FCC ID: HEDBSG12 BUSINESS SERVICE GATEWAY

BSG12aw BSG12aw Quick Installation Guide You can download all documents referenced in this Quick Installation Guide at www.nortel.com Tools and materials 1 Before you install the Business Services Gateway (BSG), ensure that you have the following package contents and materials:

Package Contents BSG unit power supply and power cord two omni-directional antennas console cable assembly Quick Installation Guide four self-adhesive rubber feet Regulatory sheet Hazardous Substance table Additional Required Materials (not included) RJ-11 telephony cable (WAN connection) two to three additional RJ-11 telephony cables

(if using analog devices) RJ-11 splitter (if only one analog line is available) Caution: Risk of equipment damage To avoid damaging the equipment, you must connect the BSG to an outlet with a third-wire ground. Use the BSG with only the supplied BSG power supply and a three-wire power outlet. Installing the BSG unit For optional methods to install your BSG, see the BSG8ew and BSG12ew/aw/tw 1.0 Installation Guide (NN47928-302). 2 Attach the four self-adhesive rubber feet to the bottom of the BSG by peeling off the paper backing and placing the feet on the unit. Attach feet here 3 Position the BSG on a desktop. Make sure you leave enough space around the unit for ventilation and access to the cables. 4 5 Install the power supply next to the BSG. The power supply must be within 1.5 m (5 ft) of the BSG and within 1.5 m (5 ft) of the AC power outlet (wall outlet or universal power supply). Connect the 48V DC 4-pin DIN power supply connector into either of the power outlets at the back of your BSG. Two power outlets 6 Connect one end of the AC power cord into the AC power supply. Plug the other end of the AC power cord into the AC power outlet

(wall outlet or universal power supply). The System LED on the front panel lights up. Connecting LAN devices (VoIP phones and PCs) 7 Plug one end of a standard Ethernet cable into one of the twelve LAN ports on the front of your BSG. Plug the other end of the Ethernet cable into your LAN device, such as a VoIP phone or PC. PoE/Link/Act LEDs LAN ports 8 Ensure that the corresponding LAN port PoE/Link/Act LED lights up. The corresponding LED will come on only if the device connecting to that port is powered on. ADSL port Connecting the WAN 9 Plug one end of an RJ-11 telephone cable into the ADSL port on the front of the BSG. Plug the other end of the cable into the telephone jack on the wall. Attach the omni-directional antennas to the wireless LAN antenna connectors on the back of the BSG. Optional installations Connecting wireless 10 Connecting analog or fax devices 11 Plug one end of an RJ-11 telephone cable into either of the FXS analog telephone (RJ-11) ports on the front of the BSG. Plug the other end of the cable into the analog device. FXS ports FXO port Console port Connecting the Public Switched Telephone Network 12 Plug one end of an RJ-11 telephone cable into the FXO analog line

(RJ-11) port on the front of the BSG. Plug the other end of the cable into the telephone jack on the wall. System LED Configuring the initial system settings Complete the following steps using the BSG Quick Start Wizard. Before you start, contact your Internet service provider (ISP) to obtain your user name, password, and encapsulation type information (Ethernet, PPPoE). 13 14 15 16 17 18 19 From a PC connected to the LAN, open a new Web browser, type http://192.168.1.1 into the address bar, and press Enter to start the Web user interface. In the Login window, enter your user name (nnadmin) and password

(PlsChgMe!), and Click Login. In the navigation pane on the left, click Quick Start Wizard. Click the blue forward button to start the wizard. Enter your ISP name, user name, and password, and confirm your password by entering it again. For more information about additional settings within the Quick Start Wizard, see the BSG8ew and BSG12ew/aw/tw 1.0 Configuration Guide (NN47928-500). Click Next and enter information on each wizard page as required. On the Review Data page, click Continue. Congratulations! You have successfully configured the Nortel Business Services Gateway!

