Quick Start Guide 802.11ac Wave 2 Dual-Band Enterprise Access Point OAP100e Package Contents 1 2 3 4 5 6 7 8 9 1. OAP100e access point 2. Mounting kit2 brackets and 2 steel hose clamps 3.
(Optional) Mounting bracket 4. DC Terminal plug 5. 2 x Cable glands 6. 2 x Port covers 7. 2 x External 5G omni antennas 8. Console cableRJ-45 to DB-9 9. QR code card Overview 2 3 4 5 6 6 1 1. Grounding point 2. Console port 3. LAN (PoE Out) port: 1Gbps connection to LAN devices 4. Uplink (PoE In) port: 1Gbps uplink connection with 802.3at PoE support 5. DC In port: 24 Vdc 6. 5G Antenna connector 1 3 1 2 4 1 1 1 3 1 1. Mounting points Enclosure for optional module 2. 3. LEDs:
Power: On red (power OK) System: On green (power OK), Blinking (boot up) Uplink: On amber (1Gbps link), On green (10/100Mps link), Blinking (traffic) LAN: On amber (1Gbps link), On green (10/100Mps link), Blinking (traffic) LTE: function not supported 2.4G: On blue (radio on), Blinking (traffic) 5G: On blue (radio on), Blinking (traffic) 4. Reset button www.edge-core.com 1 E042022-MR-R01 Warning: For a safe and reliable installation, use only the accessories and screws provided with the device. Use of other accessories and screws could result in damage to the unit. Any damages incurred by using unapproved accessories are not covered by the warranty. Avertissement: Pour une installation sre et fiable, utilisez uniquement les accessoires et les vis fournies avec lappareil. Lutilisation dautres accessoires et vis pourrait endommager lappareil. Les dommages causs par lutilisation daccessoires non approuvs ne sont pas couverts par la garantie. Note: The drawings in this document are for illustration only and may not match your particular model. Mount the AP 1 The included mounting brackets are designed for pole mounting and provide additional degrees of movement for antenna alignment. a. Using a Single Bracket (Parallel) Installation
. Quick Start Guide 2 3 2. 3. Install the bracket onto the AP using the included four screws. Thread the included steel hose clamps through the eyelets on the back of the Mounting Bracket and then lightly fasten them around the pole. Both hose clamps must be used for pole mounting. c. (Optional) Using Two Brackets (Perpendicular) 1 2 1. 2. Install the bracket onto the AP using the included four screws. Thread the included steel hose clamps through the eyelets on the back of the Mounting Bracket and then lightly fasten them around the pole. Both hose clamps must be used for pole mounting. b. Using Two Brackets (Tilt) 1. Attach the two main sections of the bracket using the four included screws and lock nuts. This requires an optional bracket. 1. Attach the two main sections of the bracket using the four included screws and lock nuts. 2. 3. Install the bracket onto the AP using the included four screws. Thread the included steel hose clamps through the eyelets on the back of the Mounting Bracket and then lightly fasten them around the pole. Both hose clamps must be used for pole mounting. 2 2 Ground the AP Quick Start Guide 2.
(Optional) Connect a local LAN switch, computer or other device to the LAN (PoE Out) 1000BASE-T RJ-45 port. b. (Optional) Connect DC Power When not connected to a PoE source, wire the included DC terminal plug to a 1024 VDC, 0.5-1 A source to provide power to the AP. c. (Optional) Management Connections Connect an RJ-45 to DE-9 straight-through console cable and then configure the serial connection: 115200 bps, 8 characters, no parity, one stop bit, 8 data bits, and no flow control. 4 Check AP LEDs Ground the AP by connecting a ground wire to the grounding point on the device and to nearby good earth. 3 Install the 5G Antennas Install approved cellular 5G omni external antennas to improve coverage and performance. 5 Connect to the Web User Interface 1. Connect a PC directly to the APs LAN (PoE Out) port. Power and System LEDson green for normal operation. 3 Connect Cables a. Connect LAN Cables 2. 3. Set the PC IP address to be on the same subnet as the AP LAN port default IP address. (The PC address must start 192.168.1.x with subnet mask 255.255.255.0.) Enter the APs default IP address of 192.168.1.10 into the web browser address bar. Note: To connect to the web interface using the Uplink (PoE In) port, the IP address is automatically assigned through DHCP by default. If a DHCP server is unreachable, the Uplink(PoE) port reverts to a fallback IP address of 192.168.1.10. 4. Log in to the web interface using default settings:
Username = admin Password = admin Note: Port covers and cable glands should be tightned to a torque of 10 kgf.cm. 1. Connect Category 5e or better cable to the Uplink (PoE In) 1000BASE-T RJ-45 port. When connected to a PoE source, the Uplink (PoE In) port connection provides power to the unit. 3 Safety and Regulatory Information the limits for a 15 of the FCC Rules. These limits FCC Class B This equipment has been tested and found to comply with Class B digital device, pursuant to Part are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
guarantee that interference will Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. the FCC Rules. Operation is subject For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This operated with minimum distance 46 cm between the radiator and your body. equipment should be installed and Professional Installation Instructions 1. Installation personnel This product is designed for specific by qualified personnel who have regulations. A general user shall not attempt to install or modify the equipment configuration. knowledge of RF and its related applications and should be installed Quick Start Guide Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil contient des metteurs /
sont conformes au (x) RSS (s) exempts et Dveloppement conomique Canada. Lopration est soumise aux deux conditions suivantes:
rcepteurs exempts de licence qui de licence dInnovation, Sciences
(1) Cet appareil ne doit pas provoquer dinterfrences.
