FCC ID: H5OTR20 Car Alarm Transceiver

TRX950;XT90S PROFESSIONAL REMOTE CAR STARTER WITH ALARM SYSTEM 2-WAY LCD COMMUNICATION OPERATION MANUAL THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY

&

1 TABLE OF CONTENTS:

LCD REMOTE TRANSMITTER:

A. REMOTE TRANSMITTER OPERATION.4 B. BATTERY REPLACEMENT .... 5 C. THE REMOTE LCD ICONS WITH FUNCTION .........6 C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER ...7 1. Screen Lamp ON 2. Power Save Mode 3. Clear The Flash Icon and Melody Sound 4. Stop The Melody Sound. 5. Button Lock 6. Vibration / Melody Mode 7. Enable / Disable Bi Sound While Pressing Button:

8. Low Battery Indication. 9. Set Up Fixed Count Down Timer 10. Out Of The Range Check D.CLOCK & TIMER SETTING. .8 1. Timer Setting. 2. Alert Alarm Timer Setting 3. Count Down Timer Setting 4. Time Set-Up For Daily Timer Start A. REMOTE TRANSMITTER OPERATION .. 11 B. BUTTON LOCK .... 12 C. LED DISPLAY ........13 D. CHIRP INDICATOR ......... 13 E. PARKING LIGHT ...... 13 F. ALARM OPERATION CONDITION ....... 13 G. ACTIVE ARMING ARM & LOCK ....... 13 Defective Sensor Reminder Silent Arming / Disarming Shock Sensor By-Pass H. PASSIVE ARMING ... 14 Passive Arming with Passive Door Locking Passive Arming By-Pass I. ACTIVE DISARMING UNLOCK & DISARM ...14 Tamper Disarming Pathway Illumination Two Steps Door Unlock Automatic Re-Arm J. DISARMING WITHOUT A TRANSMITTER ...... 15 Overrides the Alarm without Password Pin Code Overrides the Alarm With Password Pin Code K. MODE .....16 Enter Valet Mode VALET 2 CAR PANIC Exit Valet Mode L. LOCATOR ......16 M. FUNCTION ........16 N. TRIGGER THE SYSTEM ...........17 Clear The Trigger Icons and Melody Sound Stop The Melody Sound Only Noise Abatement Circuit O. ANTI CAR- JACKING .....18 Active Anti Car Jacking Passive Anti Car Jacking Trigger The Anti Car Jacking Mode Override The System To Turn Off Anti Car Jacking P. SYSTEMS TRIGGER CHECK .........19 Q. SYSTEMS STATUS CHECK .......19 R.DRIVER PAGING (OPTION).......19 S. DOME LIGHT CONVENIENCE DELAY & SUPERVISION ...20 T. IGNITION CONTROL THE DOOR LOCK/UNLOCK. ...20 U. TRUNK RELEASE (CHANNEL 3) OUTPUT ...20 V. CHANNEL 4 TIMER CONTROL OUTPUT ..20 W. CHANNEL 5 TIMER CONTROL OUTPUT .... 20 X. CHANNEL 6 TIMER CONTROL OUTPUT ..... 20 Y. SECOND VEHICLE SECURITY OPERATION.21 Z. POWER ON MEMORY: ......... 21 REMOTE START OPERATION:

A. TO REMOTE START THE VEHICLE ....22 Safe Start (Child safety mode) B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START.22 C. TEMPORARY STOP FEATURE ........22 D. TURBO TIMER START FEATURE 23 E. TIMER / TEMPERATURE START .....23 3 Hours Timer Start With Temperature-Control Off 3 Hours Timer Start With Temperature-Control Daily Timer Start Exit the Timer Start F. TEMPERATURE CHECK ...... 24 G. TO TURN OFF THE REMOTE START ......24 H. SHUT-DOWN INPUT FOR REMOTE STARTER ........ 24 I. DISABLING THE REMOTE START SYSTEM ....... 25 WARRANTY PROVISSIONS.26 3 WARRANTY CARD..27 WARNINGS:

As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of childrens reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Alert servicing personnel that the vehicle can be started automatically. 4. Do not start the vehicle by remote while its in an enclosed area or garage. 5. Always apply the parking brake and lock the vehicle as you exit the vehicle. 6. The vehicle windows must be rolled up. 7. Should the unit malfunction, disconnect the fuse until the problem is corrected. 8. The use and operations of this system is the sole responsibility of the operator. 9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets. 10.Do not start the vehicle by remote while the standard transmission vehicle is parked at a steep place. LCD REMOTE CONTROL TRANSMITTER:

4 Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power or such Obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low out put powered frequency. A. BATTERY REPLACEMENT:

This transmitter uses one (1) 3-volt lithium ion battery (#CR2032) that is placed with the (+) side facing upward. To replace the battery, you will need to use a small flat blade screwdriver and a small Philips screwdriver. Remove the small Philips head screw. Then locate the small notch on the lower right side of the transmitter case next to the key ring. Using the flat blade screwdriver, carefully pry the top case from the bottom case. It should snap apart after breaking the seal. Before removing the battery note the direction of terminal. Place the new battery in exactly the same manner, being careful not to bend or damage the contact terminal. Snap the cases back together and then test the transmitter to insure it arms and disarms the alarm. Reinstall the Philips screw to finalize the battery replacement. the positive (+) 5 B. THE REMOTE LCD ICONS WITH FUNCTION:

Door Lock Your vehicle doors are locked Armed Mode Your vehicle is in armed mode Remote Transmission You are transmitting the signal to control unit Door Open Warning Doors are illegally opened (Zone 3) Shock Sensor Trigger Trigger on Shock Sensor (Zone 4) Door Unlock Your vehicle doors are unlocked and the system is Disarmed Valet Mode All the function shall be temporarily on hold. In Range Indicator Your are within the remote control range. Trunk/Hood Trigger Trunk or Hood is illegally opened (Zone 2) Warn Away trigger Trigger on Shock Sensor

(Zone 1) 6 Engine Starting Your vehicle engine starting by remote control Timer Control Start Start the Engine automatically at the same time next day or every 3-hour. Time Monitor Count Down Timer Reminder when time is up for parking Vibration Mode Remote Control vibrates when the system is triggered Driver paging Someone is paging you in front of your vehicle Engine Running Your vehicles engine is running Temperature Monitor Indoor temperature of your vehicle Alert Alarm You have set morning call alarm Power Save Mode Save the battery power Button Lock Disable the transmission function temporarily Low Battery You have to replace the battery of remote control. C: PROGRAMMING OF THE LCD REMOTE TRANSMITTER:

Transmitter Button

(1 second)

(3 seconds)

(5 seconds) Description LCD screen lamp turns on for 5 seconds. Timer Programming Mode. Power Save Mode

-

-

-

-

-

(2-second) Clear the Flash Icon and Melody Sound on the LCD Screen Transmitter Button Lock (

disable

) enable /

(2-second) Melody / Vibration (

)

(2-second) Mode Program Count Down Timer

) (10-Minute / 20M / 30

(

M /1Hour /1.5H / 2.0H) 7 Operation Press and hold for 1 second 1 melody sound to confirm enters. Press and hold for 3 seconds 2-melody sounds to confirm enter. Press and hold for 5 seconds 1 melody sound to confirm enters. Press within 3 seconds Press within 3 seconds Press within 3 seconds Within 3 seconds press the button until desired flashes time is set, then

-

(2-second) Enable / Disable Bi Sound

(Bi) While Pressing Button 1. Screen Lamp ON: Press and hold the melody sound and the LCD screen lamp will turns on for 5 seconds 2. Power Save Mode: While the power save mode, the LCD remote button one second, with one button for 5 seconds, with one icon on the LCD screen to indicate transmitter uses 0 current to save the battery power. Entry: 1. Press & hold the melody sound and entry the power save mode. 2. Under the Active Arming Mode and Disarm mode. Turn the ignition switch to on, the LCD remote transmitter will automatically entry the Power Save Mode Exit: Press any button of the LCD remote transmitter to exit the

Power Save Mode. 3. Clear the Flash Icon and Melody Sound: Press the within 3 seconds will clear the flash icon and melody sound on the LCD screen transmitter button 3 times 4. Stop The Trigger Melody Sound: While triggering the alarm the LCD screen will alert user through melody sound and flashing trigger icon, press any button on the LCD remote transmitter to stop melody sound only. 5. Button Lock: It is useful if you want to disable the transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by others. Press the button first, within 3 seconds press and hold

(

) button for 2 seconds to activate or cancel the the icon will displayed on the LCD button lock function, the screen to show the LCD remote transmitter is on Button Lock. 6. Vibration / Melody Mode:

It is useful when you are in a noisy place and difficult to hear beep sound from the remote control. The remote control in this mode will vibrate when your security system is triggered. Press the button first, within 3 seconds press and hold the

(

vibration or melody, the on the LCD screen to show the LCD remote transmitter is on vibration mode.

) button for 2 seconds to select the mode of icon will displayed 7. Enable / Disable Bi Sound While Pressing Button:

It has a short bi sound while pressing the button of the LCD screen 8 transmitter If you want mute the bi sound mute always while press button. Press the

(Bi) button for 2 button first, within 3 seconds press and hold the seconds to disable the bi sound. 8. Low Battery Indication:

When the power of the battery weakens, it has two short bi sound and flash icon while pressing the button of the LCD screen transmitter. 9. Set Up Fixed Count Down Timer:

1. Press the button for 2 seconds, the LCD screen will shows 2. Press the

(

button first, within 3 seconds press and hold the

(

) icon and timer (i.e. 0:10),

) button again showing next order time on the screen

(ie.0: 20), press them again (ie.0: 30)and so on. 3. Leave the buttons starting count down then icon flashes Note: 1.The count down period is fixed as 10 minutes, 20 minutes, 30 minutes, 1 hour, 1.5 hours and 2 hours maximum. a. When count down timer showing 0:00 means to turn off the timer. b. Press down. button for real time indication when the timer is counting 10. Out Of Range Indication:

1. If within the range, the icon will display on the LCD screen. icon will disappear on the LCD screen. Press Transmitter Button for and for for and for for and for for and for

+

+

+

+

for OFF and for ON for and for for and for

+

+

2. If you are out of range, the D. CLOCK & TIMER SETTING:

1 2 3 Transmitter Button Description Press & Hold the button until hour flashes Clock Setting (Hour)

*Flash digit for adjusting Press the once Press the once. Press the once Press the once Press the once Press the once button button button Time setting (Minute)

*Flash digit for adjusting Alert Alarm Time Setting

(Hour)

*Flash digit for adjusting Alert Alarm Time Setting

(Minute)

*Flash digit for adjusting button Alert Alarm Setting ON / OFF button button Count Down Timer Setting

(Hour)

*Flash digit for adjusting

(Max.19 hours 59 minutes) Count down Timer Setting

(Minute)

*Flash digit for adjusting 9 4 Press the once button Count down Timer Setting ON / OFF Daily Timer Start Timer for OFF and for ON Press & hold the button for 2 seconds. for and for

/

Setting Flash icon and Hours for adjusting button for 2 seconds or leave it for 10seconds,

+

EXIT: Press and hold the the system will exit the programming mode. 1. Clock Setting: Example to AM10:30 1. Press & hold the button for 3 seconds, with two-melody sound and the Hours digit flashes for adjusting. 2. Press the AM10:xx 3. Press the adjusting. 4. Press the until AM 10:30 or button to decrease or increase the Hour digit until button once again then the Minute digit flashes for or button to decrease or increase the Minutes digit 5. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode. 2. Alert Alarm Timer Setting: Example to PM 6:30 1. Press & hold the

Hours digit flashes for adjusting. 2. Press the digit is flashing for adjustment. button for 3 seconds, with two-melody sound and the button twice, the LCD screen will shows icon and Hours or button to decrease or increase the Hour digit until button once again then the Minutes digit flashes for or button to decrease or increase the Minutes digit until button once again then icon flashes for alert alarm ON /

button to start the Alert Alarm Timer, and the ON icon will button to stop the Alert Alarm Timer, show on the LCD screen. Press the and the OFF icon will show on the LCD screen. 8. Press timer program mode. button for 2 seconds with one-melody sound to confirm exit the 3. Press the PM 6:xx 4. Press the adjusting. 5. Press the PM 6:30 6. Press the OFF setting 7. Press the 10 or icon button to decrease or increase the Hour digit button 5 times, the LCD screen will shows button for 3 seconds, with two-melody sound 3. Count Down Timer Setting: Example Set count down timer at 2:30 1. Press & hold the and the Hours digit flashes for adjusting. 2. Press the and Hours digit is flashes for adjusting. 3.Press the until 2:xx 4.Press the adjusting. 5. Press the until 2:30 6. Press the alarm ON / OFF setting 7. Press the will show on the LCD screen. Press the will show on the LCD screen. 8. Press the confirm exit the timer program mode. button to start the count down timer, and the ON icon button once again then the Minutes digit flashes for button to stop the count down timer, and the OFF icon button to decrease or increase the Minute digit button for 2 seconds with one-melody sound to button once again then icon flashes for alert or Note: Maximum is 19 hours. 4. Time Set-Up For Daily Timer Start: Example to AM 6:30 1. Press & hold the button for 3 seconds, with two-melody sound and the Hours digit flashes for adjusting. 2. Press & hold the button for 2 seconds, the LCD screen will flash

/

icon and Hours digit for Hour set-up. 3. Press the or until AM 6:00 button to decrease or increase the hour digit 4. Press the 5. Press the or digit until AM 6:30 button once again then the minute digit flashes. button to decrease or increase the minutes 6. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode. OPERATION:

A. REMOTE TRANSMITTER OPERATION:

Transmitter System Function Remark 11 Button

-

+

+

-

-

-

+

+

+

(C)

-

-

-

-

-

-

-

Lock Doors & Arm System Panic function Car Locator Arm and Delete The 2 Stage Shock Sensor. Silent Arming / Disarming Active Anti Car-Jacking Mode Unlock Doors & Disarm System Two Steps Door Unlock &

Disarm System Trunk Release (Channel 3) Passive Arming By-pass Arm System and Hidden Alarm Function Activate or Turn Off The Remote Start Channel # 4 Timer Output (4) Channel # 5 Timer Output (5) Channel # 6 Timer Output (6) Press and Hold for 3 seconds. Under armed mode Press twice within 3 seconds Ignition in "off" position. Ignition in "on" position press and hold for 2 seconds Press twice within 3 seconds. Press and Hold for 2 seconds While the system Disarmed. Under disarm mode, press within 3 button seconds and Hold Press twice within 3 seconds. LCD DISPLAY TRANSMITTER OPERATION ONLY:

Transmitter Button

(C) System Function Systems Trigger Record Check Remark Press within 3 seconds

-

Systems Status Check Press within 3 seconds

(

) Button Lock Optional Driving Pager Press within 3 seconds and Hold button for 2 seconds Press within 3 seconds

(

)

(

(

)

)

-

Monitor Indoor Temperature Press within 3 seconds Daily Timer Start LCD screen lamp turns on for 5 seconds. Clear the Flash Icon and Melody Sound on the LCD Screen Transmitter Press within 3 seconds Press and hold for 1 second Press within 3 seconds Warning: Press the compartment is empty, then insert the new battery. button two times when the battery 12 B. BUTTON LOCK:

It is useful if you want to disable the transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by others. 1. The XT-85s Standard transmitter:

button first, within 3 seconds press and hold the Press the

) button for 2 seconds to activate or cancel the button lock function. The Red LED will pause flash for few seconds to indicate the remote control transmitter is on Button Lock mode when pressing the transmitter button.

(

button first, within 3 seconds press

(

) button for 2 seconds to activate 2. The 2-way LCD transmitter:

Press the and hold the or cancel the button lock function. icon will be displayed on the LCD screen to The confirm that the LCD remote transmitter is in the

Button Lock mode. C. LED display:

Function LED Disarmed Off Slow Flash Armed Flash Passive Starter Disable Fast Flash Passive Arming On (Solid) Valet Mode D. CHIRP INDICATORS:

Function Chirp 1 chirp Arm 2 chirps Disarm 3 chirps Defective Reminder 4 chirps Disarm / Triggered 6 chirps Car Locator F. ALARM OPERATING CONDITION:

13 LED 2 flashes... pause 3 flashes... pause 4 flashes... pause 5 flashes... pause Function Zone 1 / Warn-Away Trigger Zone 2 / Trigger on Trunk/Hood Zone 3 / Trigger on Door Switch Zone 4 / Trigger on Shock Sensor Zone 5 / Trigger on Ignition Switch E. PARKING LIGHT:

Parking light 1 flash 2 flashes 3 flashes Function Arm Disarm Disarm / Triggered 12 flashes Constant On Under Start Car Locator Remote Siren / Horn Parking 1. Arming 1 or 3 Chirps 1 Flash 2. Disarming 2 or 4 Chirps 2 or 3 Alarming 3. Trigger 4. Passive Starter Light Flashes Flashes LED Slow Flash Slow Flash Fast Flash Flashes Flashes 12 Flashes Disable 5. Panic Alarming 6. Car-Jacking Alarming 7. Car Locator 6 Chirps G. ACTIVE ARMING LOCK & ARM:

Doors Starter Dome Light Locking Disable Unlocking Turns on for 30

-second Disable Flashes Disable Locking Flashes Disable Flashes button on the transmitter. 1. Press 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle door will lock upon arming when interfaced with the security system. System Arm Door Ajar Trunk / Hood Ajar Clear The Flash Icon:

Press the times within 3 seconds will clear the flash icon on the LCD screen transmitter. button 3 and DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you have left a door, trunk, or hoodlid ajar. SILENT ARMING / DISARMING: Press the transmitter button at the same time will arm or disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only. SHOCK SENSOR BY-PASS: Press the button on the transmitter two times within 3 seconds will arm the security system and by-pass the shock sensor. The system will chirp one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle. H. PASSIVE ARMING Active arming / disarming is controlling your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows. 1. Turn the ignition to the OFF position and exit the vehicle. 14 2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle entrances are closed. 3. After 30-second timer has elapsed, the security system will automatically

ARM. The siren will chirp [1] time and the parking lights will flash [1] time. PASSIVE ARMING WITH PASSIVE DOOR LOCKING:

The vehicle doors will automatically lock after passive arming cycle has been completed. PASSIVE ARMING BY-PASS: While the system is disarmed, Press the buttons twice, the system will respond with [1] chirp and LED will turn ON. The security system will remain in this temporary state for as long as you button and the wish. To exit passive by-pass, press the transmitter system will return to normal status. or I. ACTIVE DISARMING UNLOCK & DISARM:

button on the transmitter. 1. Press 2. The siren will chirp twice and parking light flash twice to indicating that the security system is now disarmed. The vehicles door will unlock and dome light turns on for 30 seconds upon disarming when interfaced with the security system. System Disarm Doors Trigger Trunk/HoodTrgr Warn away Trigger Shock SensorTrgr Ignition Trigger Clear The Flash Icon:

Press the button 3 times within 3 seconds will clear the flash icon on the LCD screen transmitter. TAMPER DISARMING: If alarm is triggered upon disarm, the systems siren will chirp 4 times, and parking light flash 3 times. PATHWAY ILLUMINATION: This feature turns the parking light ON for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal. TWO STEPS DOOR UNLOCK:

This feature will independently unlock the drivers door only when disarming the button a second time within 3 seconds will security system. Pushing the unlock the other doors. 15 sound.) AUTOMATIC RE-ARM:

If this feature is selected, the security system will automatically re-arm itself in 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed. J. DISARMING WITHOUT A TRANSMITTER OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE:

(Factory Default Setting) The Override function may be used if the remote transmitter is lost or inoperative. 1. Enter the vehicle and turn the ignition switch to ON position. 2. (Alarm will sound.) 3. Within 10 seconds push and release the valet switch, The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally. OVERRIDE THE ALARM WITH PASSWORD PIN CODE:

Unlike valet switch easily found, and defeated, this security system allows the consumer to program a password pin code. Offering a higher level of security. 1. Enter the vehicle and turn the ignition switch to ON position. (Alarm will 2. Within 5 seconds, enter your chosen the first digit code by pressing and releasing the Valet Switch. (When finished above procedures, systems siren stop alarming, lights stop flashing, but the vehicle cant be started.) 3. Within 15 seconds of the last digit code enter (the 1st code), turn the Ignition 4. Within 15 seconds, enter your chosen of the second digit code by pressing Switch OFF and then ON. and releasing the Valet Switch. 5. Turn the ignition switch OFF position. 4] Chirps form siren/horn, [3] flash from parking light to indicate the system was disarmed. Note 1: You must override the alarm within 60 seconds. If not, the system will automatically re-arm. EXAMPLE: To Override The System With The Password Code 83, 1. Enter the vehicle and turn the ignition switch to ON position.

(Alarm will sound.) 2. Within 5 seconds, Press and Release the Valet Switch 8 times, (When finished above procedures, systems siren stops alarming, lights stop flashing, and sensor stops trigger, but the vehicle can not be started or driven away.) 3. Within 15 seconds of the last digit code enter (the 1st code), turn the Ignition Switch Off and then ON. 4. Within 15 seconds, Press and Release the Valet Switch 3 times 5. Turn the Ignition Switch to Off position. [4] Chirps form siren/horn, [3] flash from parking light to indicate the system was disarmed. K. VALET MODE: (System in Disarm or Valet mode) The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions and remote start functions are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed either by using your remote transmitter, or by operating the Manual override sequence. 16 Remote Door Lock Remote Door Unlock Enter Valet Mode:

1. From the disarmed condition, turn the ignition to ON position. 2. Push and hold valet switch for 2 seconds until the LED turns on. The LED wills remain on as long as the system is in valet mode. Exit Valet Mode:

1. Return to normal operation, turn ignition on. 2. Push and hold valet switch for 2 seconds, The LED will turn off indicating the system is exiting the valet mode. L. CAR LOCATOR Under armed mode, press the button to active car locator function. The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car. M. PANIC FUNCTION:

The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency. 1. Press and hold the button for 3 second. The alarm will immediately sound. 2. During panic mode, the normal function of this buttons can be used to lock and unlock the transmitter button will be disabled. The transmitter and door (if the option is installed), however once the button is pressed, the vehicles starter disable device,

(where installed) will be disengaged allowing the vehicle to start. 3. To stop the alarm, press and hold the transmitter button on the button is pressed and released, the panic mode will be turned off transmitter again for 3 seconds. Also if any transmitter button other than or immediately. 4. If the button is not pressed, the alarm will automatically stop after 30 or seconds. N. TRIGGER THE SYSTEM When armed, your vehicle is protected as follows:

1. Light impact will trigger the warn-away signal. 2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition key will trigger the programmed sequence. The starter disable relay (if installed) prevents the vehicles starter from cranking. The siren, horn, parking lights, and dome light will turn on to alerting 17 of an intrusion for 30 seconds. Then it will stop and automatic reset and re-arm. If the one of sensors or detectors still active, the alarm system will sound a maximum of 3 times of 30 seconds cycles. Door Trigger Trunk/Hood Trigger Warn-away Trigger Shock Sensor Trigger Ignition Trigger CLEAR THE FLASH ICON AND MELODY SOUND: While triggering the alarm the LCD screen will alert user through melody sound and flashing trigger icon, press the button 3 times within 3 seconds will clear the flash icon and stop melody sound on the LCD screen transmitter. STOP THE MELODY SOUND ONLY: While triggering the alarm the LCD screen will alert user through melody sound and flashing trigger icon, press any button on the LCD remote transmitter to stop melody sound only NOISE ABATEMENT CIRCUIT: You system has Noise Abatement Circuit. It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder, jackhammers airport noise, etc. Heres how Noise Abatement Circuit works: The alarm triggers 3 times. Each time, the same sensor or switch is triggering the alarm. Noise Abatement Circuit will interpret this pattern of triggers as false alarm. After the third trigger,

Noise Abatement Circuit ignores, or bypasses, that sensor or switch until the other sensor or switch is trigger.

