FCC ID: 2AWVWAPH2016 Smart Air Purifier

Smart Air Purifier Model: AP-H2016 READ AND SAVE THESE INSTRUCTIONS Safety Instructions

@ Only use Smart Air Purifier as described in this manual. Do not use without removing the plastic wrap from the filter. If not removed, the air purifier will not filter air, and may overheat, causing a fire hazard. Do not use the air purifier outdoors. Keep the air purifier away from water or wet, damp areas. Never place in water or liquid. Do not use in excessively humid areas. eKeep the air purifier away from heat sources such as stovetops, ovens, or radiators. Do not use where combustible gases, vapors, metallic dust, aerosol (spray) products, or fumes from industrial oil are present. eKeep 5 feet / 1.5m away from where oxygen is being administered. e Supervise children when they are near the air purifier. Do not place anything into the openings of the air purifier. Do not place heavy objects on the air purifier. Keep the inside of the air purifier dry. To prevent moisture build up, avoid placing in rooms with major temperature changes or underneath air conditioners. e Always unplug the air purifier before servicing (such as when changing the filter). Do not use the air purifier if it is damaged or not working correctly, or if the power cord or plug is damaged. Do not repair yourself. Contact Customer Support. WARNING: To reduce the risk of fire or electric shock, do not use this air purifier in combination with any 3rd party controls (such as a dimmer switch). Not for commercial use. Household use only. LIRE ET CONSERVER CES INSTRUCTIONS Consignes de scurit eVeuillez uniquement utiliser le Purificateur dair intelligent comme dcrit dans ce manuel. e Veuillez retirer l'emballage plastique du filtre avant d'utiliser le purificateur dair. Auquel cas, le purificateur dair ne filtrera pas l'air, et provoquer une surchauffe, pouvant mener a un incendie. Veuillez ne pas utiliser le purificateur d'air en extrieur. Gardez le purificateur a l'abri de l'eau ou de zones humides ou mouilles. Veuillez ne pas placer le purificateur dans de l'eau ou du liquide. eVeuillez ne pas utiliser le purificateur dair dans des zones dhumidit excessive. Gardez le purificateur dair a l'abri de sources de chaleur telles qu'une cuisinire, un four ou un radiateur. Veuillez ne pas utiliser le purificateur dair en prsence de gaz combustibles, vapeur, poussire mtallique, produits arosols (spray) ou fumes d'huiles industrielles. Maintenez 1,5 m (5 pieds) de distance avec l'entre doxygne. e Veuillez ne pas laisser des enfants a proximit du purificateur d'air sans surveillance. Veuillez ne pas placer dobjets dans les ouvertures du purificateur dair. Veuillez ne pas placer dobjets lourds sur le purificateur dair.

@ Maintenez Iintrieur du purificateur dair au sec. Afin dviter la cration d'humidit, veuillez ne pas placer le purificateur dair dans des pices dont la temprature varie fortement ou sous des climatiseurs. Veuillez toujours dbrancher le purificateur d'air avant maintenance (ex. : lors du changement du filtre). e Veuillez ne pas utiliser le purificateur d'air s'il est endommag ou ne fonctionnement correctement, ou si le cordon d'alimentation ou la prise sont endommages. Neffectuez pas de rparations vous-mme. Veuillez contacter le Service client.

@ AVERTISSEMENT : Afin de minimiser le risque dincendie ou de choc lectrique, veuillez ne pas utiliser le purificateur dair avec des contrdleurs tiers (comme un variateur). eA usage non commercial. Usage personnel uniquement. Package Includes Item Quantity Smart Air Purifier 1 3-in-1 True HEPA Filter (Pre-Installed) 1 Quick Start Guide 1 User Manual 1 Power Adpater 1 Specifications Adapter Input 100~240V ~ 50/60Hz Power Supply 24V=1.5A Purifier Rated Power 29W 527 ft? / 49 m2 Note: Effective for larger rooms, but purification will Effective Range take longer. Ideal Room Size is based on 5 air changes per hour (ACH). CADR 240 CFM / 408 m3/h Noise Level 24~52dB Air Purifier Dimensions 9.9 x 9.9x 17.3 in / 25.2 x 25.2 x 44cm Air Purifier Weight 7.7 Ib /3.5 kg

. a Temperature: 14 to 104F / -10 to 40C Operating Conditions Humidity: < 85% RH Getting to Know Your Smart Air Purifier a. Panel g. Filter Cover Handle b. Air Outlet h. Non-slip Pads c. Housing i. 3-in-1 True HEPA Filter d. Air Inlet j. DC Input Port e. Dust Sensor k. Adapter Output Cable f. Filter Cover |. Power Adapter pr 8 h f. ono Upside Down

[|p :

_ Getting Started 1, Rotate the bottom filter cover 2. Remove the filter from its plastic packaging counterclockwise and take it out. and place it back into the air purifier. 3. Reattach the filter cover and rotate 4, Place the air purifier on a flat, stable surface clockwise to lock. The sound of "dah" with the panel facing up. Allow at least indicates the filter cover is tighted up. 15 in / 38 cm of clearance on all sides of the air purifier. Keep away from anything that would block airflow, such as curtains and cabinet. 15in /38em 15 in/ 38cm 5. Insert the adapter output cable into the DC input port, then plug the power adapter into a 120V socket. Now your purifier is ready to use!

