FCC ID: VMUAVE-TPMS-T100C TPMS

Installation and Operating Instructions Advanced Vehicle Electronic Technologies Co. Ltd FCC ID : VMUAVE-TPMS-T100C Advanced Vehicle Electronic Technology Co., Ltd. B-2, 23F-2, No.29, Haibian Road, Lingya District, Kaohsiung 802, Taiwan Website: www.avetechnology.com Phone: 886-07-3310885 886-07-3311351 Fax:

sales@avetecnology.com E-mail:

1. AVE Tire Pressure Monitoring System (TPMS) 2 TABLE OF CONTENTS 2. Notice 2 3. Caution 3 4. Specifications of AVE TPMS 4 5. AVE TPMS Components 5 6. System Setup 6 7. Tire Sensors Installation 7 8. Display Unit Introduction 10 9. Operating AVE TPMS 9-1. Operating Mode 12 9-2. Function Mode (To review every tires condition quickly) 12 9-3. Unit Mode (To review every tires condition quickly). 13 9-4. Pressure setup mode (To change vehicle mode & pressure) 14 9-5. Setup the 2nd Standard Pressure .. 16 9-6. Match Tires and the 1st or 2nd Standard Pressure.. 16 9-7. Mount/Dismount the Trailer 16 9-8. Tire setup mode (To change/rotate tires) . 17 9-9. Set up sensor position .. 18 9-10. Reacting to Alerts ... 19 10. LF Remote Control ..... 22 11. Chart of Tire Setup Mode and Leak Test 23 12. AVE TPMS Extended Antenna Cable .. 24 13. AVE TPMS Optional Accessories 25 14. Appendixes 26 15. Warranty 27 1 www.avetechnology.com 1. AVE Tire Pressure Monitoring System (TPMS) Thank you for purchasing AVEs Tire Pressure Monitoring System (TPMS). AVEs TPMS was designed to provide you with extra protection while driving. Our TPMS informs you of tire pressure and tire temperature and immediately notifies you of any problems such as a slow or fast leak. After proper installation, AVEs TPMS will continually monitor your vehicles tire pressure and temperature with accurate and up-to-date information. If the TPMS detects any irregularity in the tires pressure and/or temperature, it will immediately sound an alarm and flash on the LCD display to notify the driver. Prompt action needs to be taken to avoid accidents and ensure the safety of the driver and their passenger. 2. Notice FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B devices, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference. This equipment can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a correct installation. If this equipment does cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the factoring measures. Reorient or relocate the receiving antenna Change the place and connection way of receiver. Increase the separation between the equipment the system Attention Any changes or modifications in construction of this device could void the users authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, this devices antenna must not be co-located or operating to conjunction with any other antenna or transmitter. 2 www.avetechnology.com 3. CAUTION AVEs TPMS system is designed to monitor the tires condition and alert the user if there is any irregularity detected. Use of chemical sealants for temporary resealing or re-inflation in tire assembly may affect or even damage the sensors function. For your own safety, please read and understand the instruction manual before proceeding to the installation and setup. Please seek qualified personnel for proper tire sensor installation. Only use the power cord cigarette adapter supplied by AVE Technology. Do not use AVE Technologies power cord in any other USB device. It is NOT USB compatible and may damage your USB device. AVE TECHNOLOGY shall not be held responsible for any damage caused to any USB device if you use this power adaptor in any other device. When you unplug the power adaptor, do not pull from the cord. It may damage the adaptor. If the power cable is damaged in any way, and is under warranty, contact your dealer. Never try to disassemble or repair the product yourself. 3 www.avetechnology.com 4. Specifications of AVE TPMS Sensors/Transmitter Specifications Battery life Battery voltage Storage Temperature Operating Temperature Temperature Resolution Pressure range Pressure Resolution Operating Humidity Operating Frequency Receiver Specifications Estimated 5 to 7 years

(under normal operating condition) 3 V

-55C to 125C

-40C to 125C 3C 700kPa(Car ), 1400kPa(Truck) 2.66kPa(Car), 5.5kPa(Truck) 100%

434 MHz Operating Voltage Operating Temperature Monitored Temperature 9V to 18V

-20C to 85C

-40C to100C 4 www.avetechnology.com 5. AVE TPMS Components ITEM A B C C1 D E F G H Accessory Display Unit Tire Sensors Power cord cigarette adapter Hard wire kit Common metal valve Air conditioner clip User manual or CD Base Adhesive Remote Control Quantity 1 4 1 Optional 4 2 1 1 Optional 5 www.avetechnology.com 6. System Setup Process Connect the Mini USB End of the Power Adaptor to the display unit. Attach the antenna by gently screwing it on clockwise, finger tight. Step 1 2 3 4 5 Install the display unit into the desired location. Install the air-vent clips for vent mounting. Apply the enclosed double sided adhesive cushion to the base of the Display Unit for dashboard mounting. Plug in the Cigarette Adapter to vehicles cigarette lighter socket. Note: It must be a 12 V power supply!

