PORSCHE DESIGN | ACER MOUSE RS Quick Start Guide | Kurzanleitung | Guide de dmarrage rapide Guida rapida all'avvio | Gua de inicio rpido |
| Gua de inicio rpido |
| Panduan Ringkas |
Warranty booklet x 1 Battery x 2 1 2 3 h s i l g n E Package Contents Bluetooth & Wireless mouse x 1 Quick start guide x 1 Device Overview 1. Left button 2. Scroll wheel (3D) 3. Right button 4. Nano USB receiver 5. LED indicator 6. Optical sensor 7. Bluetooth button (mode switch) 8. USB receiver holder 9. Battery compartments 4 Turn the mouse on 1. Open the battery compartment cover at the back of the mouse. 2. Install 2 AAA batteries into the battery compartments. 3. Replace the cover. 4. The mouse is automatically ON. WARNING Make sure that the positive and negative ends are positioned correctly as labeled on the battery compartment. Connect your mouse Using the Nano USB receiver Plug the Nano USB receiver into your computer s USB Type-A port. Now you are ready to use the mouse. It s Plug & Play connectivity, no drivers required. Make sure the distance between your computer and mouse is within 10 meters. Pairing your mouse with Bluetooth 1. Press and hold the Bluetooth button at the back of your mouse for 2 seconds to switch to Bluetooth mode and start the initial pairing process. Press and hold the Bluetooth button for 5 seconds will start the pairing process again (or pairing with new device). 2. The LED starts to flash blue indicating that the mouse is in Bluetooth mode and ready to pair. 3. Start the Bluetooth pairing wizard on your computer and follow the instructions.
- Once your mouse is paired successfully, you do not need to pair it again when using the mouse next time.
- If the pairing is unsuccessfully, your mouse will enter Sleep mode after flashing blue about 3 minutes. Please repeat step 1-3 above to restart the pairing process. NOTE NOTE 5 6 7 8 9 1 Mode switch Press the Bluetooth button for 2 seconds to toggle your mouse between Wireless and Bluetooth mode. LED flashes blue for 3 seconds indicating that the mouse is in Bluetooth mode. LED flashes red for 3 seconds indicating mouse is in Wireless mode. E n g l i s h DPI switch You can cycle through the DPI options by repeatedly pressing Bluetooth button for 1 second. There are three available options for selection: 800/1600/3200. Low battery notification When the battery level is low, the flashing red will stay on if the mouse is in use. After stopping using the mouse, the LED flashes red for 10 seconds and then off. NOTE The mouse will maintain a low current consumption when entering Sleep mode. It is recommended to remove batteries if the mouse will not be used for an extended period. Specifications Model: AMR030 Operation System: Windows 7 or later
(Windows 8 or later / Mac OS X or later are required for BT feature) Bluetooth: 5.0 or later Connection Type: RF & BT Interface: USB Type-A port (Dongle) DPI: 800/1600/3200 Weight: 92g 5g (with AAA battery x2) Dimensions (L x W x H):
114.3 x 60 x 27.36 mm Caution Do not disassemble the device or operate the device under abnormal conditions. Do not submerge the device in water. If the device could not be functional, or there was thermal abnormal situation, please re-plug in the USB. If you still encounter problems after going through the corrective measures, please contact your dealer or an authorized service center for assistance. For more information, please visit our website at www.acer.com. Environment Temperature:
Operating: 5 C to 40 C Non-operating: -10 C to 70 C Humidity (non-condensing):
Operating: 10% to 60%
Non-operating: 10% to 60%
Manufacturer address Acer Inc. 8F, 88, Sec. 1, Xintai 5th Rd. Xizhi, New Taipei City 221, Taiwan NOTE All images and information in this document are for reference only and are subject to change without notice. For the latest specification, please visit our official website: www.acer.com. 2 5 6 7 8 9 x 1 x 2 1 2 3 4
/ x 1 x 1 1. 2. 3D 3. 4. USB 5. LED 6. 7. 8. USB 9. 1. 2. 2 AAA 3. 4. USB USB USB Type-A 10 1. 2 5 2. LED 3.
- 3 1-3 3 2 LED 3 LED 3 DPI 1 DPI 800/1600/3200 LED 10 AMR030 Windows 7 Windows 8 /
Mac OS X 5.0 USB Type-A DPI 800/1600/3200 92g 5g AAA x2 x x 114.3 x 60 x 27.36 USB www.acer.com 5 C 40 C
-10 C 70 C 10% 60%
10% 60%
221 88 8 www.acer.com 4 x 1 x 1 1. 2. (3D) 3. 4. Nano USB 5. LED 6. 7. 8. USB 9. x 1 x 2 1 2 3 4 1. 2. 3. 4. Nano USB Nano USB USB Type-A 10 1. 2 5 2. LED 3.
- 3 1-3 5 5 6 7 8 9 2 LED 3 LED 3 DPI 1 DPI 800/1600/3200 LED 10 AMR030 Windows 7 Windows 8
/ Mac OS X 5.0 USB Type-A DPI800/1600/3200 92 5 x x 114.3 x 60 x 27.36 USB www.acer.com 5 C 40 C
-10 C 70 C 10% 60%
10% 60%
221 88 8 www.acer.com 6 Europe EU Declaration of Conformity We declare under our sole responsibility that the product is conformity with all the essential requirements and other provisions of the European Council Directive RoHS Directive (2011/65/EU) and Radio Equipment Directive (2014/53/EU) issued by the Commission of the European Community. E n g l i s h This product must not be disposed of with your other household waste or treat them in compliance with the local regulations or contact your local city office, your household waste disposal service or the shop where you purchased the product. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which Increase the separation between the equipment and receiver. the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Notice: Canadian users Canada, Industry Canada (IC) Notices This device complies with Industry Canada license exempt RSS standard(s). 7 This Class B digital apparatus complies with Canadian ICES-003 and CAN ICES-3(B)/NMB-
3(B). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. h s i l g n E This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with ISED exposure compliance requirement, please follow operation instruction as documented in this manual. Canada, Cet appareil numrique de classe B est conforme aux normes canadiennes ICES-003 et RSS-
247. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d rences qui peuvent affecter son fonctionnement. interfrence et (2) cet appareil doit accepter toute interfrence, notamment les interf Cet quipement est conforme aux limites d exposition aux radiations tablies pour un environnement non contrl. Les utilisateurs finaux doivent suivre les instructions d utilisation spcifiques pour satisfaire la conformit l exposition aux RF. Pour maintenir la conformit aux exigences de conformit l exposition , veuillez suivre les instructions de fonctionnement dcrites dans ce manuel. Este equipamento opera em carater secundario, isto e, nao tem direito a protecao contra interferencia prejudicial, mesmo de estacoes do mesmo tipo, e nao pode causar interferencia a sistemas operando em carater primario. Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 8 E n g l i s h Equipment name AMR030 Type designation (Type) Restricted substances and its chemical symbols Lead
(Pb) Mercury Cadmium
(Hg)
(Cd) Hexavalent chromium
(Cr+6) Polybrominated biphenyls
(PBB) Polybrominated diphenyl ethers
(PBDE) Unit
(:AMR031) 1.0.1 wt %0.01 wt %
Note 1: Exceeding 0.1 wt % and exceeding 0.01 wt % indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. 2. Note 2: indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. 3. Note 3: The indicates that the restricted substance corresponds to the exemption. 9
, China RoHS, h s i l g n E Pb Hg Cd Cr(VI) PBB PBDE SJ/T11364
GB/T26572 GB/T26572 RoHS
10