windows 2000 1. In the Welcome screen, click Next. 2. Click Next; Windows will copy all the necessary files to your system. 1-5 Part 1: 802.11b Wireless LAN 3. In the Digital Signature Not Found window, click Yes to continue. 4. Restart your computer. In Windows XP 1. In the Welcome screen, click Next. 1-6 Part 1: 802.11b Wireless LAN 2. Click Next; Windows will copy all the necessary files to your system. 3. Click Continue Anyway to proceed. 1-7 Part 1: 802.11b Wireless LAN Install the Device 1. Plug the square end (Type B) of USB cable into the adapter's USB port. 2. Plug the rectangle end (Type A) of USB cable into the PC's USB port 3. After installing the Wireless USB Adapter, follow below sections to install the adapters hardware. In Windows 98SE 1. Plug USB cable into the PCs USB port. Windows will auto-detect the 802.11b USB Adapter and a New Hardware Found window will show up. 2. Once the Please insert the disk labeled Second Edition then click OK Windows 98 CD-ROM, and window appears, click OK. 1-8 Part 1: 802.11b Wireless LAN 3. Select the correct drive and click OK. 4. Windows will copy all the necessary files to your system. 5. Windows will auto-detect the 802.11b USB Adapter promptly as the icon showed below. 1-9 Part 1: 802.11b Wireless LAN In Windows ME 1. Plug USB cable into the PCs USB port. Windows will auto-detect the 802.11b USB Adapter and a New Hardware Found window will show up. 2. Windows will auto-detect the 802.11b USB Adapter promptly as the icon showed below. 1-10 Part 1: 802.11b Wireless LAN In Windows 2000 1. In Digital Signature Not Found window, click Yes to continue. 2. Windows will auto-detect the 802.11b USB Adapter promptly as the icon showed below. 1-11 Part 1: 802.11b Wireless LAN In Windows XP 1. Plug USB cable into the PCs USB port. Windows will auto-detect the 802.11b USB Adapter and a Found New Hardware Wizard window will show up. Select Install software automatically (recommended). Click Next to continue. the 2. Wait and the Wizard will search for the 802.11b USB Adapter. 1-12 Part 1: 802.11b Wireless LAN 1-13 Part 1: 802.11b Wireless LAN 3. Click Continue Anyway to proceed. 4. Click Next; Windows will copy all the necessary files to your system. 1-14 Part 1: 802.11b Wireless LAN 5. Click Finish to complete the installation. 6. Windows will auto-detect the 802.11b USB Adapter promptly as the icon showed below. 1-15 Part 1: 802.11b Wireless LAN Verify To verify if the device exists in your computer and is enabled, go to Start Settings Control Panel System ( Hardware) Device Manager. Expand the Network adapters category. If the IEEE 802.11b USB Adapter is listed here, it means that your device is properly installed and enabled. 1-16 Part 1: 802.11b Wireless LAN Network Connection Once the driver has been installed, you must make some changes to your network settings. In Windows 98SE/ME 1. Go to Start Settings Control Panel Network. 2. Make sure that you have all the following components installed. Wireless US B Adapter IPX/SPX-compatible Protocol 1-17 Part 1: 802.11b Wireless LAN NetBEUI TCP/IP 3. If any components are missing, click on the Add button to add them in. All the protocols and clients required listed above are provided by Microsoft. 4. component After clicking Add, highlight the you need, click Add. Highlight Microsoft, and then double the item you want to add. Click 5. click on OK. 1-18 Part 1: 802.11b Wireless LAN 6. For making your computer visible on the network, enable the File and Print Sharing. 7. Click the Identification tab. Make up a name that is unique from the other computers' names on the network. Type the name of your workgroup, which should be the same used by all of the other PCs on the network. 1-19 Part 1: 802.11b Wireless LAN 8. Click the Access Control tab. Make sure that Shared-level access control is selected. If connecting to a Netware server, share to User-level access control. level can be set activate the new device. 9. When finished, reboot your computer to 10. Once the computer has restarted and Windows has booted up, a Logon window and require you to enter a will appear username and password. Make up a and click OK. username and password Do not click the Cancel button, or you wont be able to log onto the network. 11. Double-click Neighborhood Network the Windows icon on the 1-20 Part 1: 802.11b Wireless LAN desktop, and you should of the other PCs on the network. see the names In Windows 2000/XP 1. Local
(In Windows 2000) Go to Start Settings Control Panel Network and Dial-up Connections Area Connection Properties.