N0156580 NN47928-306 Standard 01.01 Printed in Canada. Copyright Nortel Networks Limited 2007. All Rights Reserved

BSG12ew BSG12ew Quick Installation Guide You can download all documents referenced in this Quick Installation Guide at www.nortel.com Tools and materials 1 Before you install the Business Services Gateway (BSG), ensure that you have the following package contents and materials:

4 5 Install the power supply next to the BSG. The power supply must be within 1.5 m (5 ft) of the BSG and within 1.5 m (5 ft) of the AC power outlet (wall outlet or universal power supply). Connect the 48V DC 4-pin DIN power supply connector into either of the power outlets at the back of your BSG. Two power outlets Package Contents BSG unit power supply and power cord two omni-directional antennas console cable assembly Quick Installation Guide four self-adhesive rubber feet Regulatory sheet Hazardous Substance table standard Ethernet cable (WAN connection) two to three RJ-11 telephony cables (if using analog devices) Additional Required Materials (not included) Caution: Risk of equipment damage To avoid damaging the equipment, you must connect the BSG to an outlet with a third-wire ground. Use the BSG with only the supplied BSG power supply and a three-wire power outlet Installing the BSG unit For optional methods to install your BSG, see the BSG8ew and BSG12ew/aw/tw 1.0 Installation Guide (NN47928-302). 2 Attach the four self-adhesive rubber feet to the bottom of the BSG by peeling off the paper backing and placing the feet on the unit. Attach feet here 3 Position the BSG on a desktop. Make sure you leave enough space around the unit for ventilation and access to the cables. 6 Connect one end of the AC power cord into the AC power supply. Plug the other end of the AC power cord into the AC power outlet

(wall outlet or universal power supply).The System LED on the front panel lights up. Connecting LAN devices (VoIP phones and PCs) 7 Plug one end of a standard Ethernet cable into one of the eleven LAN ports on the front of your BSG. Plug the other end of the Ethernet cable into your LAN device, such as a VoIP phone or PC. PoE/Link/Act LEDs LAN ports 8 Ensure that the corresponding LAN port PoE/Link/Act LED lights up. The corresponding LED will come on only if the device connecting to that port is powered on. Connecting the WAN 9 Plug one end of the standard Ethernet cable into the WAN port (port 12) of the BSG. Plug the other end into the service providers cable modem or DSL modem. WAN port Attach the omni-directional antennas to the wireless LAN antenna connectors on the back of the BSG. Optional installations Connecting wireless 10 Connecting analog or fax devices 11 Plug one end of an RJ-11 telephone cable into either of the FXS analog telephone

(RJ-11) ports on the front of the BSG. Plug the other end of the cable into the analog device. FXS ports FXO port Console port System LED Connecting the Public Switched Telephone Network 12 Plug one end of an RJ-11 telephone cable into the FXO analog line (RJ-11) port on the front of the BSG. Plug the other end of the cable into the telephone jack on the wall. Configuring the initial system settings Complete the following steps using the BSG Quick Start Wizard. Before you start, contact your Internet service provider (ISP) to obtain your user name, password, and encapsulation type information (Ethernet, PPPoE). 13 14 15 16 17 18 19 From a PC connected to the LAN, open a new Web browser, type http://192.168.1.1 into the address bar, and press Enter to start the Web user interface. In the Login window, enter your user name (nnadmin) and password

(PlsChgMe!), and click Login. In the navigation pane on the left, click Quick Start Wizard. Click the blue forward button to start the wizard. Enter your ISP name, user name, and password, and confirm your password by entering it again. For more information about additional settings within the Quick Start Wizard, see the BSG8ew and BSG12ew/aw/tw 1.0 Configuration Guide (NN47928-500). Click Next and enter information on each wizard page as required. On the Review Data page, click Continue. Congratulations! You have successfully configured the Nortel Business Services Gateway!

N0153680 NN47928-304 Standard 01.01 Printed in Canada. Copyright Nortel Networks Limited 2007. All Rights Reserved

BSG12tw BSG12tw Quick Istallation Guide You can download all documents referenced in this Quick Installation Guide at www.nortel.com Tools and materials 1 Before you install the Business Services Gateway (BSG), ensure that you have the following package contents and materials:

4 5 Install the power supply next to the BSG. The power supply must be within 1.5 m (5 ft) of the BSG and within 1.5 m (5 ft) of the AC power outlet (wall outlet or universal power supply). Connect the 48V DC 4-pin DIN power supply connector into either of the power outlets at the back of your BSG. Two power outlets Package Contents BSG unit power supply and power cord two omni-directional antennas console cable assembly Quick Installation Guide four self-adhesive rubber feet Regulatory sheet Hazardous Substance table Additional Required Materials (not included) two to three RJ-11 telephony cables (if using analog devices) Caution: Risk of equipment damage To avoid damaging the equipment, you must connect the BSG to an outlet with a third-wire ground. Use the BSG with only the supplied BSG power supply and a three-wire power outlet. Installing the BSG unit For optional methods to install your BSG, see the BSG8ew and BSG12ew/aw/tw 1.0 Installation Guide (NN47928-302). 6 Connect one end of the AC power cord into the AC power supply. Plug the other end of the AC power cord into the AC power outlet

(wall outlet or universal power supply).The System LED on the front panel lights up. Connecting LAN devices (VoIP phones and PCs) 7 Plug one end of a standard Ethernet cable into one of the twelve LAN ports on the front of your BSG. Plug the other end of the Ethernet cable into your LAN device, such as a VoIP phone or PC. PoE/Link/Act LEDs LAN ports 2 Attach the four self-adhesive rubber feet to the bottom of the BSG by peeling off the paper backing and placing the feet on the unit. 8 Ensure that the corresponding LAN port PoE/Link/Act LED lights up. The corresponding LED will come on only if the device connecting to that port is powered on. Attach feet here Connecting the WAN 9 Plug the T1/E1 connection into either of the T1/E1 ports on the BSG. 3 Position the BSG on a desktop. Make sure you leave enough space around the unit for ventilation and access to the cables. T1/E1 ports Optional installations Connecting wireless 10 Attach the omni-directional antennas to the wireless LAN antenna connectors on the back of the BSG. Connecting analog or fax devices 11 Plug one end of an RJ-11 telephone cable into either of the FXS analog telephone

(RJ-11) ports on the front of the BSG. Plug the other end of the cable into the analog device. System LED FXS ports FXO port Console port Connecting the Public Switched Telephone Network 12 Plug one end of an RJ-11 telephone cable into the FXO analog line (RJ-11) port on the front of the BSG. Plug the other end of the line into the telephone jack on the wall. Configuring the initial system settings Complete the following steps using the BSG Quick Start Wizard. Before you start, contact your Internet service provider (ISP) to obtain your user name, password, and encapsulation type information (Ethernet, PPPoE). 13 14 15 16 17 18 19 From a PC connected to the LAN, open a new Web browser, type http://192.168.1.1 into the address bar, and press Enter to start the Web user interface. In the Login window, enter your user name (nnadmin) and password

(PlsChgMe!), and click Login. In the navigation pane on the left, click Quick Start Wizard. Click the blue forward button to start the wizard. Enter your ISP name, user name, and password, and confirm your password by entering it again. For more information about additional settings within the Quick Start Wizard, see the BSG8ew and BSG12ew/aw/tw 1.0 Configuration Guide (NN47928-500). Click Next and enter information on each wizard page as required. On the Review Data page, click Continue. Congratulations! You have successfully configured the Nortel Business Services Gateway!

N0156581 NN47928-307 Standard 01.01 Printed in Canada. Copyright Nortel Networks Limited 2007. All Rights Reserved

Regulatory and Safety Information Save these instructions North American Regulations - Please read Carefully This Class A device complies with Part 68 and Part 15 of the FCC Rules and the requirements adopted by the ACTA. This device meets the applicable Industry Canada specifications including ICES-003 EMI requirements. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. Do not attempt to repair this equipment. If you experience trouble, write for warranty and repair information.:

USA Nortel Networks 640 Massman Drive Nashville, TN, USA 37210 For warranty and repair service outside the USA or Canada, please contact your distributor. Canadian Notice The Industry Canada designation identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). Industry Canada does not guarantee the equipment will operate to the user's satisfaction. This device has been designed to operate with an antenna having a maximum gain of [x] dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. Federal Communications Commission (FCC) Notice FCC registration number: This telephone equipment complies with Part 68, Rules and Regulations, of the FCC for connection to the Public Switched Telephone Network. Your connection to the Public Switched Telephone Network must comply with these FCC rules:

Canada Nortel Repair Service Centre 30 30 Norelco Drive Weston Ontario, Canada M9L 2X6 Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. See installation instructions for details. Use only an FCC Part 68-compliant Universal Service Order Code (USOC) network interface jack, as specified in the installation instructions, to connect to the Public Switched Telephone Network. If the equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of the product may be required. But if advance notice isnt practical, the telephone company will notify you as soon as possible. You will also be advised of your right to file a complaint with the FCC, if you believe it is necessary. Ringer Equivalence Number (REN) The REN provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed 5. The telephone company may make changes to its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. Connection to party line services is subject to state tariffs. Do not connect this equipment to party lines. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. EMI/EMC (FCC Part 15) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, and as an intentional transmitter pursuant to Part 15 of the FCC Rules and Industry Canada RSS210 requirements. These limits are designed to provide reasonable protection against harmful interference. This equipment generates, uses and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. North American Regulations continued Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. WARNING: To comply with FCC radio frequency (RF) exposture limits, install this device a minimum of 7.9 inches

(20 cm) away from individuals. Important Safety Instructions The following safety instructions cover the installation and use of the Product. Read carefully and retain for future reference. Installation WARNING: To avoid electrical shock hazard to personnel or equipment damage observe the following precautions when installing telephone equipment:

1. Never install telephone, LAN or WAN wiring during a lightning storm. 2. Never install telephone, LAN or WAN jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch uninsulated telephone, LAN or WAN wires or terminals unless the line has been disconnected at the network interface. 4. Use caution when installing or modifying telephone, LAN or WAN lines. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product. Use When using your equipment, basic safety precautions should always be followed to reduce risk of fire, electric shock and injury to persons, including the following:

1. Read and understand all instructions. 2. Follow the instructions marked on the product and in the User and Maintenance documentation. 3. Unplug this product (or host equipment) from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. basement, or near a swimming pool. 4. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet 5. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. walking on it. 6. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided. 7. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons 8. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock. 9. Never spill liquid of any kind on the product. 10. To reduce the risk of electric shock do not disassemble this product, but have it sent to a qualified service person when some service or repair work is required. 11. Unplug this product (or host equipment) from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a) When the power supply cord or plug is damaged or frayed. b) If the product has been exposed to rain, water or liquid has been spilled on the product, disconnect and allow the product to dry out to see if it still operates; but do not open up the product. c) If the product housing has been damaged. d) If the product exhibits a distinct change in performance. 12. CAUTION: To eliminate the possibility of accidental damage to cords, plugs, jacks, etc., do not use sharp instruments during the assembly procedures 13. WARNING: Ensure the correct connections are being made to the equipment. Incorrect connections may result in a shock or fire hazard. 14. Save these instructions. Renseignements sur la rglementation et la scurit Conservez ces directives Rglements pour lAmrique du Nord Veuillez lire attentivement ce qui suit Cet appareil de classe A est conforme aux sections 68 et 15 des rglements de la FCC et aux rglements adopts par lACTA. Cet appareil est conforme aux spcifications ICES-0003 dIndustrie Canada concernant les interfrences lectromagntiques. Lutilisation de cet appareil est soumise aux deux conditions suivantes : (1) Cet appareil ne doit pas provoquer dinterfrences nuisibles et; (2) Cet appareil doit supporter les interfrences, y compris celles susceptibles de nuire son bon fonctionnement. Le cas chant, la rparation du matriel homologu doit tre coordonne par un reprsentant dsign par le fournisseur. En cas de rparations ou de modifications effectues par lutilisateur ou de mauvais fonctionnement du matriel, lentreprise de tlcommunications peut demander lutilisateur de dbrancher lappareil. Pour sa propre protection, lutilisateur doit sassurer que tous les fils de mise la terre du service public dlectricit, des lignes tlphoniques et des canalisations deau intrieures en mtal, sil y a lieu, sont raccords ensemble. Cette mesure de scurit est particulirement importante dans les rgions rurales. AVERTISSEMENT : Lutilisateur ne doit pas tenter dtablir lui-mme le raccordement de mise la terre. Il doit faire appel un service dinspection des installations lectriques ou un lectricien, selon le cas. Nessayez pas de rparer cet appareil. Si vous avez des problmes, communiquez par crit pour obtenir de plus amples renseignements sur la garantie et la rparation de votre appareil :

