FCC ID: PIDAS1030 LTE Base Station Radio

AirSpeed 1030 B48 Installation Guide Part Number: DUG01623 System Release: 17.5 Revision: A1 Published: August 2020 Copyright by Airspan Networks Ltd., 2020. All rights reserved worldwide. Legal Notices The information contained within this document is proprietary, privileged and intended only for the recipient. As such, the information is subject to all relevant copyright, patent and other laws protecting intellectual property, as well as any specific agreements protecting Airspan Networks Ltd. rights in the aforesaid information. Neither this document nor the information contained herein may be published, reproduced, transmitted or disclosed to third parties, in whole or in part, without the express, prior, written permission of Airspan Networks Ltd. In addition, any use of this document or the information contained herein for the purposes other than those for which it is disclosed is strictly forbidden. Airspan Networks Ltd. reserves the right, without prior notice or liability, to make changes in equipment design or specifications. Information supplied by Airspan Networks Ltd. is believed in good faith to be accurate and reliable, while every care has been taken in preparing these documents. However, Airspan Networks Ltd. does not make any representations and gives no warranties of whatever nature in respect of these documents, including without limitation, the accuracy or completeness of any information, facts and/or opinions contained therein. No responsibility is assumed by Airspan Networks Ltd. for the use of the documents nor for the rights of third parties which may be effected in any way by the use thereof. The provision of these documents (and the documents themselves) does not constitute professional advice of any kind. Any representation(s) in these documents concerning performance of Airspan Networks Ltd. product(s) are for informational purposes only and are not warranties of future performance, either expressed or implied. Airspan Networks Ltd., its affiliates, directors, employees and agents shall not be held liable for any damages or losses, of any nature whatsoever, arising from any use of and/or reliance on the documents. These documents may contain flaws, omissions or typesetting errors; no warranty is granted nor liability assumed in relation thereto unless specifically undertaken in Airspan Networks Ltd. sales contract or order confirmation. Information contained herein is periodically updated and changes will be incorporated into subsequent editions. If you have encountered an error, please notify Airspan Networks Ltd. Product performance figures quoted within this document are indicative and for information purposes only. UK WEEE Registration number: WEEE/AB0207WZ. For more information, see WEEE Information for Airspan Customers and Recyclers. Acknowledgements Intel Corporation http://www.intel.com/

Microsoft Corporation http://www.microsoft.com AirSpeed 1030 B48 Installation Guide Table of Contents Document Information .............................................................................. 5 Abstract .................................................................................................................. 5 Revision History ..................................................................................................... 5 Warnings and Cautions ............................................................................ 6 Human Exposure to Radio Frequencies ................................................................ 6 Avertissement et Precautions dUtilisation ............................................... 6 Exposition des personnes aux frquences radiolectriques .................................. 6 Radio Interference ................................................................................................. 6 Modifications .......................................................................................................... 6 General .................................................................................................................. 6 Gnral .................................................................................................................. 6 Important Safety Instructions ............................................................................ 7 Safety ..................................................................................................................... 7 Securite .................................................................................................................. 7 Warning of Hazardous Voltages ............................................................................ 8 Attention aux Voltages Hasardeux ......................................................................... 8 Adherence to European Directive 2014/53/EU ...................................................... 8 Warning Symbols ................................................................................................... 8 Service Information ................................................................................................ 8 UL Information ....................................................................................................... 9 DECLARATION OF CONFORMITY ........................................................ 9 Maximum Output TX Power ................................................................... 11 Product Variants .................................................................................................. 11 Power Consumption ............................................................................................. 12 External Antennas (Optional) ............................................................................... 13 About This Document ............................................................................. 14 Purpose ................................................................................................................ 14 Intended Audience ............................................................................................... 14 Document Conventions ........................................................................................ 14 DUG01610 Airspan Commercial and Internal Use 1 AirSpeed 1030 B48 Installation Guide Related Reading .................................................................................................. 15 Customer Care Help Desk ..................................................................... 16 Airspan Encourages Comments .......................................................................... 16 1 Introduction ......................................................................................... 17 1.1 AirSpeed 1030 B48 ....................................................................................... 17 2 Getting Started ................................................................................... 18 2.1 Workflow of Installation ................................................................................. 18 2.2 AirSpeed 1030 B48 Installation Checklist ...................................................... 18 3 Verifying Prerequisites ....................................................................... 19 3.1 Verifying Site Requirements .......................................................................... 19 3.2 Verify Installation Requirements .................................................................... 19 3.2.1 Verify the Tools .............................................................................................. 19 3.2.2 Verify the Parts and Kits ................................................................................ 20 3.2.3 Power Supply ................................................................................................. 21 3.2.4 Connections ................................................................................................... 21 3.2.5 Physical Dimensions ...................................................................................... 23 3.2.6 Environmental ................................................................................................ 23 3.3 LEDs Display ................................................................................................. 24 4 AirSpeed 1030 B48 Installation .......................................................... 25 4.1 Back Bracket Assembly ................................................................................. 25 4.2 Connecting the GPS Antenna ....................................................................... 26 4.3 Weather-proofing Antenna Connections ....................................................... 26 4.4 Pole Mounting Assembly ............................................................................... 27 4.5 Wall Mount Assembly .................................................................................... 29 4.6 Tilt Adjustment .............................................................................................. 30 5 Connect and Manage Cables ............................................................. 31 5.1 Grounding ..................................................................................................... 31 5.2 Fiber Ethernet (SFP) Cable Preparation ....................................................... 31 5.3 Copper Ethernet Cable Preparation .............................................................. 35 5.4 DC Cable Preparation ................................................................................... 38 5.5 Remote (External) Antenna Assembly .......................................................... 42 DUG01623 Airspan Commercial and Internal Use 2 AirSpeed 1030 B48 Installation Guide A Job Sheet ........................................................................................... 44 B Checklist ............................................................................................. 45 C Abbreviations ...................................................................................... 46 Figures Figure 1: AirSpeed 1030 B48 (GPS Attached) ..................................................................................... 13 Figure 2: AirSpeed 1030 B48 Front View ............................................................................................. 17 Figure 3: Workflow ................................................................................................................................ 18 Figure 4: AirSpeed 1030 B48 Top Ports ............................................................................................... 21 Figure 5: AirSpeed 1030 B48 Bottom Ports .......................................................................................... 22 Figure 6: Back Bracket Assembly ......................................................................................................... 25 Figure 7: Attaching GPS Antenna ......................................................................................................... 26 Figure 8: Pole Mounting Assembly ....................................................................................................... 27 Figure 9: Mounted on Pole .................................................................................................................... 28 Figure 10: AirSpeed on Wall ................................................................................................................. 29 Figure 11: Tilt Adjustment ..................................................................................................................... 30 Figure 12: Ground Connection .............................................................................................................. 31 Figure 13: Pre-assembled LC Duplex Cable ........................................................................................ 31 Figure 14: Open Housing Lock ............................................................................................................. 32 Figure 15: Gland Nut on Cable ............................................................................................................. 32 Figure 16: Insert Tightening Cone on Cable ......................................................................................... 32 Figure 17: Insert Rubber Gland on Cable ............................................................................................. 32 Figure 18: Pass Cable thru Housing ..................................................................................................... 33 Figure 19: Insert Cable into Transceiver ............................................................................................... 33 Figure 20: Insert Holder over theTransceiver ....................................................................................... 33 Figure 21: Holder into Housing Base .................................................................................................... 33 Figure 22: Holder into Transceiver ........................................................................................................ 34 Figure 23: Lift Lever .............................................................................................................................. 34 Figure 24: Insert Gland ......................................................................................................................... 34 Figure 25: Insert Cone .......................................................................................................................... 34 Figure 26: Tighten Gland Nut ................................................................................................................ 35 Figure 27: Secure Housing Lock ........................................................................................................... 35 Figure 28: Pre-assembled RJ45 Cable ................................................................................................. 35 Figure 29: Gland Nut on Cable ............................................................................................................. 36 Figure 30: Insert Tightening Cone on Cable ......................................................................................... 36 Figure 31: Insert Rubber Gland on Cable ............................................................................................. 36 Figure 32: Insert Housing onto Cable ................................................................................................... 36 DUG01623 Airspan Commercial and Internal Use 3 AirSpeed 1030 B48 Installation Guide Figure 33: Insert Holder onto RJ45 ....................................................................................................... 37 Figure 34: Holder into Housing Base .................................................................................................... 37 Figure 35: Align RJ45 into Holder ......................................................................................................... 37 Figure 36: Lift Lever .............................................................................................................................. 37 Figure 37: Insert Gland ......................................................................................................................... 38 Figure 38: Tighten Gland Nut ................................................................................................................ 38 Figure 39: Secure Housing Lock ........................................................................................................... 38 Figure 40: Stripping Dimensions (DC Cable) ........................................................................................ 39 Figure 41: Open Housing Lock ............................................................................................................. 39 Figure 42: Seperate into Sections ......................................................................................................... 39 Figure 43: Insert Gland Nut ................................................................................................................... 40 Figure 44: Pass DC Cable Thru ............................................................................................................ 40 Figure 45: Tighten Two (2) Set Screws ................................................................................................ 40 Figure 46: Tighten the Strap Clamp ...................................................................................................... 40 Figure 47: Align Marks + Click in Place ................................................................................................ 41 Figure 48: Place Split Rubber Gland .................................................................................................... 41 Figure 49: Place Tightening Cone on Split Gland ................................................................................. 41 Figure 50: Tighten gland Nut................................................................................................................. 41 Figure 51: Secure Housing Lock ........................................................................................................... 42 Figure 52: Antenna RF Cables ............................................................................................................. 42 Figure 53: Connecting Antenna RF Cable ............................................................................................ 43 Tables Table 1: AirSpeed 1030 B48 ETSI Maximum Output TX Power .......................................................... 11 Table 2: AirSpeed 1030 B48 FCC Maximum Output TX Power ........................................................... 11 Table 3: Supported Frequency Bands .................................................................................................. 11 Table 4: Power Consumption ................................................................................................................ 12 Table 5: Typographic Conventions ....................................................................................................... 14 Table 6. Minimum Hardware Requirements ......................................................................................... 19 Table 7. Parts & Kits ............................................................................................................................. 20 Table 8. AirSpeed 1030 B48 Physical Dimensions .............................................................................. 23 Table 9. AirSpeed 1030 B48 Environment Compliance ....................................................................... 23 Table 10: LED Display .......................................................................................................................... 24 Table 11: ABBREVIATIONS & DEFINITIONS ...................................................................................... 46 DUG01623 Airspan Commercial and Internal Use 4 AirSpeed 1030 B48 Installation Guide Document Information Abstract This document details procedures for installing the Airspans AirSpeed 1030 B48 Pico-class LTE eNodeB variant. Revision History Revision Details Date Summary of Changes Rev 0.1 0.5 June 2020 Rev A Rev A1 June 2020 August 2020 Initial document draft comments Published after comments Added antenna variants + CBRS Note DUG01623 Airspan Commercial and Internal Use 5 AirSpeed 1030 B48 Installation Guide Warnings and Cautions Human Exposure to Radio Frequencies The AirSpeed 1030 B48 should be installed and operated from a minimum safe distance of at least 24.8 in. (63 cm) and installed higher than 2 meters to prevent unauthorized access. Avertissement et Precautions dUtilisation Exposition des personnes aux frquences radiolectriques Les AirSpeed 1030 B48 doivent tre installe et utilise de faon garantir la distance minimale de scurit de 63Cm et install plus de 2 mtres pour empcher tout accs non autoris. Radio Interference This AirSpeed 1030 B48 generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio, television reception or WiFi AP, which can be determined by turning the equipment on and off, the technician is encouraged to try to correct the interference by performing one or more of the following measures:

Re-orientate or relocate the unit Connect the equipment to an outlet on a circuit different from that to which the power source is Increase separation between the units and/or End Devices connected Modifications Any changes and modifications to this device that are not expressly approved by Airspan Networks may void the user's authority to operate the equipment. General Only qualified personnel should be allowed to install, replace, and service the equipment. The device cannot be sold retail, to the general public or by mail order. It must be sold to operators. Installation must be controlled. Installation must be performed by licensed professionals. Installation requires special training. The AirSpeed 1030 B48 should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void Airspan's product warranty and may expose the end user or the service provider to legal and financial liabilities. Airspan and its resellers or distributors are not liable for injury, damage or violation of regulations associated with the installation of units or antennas. Seul le personnel qualifi peut tre autoris pour installer ou remplacer lquipement ainsi queffectuer les oprations de maintenance pour cet quipement. Lquipement ne peut pas tre vendu en grande distribution ou par commande via email destination du public. Il doit tre vendu aux oprateurs de tlcommunications. Son installation doit tre contrle Son Installation doit tre effectue par des professionnels autorises. DUG01623 Airspan Commercial and Internal Use 6 Gnral AirSpeed 1030 B48 Installation Guide Son installation requiert une formation spcifique du personnel. LAirSpeed 1030 B48, radio et antenne doit tre installe UNIQUEMENT par des installateurs professionnels expriments et ayant une connaissance des constructions locales et rgles de scurit, ainsi que, ds que ncessaire, disposant dun agreement des autorits gouvernementales de rgulation. Toute enfreinte a ces obligations peut annuler la garantie dlivre par Airspan pour ces produits et peut exposer lutilisateur final ou le fournisseur de services a des dommages lgaux et financiers. Airspan et ses revendeurs ou ses distributeurs ne sont pas responsables des blessures, dommages ou violations de la rgulation en vigueur lies a linstallation du systme ou des antennes. Important Safety Instructions Read and Save these instructions This Installation Guide contains instructions and warnings that should be followed during installation, and operation. Failure to follow these instructions could cause bodily injury and/or product failure Safety Read this guide and follow all operating and safety instructions. No user serviceable parts inside. Position the power cord to avoid possible damage; do not overload circuits. Do not place this product on or near a direct heat source, and avoid placing objects on the terminal. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect the power before cleaning. The units should not be located near power lines or other electrical power circuits. It is the users responsibility to install this device in accordance with the local electrical codes. Installation of the AirSpeed 1030 B48 must be contracted to a professional installer. The circuit breaker should be easily accessible in case you have to disconnect the device. 10. When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance. Securite Lire attentivement ce guide et suivre les instructions dutilisation et de scurit. Aucune pice a lintrieur est dutilit pour lutilisateur. Positionner le cordon dalimentation de faon viter des dommages potentiels. Ne pas surcharger les circuits. Ne pas placer ce produit sur ou proximit dune source directe de chaleur et viter de placer des objets sur le terminal. Utiliser uniquement chiffon de coton pour nettoyage. Ne pas utiliser de produits liquides ou darosols. Dconnecter le produit de la source dalimentation avant nettoyage. Lunit ne doit pas tre situe trop prs de lignes lectriques ou autres circuits de puissance, avec lesquels il pourrait entrer en contact. Lutilisateur est tenu responsable de linstallation du produit conformment aux rgles lectrique en vigueur localement. DUG01623 Airspan Commercial and Internal Use 7 1. 2. 3. 4. 5. 6. 7. 8. 9. 1. 2. 3. 4. 5. 6. 7. AirSpeed 1030 B48 Installation Guide 8. 9. 10. Linstallation de AirSpeed 1030 B48 doit tre contractualise avec un installateur professionnel. Linterrupteur de circuit lectrique doit tre facilement accessible afin de pouvoir dconnecter lquipement. Lors de linstallation de la configuration finale, le produit doit tre conforme aux Standards de Scurit en vigueur ainsi quaux exigences rglementaires du pays dans lequel il est install. Si ncessaire, consulter les agences rglementaires appropries, ainsi que les autorits charges de linspection afin de garantir la conformit. Warning of Hazardous Voltages On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power. Remove metal jewellery that could come into contact with AC power. On DC sections, short-circuiting the low voltage, low impedance circuits can cause severe arcing that may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits. Note: Airspan products do not contain hazardous substances (as defined in UK Control of Substances Hazardous to Health Regulations 1989 and the Dangerous Substances Regulations 1990). At the end of any Airspan products life cycle, the customer should consult with Airspan to ensure that the product is disposed of in conformance with the relevant regulatory requirements. Attention aux Voltages Hasardeux Sur les installations de rseau lectrique de type courant alternatif (CA), des voltages hasardeux peuvent survenir. Garder une Attention particulire lors dune vrification ou de travaux sur rseau lectrique CA. Retirer tous bijoux en mtal qui pourraient entrer en contact avec lalimentation ou le rseau CA. Sur les portions de rseau lectrique de type courant continu (CC), un circuit basse impdance peut causer de srieux arcs lectriques qui pourraient bruler ou endommager les yeux. Retirer bagues, anneaux, montres etc afin dviter les court-circuit sur le rseau CC. Adherence to European Directive 2014/53/EU European Council Recommendation 2014/53/EU details basic restrictions and reference levels on human exposure to electromagnetic fields as advised by the ICNIRP. Adherence to these recommended restrictions and reference levels should provide a high level of protection as regards the established health effects that may result from exposure to electromagnetic fields. Warning Symbols The following symbols may be encountered during installation or troubleshooting. These warning symbols mean danger. Bodily injury may result if you are not aware of the safety hazards involved in working with electrical equipment and radio transmitters. Familiarize yourself with standard safety practices before continuing. Caution, hot surface Caution Electro-Magnetic Radiation DC Service Information Refer all repairs to qualified service personnel. Do not modify any part of this device, as this will void the warranty. Disconnect the power to this product and return it for service if the following conditions apply:

DUG01623 Airspan Commercial and Internal Use 8 AirSpeed 1030 B48 Installation Guide a. The terminal does not function after following the operating instructions outlined in this b. Liquid has been spilled, a foreign object is inside, or the terminal has been exposed to manual. rain. c. The product has been dropped or the housing is damaged. Locate the serial number of the terminal and record this on your registration card for future reference. Also record the MAC address, located on the product sticker. UL Information

- The electrical source must be properly grounded according with NEC and other local safety code requirements.