(In Windows XP) Go to Start Control Panel Network Connections Wireless Network Connection Enabled Wireless USB Adapter Properties. 2. Make sure that you have all the following components installed. Client for Microsoft Networks NWLink NetBIOS 1-21 Part 1: 802.11b Wireless LAN NWLink IPX/SPX/NetBIOS Compatible Protocol Transport Internet Protocol (TCP/IP) Install button If any components are missing, click on the the Client/Service/Protocol required. After selecting the component you need, click Addto add it in. select to 1-22 3. Part 1: 802.11b Wireless LAN 1-23 Part 1: 802.11b Wireless LAN 4. For making your computer visible on the network, make sure you have installed File and Printer Sharing for Microsoft 5. When finished, you must restart your computer to complete installation. Networks. 1-24 Part 1: 802.11b Wireless LAN Configuration refer Note: For Windows XP users, you have an option of using one of two Configuration Utilities. 1) Use Windows XP Configuration Utility.
(the default setting) to Use Windows XP Please Configuration Utility section to use the configuration. 2) Use Manufacturers Configuration Utility If you want to use the Configuration the supplied Utility CD-ROM, you need to disable the Windows XP's wireless configuration. that came with 1. Double-click the network status icon. (see Fig. 1) 2. Click Advanced. (see Fig. 2) 3. Uncheck Use Windows to configure my wireless network settings then click OK. Fig. 1 1-25 Fig. 2 Fig. 3 Part 1: 802.11b Wireless LAN
(see Fig. 3) 1-26 Part 1: 802.11b Wireless LAN Use Manufacturers Configuration Utility and driver After successful installation of the Wireless PC Cards the Configuration Utility icon will appear in the taskbar. You will be able to access the Configuration the Configuration icon. through utility, Utility 1-27 Part 1: 802.11b Wireless LAN Configuration Tool The Configuration Tool Screen displays the current status of the Wireless USB Adapter. Note: Remember to press Refresh to rescan and search for the Access Point. Item SSID Description The SSID is the unique name shared among all points in your wireless network. The name must be identical for all devices and points attempting to connect to the same network. It shows the current SSID setting of the Wireless USB Adapter. Strength Displays the the connection between the Wireless USB Adapter and the Access Point it connects. strength of signal 1-28 Part 1: 802.11b Wireless LAN Description Item Channel Shows the selected channel that is currently in use. (There are 14 channels available, depending on the country.) The infrastructure is intended for the connection between wireless network cards and Access Point. Type Tx Rate Shows the current transfer rate. (Fixed 1 Mbps , Fixed 2 Mbps, Fixed 5.5 Mbps, Fixed 11Mbps or Auto) WEP WEP is a data privacy mechanism based on a 64-bit/128-bit shared key algorithm. Under the drop-down box, you can choose to have WEP encryption Disabled, 64 Bit, or 128 Bit. Link Status Tx Frame Displays the information about the status of the communication (the BSSID of the Access Point is associated). to which the card for which The quantities network card transmit.
