FCC ID: HED-MLTGCNLR 60GHz Long Haul terminal

Quick Start Guide 60GHz Long Haul Terminal MLTG-CN-LR Package Contents 1 2 3 4 5 6 1. 60GHz Access Point MLTG-CN-LR 2. 1 x 24 W passive PoE injector 3. 1 x Power cord 4. 1 x DC connector plug 5. 3 x Cable glands 6. Documentation QR-code card Overview Scope mount 1. 2. Alignment/Signal Strength LED Indicators 3. System LED Indicators:

60G: On (60GHz wireless link), Blinking (activity). 2.5G: On (link), Blinking (activity) SFP: On (Uplink port link), Blinking (activity) PWR: Slow blink during system boot up. 4. Reset button 5. Grounding Screw 6. DC IN Port 7. 8. LAN Port SFP Port 1 4 2 3 5 6 7 8 Interface LAN Port SFP Port 60 GHz MAC Address Ethernet MAC

(Printed on the devices label) Ethernet MAC + 1 Ethernet MAC + 2 www.edge-core.com 1 E112021-MR-R01 Installation Quick Start Guide Warning: For a safe and reliable installation, use only the accessories and screws provided with the device. Use of other accessories and screws could result in damage to the unit. Any damages incurred by using unapproved accessories are not covered by the warranty. Avertissement: Pour une installation sre et fiable, utilisez uniquement les accessoires et les vis fournies avec lappareil. Lutilisation dautres accessoires et vis pourrait endommager lappareil. Les dommages causs par lutilisation daccessoires non approuvs ne sont pas couverts par la garantie. 1 Ground the MLTG-CN-LR Ground the MLTG-CN-LR by connecting a ground wire to the grounding point on the device and to nearby good earth. 2 Make Network Connections SFP Port 1. Install a 1000BASE-T fiber transceiver in the Uplink SFP port and then connect outdoor-rated fiber cable to the transceiver port. The following list of Edgecore transceivers are supported:

ET4202-SX ET4202-LX ET4202-EX ET4202-ZX Mount the MLTG-CN-LR 3 Two optional precision bracketsICC-BRACKET-LR and ICC-BRACKET-

LCare designed for wall and pole mounting and provide additional degrees of movement for antenna alignment. a. Using the LR Precision Bracket RJ-45 Port 1. Connect outdoor-rated Category 5e or better cable to the 2. 1000BASE-T RJ-45 port. Be sure to use the included weatherproof RJ-45 port cover.

(Optional) Connect a local LAN switch or computer to the LAN 1000BASE-T RJ-45 port. Be sure to use the included weatherproof RJ-45 port cover. Note: The LAN port connection provides PoE power to the unit. 2 Quick Start Guide 1. Attach the two main sections of precision bracket using two M8 25 mm bolts, flat washers, and spring-lock washers. 2. Use the M8 40 mm bolt with flat and spring-lock washers to attach tightened. The bracket is shipped with the nut in a loose position. 6. Before aiming, ensure the horizontal adjustment bolt and nut is the bracket to the vertical-adjustment mechanism. 3. 4. Seat the four M8 125 mm bolts in the main assembly so that the bolt heads are held in the assembly grooves and are unable to turn. Place the pole-attachment bracket over the bolts and secure them with four M8 lock nuts. (The pole attachment bracket needs to be removed and re-attached when mounting on a pole) 7. Install the LR Precision Bracket onto the MLTG-CN-LR using four M8 15 mm bolts, spring-lock washers, and flat washers. 5. Ensure all four position-locking bolts on the LR Precision Bracket are tight before installing. 3 4 1 2 B A Note: Do not adjust bolts A and B without first loosening 1, 2, 3, and 4 respectively. Note: It is recommended to only adjust one axis (A for vertical or B for horizontal) at a time. 8. Use a general visual estimate or the optical scope for initial 9. alignment before starting on other adjustments. Loosen the horizontal adjustment bolts 3 and 4. Use fine-tune bolt B to optimize the horizontal position. Re-tighten bolts 3 and 4. 10. Loosen the vertical adjustment bolts 1 and 2. Use fine-tune bolt A to optimize the vertical position. Re-tighten bolts 1 and 2. 11. Repeat steps 9 and 10 until the alignment position is optimized. 12. Ensure all bolts are fully tightened and remove the alignment scope (if installed). 3 b. Using the LC Precision Bracket Quick Start Guide 2 3 A B 1 4 Note: Do not adjust bolts A and B without first loosening 1, 2, 3, and 4 respectively. Note: It is recommended to only adjust one axis (A for vertical or B for horizontal) at a time. 4. Use a general visual estimate or the optical scope for initial 5. 6. alignment before starting on other adjustments. Loosen the horizontal adjustment bolts 3 and 4. Use fine-tune bolt B to optimize the horizontal position. Re-tighten bolts 3 and 4. Loosen the vertical adjustment bolts 1 and 2. Use fine-tune bolt A to optimize the vertical position. Re-tighten bolts 1 and 2. 7. Repeat steps 5 and 6 until the alignment position is optimized. 8. Ensure all bolts are fully tightened and remove the alignment scope (if installed). 4 Use an Alignment Scope Using the ICC-SCOPE-9x50 Alignment Scope (ordered separately) is strongly recommended for alignment. To install, place the scope on top of the MLTG-CN-LR housing and secure it with its thumb screw. 1. Thread the included steel hose clamps through the eyelets on the back of the LC Precision Bracket and then lightly fasten them around the pole. Both hose clamps must be used for pole mounting. 2. Align the MLTG-CN-LR antenna with a Distribution Node before tightening the clamps securely. 3. Install the LC Precision Bracket onto the MLTG-CN-LR using the included four M8 10 mm bolts. 4 Quick Start Guide Access the Web User Interface 7 a. Using the LAN Port 1. Connect a PC directly to the MLTG-CN-LRs LAN port. 2. Set the PC IP address to be on the same subnet as the MLTG-CN-