For OE power cable, connect different wires according to the label. Connect Ground, IGN, BATTERY (12V), while ANTENNA wire does not need to be connected. Please refer to the appendix chart. AVE TPMS display unit setup is now complete. Please start the engine or turn the key to IGN position. AVE TPMS display unit will start receiving signals from tire sensors only if the tire sensor has been installed and after the tire is inflated. Please proceed to Tire Sensor Installation on page 5. Note: There is no need to set the tire position on the TPMS Unit. It has been pre-set at the factory. It is important to install the tire according to the tire position on the sensors label.

(Vehicle with four wheels: front left, front right, rear right, rear left. To set up a vehicle with more than 4 wheels, please set up tire location in accordance with page 13.) 6 Photo www.avetechnology.com 7. Tire Sensor Installation

*Screw the 2 nuts one by one. After you screw the first nut, try to move the valve to see if it's still, then the next one. And make sure they are all on the thread. Step Process Photo Remove tire from the vehicle. Deflate the tire and remove the tire from the rim. Seek assistance from qualified personnel if necessary. Each sensor has a small label attached showing the wheel position it needs to be;

Front Left (1) Front Right (2) I Rear Left (3) Rear Right (4)

(Vehicles with more than 4 wheels please set up in accordance with page 13) Install the sensor inside the wheel. MAKE SURE the tire sensor is installed into the intended tire. (Front right, Rear Left etc.) Note: AVE TPMS uses a common metal valve. If necessary, it is easy to change the valve at any tire shop. Do not hit the tire sensor when the wheel is taken apart!

1 2 3 7 www.avetechnology.com 4 5 6 7 8 Be sure the rubber seal is properly positioned between the rim and the valve. Clean the inside of the tire from any dust and inflate the tire to the proper pressure as recommended by the tire manufacturer. The tire must be inflated to the proper tire pressure to activate the tire sensor. Pressure unit kpa 260 560 psi 37.7 81.2 bar 2.6 5.6 700Kpa 1400Kpa Tires MUST be balanced after the tire sensor has been properly installed. Tires must be balanced by professional personnel. Be sure to install the tire into the proper location as per the tire sensor. If you fail to do this, the TPMS unit will give you readings from the wrong location. Follow the above procedure for the other 3 tires. Once the tire sensors have been properly installed, connect the display unit to vehicles cigarette lighter power. AVE TPMS will then detect signals from the tire sensors. If there is no signal, disconnect the power to the display unit, re-connect it and try again. If there is still no display, try a third time. If after the third try you still have no signal please reset the display unit.

(Please refer to Tire Setup Mode on page 19) Note: There is no need to setup up the tire location as it is preset at the factory. (This is only applicable if the tire installation is according to the position on the sensors label.) 8 www.avetechnology.com Anti-theft installation of external sensor 1. (LeftRight) Anti-theft nut, Original metal valve on car, External sensor 2. Take off the cap of valve, and screw the nut on valve 3. Install the external sensor on valve by hand, and use wrench to screw the nut opposite way up, until you cant easily take off the cap by hand. Please avoid using any other tool to touch the external sensor, in order not to destroy the structure. Notice:

You can soap liquid test after installation to make sure they don't leak. (A complete external sensor is water-proof outside) 9 www.avetechnology.com No. 1 2 3 8. Display Unit Introduction Description Sensor battery icon Measures the Tire Sensor battery level Signal strength icon Measures the signal strength from the tires sensor. Vehicle battery reading Monitors the vehicles battery (in operating mode)

