FCC ID: 2ATLGAL510 UHF RFID Reader

Ver:1.0.1 Quick User Manual AL-510 RFID READEREquipment/Software Control Ver:1.0.1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution (15.19 statement) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Non-modification Statement:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Ver:1.0.1 Welcome! This User Manual is to guide you through the steps of setting up your AL-510 RFID reader. You will find in below sections of how to connect your AL-510 to your devices, and how to use it to get the results you want in reading RFID tags. RFID Solutions Software AL-510 has two methods available to develop your own application/software:

AL-510 Software Development Kit (C#) AL-510 Utility Read Tool Keyboard Read Mode We provide various antenna patterns, such as near field, far Antenna field, and induction field, so as to meet the changeable field environment. General Inlay Metal Inlay Customized Inlay RFID inlay This RFID inlay has a wide frequency range from 860 to 960 MHz; which means you can make your own choices to use NXP, Impinj, or Alien RFID chip, as all of them are compatible with this RFID inlay. The product package should contain the following items:

1*AL-510 RFID UHF Reader 1* User Manual 1*Power Supply 1*Wi-Fi Antenna AL-510 RFID UHF INTERFACE 1. +12VDS Power supply 2. Ethernet 3. RS232 Serial port (DB15 to DB9) 4. USB type-B HID port 5. Wi-Fi 802.11 b/g/n, 2.4GHz 6. GPIO & RS485 In d u s t r i a l C o n t a c t 7. Support 4 antennas INDICATOR LIGHTS Status Blink When reading tags Signal Blink Reader is enabled / signal processing On Reader is disabled, please restart Power On Reader is ready Off Reader Wi-Fi is not connected to Wi-Fi AP Wi-Fi Blink Reader Wi-Fi is connected to AP On Reader Wi-Fi is connected to the program Ver:1.0.1 Use AL-510 to Read Tags 1. To Connect Your AL-510 via Wired Network, with Default IP: 192.168.1.91 A. Securely insert the Ethernet cable into both the ports of AL-510 and your computer, and download DS Manager (http://tibbo.com/support/downloads/tdst.html). On DS Manager, search AL-510, and click on Settings to revise IP-address to 192.168.1.91. Ethernet B. Securely insert the Ethernet cable into both the ports of AL-510 and your computer, and revise IP-

address to 192.168.1.X. Your AL-510 should be ready by now. Ver:1.0.1 2. To Connect Your AL-510 via Wireless Network Step 1: Use the Ethernet cable (Wired Network) to connect AL-510 to your computer. Step 2: Set up a wireless network for AL-510 on Utility Demo Menu (as shown below). In the section of Wi-Fi AP, type in a name and a password for this wireless network. In the section of Settings for Wi-Fi Fixed IP Click on DHCP Turnoff, and type in accordingly, ReaderIP (10.35.2.53), ReaderPort (1001), Mask (255.255.255.0), and Gateway (10.35.2.254). After completing these steps, click Setting. 3. Use AL-510 Utility Demo Menu to Read Tags Step 1: Connect an antenna to the first port on AL-510 Reader. Step 2: Open up AL-510 Utility Demo Menu. Type in IP (192.168.1.91 as default) and click Connect to connect to AL-510 Reader. Place the RFID tags within the reading range of the antenna, then click Start in the section of Inventory, you will see the read tags shown on the list below. Ver:1.0.1 4. Use USB Keyboard Mode to Read Tags Step 1: Use the Ethernet cable (Wired Network) to connect AL-510 to your computer. Step 2: Click Keyboard on AL-510 Utility Demo Menu, and you can configure the reading method in Keyboard Mode. Step 3: Connect an antenna to the first port on AL-510 Reader. Step 4: Place the RFID tags on the antenna, then the list of read tags will appear wherever you have your cursor at. Below uses Notebook to demo the testing results. If you would like to stop using Keyboard Mode, please click HID in the section of USD Output Format. Note: When you use Keyboard Mode to read tags, the antenna will automatically change to PORT 1.

CERPASS TECHNOLOGY CORP. Report No.: 1903151 Photographs of EUT Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 1 of 5 CERPASS TECHNOLOGY CORP. Report No.: 1903151 RF Chip Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 2 of 5 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 3 of 5 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 4 of 5 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 5 of 5

CERPASS TECHNOLOGY CORP. Report No.: 1903151 Photographs of EUT Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 1 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 2 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 3 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 4 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 5 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 6 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 7 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Antenna position Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 8 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 9 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 10 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 11 of 12 CERPASS TECHNOLOGY CORP. Report No.: 1903151 Cerpass Technology Corp. Issued Date

: Jul. 10, 2019 Page No.

: 12 of 12

YAP-100CP RFID UHF Antenna Data Sheet 860~960MHz(return loss -10dB) 902~928MHz(return loss -14dB) 50 1.9(860~960MHz) 1.2(902~928MHz) 6dBic(860~960MHz) 7dBic(902~928MHz) Right Hand, Circular Operating Frequency Impedance VSWR Gain Polarization Front/Back Ratio 13dB Radiation Pattern HPBW

(3dB Beam Width) Connector Directional 70 10@E-plane , 70 10@H-plane (860~960MHz) 70 5@E-plane , 70 5@H-plane (902~928MHz) N Jack Input power Dimensions Weight 10W(Max) 225 x 225 x 40 mm 660g YAP-100CP Antenna Drawing YAP-100CP Radiation Pattern @915MHz 915MHz 120 150 180 10 5 0

-5

-10

-15

-20 210 150 240 E-plane Ex E-plane Ey 120 180 10 5 0

-5

-10

-15

-20 210 240 H-plane Ex H-plane Ey 10 5 0

-5

-10

-15

-20

-25

-30

-30

-25

-25

-20

-15

-10

-5 0 5 10 10 5 0

-5

-10

-15

-20

-25

-30

-30

-25

-25

-20

-15

-10

-5 0 5 10 270 915MHz 90 90 60 30

-30

-30 -25 -20 -15 -10 -5 0 5 10 0 300 60 330 30

-30

-30 -25 -20 -15 -10 -5 0 5 10 0 330 300 270

RF_160, Issue 02 Declaration of Authorization We Name: Aidialink Corp. Address: No.6, Lising 6th Rd., Science Park, City: Hsinchu City, 30078 Country: Taiwan Declare that:

Name Representative of agent: Delia Feng Agent Company name: Cerpass Technology Corporation Address: No.10, Lane 2, Lianfu Street, Luzhu Township City: Taoyuan County 33848 Country: Taiwan, R.O.C. is authorized to apply for Certification of the following product(s):

Product description: UHF RFID Reader Type designation: AL-510 Trademark: AidiaLink on our behalf. Date: Jun. 18, 2019 City: Hsinchu City Name: PH Liu @

Function: General Manager Signature: PVs veces Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

FCC, Request for non-disclosure Date: 10-Aug-09 RF_501, Issue 5 Page 1 of 1 Company Name: Aidialink Corp. Address: No.6, Lising 6th Rd., Science Park, City: Hsinchu City, 30078 Country: Taiwan To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2ATLGAL510 Reference number: ##4H##

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

LJ Bill's) of Material Block Diagrams X Operational Description I Schematic Diagrams LC Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission's policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):

CJ Internal Photos [] User's Manual L Test Set-up Photos ( External Photos Justification:

Planned Release Date STC: (notes 2, 3, 4, 5) Date: 2019/06/18 Name and signature of applicant: PH Liu (Y Jw Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period