LR LAN port default IP address. The PC address must start 192.168.2.x with subnet mask 255.255.255.0). Enter the MLTG-CN-LRs default IP address of 192.168.2.1 into the web browser address bar. Log in to the web interface using default settings:

Username = admin Password = admin 3. 4. The MLTG-CN-LR can also accommodate a Picatinny Rail and corresponding widely available laser sights. 5 Connect Power a. DC Power Wire the included DC terminal plug to a 24-48 VDC, 0.5-1 A source to provide power to the MLTG-CN-LR. b. Passive PoE Injector Connect the other end of the outdoor-rated Ethernet cable from the Uplink (PoE) port to the PoE injector (passive) supplied in the package. 6 Verify Power is On Check the LEDs The PWR LED should blink slowly during boot-up and be on or blinking when operating normally. 5 Safety and Regulatory Information the limits for a 15 of the FCC Rules. These limits FCC Class B This equipment has been tested and found to comply with Class B digital device, pursuant to Part are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

guarantee that interference will Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. the FCC Rules. Operation is subject This device is not to be operated listed on FCC CFR 15.255 (b). on aircraft except for the conditions IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This operated with minimum distance 193 cm between the radiator and your body. equipment should be installed and IC Statement transmitter(s)/receiver(s) that comply This device contains licence-exempt with Innovation, Science and Economic Development Canadas licence-

exempt RSS(s). Operation is subject conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. to the following two rcepteurs exempts de licence qui de licence d'Innovation, Sciences Cet appareil contient des metteurs /

sont conformes au (x) RSS (s) exempts et Dveloppement conomique Canada. L'opration est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas provoquer d'interfrences. (2) Cet appareil doit accepter toute interfrence, y compris les interfrences susceptibles indsirable de l'appareil. de provoquer un fonctionnement IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 22 cm between the radiator and your body. This device is not to be operated listed on ISED RSS-210 Annex J.1. on aircraft except for the conditions Quick Start Guide Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 22 cm de distance entre la source de rayonnement et votre corps. CE Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. All operational modes:

60 GHz: 802.11ad, 802.11ay The frequency and maximum transmitted power limit in EU are listed as below:

57-66 GHz: 40 dBm AT DE FR LI NO SK BE DK HR LT PL TR EE HU LU PT UK BG CH CY CZ EL IE LV RO ES IS MT SE FI IT NL SI The abbreviations of the countries, as prescribed in above table, where any restrictions on putting into service or any requirements for authorization of use exist. CE Mark Declaration of Conformance for EMI and Safety (EEC) This information technology equipment is in compliance with the Directive 2014/53/EU and Directive 2014/35/EU. The Declaration of Conformity (DoC) can be obtained from www.edge-core.com -> support -> download. Japan VCCI Statement Warnings and Cautionary Messages Warning: This product does not contain any serviceable user parts. Warning: Installation and removal of the unit must be carried out by qualified personnel only. Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards. Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment. Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards. 6