tats-Unis Nortel Networks 640 Massman Drive Nashville, TN, USA 37210 Pour toute question lie la garantie et aux services de rparation hors des tats-Unis et du Canada, communiquez avec votre distributeur. Avis lintention des Canadiens La dsignation Industrie Canada confirme que ce matriel est homologu. Elle atteste que le matriel est conforme aux normes de protection, dexploitation et de scurit des rseaux de tlcommunications prescrites dans la documentation approprie relative aux exigences techniques de lquipement terminal. Industrie Canada ne garantit toutefois pas que le matriel fonctionnera la satisfaction de lutilisateur. Avis de la Federal Communications Commission (FCC) Numro denregistrement de la FCC : Ce matriel tlphonique est conforme aux exigences de la section 68 des rglements de la FCC relatives au raccordement au rseau tlphonique public commut. Le raccordement au rseau tlphonique public commut doit tre conforme aux rglements suivants de la FCC :

Canada Centre de service de rparations Nortel n30 30, Norelco Drive Weston Ontario, Canada M9L 2X6 Avant dinstaller le matriel, lutilisateur doit sassurer quil est permis de le raccorder aux installations de lentreprise locale de tlcommunications. Le matriel doit galement tre install en suivant une mthode approuve de raccordement. Labonn doit savoir que la conformit aux normes nonces ci-dessus ne constitue pas une garantie contre la possibilit dune dgradation du service dans certaines conditions. Reportez-vous aux directives dinstallation pour obtenir de plus amples renseignements. Nutilisez quune prise dinterface rseau du code de commande normalise (USOC) conforme la section 68 de la FCC, comme lindiquent les directives dinstallation, pour le raccordement au rseau tlphonique public commut. Si lquipement savre nuisible au rseau tlphonique, la compagnie de tlphone vous avisera lavance ou le plus tt possible que vous devrez peut-tre dconnecter temporairement le produit. Mais si elle ne peut vous informer lavance, elle vous informera le plus tt possible. Vous serez galement averti de votre droit de porter plainte auprs de la FCC. Indice dquivalence de sonnerie (IES) Le IES fournit une indication du nombre maximal de terminaux qui peuvent tre connects une interface tlphonique. La terminaison dune interface peut tre connecte une combinaison de diffrents appareils tant que la somme des IES ne dpasse pas 5. La compagnie de tlphone peut modifier ses installations, son quipement, son service ou ses mthodes, ce qui pourrait perturber le fonctionnement de lappareil. Le cas chant, la compagnie de tlphone vous avertira lavance pour que vous puissiez prendre les mesures ncessaires et viter linterruption de votre service tlphonique. des lignes partages. Si votre domicile est dot dun systme dalarme reli la ligne tlphonique, assurez-vous que linstallation de lappareil nempchera pas le systme dalarme de fonctionner correctement. Pour des informations sur les installations de matriel pouvant perturber les systmes dalarme, consultez votre compagnie de tlphone ou un installateur. Une connexion au service de ligne partage est soumise aux tarifs de ltat. Ne reliez pas ce matriel EMI/EMC (section 15 de la FCC) Remarque: Cet appareil a t test et jug conforme aux limites tablies pour un metteur numrique de classe A, conformment la section 15 des rglements de la FCC et aux normes dindustrie Canada portant sur les interfrence lectromagntiques. Ces limites visent assurer une protection raisonnable contre les interfrences pouvant nuire lappareil. Ce matriel gnre des radiofrquences pouvant nuire aux communications sil nest pas install et utilis conformment aux instructions. Lexploitation de cet appareil dans un secteur particulier est toutefois susceptible de produire des interfrences nuisibles. Si ce matriel cause des interfrences nuisibles la rception des missions de radio ou de tlvision, ce qui peut tre vrifi en mettant lteignant et en le rallumant, lutilisateur doit prendre lune des mesures suivantes pour corriger la situation :

Rorienter ou relocaliser lantenne de rception. Consulter le dtaillant. Augmenter la distance entre lappareil et le rcepteur touch. Brancher lappareil une prise lectrique dun circuit diffrent de celui auquel le rcepteur est branch. Rglements pour lAmrique du Nord (suite) Modifier cet appareil sans le consentement de la partie responsable de la conformit peut entraner la rvocation de votre droit dutilisation lutiliser. Consignes de scurit importantes Les consignes de scurit suivantes doivent tre appliques lors de linstallation et de lutilisation du produit. Veuillez prendre le temps de les lire, puis conservez-les pour usage ultrieur. Installation AVERTISSEMENT : Pour viter tout dommage matriel et tout risque de choc lectrique, observez les mesures de scurit ci-aprs lorsque vous installez du matriel tlphonique :