- AirSpeed 1030 B48 is designed to operate in environmental conditions complying with IP40 and relevant standards. DECLARATION OF CONFORMITY Declaration of Conformity with Regard to the R&TTE Directive 2014/53/EU Airspan tmto prohlauje, e tento pstroj je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 2014/53 / EU. Undertegnede, Airspan erklrer hermed, at flgende udstyrsenhed opfylder de vsentlige krav og andre relevante krav i direktiv 2014/53 / EF. Hiermit erklrt Airspan, dass die Produkteinheit die grundlegenden Anforderungen und anderen relevanten Bestimmungen der Richtlinie 2014/53 / EU erfllt. Kesolevaga kinnitab Airspan, et seadme seade vastab direktiivi 2014/53 / EL olulistele nuetele ja muudele knealuse direktiivi asjakohastele stetele. This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Por medio de este Airspan, declara que la unidad cumple con los requisitos esenciales y cualquier otra disposicin aplicable o exigible de la Directiva 2014/53 / UE.

, Airspan 2014/53 / E. Airspan dclare par la prsente que l'appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53 / UE. Con la presente Airspan dichiara che questa unit conforme ai requisiti essenziali e alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53 / UE. Czech:

Danish:

Deutsch:

Estonian:

English:

Espaol:

Greek:

Franais:

Italiano:

Latvian:

DUG01623 Airspan Commercial and Internal Use 9 AirSpeed 1030 B48 Installation Guide Ar o Airspan pazio, ka vienba atbilst Direktvas 2014/53 / ES btiskajm prasbm un citiem attiecgajiem noteikumiem;

is Airspan pareikia, kad is renginys atitinka esminius Direktyvos 2014/53 / ES reikalavimus ir kitas nuostatas. Airspan verklaart hierbij dat de apparaateenheid voldoet aan de essentile vereisten en andere relevante bepalingen van richtlijn 2014/53 / EU. Hawnhekk, Airspan, tiddikjara li din l-unit tikkonforma mar-rekwiiti essenzjali u dispoizzjonijiet rilevanti ora li jinsabu fid-Direttiva 2014/53 / UE. Alulrott, az Airspan kijelenti, hogy az egysg megfelel a 2014/53 / EU irnyelv vonatkoz alapvet kvetelmnyeinek s egyb kvetelmnyeinek. Niniejszym Airspan owiadcza, e urzdzenie jest zgodne z zasadniczymi wymaganiami i innymi odpowiednimi postanowieniami dyrektywy 2014/53 / UE. Airspan declara que esta unidade est em conformidade com os requisitos essenciais e outras disposies da Diretiva 2014/53 / UE. Airspan izjavlja, da je ta enota skladna z bistvenimi zahtevami in drugimi ustreznimi dolobami Direktive 2014/53 / EU. Airspan tmto vyhlasuje, e tento prstroj spa zkladn poiadavky a vetky prslun ustanovenia Smernice 2014/53 / E. Airspan vakuuttaa tten, ett laitteen tyyppi on direktiivin 2014/53 / EU olennaisten vaatimusten ja muiden asiaankuuluvien snnsten mukainen. Drmed intygar Airspan att denna enhet verensstmmer med de vsentliga egenskapskraven och andra relevanta bestmmelser som anges i direktiv 2014/53 / EU. Airspan lsir hr me yfir a essi eining uppfylli grunnkrfur og arar krfur tilskipunar 2014/53 / ESB. Airspan erklrer herved at utstyrsenheten oppfyller grunnleggende krav og andre relevante krav i direktiv 2014/53 / EU. Airspan declarm pe propria rspundere c produsul produsului respect cerinele eseniale i alte prevederi aplicabile din Directiva 2014/53 / UE. The Declaration of Conformity related to this product can be obtained from PLM@Airspan.com. Lithuanian:

Nederlands:

Maltese:

Hungarian:

Polish:

Portugus:

Slovenian:

Slovak:

Suomalainen:

Swedish:

slenska:

Norsk:

Romn:

DUG01623 Airspan Commercial and Internal Use 10 AirSpeed 1030 B48 Installation Guide Maximum Output TX Power Table 1: AirSpeed 1030 B48 ETSI Maximum Output TX Power Frequency Band ETSI Antenna Gain Variant

(MHz) TX (dBm) EIRP (dBm) 3550-3700 33 50 1030

(dBi) 17 Table 2: AirSpeed 1030 B48 FCC Maximum Output TX Power Frequency Band FCC Antenna Gain Variant

(MHz) TX (dBm) EIRP (dBm)

(dBi) 3550-3700 27.36 @ 10MHz 29.42 @ 20MHz 44.86 @10MHz 46.92 @20MHz 26.86 @ 10MHz 28.92 @ 20MHz 44.86 @10MHz 46.92 @20MHz 24.36 @ 10MHz 26.42 @ 20MHz 44.86 @10MHz 46.92 @20MHz 19.86 @ 10MHz 21.92 @ 20MHz 44.86 @10MHz 46.92 @20MHz 17.5 1030 18 1030 20.5 1030 25 1030 Note: The AirSpeed 1030 requires operation using an Airspan FCC-specific version of Netspan acting as a CBRS Domain Proxy. Caution: Do not set maximum output TX total power to higher than local regulations. Product Variants AirSpeed supports the following frequency bands with the specific performance values:

Table 3: Supported Frequency Bands LTE Band Variant Downlink Freq.

(MHz) Uplink Freq.

(MHz) Tx / Rx Conf. Tx Power per Port

(dBm) Power Source 48 AS103-U48-B03DP 3550-3700 3550-3700 2 x 2T2R 4x 33 (4x2W) DC DUG01623 Airspan Commercial and Internal Use 11 AirSpeed 1030 B48 Installation Guide Power Consumption Table 4: Power Consumption Power Source Nominal Power Consumption Max Nominal Power Consumption (W) DC 95 Note: Nominal Power Consumption (W) - refers to average power consumption over time.

(W) 65 DUG01623 Airspan Commercial and Internal Use 12 AirSpeed 1030 B48 Installation Guide External Antennas (Optional) AirSpeed 1030 B48 can be connected to external antennas (if required) via four (4) N-Type female connectors located at the top panel. The antenna should be mounted to its appropriate mounting facility. The supported antennas should be dual slant, cross polar, DC grounded antennas. Note: For a list of compatible external antennas, please contact your nearest Airspan Sales representative. Figure 1: AirSpeed 1030 B48 (GPS Attached) DUG01623 Airspan Commercial and Internal Use 13 AirSpeed 1030 B48 Installation Guide About This Document Purpose This guide provides the workflow and step-by-step procedures for installing the Airspans AirSpeed 1030 B48, Pico-class LTE eNodeB variant. These procedures include:

Verify prerequisites Connect and manage cables Install Back bracket & Pole/Wall bracket Install the AirSpeed 1030 B48 Intended Audience This guide is intended for persons who are responsible for installing the AirSpeed 1030 B48 equipment. Document Conventions This document uses the following typographic conventions. Table 5: Typographic Conventions Convention Element Blue underlined text Cross-reference links. Computer output Text displayed by the computer. Keyboard buttons and GUI elements. Command names or phrases. Website and e-mail addresses. Signifies a hazardous situationif not avoidedwill cause death or serious injury. Describes how to avoid it. Signifies a hazardous situationif not avoidedcan cause death or serious personal injury. Describes how to avoid it. Signifies a hazardous situationif not avoidedcan void the product warranty, and cause property damage. Describes how to avoid it. Provides necessary information to explain a task. Provides additional information. Provides helpful hints. Bold text Command Hyperlinks Danger Warning Caution Important Note Tip DUG01623 Airspan Commercial and Internal Use 14 AirSpeed 1030 B48 Installation Guide Related Reading The following documents contain related information:

AirSpeed 1030 B48 Product Datasheet Airspan LTE Commissioning Manual DUG01623 Airspan Commercial and Internal Use 15 AirSpeed 1030 B48 Installation Guide Customer Care Help Desk Airspans Customer Care Help Desk offers prompt and efficient customer support services. Note: To avail Airspans Customer Care Help Desk support, you must be a registered user and must have a valid support contract. To register, click here and fill the Registration form. To create and update issue logs, send e-mails to Customer Care Help Desk. Once you submit your issue, the system generates a new issue and sends an issue number for your reference. The system uses this issue number to categorize and store e-mails under the appropriate issue. To help Customer Care Help Desk identify your issue, include the issue number and your Customer Care Helpdesk account details in all further communications. Main Operations Airspan Communications Ltd. Capital Point 33 Bath Road Slough, Berkshire SL1 3UF, United Kingdom Tel: +44-1895-467-100 Worldwide Headquarters Airspan Networks Inc. 777, Yamato Road, Suite 105 Boca Raton, FL 3341-4408, USA Tel: +1 561 893 8670 Airspan Encourages Comments Airspan welcomes any feedback and suggestions that help to improve the quality of the documentation. Send your feedback to documentfeedback@airspan.com. DUG01623 Airspan Commercial and Internal Use 16 AirSpeed 1030 B48 Installation Guide 1 Introduction 1.1 AirSpeed 1030 B48 This section provides a descriptive overview of the Airspans AirSpeed 1030 B48 small cell eNodeB variant and its place in the Airspan product suite. AirSpeed 1030 B48 is part of Airspans carrier-class LTE Advanced outdoor small cell eNodeB family. AirSpeed 1030 B48 provides high-speed data, mobility, Voice over LTE, and broadcast/multicast services. AirSpeed 1030 B48 is a super compact, easy to install eNodeB, allowing an operator to deploy LTE broadband services on any Street Furniture, rooftop or building front. AirSpeed 1030 B48 is a dual sector / carrier 2x2 MIMO product with integrated front antenna. Note: For management please refer to the Airspan LTE Commissioning Manual as well as the Netspan User Manual. The AirSpeed 1030 B48 unit is displayed below. Figure 2: AirSpeed 1030 B48 Front View DUG01623 Airspan Commercial and Internal Use 17 AirSpeed 1030 B48 Installation Guide 2 Getting Started 2.1 Workflow of Installation Figure 3: Workflow The Workflow to install the AirSpeed 1030 B48 is displayed in the following diagram:

2.2 AirSpeed 1030 B48 Installation Checklist Plan the installation of the AirSpeed 1030 B48 by using the Installation Checklist, which you can find as a removable job aid in Appendix B for this guide. DUG01623 Airspan Commercial and Internal Use 18 AirSpeed 1030 B48 Installation Guide 3 Verifying Prerequisites Prior to installing the AirSpeed 1030 B48, verify the required safety, power, tools, parts and components. This chapter includes the hardware, software, and client requirements for installation. Important: Set up requirements for the installation is detailed in the Job Sheet, see Appendix A. 3.1 Verifying Site Requirements To set up the AirSpeed 1030 B48, an IP connection to a Netspan server is required. 3.2 Verify Installation Requirements 3.2.1 Verify the Tools Table 6. Minimum Hardware Requirements Tool Use Large flat bladed screwdriver 13 mm wrench securing the pole straps (bands) for securing M8 nuts 10 mm or 13/32 inch wrench for securing M6 nuts Note: Airspan does not provide screws and wall anchors for mounting the unit to the wall. The screw size depends on the structure of the building to which the unit is to be attached. When selecting screw sizes, consideration must be given to the weight of the unit and load that may be induced in windy conditions. DUG01623 Airspan Commercial and Internal Use 19 AirSpeed 1030 B48 Installation Guide 3.2.2 Verify the Parts and Kits Note: Verify order and requirements to ensure the correct unit type is being installed. Table 7. Parts & Kits Installation Kit

/ Part AirSpeed 1030, 3.55-3.7 GHz

(B48) Product Code Consisting of:

Images AS103-U48-

B03DP AirSpeed 1030, B48, Dual Sector, Integrated Antenna, DC GPS Antenna Kit GPS-ANT-4 AirSpeed 1030 universal pole and wall Mounting KIT AS103-U-PMK-1 Connector for DC connection -

included Accessories (ordered separately) GPS Antenna with Interference Rejection AirSpeed 1030 B48 mounting kit for 50 - 300 mm (2.0 to 11.8 inch) pole including:

1 - Pole mount Bracket Base kit, including back bracket and pole/wall mounting bracket 2- Maxi Clamps, band 9/16 wide + quick adjustment lock for 63mm-406mm (2.5"-16") Connector Adapter SFP CON-ADP-OCT-

SFP-1R OCTIS Connector Adapter SFP (ordered separately) Connector Adapter RJ45 CON-ADP-OCT-

RJ45-1R Adapter for RJ45 copper Ethernet connector ,Right (R) pitch 26mm

(ordered separately) DUG01623 Airspan Commercial and Internal Use 20 AirSpeed 1030 B48 Installation Guide 3.2.3 Power Supply AirSpeed 1030 B48 supports direct connection to -48VDC power source:

Operational Voltage Range: -40.5 to -57 VDC 3.2.4 Connections The following diagrams display the connections on the top and bottom panels of the AirSpeed 1030 B48. Note: The unit requires a secure ground connection and a grounding screw fitted with a flat washer and lock washer is provided on the back and clearly marked with the universal ground symbol. Figure 4: AirSpeed 1030 B48 Top Ports Note: RF ports 1 & 2 are specified as Sector 1. RF ports 3 & 4 are specified as Sector 2 DUG01623 Airspan Commercial and Internal Use 21 AirSpeed 1030 B48 Installation Guide Figure 5: AirSpeed 1030 B48 Bottom Ports Note: When the Serial port or one of the backhaul ports are not in use it should be sealed with a cap or plug to keep it secured and environmentally protected. DUG01623 Airspan Commercial and Internal Use 22 AirSpeed 1030 B48 Installation Guide 3.2.5 Physical Dimensions AirSpeed 1030 B48 is an outdoor enclosure. Table 8. AirSpeed 1030 B48 Physical Dimensions Variant Dimensions (H x W x D) Comment AirSpeed 1030 B48 Weight 500 x 285 x 125 mm / 19.68 x 11.22 x 4.92 in. The dimensions exclude connectors and protruding screws Main Unit 7.5 Kg / 16.53 Lbs. Mounting Bracket

(Bracket Base) 1 Kg. / 2.2 Lbs. 3.2.6 Environmental Note: AirSpeed 1030 B48 is not meant to be used in a Marine environment. AirSpeed 1030 B48 meets the following environmental requirements:

IEC 60529 IEC 60068 ETSI EN 300-019-2-4 Operational (non-weather protected equipment) ETSI EN 300-019-2-1 Storage (weather protected, not temperature controlled locations) ETSI EN 300-019-2-2 Transportation (Public Transportation) GR-63, Issue 4 Table 9. AirSpeed 1030 B48 Environment Compliance Type Details Operating temperature

-40C to 55C / -40F to 131F Operating humidity 5% - 100% non-condensing Storage temperature

-40C to 70 C / -40F to 158F Storage humidity Rain and Dust Ingress protection 5% - 100% non-condensing IP66 DUG01623 Airspan Commercial and Internal Use 23 AirSpeed 1030 B48 Installation Guide 3.3 LEDs Display Two (2) LEDs appear on the bottom of the unit, providing unit status indication. When powering up refer to the following table for indication of current status:

Table 10: LED Display Name Color Status Description Powering Up Yellow On Continuously Till the eNodeB SW starts loading Software loading Green Blinking (3Hz) While SW is loading Normal Operation Green On Continuously Normal operation (radiating) Major Alarm Critical alarm or Sector OOS Red Red Blinking (3Hz) Service not affected On Continuously Service affected DUG01623 Airspan Commercial and Internal Use 24 AirSpeed 1030 B48 Installation Guide 4 AirSpeed 1030 B48 Installation AirSpeed 1030 B48 offers two optional methods for outdoor mounting using the mounting kit, either:

Pole Mounting Wall mounting The AirSpeed 1030 B48 Mounting Kit - includes a back bracket and pole/wall mounting bracket for fastening the unit to a pole or on a wall. Prior to installation the back bracket must be assembled on the AirSpeed unit and then the mounting bracket must be affixed in place on either the pole or a wall. Note: Mounting kits are ordered separately. 4.1 Back Bracket Assembly Prior to installation the back bracket must be assembled on the AirSpeed unit, (unless pre-assembled). 1. Lie the unit on its face to expose the back. 2. Orient the back bracket so the lifting handle will be assembled in the direction of the top panel, where the GPS and RF ports are located. 3. 4. Line up the four (4) holes on the back bracket with four (4) threaded holes on the back of the AirSpeed unit. Insert and screw in the four (4) (M6 X 20) screws to tighten (tighten to a torque of no more than 5.2 Nm (46.02 in-lbs.) max., as shown below. Figure 6: Back Bracket Assembly DUG01623 Airspan Commercial and Internal Use 25 AirSpeed 1030 B48 Installation Guide 4.2 Connecting the GPS Antenna Note: The GPS Antenna Kit is ordered separately. Note: AirSpeed 1030 B48 works only with GPS antennas that are approved by Airspan. The following describes the connection of the GPS antenna which is installed directly to the top of the unit. 1. Unscrew the protective metal sealed cap from the GPS antenna jack prior to mounting the GPS on the AirSpeed-1030 B48 unit. 2. Align the GPS jack with the plug attached to the top panel on the unit. 3. Attach the GPS antenna to the TNC connector on the unit. Figure 7: Attaching GPS Antenna Caution: Take care not to over tighten so as not to damage the threads. Note: It is required to weather-proof all the antenna connections. This is done with a layer of self-

amalgamating tape followed by an over layer of PVC tape. See Weather-proofing Antenna Connections. Note: In the event no external GPS antenna is required (i.e. when used for 1588 clock sync), leave the sealed cap in place and weather-proof the antenna connection, as described below. 4.3 Weather-proofing Antenna Connections Note: The RF connectors on the Front Mount Antenna arrive pre-connected. Weather-proofing is best done at this stage to give easier access to the connections. Weather-proofing of the antenna connections is required. This is done with a layer of self-

amalgamating tape followed by an over layer of PVC tape. Verify the RF connector is completely weather-sealed. DUG01623 Airspan Commercial and Internal Use 26 AirSpeed 1030 B48 Installation Guide 4.4 Pole Mounting Assembly Caution: Mount the AirSpeed 1030 B48 unit in an orientation such that its ports (located on the bottom) face downwards. This prevents rain water from settling on the port, and thereby, avoiding damage to the unit such as corrosion and electrical shortcircuiting. The following describes the pole mounting procedure:

1. Select the location on the pole to mount the AirSpeed 1030 B48 mounting bracket. 2. Position the mounting bracket onto the pole at the required height. 3. Insert the clamp bands by passing them through the upper and lower slots in the bracket, in two (2) places 4. Assemble the 2 SEMS screws (M8 x 20) into the lower threaded holes on the mounting

(base) bracket, do not tighten. 5. Carefully align and position the unit so that the screws (1 on each side) fit into the notched grooves provided on the back bracket (pre-assembled on the unit) and hand tighten. Insert the M8 screws, washers and nuts (supplied) and fasten the back bracket (pre-assembled on the unit) to the mounting bracket. 6. Adjust the unit so that the GPS is positioned upright. Check and tighten all fixing screws.

(Tighten to a torque of no more than 12.5 Nm (9.22 ft-lb) max.) Figure 8: Pole Mounting Assembly DUG01623 Airspan Commercial and Internal Use 27 AirSpeed 1030 B48 Installation Guide The following displays the AirSpeed 1030 B48 mounted on a pole. Figure 9: Mounted on Pole DUG01623 Airspan Commercial and Internal Use 28 AirSpeed 1030 B48 Installation Guide 4.5 Wall Mount Assembly The following describes the wall mounting procedure:

1. Select the location on the wall to mount the AirSpeed 1030 B48 mounting bracket. 2. Position the mounting (base) bracket onto the wall at the required height and mark where to drill the holes. 3. Insert screws and appropriate wall anchors (not provided) and tighten in place. 4. Assemble the 2 SEMS screws (M8 x 20) into the lower threaded holes on the mounting

(base) bracket, do not tighten. Note: Wall plugs (x4) and necessary hardware are not supplied by Airspan and are the responsibility of the installer. Use appropriate wall plugs according to field conditions. 5. Carefully align and position the unit so that the screws (1 on each side) fit into the notched grooves provided on the back bracket (pre-assembled on the unit) and hand tighten. Insert the M8 screws, washers and nuts (supplied) and fasten the back bracket (pre-assembled on the unit) to the mounting bracket. 6. Adjust the unit so that the GPS is positioned upright. Check and tighten all fixing screws.

(Tighten to a torque of no more than 12.5 Nm (9.22 ft-lb) max.) Figure 10: AirSpeed on Wall DUG01623 Airspan Commercial and Internal Use 29 AirSpeed 1030 B48 Installation Guide 4.6 Tilt Adjustment On the AirSpeed 1030 B48 it is possible, after assembly to adjust the units tilt, either up or down. This allows for maximum system optimization and reduce interference while increasing coverage. There are adjustment slots located on the sides of unit body where it is attached to the Mounting bracket. Note: The AirSpeed 1030 B48 unit body has a yield of a maximum tilt of +20 (up) and -30 (down). Once the AirSpeed unit is mounted in place and a tilt adjustment is needed:

1. Slightly () loosen the four (4) bolts on both sides of the mounting bracket. 2. Adjust () the unit to the required tilt. 3. After adjustment to the required tilt () tighten all four (4) bolts on both sides. Figure 11: Tilt Adjustment DUG01623 Airspan Commercial and Internal Use 30 AirSpeed 1030 B48 Installation Guide 5 Connect and Manage Cables The following section explains the grounding procedure, cable preparation, external antenna assembly and general instructions on how to connect the DC power cable and the Fiber Ethernet

(SFP) cable to the AirSpeed 1050 unit. Note: Grounding cable, Fiber cables, SFP connector adaptor and AC power cable. Ethernet cables and RJ45 copper connector adaptor are not supplied as part of the AirSpeed 1030 B48 and can be ordered separately. The AirSpeed 1030 B48 requires a secure ground connection and a grounding screw fitted with a flat washer and lock washer is provided on the back and clearly marked with the universal ground symbol. The cable (not supplied) should be grounded and bonded according to international or local standards. 5.1 Grounding Figure 12: Ground Connection 5.2 Fiber Ethernet (SFP) Cable Preparation Note: Additional parts required for the SFP assembly:

LC Duplex cable assembly SFP Transceiver Note: To ensure proper operation, SFPs that are approved by Airspan should be used. The following displays the proper steps for SFP cable preparation:

1. Have the pre-assembled LC Duplex cable assembly ready. Note: Diameter of cable is in the 4.8 to 6.8mm (0.19-0.26) range. Figure 13: Pre-assembled LC Duplex Cable DUG01623 Airspan Commercial and Internal Use 31 AirSpeed 1030 B48 Installation Guide 2. Open the housing lock by sliding up then lift the clamp handle, Figure 14: Open Housing Lock 3. Separate the housing into its component sections. 4. Insert the gland nut through the front end of LC Duplex assembly. Figure 15: Gland Nut on Cable 5. Insert the split tightening cone from the side of the cable. Figure 16: Insert Tightening Cone on Cable 6. Insert the split rubber gland from side of the cable. Note: Make sure to select the correct gland size. Inner diameter of rubber gland is in the range of 4.8 to 6.8mm (0.19-0.26) range. Figure 17: Insert Rubber Gland on Cable 7. Pass the LC Duplex cable thru the housing. DUG01623 Airspan Commercial and Internal Use 32 AirSpeed 1030 B48 Installation Guide Figure 18: Pass Cable thru Housing 8. Insert the LC Duplex cable into the transceiver. A click is heard when engaged. Figure 19: Insert Cable into Transceiver 9. Insert the holder subset section from the front end of Transceiver. Figure 20: Insert Holder over theTransceiver 10. Fix the holder into the housing base. A click is heard when engaged. Figure 21: Holder into Housing Base 11. Secure the holder into the transceiver, click when engaged. DUG01623 Airspan Commercial and Internal Use 33 12. Lift the lever of housing base slightly so that the rubber gland, tightening cone and gland nut can be inserted and tightened correctly. Figure 23: Lift Lever AirSpeed 1030 B48 Installation Guide Figure 22: Holder into Transceiver 13. Push to insert the rubber gland. Figure 24: Insert Gland 14. Push to insert the tightening cone. Figure 25: Insert Cone 15. Tighten the gland nut with a 21mm wrench, to a torque of no more than 2-2.5 Nm (1.47 1.84 ft-lb) max. DUG01623 Airspan Commercial and Internal Use 34 AirSpeed 1030 B48 Installation Guide Figure 26: Tighten Gland Nut 16. Insert the connector into the SFP port on the bottom of the chassis. Verify that the connectors latch faces the rear of the unit to enable potential unlocking. 17. Close the lever and secure the lock by sliding the secondary lock/button, so that lever cant be lifted. Figure 27: Secure Housing Lock 5.3 Copper Ethernet Cable Preparation Note: A pre-assembled RJ45 cable is required for the Copper Ethernet assembly. The following displays the proper steps for the Copper (ETH) cable preparation:

1. Have the pre-assembled RJ45 cable assembly ready. Note: Diameter of cable is in the 5.8mm to 6.8mm or 8.8mm to 9.8mm range. Make sure to select the correct gland size. Figure 28: Pre-assembled RJ45 Cable 2. Insert the gland nut through the front end of RJ45 assembly. DUG01623 Airspan Commercial and Internal Use 35 AirSpeed 1030 B48 Installation Guide Figure 29: Gland Nut on Cable 3. Insert the split tightening cone from the side of the cable. Figure 30: Insert Tightening Cone on Cable 4. Insert the split rubber gland from side of the cable. Note: Inner diameter of rubber gland is in the 5.8mm to 6.8mm or 8.8mm to 9.8mm range. Make sure to select the correct gland size. Figure 31: Insert Rubber Gland on Cable 5. Insert the housing onto the RJ45 cable. Figure 32: Insert Housing onto Cable 6. Insert the holder section onto the front of the RJ45. DUG01623 Airspan Commercial and Internal Use 36 AirSpeed 1030 B48 Installation Guide Figure 33: Insert Holder onto RJ45 7. Fix the holder into the housing base. A click is heard when engaged. Figure 34: Holder into Housing Base 8. Ensure correct alignment of the RJ45 in the hosing by raising the lever to allow free movement and then push the RJ45 plug into the plug cap to ensure proper location, then lock the cap. Figure 35: Align RJ45 into Holder 9. Lift the lever of housing base slightly so that the rubber gland, tightening cone and gland nut can be inserted and tightened correctly. Figure 36: Lift Lever 10. Push the rubber gland to insert in place then push the tightening cone to insert in place. DUG01623 Airspan Commercial and Internal Use 37 AirSpeed 1030 B48 Installation Guide Figure 37: Insert Gland 11. Tighten the gland nut with a 21mm wrench, to a torque of no more than 2-2.5 Nm (1.47 1.84 ft-lb) max. Figure 38: Tighten Gland Nut 12. Insert the connector into the Copper Ethernet port on the bottom of the chassis. Verify that the connectors latch faces the rear of the unit to enable potential unlocking. 13. Close the lever and secure the lock by sliding the secondary lock/button, so that lever cant be lifted. Figure 39: Secure Housing Lock The following demonstrates the recommended assembly instructions, hardware and tool requirements for the proper DC cable assembly used by Airspan products. 5.4 DC Cable Preparation Note: Power Cable:

Diameter - 8.4mm to 9.4mm Wire Size - AWG16 to AWG14 Caution: Safety - Disconnection of power supply When AirSpeed unit is connected directly to wiring a suitably rated and easily accessible circuit breaker shall be incorporated externally to the equipment. Power source disconnection is required before disconnecting the power connector. DUG01623 Airspan Commercial and Internal Use 38 AirSpeed 1030 B48 Installation Guide Warning: This unit incorporates double pole/neutral fusing. Both the Line & Neutral have fuses in them. Warning: The onsite source circuit breaker (6A) should be gang operated, two (2) pole (single phase type). The following displays the proper steps for DC cable preparation:

1. Strip back and remove the outer sheath to a length of 9.0mm 2 (0.35 in) to expose the inner insulated wires to a length of 13.5mm 2 (0.53 in). Then strip back 7mm 2 (0.27 in) of the inner core insulation. Figure 40: Stripping Dimensions (DC Cable) 2. Open the housing lock by sliding up then lift the clamp handle. Figure 41: Open Housing Lock 3. Separate the housing into its component sections. Figure 42: Seperate into Sections 4. Insert the Gland nut through the other end of the cable. DUG01623 Airspan Commercial and Internal Use 39 AirSpeed 1030 B48 Installation Guide Figure 43: Insert Gland Nut Figure 44: Pass DC Cable Thru 5. Loosen the strap clamp and feed the prepared end of the source power cable into the inner part of the DC connector housing. 6. Secure the prepared ends of the cable into the inner part of the connector housing and tighten the 2 screws. Caution: Verify the wire polarity before securing. Figure 45: Tighten Two (2) Set Screws 7. Tighten the strap clamp screw as shown below. Figure 46: Tighten the Strap Clamp 8. Insert into outer housing until click in place, align marks for proper alignment. DUG01623 Airspan Commercial and Internal Use 40 AirSpeed 1030 B48 Installation Guide Figure 47: Align Marks + Click in Place 9. Place the split rubber gland onto the cable. Figure 48: Place Split Rubber Gland 10. Place the tightening cone onto the split rubber gland. Figure 49: Place Tightening Cone on Split Gland 11. Tighten the gland nut with a 21mm wrench, to a torque of no more than 2-2.5 Nm (1.47 1.84 ft-lb) max. Figure 50: Tighten gland Nut 12. Insert the connector into the Power port on the bottom of the chassis. Verify that the connectors latch faces the rear of the unit to enable potential unlocking. 13. Close the lever and secure the lock by sliding the secondary lock/button, so that lever cant be lifted. DUG01623 Airspan Commercial and Internal Use 41 AirSpeed 1030 B48 Installation Guide Figure 51: Secure Housing Lock Note: When securing the cable verify there is no tension on the connector so that it is easy to disconnect and re-connect for future maintenance actions. 5.5 Remote (External) Antenna Assembly Note: External antennas connected to AirSpeed 1030 B48 should be DC grounded. Caution: Power down the AirSpeed unit prior to disconnecting the antenna, to prevent damage. The AirSpeed 1030 B48 unit can utilize remotely attached antennas. For installation of the remotely mounted antennas follow the antenna manufacturers instructions and connect the antenna to the AirSpeed 1030 B48 using the appropriate cables. (Weather-proofed N-

type Heliax RF cables (ordered separately). 1. Carefully unscrew and disconnect each of the RF cables which connect the integrated antenna to the unit. Figure 52: Antenna RF Cables 2. Screw on a protective cap(s) on the integrated antenna cable, to prevent environmental damage, in the event they need to be re-connected. Weather-proof the caps (with a layer of self-amalgamating tape followed by an over layer of PVC tape). 3. Gather the cables securely together to prevent damage. 4. Attach, connect and secure the RF cable(s) between the external antenna and the appropriate RF connection on the top of the unit. 5. Weather-proof all cable connections, with a layer of self-amalgamating tape followed by an over layer of PVC tape. See Weather-proofing Antenna Connections. DUG01623 Airspan Commercial and Internal Use 42 AirSpeed 1030 B48 Installation Guide Figure 53: Connecting Antenna RF Cable Caution: Do not over-tighten the RF connector. RF failures can result when the RF connector is over-tightened. DUG01623 Airspan Commercial and Internal Use 43 AirSpeed 1030 B48 Installation Guide A Job Sheet This job sheet enables the users to keep track of their installation. It covers all the prerequisites required for accomplishing the AirSpeed 1030 B48 installation. Site Requirements o Position on Pole / Wall o Access restrictions (local regulations) (when applicable) o Method of reaching pole or wall positions (ladders, Elevated work platform) o Configuration programming details known o Point of connection for Ethernet (if applicable) o All equipment items available at the installation site o AirSpeed 1030 B48 unit o Mounting bracket kit o Cable assembly Tool Requirements