Quick Start Guide IC

RJ-45 RJ-45 FCC BSMI (Taiwan) BSMI Taiwan

7 Quick Start Guide Hardware Specifications AP Chassis Size (WxDxH) 355 x 355 x 315 mm (13.98 x 13.98 x 12.40 in) Weight 3 kg (6.61 lb) Temperature Operating: -40 C to 60 C (-40 F to 140 F) Storage: -40 C to 70 C (-40 F to 158 F) Humidity Operating: 5% to 95% (non-condensing) Network Interfaces Ports 2.5G Ethernet Port (PoE IN) SFP Port 60 GHz 802.11ay Power Supply PoE Input Power 48 VDC (non-standard) Power Consumption 15.9 W max. Regulatory Compliances Radio Emissions Safety EN 302 567 V2.1.1 EN 62311 (MPE) 47 CFR FCC Part 15.255 RSS-210 RSS-102 Issue 5 (MPE) MIC Article 2 Paragraph 1 Item 194-2 EN 301 489-1 V2.1.1 EN 301 489-17 V3.1.1 Part 15 subpart B Class B (ANSI C63.4-2014) ICES-003 VCCI-CISPR 32 EN 62368-1: 2014+ A11: 2017 IEC 60950-1: 2005, AMD1: 2009, AMD2: 2013 IEC 60950-22: 2016 IEC 60529-1: 1989+ AMD1: 1999+ AMD2:

2013CSV (IP55) BSMI, CNS 14336-1 Taiwan RoHS CNS 15663 8

40x15mm |

(Adhesive Location) FCC ID: HED-MLTGCNLR IC: 3857A-MLTGCNLR This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynotcause = ---------- --- ---------------------------------

harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3(B) / NMB-3(B) 246000003288A RBO Made in XXXXX Model: MLTG-CN LR Input Voltage Range: 24V~56V meee IR] XXX-XXXXXX T

Accton Technology Corp No. 1, Creation Rd. III, Science-based Industrial Park Hsin Chu 30077, Taiwan R.O.C. Confidential Letter Date: 2022/1/28 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC IDHED-MLTGCNLR To Whom It May Concern:

Long Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby respectfully request confidential treatment of information accompanying this application as outlined below:

Block Diagrams Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We understand that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Respectfully, Applicants company name

: Accton Technology Corp Applicants company address

R.O.C. No. 1, Creation Rd. III, Science-based Industrial Park Hsin Chu 30077, Taiwan Signature

Name and Job Title

: Abby Wei / Manager E-Mail Tel Fax

: mike_peng@accton.com

: 886-3-577-0270 #3780

: 886-3-578-7550

Accton Technology Corp No. 1, Creation Rd. III, Science-based Industrial Park Hsin Chu 30077, Taiwan R.O.C. Power of Attorney Date: 2022/1/28 Dear Sir, I hereby have entrusted the following person to be a proxy regarding application for Type Certification. Sporton International Inc. Hsinchu Laboratory Address

: No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. Name

Leo Huang Job Title

: Manager e-mail

Leohuang@sporton.com.tw I am therefore responsible for the contents of the application. FCC ID: HED-MLTGCNLR Respectfully, Applicants company name

: Accton Technology Corp Applicants company address

R.O.C. No. 1, Creation Rd. III, Science-based Industrial Park Hsin Chu 30077, Taiwan Signature

Name and Job Title

: Abby Wei / Manager E-Mail Tel Fax

: mike_peng@accton.com

: 886-3-577-0270 #3780

: 886-3-578-7550

Accton Technology Corp No. 1, Creation Rd. III, Science-based Industrial Park Hsin Chu 30077, Taiwan R.O.C. Professional Installation Declaration Date: 2022/1/28 FCC IDHED-MLTGCNLR To Whom It May Concern:

Please be advised that due to the unique Market and function targeted by this product, this product will need special trained professional in configuring and installing the product. We hereby declare that the product will be distributed through controlled distribution channel which has special trained professional to install this product and will not be sold directly to the general public through retail store. Respectfully, Applicants company name

: Accton Technology Corp Applicants company address

R.O.C. No. 1, Creation Rd. III, Science-based Industrial Park Hsin Chu 30077, Taiwan Signature

Name and Job Title

: Abby Wei / Manager E-Mail Tel Fax

: mike_peng@accton.com

: 886-3-577-0270 #3780

: 886-3-578-7550

Accton Technology Corp No. 1, Creation Rd. III, Science-based Industrial Park Hsin Chu 30077, Taiwan R.O.C. SDoC Attestation Letter Date: 2022/1/28 We Accton Technology Corp, as the grantee of this project (FCC ID: HED-MLTGCNLR / Brand Name: Edgecore / Model No.: MLTG-CN LR), would like to declare that the composite portion has been authorized under the Supplier's Declaration of Conformity procedures (Sporton report No.: FD1O2206, FCC designation number: TW1131). The final product shall consequently comply with the FCC rule applied for SDoC Procedure. Respectfully, Applicants company name

: Accton Technology Corp Applicants company address

R.O.C. No. 1, Creation Rd. III, Science-based Industrial Park Hsin Chu 30077, Taiwan Signature

Name and Job Title

: Abby Wei / Manager E-Mail Tel Fax

: mike_peng@accton.com

: 886-3-577-0270 #3780

: 886-3-578-7550