1. Ninstallez jamais de cblage tlphonique ou de rseau pendant un orage. 2. Ninstallez jamais de prises tlphoniques ou de rseau dans des endroits humides, sauf si elles soient conues 3. Ne touchez jamais les bornes ou les conducteurs tlphoniques ou de rseau non isols sans dabord dbrancher cet effet. la ligne. 4. Soyez prudent lorsque vous installez ou modifiez des lignes tlphoniques ou de rseau. Dans la documentation accompagnant lappareil, un point dexclamation lintrieur dun triangle quilatral indique la prsence de directives importantes concernant lexploitation et lentretien (maintenance). Utilisation Lorsque vous utilisez votre matriel tlphonique, il importe de respecter les mesures de scurit de base suivantes de faon rduire les risques dincendie, de choc lectrique et de blessure. 1. Lisez les directives et assurez-vous de bien les comprendre. 2. Suivez les instructions indiques sur lappareil et dans la documentation. 3. Dbranchez le cble dalimentation (ou le matriel hte) de la prise murale avant le nettoyage. Nutilisez pas de nettoyant liquide ou en arosol. Servez-vous dun linge humide. 4. Nutilisez pas cet appareil prs de leau, notamment prs dune baignoire, dun lavabo, dun vier ou dun bac laver, dans un sous-sol humide ou prs dune piscine. 5. vitez de placer ce produit sur un chariot, un support ou une table instable. Il pourrait tomber et subir de graves dommages. lectrique. 6. Ne placez jamais cet appareil sur un radiateur ou une bouche de chaleur, ou prs de ceux-ci. Il ne doit pas non plus tre plac dans un espace clos moins que la ventilation ny soit adquate. 7. Ne dposez aucun objet sur le cordon dalimentation. vitez de placer cet appareil dans un endroit o le cordon pourrait tre endommag par la circulation. 8. Ne surchargez pas les prises murales ni les cordons prolongateurs afin dviter les risques dincendie ou de choc 9. Veuillez ne pas renverser de liquide sur lappareil. 10. Afin de diminuer les risques de choc lectrique, ne dmontez pas lappareil. Sil doit tre entretenu ou rpar, expdiez-le une personne qualifie du service de rparation. 11. Dans les cas suivants, dbranchez le cordon dalimentation (ou le matriel hte) de la prise murale, et faites appel au personnel qualifi du service de rparation :

a) La fiche ou le cble dalimentation est endommag ou dnud. b) Si lappareil a t expos du liquide, dbranchez-le et laissez-le scher afin de voir sil fonctionne toujours, mais vitez de louvrir. c) Le botier a t endommag. d) Le rendement de lappareil semble se dgrader considrablement. 12. AVERTISSEMENT: Pour viter tout risque de dommage aux cbles, aux fiches ou aux prises, nutilisez pas doutils 13. AVERTISSEMENT: Assurez-vous deffectuer les connexions appropries. Les erreurs de connexion peuvent causer tranchants pour assembler le matriel. des risques dlectrocution et dincendie. 14. Conservez ces directives. Informacin sobre reglamentos y seguridad Guarde estas instrucciones Canad Nortel Repair Service Centre 30 30 Norelco Drive Weston Ontario, Canada M9L 2X6 Normas para Amrica del Norte (lea detenidamente) Este dispositivo Clase A cumple con las disposiciones de los Apartados 68 y 15 de las Reglas de FCC y los requisitos adoptados por ACTA. El dispositivo cumple con las especificaciones vigentes de Industry Canada, incluso los requisitos ICES-003 EMI. Su uso est sujeto a las siguientes condiciones: (1) el dispositivo no debe generar interferencias nocivas, y