Using Your Smart Air Purifier Note: You could peel off the protective film on the panel before using. 1. Functions & Controls On/Off Button Press to turn Smart Air Purifier on/off. Fan Speed Button Press to cycle through fan speeds: | (low), II (medium), and III (high). Note: Tapping the Fan Speed Button while the air purifier is in Auto Mode, Sleep Mode or Custom Mode (if the display is on) will exit that mode. Timer Button Press to cycle thorugh timer options: 2H, 4H, 8H, and cancel. The purifier will turn off automatically when the set timer has expired. Sleep Mode Button Press to turn Sleep Mode on or off. When Sleep Mode is on, the air purifier will work in its lowest noise setting and the panel's brightness will dim for more comfortable use at night.

@) Auto Mode Button Press to turn Auto Mode on or off. The purifier will automatically adjust based on the environmental air quality. Custom Mode Button Press to turn Custom Mode on or off. The fan speed can be steplessly adjusted in the app and this customized speed will be saved and used when Custom Mode is on. Lock Button Press for 3 seconds to turn on Lock Mode. The panel buttons will be locked and cannot be triggered. Press for another 3 seconds to turn Lock Mode off. The Lock Mode Indicator will flash 3 times when any other button is pressed to remind that Lock Mode is still enabled. Filter Change Indicator Button When the filter expires, its exchange indicator will light up in red. After replacing with the new filter, press the button for 3s. If the indicator flashes 3 times, the reset is completed. Note:

e After the filter is reset, its usage time will be recalculated. e The exchange indicator can also be reset by pressing the button for 3 second even it does not light up. Memory Function This air purifier will save its previous settings when powered off (such as speed, mode, and Wi-Fi connection), and when it is powered back on, the settings will resume. 2. LED Indicators Indicator Working Status Light Status

| Low Speed Solid White Il Medium Speed Solid White WW High Speed Solid White 2H Auto-off in 2 Hours Solid White 4H Auto-off in 4 Hours Solid White 8H Auto-off in 8 Hours Solid White Sleep Mode is On Solid White

@ Auto Mode is On Solid White Custom Mode is On Solid White Locked Solid White Unlock Dim Locking Reminder Triple Flashes Filter is Expired Solid Red Filter Reset Successfully Triple Flashes Ready for Wi-Fi Connection Slowly Flashes White

= Wi-Fi is Connecting Quickly Flashes White Wi-Fi is Connected Solid White Powering On Air Purifier Slowly breathes with green, blue, yellow, then red. Air Quality is Excellent Green Air Quality is Good Blue Air Quality is Moderate Yellow Air Quality is Poor Red Care & Maintenance Cleaning the Smart Air Purifier Do not clean with abrasive chemicals or flammable cleaning agents. Cleaning Steps 1.Unplug before cleaning. 2.Wipe the outside of the air purifier with a soft, dry cloth. If necessary, wipe the housing with a damp cloth, then immediately dry. 3.It is recommended to vacuum the inside of the purifier. Cleaning the Filter Do not clean the filter with water or other liquids. =_ The outer pre-filter should be cleaned every 2-4 weeks to increase its efficiency and extend its lifespan. The pre-filter should be cleaned by a soft brush or vacuum hose to remove hair, dust, and large particles. IN 2 Filter When to Clean Howto Clean When to Replace Pre-Filter Every 2-4 weeks Useasoft brush or vacuum Does not require hose. Do not clean the filter replacing with water or other liquids. H13 True HEPA Filter No clean No clean 6-8 months Activated Carbon Filter No clean No clean 6-8 months Note: A 3-stage filter includes a Nylon Pre-Filter, True HEPA Filter, and Carbon Filter. The three parts of the filter should be replaced as a single unit. Filter Change Time Period The filter should be replaced every 6-8 months. The exact date at which your filter may need to be changed may vary depending on how often you use your air purifier. Using your air purifier in an environment with relatively high pollution may mean you will need to replace the filter more often, even if the filter change indicator is off. The filter needs to be replaced in any following case:

e Increased noise e Decreased airflow e Unusual odors eA visibly clogged filter Resetting Filter Change Indicator When the Filter Change Indicator fi lights red, it prompts to reset the filter service life. e Press and hold fi for 3 seconds. fi2will flash 3 times and then turn off once successfully reset. e fi will light up as a reminder to replace the filter. The indicator should turn on within 6-8 months, though this time period can be longer or shorter based on the actual usage. You may not need to replace your filter yet, but you should check it when fi turns on and plan to replace it soon. e Reset the Filter Change Indicator when you have replaced the filter. Storing If not using the air purifier for an extended period of time, wrap both the air purifier and the filter in plastic packaging and store them in a dry place to avoid moisture damage. Troubleshooting The troubleshooting section below is for solving frequently asked questions for the purifier unit. If your problem persists, please contact customer support. For Smart Air Purifier Problem Air purifier will not turn on or respond to touch controls. Airflow is signifi-

