A. CHANGING THE BATTERY The Two-Way remote transmitter is powered by one AAA Battery. When the power of icon shall be displayed on the LCD screen. When the old the battery weakens A battery is replaced, there will be beep sounds to indicate the power is back up on the transmitter The One-way remote is powered by one CR2032 Battery. To replace battery use a coin or small flat blade screwdriver to carefully pry apart case. 1 Click to buy NOW!PDF-XChange Viewerwww.docu-track.comClick to buy NOW!PDF-XChange Viewerwww.docu-track.com B. STANDARD LCD ICON CONFIGURATIONS:
Door Lock The lock icon will be displayed when the door are locked. System Armed Hidden Alarm Mode The security system arm with hidden alarm function
(silent alarm) Door Trigger (Zone 1) Door is illegally opened Trunk Trigger (Zone 2) Trunk is illegally opened Hood Trigger (Zone 3) Hood is illegally opened. Shock Sensor Trigger
(Zone 4) No Icon = Shock Bypass With Icon = With Shock Sensor Icon Flashing = Shock trigger Ignition Trigger (Zone 6) Ignition switch was illegally turned on. System Trigger or Panic mode 2 Door Unlock and Disarmed The unlock icon will be displayed when the door are unlocked and disarmed Valet Mode All the function shall be temporally on hold. The system has been triggered Door Ajar you have left a door lid ajar Trunk Ajar you have left a trunk lid ajar Hood Ajar you have left a hood lid ajar Tilt Sensor Trigger
(Zone 5) No Icon = Tilt Bypass With Icon = With Tilt Sensor Icon Flashing = Tilt Sensor trigger Warn Away Trigger No Icon = Warn-away Bypass With Icon = With Warn-away Icon Flashing = Warn-away trigger Trunk Release Click to buy NOW!PDF-XChange Viewerwww.docu-track.comClick to buy NOW!PDF-XChange Viewerwww.docu-track.com Engine Cranking Your vehicle engine cranking by remote control. Timer Control Start Engine starts automatically every 2 or 3 hours 24 hour repeat with cold starting Monitor the temperature 24 hours. and start if it is at or below the preset cold start temperature Interior Temperature Display The Vehicle Interior Temperature Defogger Engine Running Your vehicles engine is running Timer with Temperature Control Start Engine starts automatically every 2 or 3 hours, it will start at a specified temperature at the end of the timed cycle. Daily timer Start Start at the predetermined time of the next day Manual Transmission Mode (MTS) Driver Pager (Icon flash) 2nd Car Operation Button Lock Remote Transmission You are transmitting the signal to control unit. Low Battery Tone Mode Alarm Clock In-Range Indicator You are within the range of the remote control. Power Save Vibrating Mode Parking Meter Reminder when time is up for parking 3 Click to buy NOW!PDF-XChange Viewerwww.docu-track.comClick to buy NOW!PDF-XChange Viewerwww.docu-track.com C. REMOTE TRANSMITTER OPERATION:
Button System Function Remark Arm & Lock Doors Press the Lock button for a half second Silent Arm & Lock Doors Press and hold for 1.0 seconds Panic Function Press and hold for 3 seconds to Activate or Deactivate panic function Arm and Warn-Away Press Twice within Bypass Arm and Warn-Away &
Shock Sensor Bypass 2.0 sec. Arm and All Sensors Bypass Arm and Tilt Sensor Bypass 3 seconds. Press 3 times within 3 seconds. 2 times and hold the Press second times for 2.0 seconds Press the button first then press button Arm and Hidden Alarm Press the button first then Function Disarm & Unlock Doors Silent Disarm & Unlock Doors press button Press the Unlock button for a half second Press and hold for 1.0 seconds Passive Arming Bypass Press and hold for 3 seconds Disarm & Two Steps Door Unlock (optional) Press twice within 3 seconds Trunk Release Press and hold for 2 seconds Car Finder Switch Code for 2nd Car Operation Press Twice within 3 seconds. Press and hold for 2 seconds
-
-
-
-
-
-
+
-
-
4 Click to buy NOW!PDF-XChange Viewerwww.docu-track.comClick to buy NOW!PDF-XChange Viewerwww.docu-track.com Button System Function Remark Activate or Deactivate the Remote Start Press button once. Press
-
button if set to start safety mode. Runtime Reset Press and hold for 2 seconds Timer Start 24 hour repeat with cold starting Turbo Mode Press the button first then press button. Press the press and hold button first then button 1.5 seconds Press and hold both buttons for 2 seconds Aux 1 Timer Output Press together & release Aux 2 Timer Output Press together & release. Aux 3 Timer Output Press together & release. Aux 4 Timer Output Press together & release Aux 5 Timer Output Press together & release. Aux 6 Timer Output Press together & release. Shutdown Diagnostic Press and hold for 2 seconds Level / Move The Setting. Press F button once Light up he LCD indicator Press and hold for 1 second LCD Remote Program Setting Press and hold for 3 seconds 5
-
-
1.5 sec.