(2) Cet appareil doit accepter toute interfrence, y compris les interfrences susceptibles de provoquer un fonctionnement indsirable de lappareil. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes mmes canaux. de satellites mobiles utilisant les CE Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This operated with minimum distance 20 cm between the radiator and your body. equipment should be installed and The device is restricted to indoor 5150 to 5350 MHz frequency range. use only when operating in the All operational modes:
2.4 GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ax (HE20), 802.11ax (HE40) 5 GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac
(VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ax (HE20), 802.11ax (HE40), 802.11ax (HE80) BLE 2.4 GHz: 802.15.1 The frequency and maximum transmitted power limit in EU are listed as below:
2. Installation location To meet regulatory RF exposure requirements, this product shall be installed at a location where, during normal operations, the radiating antenna is at least 45 cm away from any nearby persons. 2412-2472 MHz: 20 dBm 5150-5350 MHz: 23 dBm 5500-5700 MHz: 30 dBm 3. External antenna Use only the antennas which have Using non-approved antenna(s) is prohibited and may produce unwanted spurious or excessive RF transmitting power which may lead to a violation of FCC limits. been approved by the applicant. 4. Installation procedure Please refer to this equipment's user manual for the procedure details. 5. Warning The installation position must be carefully selected so that the final output power does not exceed the regulations. Violation of output power regulations could lead to serious federal penalties. limit set forth in relevant AT DE FR LI NO SK BE DK HR LT PL TR EE HU LU PT UK BG CH CY CZ EL IE LV ES IS FI IT MT NL RO SE SI The abbreviations of the countries, as prescribed in above table, where any restrictions on putting into service or any requirements for authorization of use exist. 4 Quick Start Guide CE Mark Declaration of Conformance for EMI and Safety (EEC) Hardware Specifications This information technology equipment is in compliance with the Directive 2014/53/EU and Directive 2014/35/EU. AP Chassis The Declaration of Conformity (DoC) can be obtained from www.edge-core.com -> support -> download. Weight X.XX kg (X.XXX lb) Size (WxDxH) 230 x 450 x 65 mm (9.06 x 17.72 x 2.56 in.) Warnings and Cautionary Messages Warning: This product does not contain any serviceable user parts. Warning: Installation and removal of the unit must be carried out by qualified personnel only. Network Interfaces Ports Temperature Operating: -40 C to 65 C (-40 F to 149 F) Storage: -40 C to 70 C (-40 F to 158 F) Humidity Operating: 5% to 95% (non-condensing) Uplink (PoE In) RJ-45 Port: 1000BASE-T, PoE PD LAN (PoE Out) RJ-45 Port: 1000BASE-T, PoE PSE Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment. Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards. 2.4 GHz Radio IEEE 802.11b/g/n 5 GHz Radio IEEE 802.11a/ac/n Bluetooth BLE/BT4.1 Radio Frequencies 2.42.4835 GHz (US and ETSI) US 5.155.25 GHz (lower band) 5.7255.825 GHz (upper band) Europe 5.155.25 GHz, 5.255.35, 5.475.725 GHz Power Specifications PoE Input Power 22.4 W max 802.3at-compliant DC Power 24 VDC, 1.09 A Regulatory Compliances Radio Emissions Safety EN 300 328 V2.2.2 (2.4G/BT-LE) EN 301 893 V2.1.1 (5G) EN 303 413 V1.1.1 (GPS) EN 50385 / EN 62311: 2017 (MPE) EN 301 489-1 V2.1.1 EN 301 489-17 V3.1.1 EN 301 489-52 V1.1.0 EN 62368-1: 2014 + A11: 2017 EN 60950-22: 2017 IEC 62368-1: 2014 (Second Edition) IEC 60529: 1989+AMD1: 1999+ AMD2:
2013CSV (IP55) Warranty Information and Technical Support Registering your product enables you to receive a more efficient warranty service. Be sure to register at www.edge-core.com. 5