(If it is above 15.5V or below 11.5V, it will flash and has a warning sound) Photo 10 www.avetechnology.com 4 5 6 7 8 9 Pressure Warning icon Will light when the Tire Sensor detects any irregularities in Tire Pressure . i.e.:. Fast/Slow leak, tire pressure above or below 30% of recommended pressure Flat tire icon Will light when flat tire is detected. High Temperature Icon Will light when the temperature inside the tire is above 85C (185F) Wheel types (car or truck mode) Up to 8 modes of vehicle type selection Programmable up to 27 tires. Optional monitoring for spare tire. Pressure Meter Measures 3 different pressure units (KPa, bar, psi) Color difference to differentiate between normal

(Green) and warning (Red) Displays actual pressure value on display unit. Note:

Before receiving the signal, it shows last recorded pressure. Temperature Meter Measures degrees Celsius (C) or Fahrenheit (F) Different colours to differentiate between normal

(green) and high temperature (red) Displays actual temperature value on the display unit. Note:

Before receiving the signal, it shows last recorded temperature. 11 www.avetechnology.com 9. Operating AVE TPMS 9-1. OPERATING MODE AVE TPMS display unit will monitor each tire for 10 seconds and then proceed to the next tire. Problematic tire will be monitored for 15 seconds before proceeding to the next tire. It will keep displaying the warning code until the problem has been taken care of by the user. For the alerts/warnings codes, please refer to the Reacting to Alerts section. The tire being monitored will light and its information will be displayed.

( i.e.: pressure, temperature, tire sensor battery level and signal strength) Note: User has the option to turn off the beeping sound by pressing button. 9-2. FUNCTION MODE (To review every tires condition quickly) Press MODE. button once to enter FUNCTION Message area will display FUN. Press Press To exit, do not touch the display unit for 20 seconds. for previous tire selection. for next tire selection. Note: If there is 20 seconds or more of inactivity, the system will quit the FUNCTION MODE and return to OPERATING MODE. 12 www.avetechnology.com 9-3. UNIT MODE (To change pressure or temperature unit) Press and hold enter UNIT MODE. button for 3 seconds to 1) The message area displays P 2) Psi icon will light (the default pressure unit or the previously selected unit). 3) Press

( psi kpa bar psi ) to change pressure unit. Note:

If Truck pressure is above 999 kpa, you can only select psi or bar Unit 4) Continue to press selection. for pressure unit 5) Press to confirm the selection. Pressure unit is then saved. Note:

To bypass pressure unit change, skip step (3) & (4). Go to step (5) to confirm the default unit settings. The default pressure unit is in psi or previously selected unit of measure. To exit Unit Mode, do not touch any buttons for 20 seconds. Changes will not be saved (before step 5) and the system will use the default pressure unit. 6) Immediately after step (5), message area will display T. 7) C icon will light (default temperature unit or previously selected unit). 8) Press

( C F C ) to change temperature unit. 9) Continue to press unit selection. for temperature 10) Press to confirm the selection. Temperature unit is then saved. 11) UNIT MODE setup is now complete. System will automatically return to OPERATING MODE. Note:

To bypass temperature unit change, skip step (8) & (9). Go to step (10) to confirm the default unit settings. Default temperature unit is in Celsius or previously selected unit To exit, do not touch any buttons for 20 seconds. Changes will not be saved (before step 10) and the system will use the default temperature unit. 13 www.avetechnology.com 9-4. PRESSURE SETUP MODE (To change vehicle mode & pressure) Press and hold PRESSURE SETUP MODE. 1) The message area will display M01 (The default button for 3 seconds to enter vehicle mode) or the previously selected mode. 2) Press to change vehicle mode. ( M01 to M02 ~ M08 M01 ) Or press keep the default or the previously selected vehicle mode. Then the system will allow you to setup the 2nd standard tire pressure. (Please refer to page 15.) 20 seconds or more of inactivity at this step will exit the setting and get back to the operation mode. Change will not be launched. 3) Press to confirm and save the selection of vehicle mode. Immediately after this step, the message area will display the default pressure value. (Default pressure value depends on the vehicle mode selection.) Follow step 4 to confirm or set the standard pressure value. This step will erase the previously selected vehicle mode and pressure. Moreover, the display will also lose every sensors ID code. Afterwards, the leak test will be necessary to launch for reset the sensor ID. Vehicle Mode M01 M02 M03 M04 M05 M06 M07 M08 Default pressure (psi) 029 039 039 049 049 059 059 059 14 www.avetechnology.com to accept the default pressure 4) Press value. 5) Press 6) The pressure value on the far right digit will flash to change the pressure value. the 3rd digit. when entering the last digit. 8) Press 10) Press pressure value on the far left. to accept the displayed value on To change the pressure value, press to accept the input value. The message area will then proceed to the middle number. The pressure value in the middle will flash. Note: If the target pressure value is 28 psi, please enter it as 028 psi. Different unit, if needed, should be selected before setting up the pressure value. Please refer to UNIT MODE on page 12. button. The displayed number will increase by 1 button is pressed. Continue every time to press the button until you see the value you want. The number will loop from 0 to 9 and then back to 0. 9) Repeat step (6) to (8) to set up 2nd, which is the Correctly Enter Pressure Error in pressure Once done, the system will perform a check on the pressure entered. This is to avoid improper pressure setup for selected vehicle mode. 11) If the proper pressure has been entered, Message area will display PS (Pressure Saved). Display Unit will beep once. Entered pressure value will be saved. Return to the operating mode. 12) If improper pressure has been entered, Message area will display ERR Display Unit will beep twice. User will automatically be returned to step (6) to re-enter information. If error (ERR) occurs for the second time, the system will replace the pressure to the default value, and then return to the operating mode.