Noise Abatement Circuit covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door for three full cycles, the doors will be bypassed until the trigger ceases. O. ANTI CAR- JACKING Warning: If you dont need the car jacking function in this alarm system, be sure to set car jacking feature OFF. This system is default setting all car-jacking OFF. ACTIVE ANTI CAR JACKING:

1. Press and hold the transmitter button at the same time for 2 and seconds while the vehicles ignition is ON. The parking lights will turns on for 1.5 seconds to indicate this enter. 2. Once the system is armed, If you are forced from the vehicle, the system will trigger when the door is opened and closed while the ignition is ON. PASSIVE ANTI CAR- JACKING:

It operate as below:

1. Turn the ignition switch to the ON position; the system will arm. 2. Once the system is armed, If you are forced from the vehicle, the system will trigger when the door is opened and closed while the ignition is ON. TRIGGER THE ANTI CAR -JACKING MODE:

3-timer circuits will function as follows:

First timer:

18 a. 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds. b. During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off the car-jacking feature. If not, it will enter second timer car jacking. c. 65 seconds after the system has been triggered. The siren starts alarming and the parking light starts flashing. Second timer:

Third timer:

90 seconds after the system has been triggered a. The siren still alarming and the parking light flashing, and b. The starter disable will activate to prevent the vehicle from starting. c. It will remain active until the vehicles battery power exhausted. OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:

Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the system disarmed Note: If you use password pin code to double protect the vehicle security, you will need to use it to completely disarm the system. P. SYSTEMS TRIGGER CHECK Press the transmitter first, within 3 seconds press

(C) button. It responds with one melody sound and all triggers records will immediately displayed on the LCD screen. Q. SYSTEMS STATUS CHECK When you want to check the systems present status through the LCD screen, Press the transmitter

(C) button. button twice, within 3 seconds press It responds with one melody sound. R. DRIVER PAGING In Car Driver Paging It is useful the event that someone wants to page the driver of the parked vehicle. Under the ignition switch off condition, press and hold the valet switch for 2 seconds to page the driver, one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD Transmitter and Out of Car Driver Paging

indication flashes on the LCD screen. 19 If someone tries to page you by tapping the paging (knock) sensor (optional) which is usually mounted on the bottom part of front window, the paging melody sound continues sounding from you Remote LCD Transmitter and

1. Press the transmitter

indication flashes on the LCD screen. button first, within 3 seconds press

) button to activate outdoor driver paging function, It responds with chirps of the

" indication flashes vehicle, a melody sound and "

on the LCD screen to confirm the function is on.

(

2. When tapping the paging (knock) sensor, one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD Transmitter and

indication flashes on the LCD screen. 3.Turn on the ignition switch; OR press the arm the system; OR press the button to disarm the system, this outdoor driver paging function will exit. button to S. DOME LIGHT CONVENIENCE DELAY & SUPERVISION The alarm with a unique feature which will turn on your vehicle dome light as following:

1. Upon disarming, the interior light will remain on for 30 seconds. 2. If the vehicle is intruded, the interior light will flash for the same duration as the siren. Note: Turn on the ignition switch or arm the alarm will turn off the dome light. T. IGNITION CONTROL DOOR LOCK/UNLOCK. If the vehicles door locks have been interfaced to the security system, the system will automatically lock the vehicles doors when the ignition is turned

ON and /or unlock the vehicles doors when the ignition is turned OFF. U. TRUNK RELEASE (CHANNEL 3) OUTPUT. Press and hold button on the transmitter for two seconds to remote control the trunk release or other electric devices. V. CHANNEL 4 TIMER CONTROL OUTPUT 20

(5) and

(4) and

(4) button at the Press the transmitter same time to active Channel 4 function. Channel 4 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlight, power window or sunroof. (Factory defaults setting at momentary output.) W. CHANNEL 5 TIMER CONTROL OUTPUT

(5) buttons at the Press the transmitter same time to active Channel 5 function. Channel 5 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlight, power window or sunroof. (Factory defaults setting at momentary output.) X. CHANNEL 6 TIMER CONTROL OUTPUT

(6) buttons at the Press the transmitter same time to active Channel 6 function. Channel 6 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlight, power window or sunroof.

(Factory defaults setting at momentary output.) Y. SECOND VEHICLE SECURITY OPERATION:

(6) and Your 5-button remote transmitter can be utilized to control a second vehicle security system, To program the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming. Programming the Transmitter to 2nd Car Enter:

1. Turn the ignition key ON 3 times. (Finishing in the ON position) 2. Press valet switch 2 times, holding in on the 2nd push, you will hear a long siren chirp. (Release the valet switch) 3. Press the shift button of the Car 2 transmitter.