(2) debe admitir las interferencias recibidas, incluso las que pueden causar un funcionamiento no deseado. Toda reparacin efectuada en un equipo autorizado debe ser coordinada por un representante designado por el distribuidor. Toda reparacin, modificacin o uso incorrecto del equipo por parte del usuario puede ser causa suficiente para que la empresa de telecomunicaciones solicite su desconexin. A los fines de su propia proteccin, el usuario debe verificar que la conexin a tierra de los servicios elctricos, las lneas telefnicas y el sistema de caeras metlicas, si lo hubiere, se realice de forma conjunta. Esta medida de precaucin resulta especialmente importante en las zonas rurales. PRECAUCIN: No intente realizar estas conexiones. Comunquese con el organismo responsable de las inspecciones elctricas o un electricista, segn corresponda. No trate de reparar usted mismo(a) este equipo. Ante cualquier problema, solicite informacin sobre la garanta y las reparaciones por correo:

Estados Unidos Nortel Networks 640 Massman Drive Nashville, TN, USA 37210 Para obtener servicio de garanta y reparaciones en otros pases, pngase en contacto con su distribuidor. Aviso para Canad La designacin Industry Canada indica que el equipo est certificado, es decir, que cumple los requisitos de proteccin, operacin y seguridad para redes de telecomunicaciones estipulados en los documentos pertinentes de requisitos tcnicos para equipos terminales. Industry Canada no garantiza que el equipo funcione a satisfaccin del usuario. Aviso de la Comisin Federal de Comunicaciones (FCC) Nmero de registro de FCC: este telfono cumple con las disposiciones del Apartado 68 de los reglamentos de FCC en lo que respecta a conexin directa a la Red telefnica conmutada pblica. Su conexin a la Red telefnica conmutada pblica debe cumplir con las siguientes reglas de FCC:

Antes de instalar el equipo, el usuario debe verificar que pueda conectarse a los dispositivos proporcionados por la empresa de telecomunicaciones local. Asimismo, el equipo debe ser instalado de acuerdo con los procedimientos de conexin autorizados a tal efecto. No obstante, recuerde que el cumplimiento de estas condiciones no impide necesariamente que el servicio resulte defectuoso en determinadas circunstancias. Consulte las instrucciones de instalacin para obtener ms informacin. Para conectarse a la Red telefnica conmutada pblica utilice slo un conector de interfaz de red de Cdigo universal de pedido de servicio (USOC) que cumpla con el Apartado 68 de FCC, tal como se especifica en las instrucciones de instalacin. La compaa de telfonos puede interrumpir temporalmente el servicio, previa notificacin, si determina que el equipo ocasiona problemas en la red telefnica. En caso de no ser factible notificarlo por adelantado, la compaa le dar aviso con la mayor brevedad posible. Asimismo, le informar de su derecho de presentar una queja ante FCC si lo considera necesario. Nmero de equivalencia del timbre (REN) El nmero de equivalencia de timbre (REN) indica el nmero mximo de terminales que pueden conectarse a una interfaz telefnica. La terminacin de una interfaz puede constar de cualquier combinacin de aparatos. El nico requisito es que el total de nmeros de equivalencia de timbre no sea superior a 5. La compaa telefnica puede decidir efectuar modificaciones en sus instalaciones, equipos, operaciones o procedimientos que podran afectar el funcionamiento del equipo. En tal caso, le avisar con suficiente anticipacin para que pueda hacer las modificaciones pertinentes a fin de no interrumpir el servicio. La conexin con los servicios de lnea colectiva queda sujeta a tarifas estatales. No conecte el equipo a lneas colectivas. Si su hogar cuenta con un equipo de alarma con cableado especial conectado a la lnea telefnica, controle que la instalacin del equipo no lo desactive. Si tiene dudas, consulte a su compaa telefnica o a un instalador especializado. EMI/EMC (Apartado 15 de FCC) NOTA: Las pruebas realizadas han permitido determinar que el equipo cumple con las restricciones establecidas para los dispositivos digitales Clase A y acta como transmisor de conformidad con el Apartado 15 de las Reglas de FCC y los requisitos RSS210 de Industry Canada. El propsito de estas restricciones consiste en proporcionar un nivel razonable de proteccin contra las interferencias nocivas. Este equipo genera, utiliza e irradia energa de radiofrecuencia. Por ende, debe ser instalado y utilizado de acuerdo con las instrucciones proporcionadas para evitar que cause interferencias nocivas en las comunicaciones. No obstante, no existen garantas respecto de las interferencias que pueden producirse en una instalacin determinada. Si el equipo origina interferencias nocivas en la seal de radio o televisin, lo que puede determinarse al encenderlo y apagarlo, el usuario podr realizar uno o ms de los siguientes procedimientos para resolver el problema:

Reorientar o cambiar de lugar la antena receptora. Conectar el equipo a una toma que se encuentre en un circuito distinto del correspondiente al receptor. Consulte al proveedor. Aumentar la distancia entre el equipo telefnico y el aparato receptor. Normas para Amrica del Norte (continuacin) Todo cambio o modificacin que no haya sido expresamente aprobada por la parte responsable del cumplimiento de las normas podra dejar sin efecto la autorizacin del usuario para operar el equipo. Medidas importantes de seguridad La instalacin y el uso del producto requieren las medidas de seguridad que se indican a continuacin. Lalas con atencin y consrvelas para utilizarlas como referencia en el futuro. Instalacin ADVERTENCIA: Para evitar riesgos de descargas elctricas que pueden causar dao al personal o al equipo, tome las siguientes precauciones al instalar el equipo telefnico:

1. Nunca instale el cableado telefnico, de LAN o WAN durante una tormenta elctrica. 2. Nunca instale conectores telefnicos ni de LAN o WAN en lugares hmedos, a menos que el conector haya sido especficamente diseado para este tipo de espacios. 3. No toque cables o terminales de telfono, LAN o WAN sin aislante, a menos que la lnea telefnica haya sido desconectada en la interfaz con la red. 4. Sea prudente al instalar o modificar lneas telefnicas, de LAN o WAN. En la documentacin suministrada con el producto, la presencia del signo de exclamacin dentro de un tringulo equiltero se utiliza para indicar instrucciones importantes sobre funcionamiento y mantenimiento (servicio tcnico). Uso Siga siempre las precauciones bsicas de seguridad al usar el equipo para evitar riesgos de incendio, descargas elctricas o lesiones. Entre ellas:

1. Asegrese de leer y comprender correctamente todas las instrucciones. 2. Siga las instrucciones que aparecen en el producto y en la documentacin del usuario y de servicio tcnico. 3. Desconecte el producto (o el equipo host) de la toma de pared antes de limpiarlo. No utilice limpiadores lquidos ni en aerosol. Realice la limpieza por medio de un pao hmedo. 4. No utilice este producto cerca del agua; por ejemplo, cerca de una tina de bao, lavabo, un sumidero o una pileta para ropa, y tampoco sobre una superficie hmeda o cerca de una piscina. 5. No coloque el producto sobre un carro, soporte o mesa inestable pues podra caerse y sufrir graves daos. 6. Este producto nunca debe colocarse cerca o sobre un radiador o una salida de calefaccin. Tampoco se debe colocar en una instalacin empotrada sin ventilacin adecuada. 7. No apoye objetos sobre el cable de alimentacin ni coloque el producto en un sitio donde el cable pueda obstruir el 8. Las tomas de pared y los cables de extensin no deben sobrecargarse, pues podra originarse un incendio o una 9. Nunca vierta ningn tipo de lquido sobre el producto. 10. Para reducir el riesgo de descarga elctrica, no desarme el producto. Si requiere reparacin, envelo a un servicio paso y sufrir daos. descarga elctrica. tcnico calificado. 11. Desconecte el producto (o el equipo host) de la toma de pared y solicite servicio al personal calificado en las siguientes circunstancias:

a) Si el cable de alimentacin o el enchufe estn daados. b) Si el producto ha sido expuesto a la lluvia o al agua, o si se ha vertido otro tipo de lquido encima. De ser as, desconctelo y djelo secar para ver si todava funciona, pero no lo abra. c) Si la cubierta ha sido daada. d) Si el producto muestra un cambio notorio en su funcionamiento. 12. PRECAUCIN: Para eliminar la posibilidad de daar accidentalmente los cables, enchufes, conectores y otros elementos, no utilice instrumentos afilados durante el montaje. 13. ADVERTENCIA: Asegrese de realizar las conexiones correctas en el equipo. De lo contrario, existe el riesgo de que se produzca un incendio o descarga elctrica. 14. Guarde estas instrucciones. NN47928-101 Standard 01.01 N0153682 September 2007 Copyright Nortel Networks 2007 All Rights Reserved.