(Pressure Error). Note: If the pressure is above 999 kpa, only psi or bar Unit can work. Please refer to Unit Mode (p.12). 15 www.avetechnology.com 9-5. Setup the 2nd Standard Pressure Value is to setup Only with setting up the standard tire pressure value, the message area will display 2ND, the second standard which pressure when necessary. The previous setup will be the 1st standard tire pressure value. 1) To set up the second standard pressure

(YES) and follow value, press the steps (7) to (10) of PRESSURE SETUP MODE on page 14. 2) To exit without setting up the second standard pressure value, press

(NO) to return to the OPERATING MODE. 10 seconds of inactivity will also exit this setting and return to the operating mode. 9-6. Match Tires and the 1st or 2nd Standard Pressure To launch this setting, two different standard pressure values should be done first. In the operating mode, press and hold button for 6 seconds, and the message area displays SEL (Select 1st or 2nd standard pressure value). Tires in the same row will flash together, one row by one row. The spare tire will individually. Please press to match every row of tires and the 1st or the 2nd standard pressure value. The unit will beep once when matched. Afterwards, the unit will automatically return to the operating mode. flash

(SP1) or

(SP2) and To launch this setting, tires should be matched with two different standard pressure values first. Press and hold for 9 seconds, and the message area will display TOW. The trailer part will flash. 1) Press

(NO) to dismount the trailer. The unit will beep once when dismounted. 2) Press

(YES) to keep the trailer. The unit will beep once when done. 20 seconds of inactivity, or finishing the trailer mounting/dismounting, will get the unit back to the operating mode. 9-7. Mount/Dismount the Trailer (only for MO2-8 of the vehicle mode) 16 www.avetechnology.com 9-8. TIRE SETUP MODE (To change/rotate tires) and buttons Press and hold together for 3 seconds to enter TIRE SETUP MODE. In this mode, message area will display CHG. Press change tire position function. Pressing position and will goes to setting up sensor position.

(YES) to change tire position and

(NO) will not change the tire to confirm. Message area will There are 2 patterns:

(1) Front Wheels and Rear Wheels

(2) Front Right and Rear Left 1) Press 2) Press display OK?

Pressing goes back to change patterns.

(YES) will display OK and then to operating mode, while pressing

(NO) will display IDX and then goes back to operating mode. If no any activity for 20 seconds, it will automatically goes to setting up sensor position. Note: TIRE SETUP MODE is only for MO1 (Vehicle mode, please refer to page 13). As any other vehicle mode is picked, TIRE SETUP MODE will not be launched. TIRE SETUP MODE 1) front left and rear left front right and rear right 2) front right and rear left front left and rear right 17 www.avetechnology.com 9-9. Setup the sensor position 2) It is sometimes necessary to re-set up the sensor position, especially when replacing a tire sensor, replacing a new tire, or mixing up tires after rotating them. To set up the sensor position, follow the steps below:

1) Press and hold the two buttons and for 3 seconds. Message area will display LT (Leak Test) and the front left tire will flash. User will have 240 seconds (4 minutes) to perform the leak test on each tire. Inflate or deflate the tire by 34 kpa or 5 psi within 4 minutes. A sudden change in the tire pressure will cause the sensor to transmit signals continuously to let the display learn the sensor position. 3) The display unit will beep once and the message area will show OK if the signal is received. The flashing tire on the display unit will stop flashing. Then the front right tire takes the turn to flash. Follow step 2 to setup the front right tire. Note: All the tires take turns to be setup in the order 1>2>3>4..Please refer to page 13 or the tire numbers of each vehicle mode. 4) To delete a tire, press

. The message area will display DEL (tire location doesnt save) and the unit will beep once. Then message area display OK?