(Frame: The unit of packet) the wireless Rx Frame The quantities network card receive. for which the wireless
(Frame: The unit of packet) 1-29 Part 1: 802.11b Wireless LAN More Setting The More Setting Screen displays the available settings of Access Point according to wireless network card including General Connection Setting, Encryption Setting, Profile Setting and Other Settings. 1-30 Part 1: 802.11b Wireless LAN I. General Connection Setting Item Description The Ch annel will change automatically according to AP. You may change the setting of SSID by choosing Any. You may change the settings of TxRate and Network Type. Channel Any Change or Apply II. Encryption Setting Choose Enable WEP , and then you may press WEP More to proceed with the following screen. 1-31 Part 1: 802.11b Wireless LAN Note: You may press Change/Apply to change the settings. Item Description can choose Default Key ID Encryption WEP is a data privacy mechanism based on a 64-bit/128-bit shared key algorithm. Under the drop-down box, you to have WEP encryption Disabled, 64 Bit, or 128 Bit. You can specify up to 4 different keys to decrypt wireless data. Select the Default key setting from the drop-down menu. Note: You must use the same Default Key and Default Key settings for the both sides of the wireless network to connect to). This setting is the configuration key used in accessing the wireless network Key #1/Key
#2/
1-32 Part 1: 802.11b Wireless LAN
#2/
Key #3/Key
#4 via WEP encryption. A key of 10 hexadecimal characters
(0-9, A-F) is required if a 64-bit Key Length was selected. A key of 26 hexadecimal characters (0-9, A-F) is required if a 128-bit Key Length was selected. III. Profile Setting 1. Write current setting to profile:
You may add one new item in "Profile name", and then press "Write current setting to profile" to record the status of connected AP.
(see Figure 1 & 2) Fig. 1 Fig. 2 1-33 Part 1: 802.11b Wireless LAN 2. Load profile setting :
You may select the added item in "Profile name", and then press "Load profile setting". The original setting status of AP can be restored. Fig. 1 Fig. 2 1-34 Part 1: 802.11b Wireless LAN 3. Load factory default setting :
Once you press "Load factory default setting", this Adapter will research for the original default of wireless network card; if you can not find out AP under the channel of default, the wireless network card will choose the AP within other channels to operate. 1-35 Part 1: 802.11b Wireless LAN Advanced Setting The Advanced Setting Screen shows you to change advanced configuration, such as Power Saving Mode, Fragmentation Threshold, and RTS/CTS Threshold. 1-36 Part 1: 802.11b Wireless LAN Note: Once you choose the Enable auto power saving" item, the system will auto-detect the levels of power saving; if not, you will need to choose the levels manually. Item Description Power Saving Mode Displays the power saving levels (Level 0 ~ Level 4) 1-37 Part 1: 802.11b Wireless LAN Item Description Fragmentation Threshold To fragment MSDU or MMPDU into small sizes of frames for increasing the reliability of frame (The maximum value of 2346 means no fragmentation is The performance will be decreased as well, thus is recommended. transmission. environment needed) noisy a RTS/CTS Threshold This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. 1-38 Part 1: 802.11b Wireless LAN Information Click Information Tab to view basic information about the Utility like the Driver, Firmware and ZDConfig Version. Press the OK button to exit the application. 1-39 Part 1: 802.11b Wireless LAN Use Windows XP Configuration Utility 1. Go to Start Control Panel Network and Internet Connections Network Connections. In Network Connections window, the Wireless Network right-click Connection Enabled Wireless USB Adapter icon, and select Properties. 2. 3. In Wireless Network Connection Properties window, select the General tab. Click Configure to enable Windows configuration. 1-40 Part 1: 802.11b Wireless LAN Property Description Authentication Mode The authentication mode defines configuration options for the sharing of wireless networks to verify identity and access privileges of roaming wireless network cards. You may choose between Open System, Shared Key, and Auto. Open System: If the Access Point is System"
using
"Open 1-41 Part 1: 802.11b Wireless LAN then authentication, the wireless adapter will need to be set to the same authentication type. Shared Key: Shared Key is when both the sender and the recipient share a secret key. Auto: Select Auto for the USB adapter to select the Authentication type automatically depending on the Access Point Authentication type. Shows the selected channel that is currently used. To fragment MSDU or MMPDU into small sizes of frames for increasing the reliability of frame
(The maximum value of 2346 means no needed) transmission. The performance will be decreased as well, thus a noisy environment is recommended. fragmentation is Channel Fragmentation Threshold Power Save Level Network Type It displays the current network type, which can be divided into two types:
j Ad-Hoc k Infrastructure It shows the levels of Power Save, which can be divided into five levels:
j Level 0 (Save less power) k Level 1 l Level 2 m Level 3 n Level 4 (Save more power) Enable the function to allow the Adapter to go to sleep mode, during which data communication could be interrupted. (Disabled or Enabled) Power Save Mode 1-42 Part 1: 802.11b Wireless LAN RTS/CTS Threshold SSID Transmit Data Rate WEP Encryption This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. The SSID is the unique name shared among all points in your wireless network. The name must be identical for all devices and points attempting to connect to the same network. It shows the current transfer rate. (1, 2, 5.5, or 11Mbps or Auto) WEP is a data privacy mechanism based on a 64-bit/128-bit shared key algorithm. Under the drop-down box, you can choose to have WEP encryption Disabled, 64 Bit, or 128 Bit. 4. In Wireless Network Connection Properties window, select the Wireless Networks tab. 1-43 Part 1: 802.11b Wireless LAN Use Windows to configure Check the box to enable Windows configuration.