cantly reduced. Air purifier makes an unusual noise while the fan is on. Strange smell is coming from the air purifier or it has poor odor removal ability. Possible Solution Plug in the air purifier. Check to see if the power cord is damaged. If so, stop using the air purifier and contact Customer Support. Plug the air purifier into a different outlet. The air purifier may be malfunctioning. Contact Customer Support. Make sure the filter is removed from its packaging and properly in place. Tap to increase the fan speed. Make sure there are at least 15 inches / 38 cm of clearance on all sides of the air purifier. The pre-filter may be clogged by large particles, such as hair or lint, blocking air flow. Clean the pre-filter. Replace with a new filter. Make sure the filter is properly in place with plastic packaging removed. Make sure the air purifier is operating on a hard, flat, level surface. Replace the filter. The air purifier may be damaged, or a foreign object may be inside. Stop using the air purifier and contact Customer Support. Do not try to repair the air purifier. Clean the filter or replace if necessary. Make sure not to use your air purifier in an area with high humidity or while diffusing essential oils. Remove the filter and expose it to the sun, until the smell can be reduced from the activated carbon filter. Poor air purifica-

tion quality. Filter Change Indicator is still on after replacing the filter. Filter Change Indicator has not turned on within 8 months. Filter Change Indicator turned on before 6 months. Tap to increase the fan speed. Make sure no objects are blocking the sides or top of the air purifier

(the inlet or outlet). Make sure the filter is fully removed from its packaging and is properly secured in place. Close doors and windows while using the air purifier. If the room is larger than 527 ft? / 49 m2, air purification will take longer. The air purifier may not be as effective in significantly larger rooms. Replace the filter. Press and hold fi for 3 seconds. fit will flash 3 times and turn off once successfully reset. fi is a reminder for you to check the filter and will light up based on how frequently the air purifier has been used. If you dont use your air purifier often, efi: will take longer to turn on. i is a reminder for you to check the filter and will light up based on how long the air purifier has been used. If you run your air purifier frequently, fi will turn on sooner. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

(1) Reorient or relocate the receiving antenna.

(2) Increase the separation between the equipment and receiver.

(3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

(4) Consult the dealer or an experienced radio/TV technician for help. FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device."

Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) fappareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme a la norme NMB-003 du Canada. IC RF Statement:

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matire d'exposition RF. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Shenzhen Intellirocks Tech. Co., Ltd. is under license.

6040.5 ~

040.5 fi . SAirplove l Model No. : AP-H2016 IC: 26287-APH2016 oN es Rated Voltage: DC 24V FCC ID: 2AWVWAPH2016- Intertek Rated Current: 1.54 5015014 CONFORMS TO UL STD. 507 CERTIFIED TO CSA STD .C22.2 NO. 113 Manufacturer : Airplove (Xiamen) Electronic Co.,Ltd. Date Code :XXXX SN:

This device complies wih Part 18 othe FCC Rules, Operations subject the folowing wo conditions

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Declaration Letter We Airplove (Xiamen) Electronic Co., Ltd. hereby declare that the product Smart Air Purifier / AP-H2016 is not capable of operating with channel 12 and 13 in regions of US and Canada. Versions of the product available for import and sale in the US and Canada will not operate on channels 12 and 13. It will not be possible for users and configure these channels in the US and Canada version. By: ______________________ yulian Zhao

(Signature1)

(Print name) Title: Certificate engineer ________ On behalf of: Airplove (Xiamen) Electronic Co., Ltd._________

(Company Name) Telephone: ______ +86 15005056461___________________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Authority to Act as Agent Date: August 30, 2021 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

_____ Intertek Testing Service Shanghai ______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: ____2022/8/30_____ By:

(Signature1) _____ yulian Zhao______

(Print name) Title:

____ Certificate engineer ___ _ On behalf of: Airplove (Xiamen) Electronic Co., Ltd.

(Company Name) Telephone:

______ +86 15005056461__________ 1 - If a group entity is designated as the authorized agent, the letter of authorization must identify those individuals within the group who are authorized to take action on the application; or alternatively a statement must be provided indicating that as the authorized agent, any individual within the group entity is authorized to act on behalf of the applicant /

grantee and take action on the application. See https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=33316 . 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 012916 09

Date: August 30, 2021 Subject: Confidentiality Request for: FCC ID: 2AWVWAPH2016 Request for Confidentiality Pursuant to FCC 47 CRF 0.457(d) and 0.459, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent*1 Permanent Permanent Permanent Permanent Permanent*

Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual

*Note: ______(Insert Explanation as Necessary)______ Airplove (Xiamen) Electronic Co., Ltd. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180)2___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By:__________________________

(Signature/Title3) _______ yulian Zhao_____

(Print name) 1 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting. 2 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.