Press to delete this tire if there is no sensor installed or no tire existing in the position. Deleted position will not be monitored by the system. Press to skip the leak test on the tire. The message area will display SKP. The last default value will be kept. 5) System will proceed to the next tire to set up. Note: If all tires are completely set up, the system will exit TIRE SETUP MODE. Inactivity of more than 240 seconds (4 minutes), and the system will automatically return to the operating mode and save the last setting. Optional to leak test:

User can avoid performing a leak test on the tire by using the Optional AVE TPMS sensors LF remote control. Kindly refer to the page 21. 18 www.avetechnology.com 9-10. Reacting to Alerts NO SIGNAL Affected tire will flash during its turn when the unit is in operating mode. Unit will beep once every second. Antenna signal Icon shows with no bars. Pressure and Temperature bar indicators will light. No numbers will be in the Pressure and Temperature display. Note: Interference will affect signals reception. to turn off the sound. If the sound is Press turned off, the Warning will remain on the display until the problem is taken care of by the user. UNDER-INFLATION (25%) Affected tire will flash during its turn when the unit is in operating mode. Unit will beep once every two seconds Pressure bar indicator will flash at 75%

Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. The 25% under-inflation value in pressure display is based on default 29 psi. UNDER-INFLATION (30%) Affected tire will flash during its turn when the unit is in operating mode. Unit will beep once every two seconds Pressure bar indicator will flash at 70%

Tire leak icon will light Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. The 30% under-inflation value in pressure display is based on default 29 psi. 19 www.avetechnology.com CAR BATTERY If the battery voltage falls below 11.5 volts or goes higher than 15.5 volts, the Battery chart will flash and the unit will beep once every two seconds. Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. OVER-INFLATION (25%) Affected tire will flash during its turn when the unit is in operating mode. Unit will beep once every two seconds Pressure bar indicator will flash at 75%

Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. The 25% over-inflation value in pressure display is based on default 29psi. OVER-INFLATION (30%) Affected tire will flash during its turn when the unit is in operating mode. Unit will beep twice every two seconds Pressure bar indicator will flash at 70%

Tire leak icon will light Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. The 30% under-inflation value in pressure display is based on default 29 psi. FAST LEAK Affected tire will flash during its turn when the unit is in operating mode. Unit will beep twice every second. Tire leak icon will light. Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. 20 www.avetechnology.com NO TIRE PRESSURE Affected tire will flash during its turn when the unit is in operating mode. Unit will beep twice every second Flat Tire icon will light Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. TEMPERATURE ABOVE 80C (176F) Affected tire will flash during its turn when the unit is in operating mode. Unit will sound one long beep followed by a one second delay Temperature icon will light Temperature bar indicator will flash Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. TEMPERATURE ABOVE 90C (194F) Affected tire will flash during its turn when the unit is in operating mode. Unit will sound one long beep follow by one short beep and a one second delay. Temperature icon will light. Temperature bar indicator will flash. Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. TEMPERATURE ABOVE 100C (212F) Affected tire will flash during its turn when the unit is in operating mode. Unit will sound one long beep followed by two short beeps and a one second delay. Temperature icon will light. Temperature bar indicator will flash. Note: Press to turn off the sound. If the sound is turned off, the Warning will remain on the display until the problem is taken care of by the user. 21 www.avetechnology.com 10. LF Remote Control In order to simply the complicated procedure of resetting the sensor position by inflating/deflating the wheels when rotating or changing the tires, Remote Control is the best choice. Without an LF Remote control, please rapidly inflate or deflate the tires, which functions the same as pressing the button B of the LF Remote control. Set/Reset the sensor position with LF and Setting the sensor position:

1. First, press and hold the buttons on the display together for 3 seconds to enter TIRE SETUP MODE. It will display CHG and then press