* Use Windows to configure Note: Once you enable windows configuration, you use Windows XPs Wireless Configuration Utility to configure the wireless settings. can
* Use Manufacturers Configuration Utility If you want Note:
to use Manufacturers Configuration Utility to configure the wireless settings, make sure the check box is not checked 1-44 Part 1: 802.11b Wireless LAN then click the Network Status icon in the taskbar.
(Please refer to below figure) Available networks Displays all available networks. Configure Click the button to set up a new network or WEP configuration as illustrated as below. 1-45 Part 1: 802.11b Wireless LAN Refresh Click the button to refresh and search for all available networks. Preferred networks From available network(s) listed above, you can select preferred one(s) in an order that you can arrange. The marked one is the currently used network. Move up 1-46 Part 1: 802.11b Wireless LAN Move the selected network forward one position. Move down Move the selected network back one position Add Click the button and the Wireless Network Properties window will appear. In the Network name field, enter your desired network name listed in the above Available networks box, and click OK. Note: The new settings will be active only after you click on OK in the Wireless Network Connection Properties window. Remove Highlight the unwanted network listed in the Preferred networks box, and click the button to remove it. Properties Highlight the network listed in the above Preferred networks box, and click the button to display its properties. 1-47 Part 1: 802.11b Wireless LAN Once network configuration is done, make sure to click OK. The new parameters will be saved and active only after doing so. 1-48 Part 1: 802.11b Wireless LAN Uninstallation In case you need the Manufacturers Configuration Utility or the Driver, please refer to below section. to uninstall Uninstall the Manufacturers Configuration Utility 1. Go to Start Programs Wireless LAN USB Uninstall. 2. Click OK to continue. 1-49 Part 1: 802.11b Wireless LAN 3. Select Yes, I want to start my computer now. Click Finish to complete the uninstalled procedure. Uninstall the device 1. Right-click My Computer Properties Hardware Device Manager. 2. Right-click Wireless USB Adapter then click Uninstall (or Remove). 1-50 Part 1: 802.11b Wireless LAN 3. Click OK to uninstall the device. 4. The system may prompt you to restart your computer. Click Yes. Its okay now to uninstall from your computer. the device 1-51 Part 2: USB Flash disk Part 2: USB Flash Disk 2-1 Part 2: USB Flash disk Install Driver Windows 98/98SE Install from CD ROM In Windows 98/98SE, you will need to install the driver found on the CD that comes with this device. Run Flash Driver.exe.. Follow the on-screen instructions to proceed. 2-2 Part 2: USB Flash disk Click Finish to complete the installation. After the installing process is finished, remove the cap from your USB Flash Dish and plug the USB connector to the USB port computer. Then, open My on your Computer and you will see a newly added icon; shown on the screen as a removable disk drive. Windows ME/2000/XP-No Driver is Required This device is Plug and Play compliant, therefore, once you plug it into your Windows based system, your system will automatically detect it as a removable hard disk. You can go to My Computer to check if there is a newly added icon. If yes, it is ready for use. If not, you may have to check if the USB Flash Disk is connected properly to your USB port. 2-3 Part 2: USB Flash disk Removing your USB Flash Disk Warning: Each time you remove the USB Flash Disk from your computer, be sure to use the Unplug/Eject icon to avoid data loss or damage to your Flash Disk. on the taskbar 2-4 Part 2: USB Flash disk Manage your USB Flash Disk Main Menu Step 1.Load the included CD and open it. Double-click MYKEY. Step 2.An USB Flash Disk icon will appear on your desktop