** LCD transmitter must be put in 2nd car mode to program for 2nd car.

(See next page) 4. Press the lock button on the transmitter; you will hear 1 siren chirp. Turn OFF the ignition switch; you will hear 3 long siren chirps to confirm programming and exit transmitter programming

** For 2-way LCD Display Transmitter:

2nd Car Operation:

21 1. Press first, within 3 seconds press and hold and buttons at the same time for 2 seconds. Two beeping sound

icon will be displayed on the LCD screen to and the indicate the second transceiver pin code is programmed. 2. While the

icon is displayed on the LCD screen, you can remote control and communicate with a second vehicle security system. It has two short bi sounds while pressing the button of the LCD screen transceiver. Back to 1st Car Operation:

1. Press first, within 3 seconds press and hold and buttons at the same time for 2 seconds. One long beeping

timer icon will be displayed on the sound and the LCD screen indicating the system is back to the first transceiver pin code. 2. While the

timer icon is displayed on the LCD screen, you can remote control and communicate with the first vehicle security system. It has one short bi sound while pressing the button of the LCD screen transceiver. Z. POWER ON MEMORY:

This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected

. A. TO REMOTE START THE VEHICLE:

REMOTE START OPERATION:

22 button once on the transmitter. When you want to start your vehicle, 1. Press 2. The parking light will activate to indicate the remote start received the signal. 3. The engine will start approximately 5 seconds. 4. Once the engine is running, after couple seconds the parking light will turn on again and climate controls will activate and adjust the vehicles interior temperature to your preset setting. (While the vehicle is running, the minutes digit on the LCD screen will flash and the will indicate count down timer based on the 5, 10, 20 or 30 minute run time set up by your installation center.) 5. The vehicle will run for 5 to 30 minute cycle automatically shut down. (When the unit shuts off the count down timer will turn off and the transmitter will play a melody.) E: The Remote Start Unit will not start the vehicle if any one of the following conditions exists:

1. The hood is opened. 2. The brake pedal is pressed. 3. Move the optional remote start enable toggle switch to OFF position. (If installed) 4. The gear selector is in any gear other then PARK or

NEUTRAL SAFE START (Child safety mode) Activate Remote Start Engine Running button twice on the transmitter to start Factory defaults setting to press the the vehicle. Programming this feature to eliminate an accidental remote start, 1. The user presses the transmitter start the vehicle. or 2. The user presses the transmitter start the vehicle. buttons twice within 3 seconds to buttons at the same time to and B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START:

To operate the vehicle while the engine is running on the remote start, 1. Insert the ignition key and turn it to ON (not the start) position. 2. Press the brake pedal. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. C. TEMPORARY STOP FEATURE:

This feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate control on. 1.Before turning off the engine, press the button twice on the transmitter and the LED indicator will flash 3 times to confirm enter. 2.Turn the ignition key to OFF position. (The engine will stay running.) 3.The engine will run until the pre-programmed time elapsed or shutdown input is received. D: TURBO CHARGE MODE:

23 Turbo charge mode keeps the engine running after arriving at your destination for a programmable period of 1, 3 or 5 minutes, This allows the vehicles engine time to conveniently cool down the turbo after you have left the vehicle. To activate:

1. While the engine is running, pull up the hand brake and place the transmission gear in the park position. 2. Before turning off the engine, press and release and buttons at the same time.

-- The LED will flash indicating the remote start has entered the turbo charge mode. 3. Take the Ignition Key from the key cylinder.

-- Engine keeps running. --

4. Exit and secure the vehicle.

-- Engine continues running until the pre-programmed time elapsed. --

NOTE: This feature only applies to vehicles with Turbo Engines. E. TIMER / TEMPERATURE START:

This unit can be programmed to start and run the engine every 3 hours or punctually at the same time next morning, the engine will run for the programmed running time and then shut down. IMPORTANT: Timer Start should be used only in open areas, never start and run the vehicle in on enclosed space such as a garage or carport. 3 hours timer start with Temperature-control OFF: This feature is design for an extreme cold climate usage. The system will auto start the vehicle every 3 hours, to prevent engine freezing and hard to start. A MAXIMUM OF SIX CYCLES CAN OCCUR. 3 hours timer start with Temperature-control:

If you installed the optional Temperature Sensor and programmed the temperature ON to operate. The system can be programmed to automatically start the vehicle engine whenever the temperature inside the vehicle reaches or drops below the preprogrammed temperature level. The system will monitor the air temperature every 3 hour and will only start the engine during extreme cold temperatures. There are three temperature levels to choose from. Daily Timer Start: The feature is very useful for the driver who wants to run the vehicle punctually at the same time next morning. Before set-up of the

Daily Timer Start, you should set you time for engine start.( see Timer Setting

/ Timer set-up for Daily Timer Start, page 16) ENTER:

1. Press the 2. Immediately depress the 3-a. 3 Hours Timer Start: Rapidly depresses the button once to remote start the vehicle. button once, within 2 seconds

+

buttons = Start / Stop button.) The parking light will flash (3) times. The siren or horn chirps (3) times. The vehicle is now programmed to start every (3) hours. buttons, if you program +

button (or depresses 24 3-b. Daily Timer Start: Depress the transmitter button first, button for two seconds. within 3 seconds press and hold The parking light will flash (6) times. The siren chirps (6) times. The vehicle is now programmed to start at the real time of the next day. Your set time for the next day engine start flashes for approx. 3 seconds on the LCD screen. After 3 seconds the icon stays displayed on the LCD screen. 4. Press the brake pedal to stop the vehicle running. Exit the timer start: Timer start can be exited manually as follows:

1. Make sure the remote start system is not operating the engine. 2. Turn the ignition on. The LED and parking light will flash (4) times. The horn chirps (4) times. Or F. TEMPERATURE CHECK (OPTIONAL) If you installed the optional temperature sensor, you can monitor, through the LCD screen, the present indoor temperature of the passenger compartment before cooling or heating your vehicle. Press the transmitter buttons first, within 3 seconds press the

) button, the in-door temperature will be shown on the LCD than actual ambient screen. This temperature due to the greenhouse and is relative only the inside vehicle temperature. reading may be higher

(

G. TO TURN OFF THE REMOTE START:

When the engine is running (by remote start), if you want to stop it, 1. Press mode. button once on the remote transmitter under remote start 2. Move the optional remote start enable toggle switch to OFF position. (If installed) 3. Press the brake pedal The vehicle will shut down and turn off the parking light to indicate engine stopped H. SHUT-DOWN INPUT FOR REMOTE STARTER:

If any of the following conditions exist while the system is operating, the engine will not start or will shut down immediately:

1. The hood is opened. 2. The brake pedal is pressed. 3. Engine is over-revved. {Tachometer checking type only}

4. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed. 5. Press 6. Move the optional remote start enable toggle switch to OFF position. (If button once on the remote transmitter under remote start mode. installed) 7. The vehicle refused to start running after {3} unsuccessful attempts. I. DISABLING THE REMOTE START SYSTEM: (If installed) 25 This feature allows your systems remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the OFF position. LIMITED LIFETIME WARRANTY PROVISIONS 26

( U.S. ,Continental U.S. and Canada Only) 1. Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery. Your Auto Page equipment is guaranteed for life to the original purchaser/user of the equipment and the original vehicle in which it was installed by an authorized installer under the following conditions: If the product proves defective (according to Auto Pages testing) within the first year, the defective unit may be exchanged or repaired free of charge. Proof of Purchase (dated sales receipt) must accompany all warranty returns;

otherwise, your return will be rejected and sent back. After one (1) year, the purchaser should ship the unit prepaid to Auto Page with a money order in the amount of $30.00 to cover shipping and handling charges. Note: The enclosed Warranty Card may be required to receive warranty services. 2. This WARRANTY will be considered void if the equipment has been misused, neglected, improperly serviced or installed, altered, dropped or damaged by water, contrary to the Auto Page OPERATIONS MANUAL. Or, if used with accessories not approved by Auto Page, which may have contributed to the defect. See note below regarding product installation**. 3. The purchasers remedies under this WARRANTY shall be limited to the repair or replacement of electronic components only. THE FOLLOWING IS NOT COVERED: Damages or deterioration to cases, batteries, covers and cabinets; the cost of repairs, replacement and labor of which shall be borne by the purchaser even if occurring during the WARRANTY period. 4. Any equipment or parts which are claimed to be defective under this WARRANTY must be sent to the Auto Page Service center with proof of purchase at the purchasers expense prior to such return, a Return Authorization Number should be obtained. Auto Page will return the equipment, charges prepaid. Warranty Service can be provided through the dealer where the equipment is originally purchased. 5. Any unexpired WARRANTY shall be applicable to equipment and parts in the possession of the original purchaser only. 6. THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IMPLIED, 7. Auto Page shall not be liable, under the foregoing WARRANTIES or otherwise, for: Any personal injury of any kind to the purchaser, its employees or agents or anyone else whomsoever resulting directly or indirectly from the use or presence of the equipment or parts;

Consequential damages of any kind; any inability of the purchaser to use the equipment. The attached WARRANTY CARD is for your record. However, Auto Page reserves the right to request you to submit this WARRANTY CARD, which must have complete information to receive warranty service. Please keep this card in a secured place.

**IMPORTANT NOTE: Any damages to the alarm system resulting from an installation performed by anyone other than a professional installation technician authorized by a dealer of Auto Page will void the products limited lifetime warranty. This WARRANTY CARD is for your record. However, Autopage reserves the right to request you to submit this WARRANTY CARD, which must have complete information to receive warranty service. Please keep this card in a secured place. 27 Company Name Dealers Address DEALER TO COMPLETE AUTOPAGE WARRANTY SERVICE CARD Model: _______________ Serial # _______________ CUSTOMER TO COMPLETE Mr./Mrs./Ms. ___________________________ ________________________________ Your Name (Please Print) ___________________________ ________________________________ Address ___________________________ ________________________________ City, State, Zip Code ___________________________ ________________________________ Telephone Number ___________________________ ________________________________ Year / Make / Model of Vehicle Date of Installation / Purchase

Proof of Purchase which includes the store name and date of purchase must accompany all warranty returns. It is the purchasers responsibility to keep this card for any future warranty service. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference ________________________________ Dealers Telephone Number City, State, Zip Code Dealers Signature that may cause undesired operation. Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. 28 960 Knox Street Unit B Torrance, California 90502 Main Office: 310-323-1800 Customer Service: 800-262-2527 Ext. 462 www.autopageusa.com 29