(NO) to learn the ID CODE of the sensors, while the message area will display LT (Leak Test) and the front left tire will flash. (TIRE SETUP MODE is only launched for MO1, p.13.) 2. Press the learning key B of LF (make LF near the valve stem of the front left tire), which will force the sensor to transmit signals so that the display can learn the position of the wheel. The display unit will beep once if the signal is received and the message area will display OK, and then the message area will turn to the next tire automatically. Before OK displayed, please do not move the LF away from the wheel. Repeat the same for the remaining tires. Delete/Skip one sensor:

Follow step one to enter TIRE SETUP MODE. When LT is displayed on the message area,

(YES) to delete press the tire, or press

(NO) to skip setting the tire. If any sensor is skipped, its previous status will be also kept. Once the tire has been deleted, it should be added back by repeating the procedure of setting sensor position. When the deleted tire is flashing again, learn the ID CODE with an LF or by rapidly deflating/inflating the tire. Spare tire can be deleted or added back in the same way.

(Please attend: when you learn the sensor ID into the display, please take other sensors away in the distance of 3 meters to avoid learning the other sensor ID.) Functions of the four buttons of LF:

A. Warning mode: Make sensors transmit signals per second for two minutes. After two minutes

(NO). The message area will display DEL. Press B. Walk up mode: Make sensors transfer signals every second for one minute. After one minute the sensors will get into normal mode. the sensors will get into normal mode. C. Normal mode: Make sensors transfer signals every 30 second. D. Sleep mode: Make sensors into sleep mode without transmitting any signal and save the batterys life. But when the sensor is put in the tire, the sensor will detect having pressure and automatically wake up. So when the sensor is installed in tire and you press D, it will not sleep due to the pressure. 22 www.avetechnology.com 11. Chart of Tire Setup Mode and Leak Test Press and hold for 3 seconds Tire Change Mode CHG shown on the right bottom of the display. Quit tire change mode and get to tire set up mode

(NO) LT shown on the right bottom of the display. Tire Set Up Dont set up the tire but confirm to delete the tire. No, dont delete but skip tire 1 Tire 1 flash

(NO)

(NO) Tire 2 flash Tire 3 flash Tire 4 flash

(YES) Select the tire changing way Confirm the tire change and get to tire set up mode Set up Tire 1

(YES) Yes, delete tire 1 Get the remote control near tire 1 and press and hold B button for 5 seconds. Follow the same steps to get to others 23 www.avetechnology.com 12. AVE TPMS Extended Antenna Cable (for Trucks/Buses/Trailers) The far distance between the driver cabinet and the rear tires

(like a truck or bus) may cause the poor antenna. Besides, the thickness of the vehicle stamping parts, car window films with volumes of metal material, and so on will also cause the interference with the signal transmitting. To make sure of the signal well-transmitted and well-received, an extended antenna cable would be strongly in need for trucks/buses/trailers. Make sure the connection is tight enough. Figure 1 Red line = Antenna Cable. Figure 2 Must set the antenna cable to the central area among all the wheels. 24 Figure 3 www.avetechnology.com 13. AVE TPMS Optional Accessories Battery Pack (8AA ) Battery Pack allows display unit to be carried around for easier setup. Users do not have to rely on the power from the vehicles cigarette lighter power cord. Useful when setting up vehicles with a lot of wheels. AVE TPMS will support up to 27 wheels LF Remote control for Tire Sensors The LF remote control is used to control the tire sensors. The 2 main functions include;

Learning Key (A) Press this key to force the sensor to transmit a signal without tires pressure to learn the wheel position. It also has the function to exchange the tires position. inflating or deflating Sleep Key (D) It will force the sensor into sleep mode so it will the save the tire sensors battery power. This will only work if the sensor is removed from the wheel, or there is no air pressure in the tire. As soon as the sensor detects air pressure, the sensor will automatically wake-up. This is useful when changing tire location (tire rotation) to setup up the tire position. It will force the tires sensor to transmit a signal instead of performing the leak test (page 19). Use as a diagnostic tool to test the tires sensor if a sensor is transmitting a signal. Standard Valve AVE TPMS uses a standard metal valve. Common valve which is available anywhere. Allows you to replace just the tire valve if it is damaged or broken. You do not have to replace the entire sensor. With other TPMS units, you have to replace both the valve and the sensor if either one is broken or damaged. Tires sensor Tire sensor is available for the spare tire. To purchase more tire sensors, please contact your AVE TPMS retailer. 25 www.avetechnology.com bar psi KPa 0.1 1.5 10 0.2 2.9 20 0.3 4.4 30 0.4 5.8 40 0.5 7.3 50 8.7 0.6 60 10.2 0.7 70 11.6 0.8 80 90 13.1 0.9 100 14.5 1.0 110 16.0 1.1 120 17.4 1.2 130 18.9 1.3 140 20.3 1.4 150 21.8 1.5 160 23.2 1.6 170 24.7 1.7 180 26.1 1.8 190 27.6 1.9 200 29.0 2.0 210 30.5 2.1 220 31.9 2.2 230 33.4 2.3 240 34.8 2.4 250 36.3 2.5 260 37.7 2.6 270 39.2 2.7 280 40.6 2.8 290 42.1 2.9 300 43.5 3.0 C