+
+
+
+
+
+
+
+
F Click to buy NOW!PDF-XChange Viewerwww.docu-track.comClick to buy NOW!PDF-XChange Viewerwww.docu-track.com D. LCD REMOTE CONTROL:
1. Press the F button the number of times corresponding to the Level you wish to select; the LCD will display LEVEL number (
) 2. Press the button while LEVEL number text is still on to perform the command. Button F x 1 Level 1 F x 2 Level 2 F x 3 Level 3 F x 4 Level 4 Tone / Vibrating Mode Vehicles Status Check /Alarm Report 1 sec. Button Beeper Button Lock Voltage Check LCD Backlight 5 sec./ 10 sec. /
Off Car 1 / Car 2 operation Temperature Check Remote Valet Power Save Mode Aux 5 Aux 1 Aux 2 Aux 3 Aux 6 Aux 4 Timer Start Daily Timer Start 24 hour repeat with cold starting Defogger Tone / Vibrating Mode: Press F button first then press button to enter Tone /
Vibrating Mode, Under this mode press button to select Tone Mode (
icon and text will display) or Vibrating Mode (
icon and text will display) or both (
&
icon and will display). Button Beeper: Press F button 2 times first then press button to enter Button Beeper Mode, Under this mode press button to turn on the button beep or turn off the button beep
. Button Lock Mode: Press F button 3 times first then press button to enter Button Lock Mode, Under this mode press button to select or
, the remote control will beep/vibrate 2 times and icon will display when a button is pressed indicating it is and locked. 6 Click to buy NOW!PDF-XChange Viewerwww.docu-track.comClick to buy NOW!PDF-XChange Viewerwww.docu-track.com Second Vehicle Security Operation: Press F button 4 times first then press button to enter Second Vehicle Security Mode, Under this mode press button to select CAR 2 operation (
icon and text will display) or CAR 1 operation and text will display. Vehicles Status Check /Alarm Report: Press F button 1 times first then press and buttons for 1 second until the beep confirms and then release the button. hold The LCD remote will display the current status of the vehicle.(Include trigger condition) Voltage Check: Press F button 2 times first then press and hold buttons for 1 second until the beep confirms and then release the button. The LCD remote will display the current voltage of the vehicle and text will display. LCD Backlight: Press F button 3 times first then press and hold button for 1.0 seconds until the beep confirms and then release the button to enter LCD Backlight time Mode, then keep press button to select LCD Backlight time
/
or
. Temperature Check: Press F button 4 times first then press and hold buttons for 1 second, until the beep confirms and then release the button. The LCD remote will display the current Temperature of the vehicle and text will display. Power Saver Mode: Press F button 2 times first then press buttons to enter Power Saver Mode, Under this mode press button to enable power saver mode and icon will display or disable power save mode and icon will display While in Power Save Mode the LCD remote will not look for any incoming signals from the main unit until a button is pressed. EXIT: Wait 10 seconds, or press the other buttons to leave the setting except the F button. 7 Click to buy NOW!PDF-XChange Viewerwww.docu-track.comClick to buy NOW!PDF-XChange Viewerwww.docu-track.com E. CHIRP INDICATORS PARKING LIGHT Chirp Function 1 Chirp 2 Chirps Arm Disarm Parking light 1 Flash 2 Flashes 3 Chirps Defective Reminder 3 Flashes Function Arm Disarm Disarm / Triggered Warning 4 Chirps Disarm / Triggered Warning 6 Chirps Car Finder 12 Flashes Car Finder Constant On Under Remote Start F. ALARM OPERATING CONDITION LED On Duty Arming Disarming Siren /
Horn 1 or 3 Chirps 2 or 4 Chirps Parking Light 1 Flash 2 or 3 Flashes Trigger Alarming Flashes Hidden Alarm Passive Arming Flashes LED Slow Flash Doors Starter Dome Light Locking Disable Turns on for 30-Second s Disable Flashes Disable Flashes OFF Unlocking Flash Pause Slow Flash Fast Flash Panic Alarming Flashes Car Finder 6 Chirps 12 Flashes Locking Flashes 8 Click to buy NOW!PDF-XChange Viewerwww.docu-track.comClick to buy NOW!PDF-XChange Viewerwww.docu-track.com G. ALARM DIAGNOTICS TABLE OF ZONE /
Situation Situation LED On Duty Zone 1 (Door Triggered) 1 flashes, break, then repeat Zone 2 (Trunk Triggered) 2 flashes, break, then repeat Zone 3 (Hood Triggered) 3 flashes, break, then repeat Zone 4 (Shock Triggered) 4 flashes, break, then repeat Zone 5 (Tilt Triggered) 5 flashes, break, then repeat Zone 6 (Ignition Triggered) 6 flashes, break, then repeat H. ACTIVE ARMING LOCK & ARM Press the button on the transmitter. The alarm arms, doors lock (if connected), and the siren chirps and parking lights flash once. The
+ ARMED icons, the text and beeps play to confirm. If Valet Mode* is ON, the
+
icons, the arm the alarm normally. text and tone play on the LCD transceiver. Exit Valet Mode to DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps and the defective
/
/
icon, text will display on the LCD screen, then you have left a door, trunk, or hood lid ajar. (See feature bank 1-06) SILENT ARMING: Press and hold the buttons for 1.0 second and the text t will display on the LCD screen. This will arm your security system. No chirp sound will be heard and the arm confirmation will be through the vehicles parking lights only. WARN-AWAY BY-PASS: Press button twice will arm the security system and bypass the warn-away and the warn-away icon will disappear and text and tone play on the LCD transceiver. Note: The bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle. Click to buy NOW!PDF-XChange Viewerwww.docu-track.comClick to buy NOW!PDF-XChange Viewerwww.docu-track.com Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.