RFbeam Microwave GmbH Datasheet AGD-T7813-125 Issue 1 MC-133 Introduction This document describes the AGD-T7813 modules Issue 1. This module has the following features:
Improved Ceramics Material (Temex E2036) RF-Transistor with higher gain Adjusted PCB Layout with tighter coupling for Resonator (lower loss) Electrical Specification Parameter Conditions / Notes Symbol Min Typ Max Unit Operating conditions Supply voltage Supply current VCO input voltage Module enabled RF-Part disabled VCO pin resistance Internal pulldown 100k Operating temperature Storage temperature Power down/Enable RF power down Input tied high with pullup 100k RF enable Minimum enable time RF-part fully functional Maximum hold time LP capacitor charge error < 10%
Transmitter Transmitter frequency UVCO= 3.0V, Tamb= 25C Frequency drift vs temp. Vcc=3.3V, -20C .. +70C Frequency tuning range (VCO) UVCO= 1V .. 5V VCO sensitivity VCO Modulation Bandwidth f=1MHz Output power EIRP Output power deviation Full VCO tuning range Spurious emission According to ETSI 300 440 Receiver Antenna gain LNA gain FTX=24.125GHz FRX=24.125GHz Mixer Conversion loss fIF =500Hz Receiver sensitivity fIF =500Hz, B=1kHz, S/N=6dB Overall sensitivity fIF =500Hz, B=1kHz, S/N=6dB Vcc Icc1 Icc2 Uvco Rvco Top Tst VIH1 VIL1 ton toff fTX fTX fvco Svco BVCO PTX PTX Pspur GAnt GLNA Dmixer PRX Dsystem 3.15 40 0
-20
-40 2.7
-0.2 5 3.3 60 5 100k 6.0 V 80 10 5.5
+70
+85 mA mA V C C Vcc+ 0.3 V 0.7 2 V s ms 24.120 24.125 24.130 GHz 35 200
+13
-0.27 50 12.5 MHz/C 70 MHz MHz/V kHz
+16
+20 dBm
+/- 2 dBm
-30 dBm 15 9
-2.0
-114
-130 dBi dB dB dBm dBc RFbeam Microwave GmbH www.rfbeam.ch Page 1/5 RFbeam Microwave GmbH Datasheet AGD-T7813-125 Issue 1 MC-133 Parameter Conditions / Notes Symbol Min Typ Max Unit IF output IF output impedance IF Amplifier gain I/Q amplitude balance fIF =500Hz, UIF=100mVpp I/Q phase shift fIF =500Hz, UIF=100mVpp IF frequency range
-3dB Bandwidth IF noise voltage IF output offset voltage fIF =500Hz fIF =500Hz Vcc = 3.3V Supply rejection Rejection supply pins to IF outputs, 1kHz Antenna Horizontal -3dB beamwidth E-Plane Vertical -3dB beamwidth H-Plane Horiz. sidelobe suppression Vert. sidelobe suppression Body Outline Dimensions connector left unconnected Weight Connector RIF GIF UIF fIF_AC UIFnoise UIFnoise Uos_AC Dsupply W W D D 100 30 3 90 dB dB 110 500k Hz 3.2 7.9 V/Hz 70 20 1.0
-120
-110
-102 dBV/Hz 2.0 32 32 1.0 28 28
-20
-16 1.5 26 30 30
-25
-20 35*65*17 62 8 V dB dB dB mm3 g pins Antenna Pattern Typical Antenna Pattern for one antenna (RX- or TX-side). Measured at 24.200GHz:
RFbeam Microwave GmbH www.rfbeam.ch Page 2/5 RFbeam Microwave GmbH Datasheet AGD-T7813-125 Issue 1 MC-133 Block diagram Frequency vs. VCO-Voltage and Temperature Pin 8 voltage vs. Temperature RFbeam Microwave GmbH www.rfbeam.ch Page 3/5 RFbeam Microwave GmbH Datasheet AGD-T7813-125 Issue 1 MC-133 Connector Pinout On module side a Samtec HW-04-15-F-D-325-SM connector with the following pinout is used:
1:
2:
3:
4:
5:
6:
7:
8:
/Enable
+3.3V GND Q Out I Out VCO S&H Temp Enable/Disable RF-part. Connect to 0V for normal operation Power Supply. Connect to +3.3V (3.15V .. 6.0V) Ground connection. Connect to 0V Analog Output Q-Channel Analog Output I-Channel Frequency control input. A voltage between 1..5V adjusts TX Frequency by 0 .. 50MHz. Can be used for FSK or FMCW Sample&Hold Switch Analog Output. Leave it open or connect to +3.3V for normal operation Temperature Sensor output of LMT84 temperature sensor Mechanical Drawing
*
FCC Labelling Information: (label to be placed into the recess position * shown in the mechanical drawing above FCC ID: WH3 -MC-133 AGD-T7813-125 (MC-133) Frequency 24.125GHz Issue 1 Serial No: in barcode or datamatrix format RFbeam Microwave GmbH www.rfbeam.ch Page 4/5 Datasheet AGD-T7813-125 Issue 1 MC-133 RFbeam Microwave GmbH FCC Approval This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance such that the module should not be installed in equipment intended to be used within 20cm of the body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications not expressly approved by AGD SYSTEMS Ltd could void the user's authority to operate the equipment Manufacturers of mobile or fixed devices incorporating MC-133 modules are authorized to use the FCC Grants of the MC-133 modules for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID: WH3-3-MC-133". Document History Author:
Date:
Version:
Changes:
Lon Audergon, RFbeam Microwave GmbH, CH-9008 St. Gallen August 25th 2015 1.1 I- and Q-outputs exchanged Different drawings added RFbeam Microwave GmbH www.rfbeam.ch Page 5/5