-40

-30

-20

-10 0 10 KPa 310 320 330 340 350 360 370 380 390 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 F

-40.0

-22.0

-4.0 14.0 32.0 50.0 14. Appendix Pressure Conversion Table psi 88.5 89.9 91.4 92.8 94.3 95.7 97.2 98.6 100.1 101.5 103.0 104.4 105.9 107.3 108.8 110.2 111.7 113.1 114.6 116.0 117.5 118.9 120.4 121.8 123.3 124.7 126.2 127.6 129.1 130.5 KPa 610 620 630 640 650 660 670 680 690 700 710 720 730 740 750 760 770 780 790 800 810 820 830 840 850 860 870 880 890 900 bar 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 psi 45.0 46.4 47.9 49.3 50.8 52.2 53.7 55.1 56.6 58.0 59.5 60.9 62.4 63.8 65.3 66.7 68.2 69.6 71.1 72.5 74.0 75.4 76.9 78.3 79.8 81.2 82.7 84.1 85.6 87.0 bar 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 9.0 psi 132.0 133.4 134.9 136.3 137.8 139.2 140.7 142.1 143.6 bar KPa 9.1 910 9.2 920 9.3 930 9.4 940 9.5 950 9.6 960 9.7 970 9.8 980 990 9.9 1000 145.0 10.0 1010 146.5 10.1 1020 147.9 10.2 1030 149.4 10.3 1040 150.8 10.4 1050 152.3 10.5 1060 153.7 10.6 1070 155.2 10.7 1080 156.6 10.8 1090 158.1 10.9 1100 159.5 11.0 1110 161.0 11.1 1120 162.4 11.2 1130 163.9 11.3 1140 165.3 11.4 1150 166.8 11.5 1160 168.2 11.6 1170 169.7 11.7 1180 171.1 11.8 1190 172.6 11.9 1200 174.0 12.0 Temperature Conversion Table F 68.0 86.0 104.0 122.0 140.0 158.0 C 20 30 40 50 60 70 C 80 90 100 110 120 125 F 176.0 194.0 212.0 230.0 248.0 257.0 26 www.avetechnology.com 15. WARRANTY AVE Technology warrants to the original end user that the product purchased is free from defects in material and workmanship for a period of one (1) year from the date of original purchase. Should the product fail within the warranty period, it will be replaced or repaired at the option of AVE Technology. AVE Technology reserves the right to replace defected products with either a new or refurbished unit, to be functionally equivalent to new. The Warranty is void and inapplicable if:

1. 2. 3. 4. the product has been used or handled other than accordance with the instructions in the user manual the product is abused, misused, damaged by accident or neglect the damage is due from being repaired or tampered with by anyone other than an AVE Technology or an authorized AVE Technology repair center. the damage is due from shipping during transit. The damaged product must be delivered prepaid to AVE Technology or its authorized AVE Technology repair center. The RETURNED PRODUCT MUST BE ACCOMPANIED BY A WRITTEN DESCRIPTION OF THE DEFECT AND A PHOTOCOPY OF THE ORIGINAL PURCHASE RECEIPT. This warranty is valid in the country of purchase This warranty is limited to the terms stated herein. AVE Technology shall not be liable for any special, incidental or consequential damages relating to the product sold. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state.

-------------------------------------------(Please cut along line)--------------------------------------------------

WARRANTY REGISTRATION FORM Last Name First Name Apartment Number City Country Product Warranty 1 Year House Number 2 Years Street Name Zip/Postal Purchase Date YEAR State/Province Phone Model MO DD

-

-

27 www.avetechnology.com