Digital Proportional R/C System ACME TECH 3 Channel Systems Manual ACME TECH. (SHEN ZHEN) CO., LTD. TEL:86-755-2857 1661 FAX:86-755-2857 1053 ACME TECH. (SHENZHEN) CO., LTD. INSTRUCTION MANUAL Caution: This device complies with part15 of the FCC Rules. Operation is subject to the following two conditions :(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. 1Safety Instructions and Hazard Warnings This radio remote control is not a toy. Therefore it is not suitable for children under the age of 8. Children or young people under the age of 14 should only operate the remote control system when an adult is present. A radio remote-controlled model is also not a toy. For this reason, you must observe the special safety instructions of the model manufacturer when installing the receiver unit and during subsequent operation. If you are yet familiar with the handling of remote-controlled models, please contact an experienced model sportsperson or a model construction club. In electric models, do not connect the drive engine until the receiver unit has been completely installed. This way you prevent any sudden unintended start-up of the drive motor. Please check the functional safety of your model and the remote control unit before putting the device into operation. When doing so, make sure there is not visible damage, such as defective plug connections or damaged cables. All movable parts of the model must run smoothly, but must not have any play in their bearings. When the aerial is pressed in , the
- 1 -
ACME TECH. (SHENZHEN) CO., LTD. INSTRUCTION MANUAL device should still work within a range of approximately 25-30 metres. Before using the rechargeable batteries that are necessary for operating your remote control, you must charge them in accordance with the manufacturers specifications. If the power supply is too low due to empty batteries of empty rechargeable batteries, this lessens the range and you may loose control of your model. Please note that fully charged rechargeable batteries can supply extremely high voltages. In case of a short circuit, the wires can become very hot and cause severe skin burns. Do not expose the transmitter to direct sunlight or excessive heat for an extended period of time. Remove the (rechargeable) batteries from the device when you do not use it for a long period time. Do not leave the packaging material lying around carelessly since this may become a dangerous toy for children. 2Performance characteristic 1)Power Requirement:9.012.1V DC 2)Current Drain: 4.50mA(VDD=10V ) 3)Temperature (working): 070 4)Temperature (Preserving): -55+125 5)LCD demonstrates and the LED indicating lamp, turn off the lamp if having no the pressed key for 10 seconds.
- 2 -
ACME TECH. (SHENZHEN) CO., LTD. INSTRUCTION MANUAL 3Function Description 1)IC have a power supply switch(on/off),a trigger: control advance, backlash, back-draft; a direction controlling knob: control left or right steering; the third channel function key:CH3+,CH3-;The twelve function key: , + ,CH, SEL, DT1, DT1+, DT2, DT2+, DT3, DT3+, DT4, DT4+
2) Turn left the Steering Servo, make the motor turning left; Turn right the Steering Servo, make the motor turning right. Its movement scope is affected by the TRM_ST,SBT_ST, EPA-STEXP-STD/R-STSPD. When REV-ST is setted ON, it will make the operation reverse. Turn left the Steering Servo, make the motor turning right; Turn right the Steering Servo, make the motor turning left. 3) Pull the throttle, make the motor forward; Push the throttle , make the motor back. Its movement scope is affected by the TRM_TH, SBT_TH, EPA-THEXP-TH, ACC, ABSATL-BK. When REV-ST is set ON, it will make the operation reverse. Pull the throttle, make the motor back ; Push the throttle , make the motor forward. 4) When the vehicle is forward, back-draft or turning left or right, it will output the control signal of the channel 3.It is affected by the CH3-TR BMXSBT-3C ,CH3-P1, 2, 3, 4, PR,PL. 5) Press the ON/OFF switch right , it plays; Press the ON/OFF switch left and dumps, it stops all the movement.
- 3 -
ACME TECH. (SHENZHEN) CO., LTD. INSTRUCTION MANUAL 4.Operation Instruction After Press the ON/OFF switch right , there are two setting way:
(1) press the SEL key and open the power switch, enter System Function Setting; Not press the SEL key and open the power switch, then enter the Initial screen, after press the SEL key then enter the Ordinary Function Setting. Please refer to the table. 01 M0 System Function Setting PP SYS TM Cpy 01-10 Cpy 01-
L-1 LED-MD SEL Clr M01-01 Off CON D2 CH NAM 01 01 01 M 1 Fnc DT1-ST Fnc DT2-TH Fnc DT3-01 Fnc DT4-01 PP MOD-PP
- 4 -
ACME TECH. (SHENZHEN) CO., LTD. INSTRUCTION MANUAL Ordinary Function Setting CH SEL PP M01-01 10.5V M01-01 100% RB EPA-3C ABS-M D 100% LF EPA-3C 100%
EPA-TH 100%
EPA-ST SEL M01-01 SEL M01-02 SEL M01 - 10 100 SPD-RN 100 SPD-TN off REV-ST off REV-TH off REV-3C 0%
EXP-BK 0%
EXP-FW 0%
EXP-ST 0 ABS-DL 10 ABS-CY 50 ABS-PT 0%
ACC-BK 0%
ACC-FW oFF BMX-MD 100%
BMX-RT 0%
SBT-ST 0%
CH3 1P 100%
ATL-BK 0%
SBT-TH 0%
SBT-3C 0%
CH3 2P 0%
CH3 5P 0%
CH3 3P 0%
CH3 4P 0%
TRM-TH 0%
TRM-ST 100%
D/R-ST CH
- 5 -
ACME TECH. (SHENZHEN) CO., LTD. INSTRUCTION MANUAL
(2) System Function Setting a. copy the model control data:
On the Initial screen, press the SEL key simultaneously then entry MODEL COPY: 01-NN CPY,press the CH key from 01 to 10, and press +/- about one second, then copying the data. b. Initial the model control data:
Press the SEL key and entry the screen: NAM 01 CLR, After entering, press +/- key about one second, it will restore the current model control data to the default value, but will not change the PPM and the Brightness of LED. c. Setting the model control datas name:
Press the SEL key and entry the name setting screen NAM to NNN 01, press +/- key will change the character, press CH will change the revision position, then change NNN . d. Setting the Signal output model: use PPM model only now. e. Function of Adjusting Lever FNC-DT The function will choice the function of the trim lever and ATL level and D/R lever. You may choose the function:
ST: Adjust the Steering Trim value TH: Adjust the Throttle Trim value DR: Adjust the DR-ST AT: Adjust the ATL-BK E1: Adjust the EXP-ST
- 6 -
ACME TECH. (SHENZHEN) CO., LTD. INSTRUCTION MANUAL BK: Adjust the BMX-RT OFF: Turn-off the function of the key At the system function initial screen, press SEL many times then enter FNC-DT, then enter Fnc DT1-ST, press CH, enter DT2-TH,or DT3-DR , or DT4-AT, or DT1-ST; press +/- , enter ST or TH or DR or AT or E1 or BK or OF or ST f. Condition 2(COND2) Setting : the setting invalid g. Adjust the LED brightness: LED-MD At the system function initial screen, press SEL many times then enter LED-MD, press +/- , enter L0 or L1 or L2 or L3 or L4. L0 is the turn-off.
- 7 -