QUICK START GUIDE QUICK START GUIDE QUICK START GUIDE CARE AND WARNING D WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/panel PC technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,including interference that may cause undesired operation. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. The power consumption of the product in networked standby is 5.7W which all wired network ports are connected and all wireless network ports are activated. FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with the FCC & CEs RF exposure guidelines, place the product at least 20cm from near by persons. Adaptor with ferrite must be used with this equipment to ensure compliance with the Class B FCC limits. Power Adapter information:
Model No.: KSASB0241200150D5 INPUT: 100-240V~50/60Hz 0.6A OUTPUT: 12V 1.5A P R O D U C T S Add-On Products Roms Hule 8, 7100 Vejle, Denmark Europe Tel: +45 7944 7000 North America Tel: +1 (905) 655-9262 QUICK START GUIDE This quick guide will help you go through installation quickly Panel PC DS-1050 The colour and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. QUICK START GUIDE QUICK START GUIDE QUICK START GUIDE QUICK START GUIDE A CONTENTS Panel PC Quick Start Guide DC Power Adapter for US for EU for UK for AU Power Plug C INSTALLATION 1. Cables connection Step 1 Step 2 Step 3 Bracket Tape I/O Cover Set screw *2 2. Tape Mount Cables connection I/O Cover Installation Fix the set screw to secure the I/O cover B INDICATION 1 2 3 4 5 6 7 8 12 Step 1 Step 2 Step 3 Step 4 Metal Glass Plastic Attach tape on the back of bracket Place the bracket on the back side of the panel PC Fasten the set screw to secure the bracket and I/O cover Fix the Panel PC on the surface via using tape
* Please ensure the mounting surface is clean and smooth before using the tape. 3. Surface Mount Step 1 Step 2 Step 3 9 13 10 11 1 2 3 4 Micro SDHC ADB USB LAN (PoE+) 5 6 7 8 DC 12V USB Reset Audio Out 13 Display (DS-1050 is with touch display) 9 10 11 12 Side indicator light bar Front indicator light bar NFC (available on DS-10XX) Camera Install bracket on surface Assembly the Panel PC on the bracket Fasten the set screw to secure the bracket and I/O cover
* This panel PC is also compatible with VESA mounting 75mmx75mm and recommand to use M4 screws to lock. The suggested length of the M4 screw is that the thickness of VESA mounting bracket plus 8mm. For more information and support please visit:
https://www.add-on.com and https://www.add-on-support.com