, a Star icon will also appear on the bottom right corner of the task bar on your screen. Step 3.Right-click the icon. Step 4.Click Option. The USB Flash Disk Utility will appear. 2-5 Part 2: USB Flash disk Step 5.The USB Flash Disk Utility consists of four tabs for management. See the following for details as how to use and manage this device. Disk Manager Disk Manager is readable only. On this box, you will know the used/free capacity of your flash disk. Disk Partition In this box, you can divide the USB Flash Disk into two partitions:
Un-protected Disk Space: all data located here is accessible to anyone who uses your computer or Flash Disk. When logging out 2-6 Part 2: USB Flash disk of the protected area you are automatically redirected to the Un-protected Disk area. Protected Disk Space: this area is password protected. Step 1.Drag the pointer to adjust the capacity of the Protected/Un-protected disk. Step 2.Press A warning message appears to advise that all Create Partition. data on the disk will be erased. You can cancel this action by clicking Cancel. Or click OK to continue. 2-7 Part 2: USB Flash disk Step 3. Click Cancel to copy your data to a Hard Disk before creating your prtition. Click OK to create your partition. Any and all Data stored on your Flash Disk will be destroyed. Switch between Protected and Un-protected Disks Enter the Protected Disk Step 1. Right click
. Select Login
. Step 2. You are prompted to enter your password. The default password is 0000. It is suggested that you set your own password. If you forget your password, press uto get see your password hint. 2-8 Part 2: USB Flash disk Once you enter the protected disk, the disk icon shown in My Computer will change from to
, and vise versa. Enter the Un-protected Disk Step 1.Right click
. Select Logout to enter the Un-protected Disk. 2-9 Part 2: USB Flash disk Password Manager Password can be changed in this box. You can also set a password hint for use if you forget your password. Default password is set to: 0000 Change Password Step 1. Enter the Old Password, the default is 0000. Step 2. Enter the New Password.
(Maximum 4 characters long use letters or numbers) Step 3. Confirm password by re-entering the new password. 2-10 Part 2: USB Flash disk Step 4. Enter a hint of your own; this will be helpful to remind you if you forget your password. Step 5. Press Step 6. Password Change to continue. has been changed message appears. Click OK. Password Hint
You can leave the Password Hint blank if you dont want to use it. PC LOCK Once PC-Lock is enabled, the PC you are presently using is locked. To unlock this PC, you can only use this USB Flash Disk. To enable PC Lock, there are two conditions for your choice, Plug-in USB Flash Disk This means that you have to plug this USB Flash Disk into your computers USB port in order to open your PC;
2-11 Part 2: USB Flash disk Plug-in USB Flash Disk and Input Password This means to open the PC, you are required not only to plug the USB Flash Disk, but also have to enter your password. 2-12 Part 2: USB Flash disk To lock a PC 1. Right click
. 2. Select Option PC-Lock Setting. 3. Check Enable PC-Lock. 4. Select the Unlock Condition that fits your needs. 5. Press 6. Press Exit. Change. 7. Return to your desktop and right click again. 8. Move the cursor to PC Lock You PC is now locked. 9. If this function is enabled, your PC will not respond unless this USB Flash Disk is plugged in. 2-13 Part 2: USB Flash disk To unlock a PC 1. Plug the USB Flash Disk into the locked 2. PC. If the unlock condition is set to Plug-in USB Flash Disk and Input Password, a password box will pop up. 3. Enter your password. The PC is now unlocked. 2-14