(For further information, see Verify the Tools.) o Large flat bladed screw driver o 13 mm wrench o 10 mm or 13/32 inch wrench o Large pliers o Hammer (to insert and set the wall plugs) Required Ancillary Equipment o Laptop PC for initial configuration o Ethernet cable for temporary connection of the lap top DUG01623 Airspan Commercial and Internal Use 44 AirSpeed 1030 B48 Installation Guide B Checklist During installation, review and perform all the steps on this checklist (in the given order). This checklist is meant for the person who performs the AirSpeed 1030 B48 installation. Tip: To make sure you complete all the tasks, detach or print this checklist and use it as a job aid. After performing, check off each task. Procedure Action Check If Performed Verify the prerequisites Verify the site requirements. Verify the installation requirements. Verify the tool requirements. Verify the parts & kits required. AirSpeed 1030 B48 installation Connect & manage Cables Install the back bracket and then the Pole/Wall bracket Install AirSpeed 1030 B48 on the mounting bracket (as required). Connect SFP or Copper cable (depending on the variant Connect power system Connect power cable DUG01623 Airspan Commercial and Internal Use 45 AirSpeed 1030 B48 Installation Guide C Abbreviations Table 11: ABBREVIATIONS & DEFINITIONS Expansion 3rd Generation Partnership Project, responsible for LTE Additive White Gaussian Noise is a channel model in which the only impairment to communication is a linear addition of white noise with a constant spectral density and a Gaussian distribution of amplitude. Bit Error Rate Decibel. A logarithmic unit used to describe a ratio (such as power ratio in radio telecommunications) An abbreviation for the power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW). It is used as a convenient measure of absolute power because of its capability to express both very large and very small values in a short form eNodeB Evolved Node B, is the element in E-UTRAN of LTE Encapsulating Security Payloads (ESP) provide confidentiality, data-origin authentication, connectionless integrity, an anti-replay service (a form of partial sequence integrity), and limited traffic-flow confidentiality E-UTRAN Evolved Universal Terrestrial Radio Access Network, is the air interface of 3GPP's Long Term Evolution Frequency-Division Duplexing. A transceiver mode where the transmitter and receiver operate at different carrier frequencies Global Navigation Satellite System is a term used to describe a satellite navigation system with global coverage. There are currently two fully operational GNSSs the US GPS and the Russian GLONASS. Half Power Beam Width is the angular separation in an antenna, in which the magnitude of the radiation pattern decreases by 50% (or -3 dB) from the peak of the main beam Internet Protocol Security is a protocol suite for securing Internet Protocol (IP) communications by authenticating and encrypting each IP packet of a communication session Light Emitting Diode Long Term Evolution Medium Access Controller responsible for several functions such Scheduling, Packet (De)Multiplexing, etc Term 3GPP AWGN BER dB dBm ESP FDD GNSS HPBW IPSec LED LTE MAC DUG01623 Airspan Commercial and Internal Use 46 AirSpeed 1030 B48 Installation Guide Term Expansion MME Mobility Management Entity is the key control-node for the LTE access-network. It is responsible, among other things for idle mode UE tracking and paging procedure including retransmissions MTBF Mean Time Between Failures NL Network Listening Orthogonal Frequency-Division Multiple Access (OFDMA) is a multiple access version of OFDM digital modulation scheme, used for eNodeB transmissions to UEs Protocol Data Unit Precision Time Protocol is used to synchronize clocks throughout a network. In this document, PTP is referring to IEEE1588-2008 protocol ROHS Restriction Of Hazardous Substances Serving Gateway. A Core entity in the LTE EPC architecture responsible for routing and forwarding user data packets, while also acting as the mobility anchor for the user plane during inter-eNodeB handovers and as the anchor for mobility between LTE and other 3GPP technologies SC-FDMA Single-Carrier FDMA is a frequency-division multiple access scheme, dealing with the assignment of multiple users to a shared communication resource. Used in LTE for UE transmissions to the eNodeB Software Defined Radio Time-Division Duplexing. A transceiver mode where the transmitter and receiver operate on the same carrier frequency User Equipment. The end user in LTE WEEE Waste Electrical and Electronic Equipment OFDMA PDU PTP S-GW SDR TDD UE DUG01623 Airspan Commercial and Internal Use 47

LABEL FCC ID:PIDAS1030 The label is affixed on the side panel of the base radio unit as shown below. The label material is PVC with a permanent adhesive. Airspan Networks Inc. AirSpeed 1030 3.550-3.700 GHz (B48) side panel, label with FCC ID:PIDAS1030 location Page 1 of 1

AW3782 Data Sheet Preliminary 3550 -3700MHz, Sector Antenna, FT The parameters in this specification follow the definitions and recommendations per NGMN P-Basta, Release 9.6 Average gain to RF connector LTE band Frequency range Azimuth HPBW Elevation HPBW Polarisation discrimination at 0 Front to back ratio (CoPol) Polarisation Electrical Down-tilt Impedance First side-lobe level VSWR Isolation between RF Ports Average transmission power per polarisation Peak transmission power per polarisation Connector type Cable Type Cable Length Labelling DC Grounding Connector to Cable Spec 48 3550 3700 MHz 17 0.5 dBi Dual Slant 45 70 5 8 5 22 dB 23 dB 0 50 ohms

-18 dB 1.5:1 25 dB 26 dBm 36 dBm 2 x N Type Male RA 0.141 50ohm 115mm 3mm See Outline Drawing on P2 Port 1/ 2/ 3/ 4 All Antenna ports to be DC grounded Recommended maximum dimensions PCB (mm) See Outline Drawing 117893-B Alpha Wireless Limited 2019. Last modified February, 05, 2020 Web: www.alphawireless.com Email: sales@alphawireless.com

* Alpha Wireless are always improving products; specification subject to change without notice. AW3782 Outline Drawing Alpha Wireless Limited 2019. Last modified February, 05, 2020 Web: www.alphawireless.com Email: sales@alphawireless.com

* Alpha Wireless are always improving products; specification subject to change without notice. AW3782 Revision Control Sheet Revision 0 Author Petr Svarc Date 05/02/2020 Description Initial Release Approved by Airspan Alpha Wireless Limited 2019. Last modified February, 05, 2020 Web: www.alphawireless.com Email: sales@alphawireless.com

* Alpha Wireless are always improving products; specification subject to change without notice.

Panel DATASHEET AW3014 AW3014 Common Name-

Common Name- 2 Port B42, 43 & 48 - 65 3300-3800MHz Frequency 2 Ports Fixed Tilt 18.0 Gain Beamwidth 65 PRODUCT INFORMATION PRODUCT INFORMATION This slimline solution was developed for xed wireless applications APPLICATION APPLICATION Alpha Wireless panel antennas provide wireless network operators the highest performance and quality. Panel antennas are generally used in sectorized applications. These antennas are designed for optimal radiation patterns improving overall network performance. Various tilt options are available to address network optimization requirements. STANDARD & CERTIFICATIONS STANDARD & CERTIFICATIONS Certification BS EN ISO 9001:2015 FEATURES FEATURES Wide-band antenna for 3GPP bands 42, 43 & 48. Dual Cross polarization antenna +/- 45 Mounting bracket with variable tilt (included) Manufactured in Ireland The parameters in this specification follow the definitions and recommendations per NGMN P-Basta, Release 9.6. Page 4/4 Publish Date: 01.03.2019 Publish Date:

01.03.2019 alphawireless.com alphawireless.com Revision no:

Revision no: 2323 Panel AW3014 AW3014 3300-3800MHz

+/-45 Slant Linear T0 or T4 18.0 65 3 7 1 50 1.5 14 28 30 18 16 100 TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION Electrical Specifications Electrical Specifications Frequency Range Polarisation Gain Azimuth Beamwidth Azimuth Beam Squint Elevation Beamwidth Electrical Downtilt Electrical Downtilt Deviation Impedance VSWR Return Loss Isolation Front to Back Ratio: Total Power +/-30 Upper Sidelobe Suppression, Peak to 20 Cross-Polar Discrimination Maximum Effective Power Per Port Radiation Pattern Files Radiation Pattern Files MHz Degree dBi Degree Degree<

Degree Degree Degree<

Ohms

dB>

dB>

dB>

dB>

dB>

W For radiation pattern files, please login at www.alphawireless.com Azimuth Azimuth Elevation Elevation Page 1/4 Publish Date: 01.03.2019 Publish Date:

01.03.2019 alphawireless.com alphawireless.com Revision no:

Revision no: 2323 Panel AW3014 AW3014 Windload Frontal (at Rated Wind Speed: 150km/h) Windload Lateral (at Rated Wind Speed: 150km/h) TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION Mechanical Specifications Mechanical Specifications Dimensions (Lx) Packing Size (LxWxD) Net Weight (antenna) Net Weight (mount) Shipping Weight Connector Type (Female) Connector Quantity Connector Position Survival Wind Speed Radome Material Radome Colour Product Compliance Environmental Lightning Protection Cold Temperature Survival Hot Temperature Survival Mechanical Illustration Mechanical Illustration All measurements are in mm (in) All measurements are in mm (in) mm (in) mm (in) kg (lb) kg (lb) kg (lb)

RAL C (F) C (F) N (Ibf) N (Ibf) km/h (mph) 750 (29.5) x 160 (6.2) x 81 (3.1) 823(32.4) x 240(94) x 178(7) 4.3 (9.4) 1.4 (3.1) 5.7 (12.5) N Type 2 Bottom 130 (30) 80 (18) 200 (125) UV-Stabilised PVC 7035 RoHS DC Grounded

-40 (-40) 70 (158) Page 2/4 Publish Date: 01.03.2019 Publish Date:

01.03.2019 alphawireless.com alphawireless.com Revision no:

Revision no: 2323 Panel AW3014 AW3014 TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION Mounting Bracket Kit Mounting Bracket Kit CL-V-102 Mount Kit M8 2.0mm (Mount Kit included with antenna) CL-V-102 Mount Kit M8 2.0mm (Mount Kit included with antenna) Mounting Kit Tilt Range Mounting Kit Material Mounting Kit Pole Diameter 0 to 10 Stainless Steel 50mm-115mm (2" to 4.5") ORDERING INFO ORDERING INFO AW3014-T0-N Zero Degrees Fixed Tilt with N Type Connectors AW3014-T4-N Four Degrees Fixed Tilt with N Type Connectors Enquiries Enquiries Ireland Ireland Ashgrove Business Centre, Ballybrittas, Portlaoise, Ireland Post code: R32 DT0A sales@alphawireless.com

+353 57 86 33847 USAUSA 11322 W 79th St, Lenexa, KS 66214, USA sales@alphawireless.com

+1 913 279 0008 Alpha Wireless Alpha Wireless DISCLAIMER The information in this document is provided solely regarding Alpha Wireless products. The information is not a guarantee of performance or characteristics. Alpha Wireless reserves the right to modify, change, amend, improve or make corrections to this document and its products, at any time and its sole discretion without prior written consent or notice. No license to any intellectual property rights is granted or implied under this document. Alpha Wireless disclaims warranties and liabilities of any kind including non-infringement of intellectual property rights of any third party. Alpha Wireless Limited 2014 Publish Date: 01.03.2019 Publish Date:

01.03.2019 Revision no:

Revision no: 2323 Page 3/4 alphawireless.com alphawireless.com

Panel DATASHEET AW3170 AW3170 Common Name-

Common Name- 2 Port B42 & 43 - 33 3300-3800MHz Frequency 2 Ports Fixed Tilt 20.5 Gain Beamwidth 33 PRODUCT INFORMATION PRODUCT INFORMATION Developed for xed wireless access applications requiring narrow Azimuth APPLICATION APPLICATION Alpha Wireless sector antennas are the most commonly used solution for designing high quality wireless networks. The 33 degree azimuth patterns allows to increase capacity to 6 sectors without increasing the number of sites. With additional options for xed tilt settings enables improved optimization. STANDARD & CERTIFICATIONS STANDARD & CERTIFICATIONS Certification BS EN ISO 9001:2015 FEATURES FEATURES Wide-band antenna for 3GPP bands 42 & 48 Dual Cross polarization antenna +/- 45 Narrow Azimuth beam to increase site capacity Mounting bracket with variable tilt Page 1/4 Publish Date: 14.11.2018 Publish Date:

14.11.2018 alphawireless.com alphawireless.com Revision no:

Revision no: 1515 Panel AW3170 AW3170 3300-3800MHz

+/-45 Slant Linear T0 or T4 20.5 33 3 7 1 50 1.5 14 25 27 17 16 100 TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION Electrical Specifications Electrical Specifications Frequency Range Polarisation Gain Azimuth Beamwidth Azimuth Beam Squint Elevation Beamwidth Electrical Downtilt Electrical Downtilt Deviation Impedance VSWR Return Loss Isolation Front to Back Ratio: Total Power +/-30 Upper Sidelobe Suppression, Peak to 20 Cross-Polar Discrimination Maximum Effective Power Per Port Radiation Pattern Files Radiation Pattern Files MHz Degree dBi Degree Degree<

Degree Degree Degree<

Ohms

dB>

dB>

dB>

dB>

dB>

W For radiation pattern files, please login at www.alphawireless.com Azimuth Azimuth Elevation Elevation Page 2/4 Publish Date: 14.11.2018 Publish Date:

14.11.2018 alphawireless.com alphawireless.com Revision no:

Revision no: 1515 Panel AW3170 AW3170 Windload Frontal (at Rated Wind Speed: 150km/h) Windload Lateral (at Rated Wind Speed: 150km/h) TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION Mechanical Specifications Mechanical Specifications Dimensions (Lx) Packing Size (LxWxD) Net Weight (antenna) Net Weight (mount) Shipping Weight Connector Type (Female) Connector Quantity Connector Position Survival Wind Speed Radome Material Radome Colour Product Compliance Environmental Lightning Protection Cold Temperature Survival Hot Temperature Survival Mechanical Illustration Mechanical Illustration All measurements are in mm (in) All measurements are in mm (in) mm (in) mm (in) kg (lb) kg (lb) kg (lb)

RAL C (F) C (F) N (Ibf) N (Ibf) km/h (mph) 750 (29.5) x 280 (11) x 85 (3.3) 793 (31.2) x 340 (13.3) x 178 (7) 6 (13.2) 1.5 (3.41) 7.5 (16.61) N Type 2 Bottom 220 (50) 80 (18) 200 (125) UV-Stabilised PVC 7035 RoHS DC Grounded

-40 (-40) 70 (158) Page 3/4 Publish Date: 14.11.2018 Publish Date:

14.11.2018 alphawireless.com alphawireless.com Revision no:

Revision no: 1515 Panel AW3170 AW3170 TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION Mounting Bracket Kit Mounting Bracket Kit CL-V-104 Mount Kit M12 2.5mm (Mount Kit included with antenna) CL-V-104 Mount Kit M12 2.5mm (Mount Kit included with antenna) Mounting Kit Tilt Range Mounting Kit Material Mounting Kit Pole Diameter

+2 to -10 Stainless Steel 50mm-115mm (2" to 4.5") ORDERING INFO ORDERING INFO AW3170-T0-N Zero Degrees Fixed Tilt with N Type Connectors AW3170-T4-N Four Degrees Fixed Tilt with N Type Connectors Enquiries Enquiries Ireland Ireland Ashgrove Business Centre, Ballybrittas, Portlaoise, Ireland Post code: R32 DT0A sales@alphawireless.com

+353 57 86 33847 USAUSA 11322 W 79th St, Lenexa, KS 66214, USA sales@alphawireless.com

+1 913 279 0008 Alpha Wireless Alpha Wireless DISCLAIMER The information in this document is provided solely regarding Alpha Wireless products. The information is not a guarantee of performance or characteristics. Alpha Wireless reserves the right to modify, change, amend, improve or make corrections to this document and its products, at any time and its sole discretion without prior written consent or notice. No license to any intellectual property rights is granted or implied under this document. Alpha Wireless disclaims warranties and liabilities of any kind including non-infringement of intellectual property rights of any third party. Alpha Wireless Limited 2014 Publish Date: 14.11.2018 Publish Date:

14.11.2018 Revision no:

Revision no: 1515 Page 4/4 alphawireless.com alphawireless.com

HD SERIESTM HIGH PERFORMANCE DISH ANTENNA HDDA3W 3300 TO 3800 MHz HIGH PERFORMANCE DISH ANTENNA The new HD Series dish antennas offered by Laird offers the system engineer the best performance available on the market. The antennas meet ETSI EN 302.326-3 DN1-DN5 specifications, the most stringent specifications for point to point backhaul antennas. The unique feed system is available in a single polarization version which can be mounted for either vertical or horizontal polarization. There is also a dual polarized version available for those systems which can utilize dual polarization to increase bandwidth or implement diversity. An optional fiberglass radome is available for added environmental protection. H-plane, 3.6GHz FEATURES Wide band operation Vertically or horizontally polarized Dual horizontal / vertical and dual-slant polarity models available Ultralow sidelobes, meets ETSI standards Extremely rugged for long service life in extreme environments TYPICAL ANTENNA PATTERNS i

i B d

n a G MARKETS 802.11 applications OFDM systems MIMO systems Cellular backhaul Point-to-point backhaul Public safety communications WiMAX

-150

-120

-180

-90

-60

-30 30 0 60 90 120 150 180 Azimuth []

3.6 GHz H-Plane H-plane, 3.6GHz 3.6 GHz E-Plane E-plane, 3.6GHz co-pol x-pol

-180

-150

-120

-90

-60

-30 0 30 60 90 120 150 180

-180

-150

-120

-90

-60

-30 0 30 60 90 120 150 180 Azimuth []

Elevation []

E-plane, 3.6GHz 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 0

-2

-4

-6

-8

-10

-12

-14

-16

-18

-20

-22

-24

-26

-28

-30 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 0

-2

-4

-6

-8

-10

-12

-14

-16

-18

-20

-22

-24

-26

-28

-30

i B d

n a G i co-pol x-pol

i B d

n a G i

i B d

i n a G 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 0

-2

-4

-6

-8

-10

-12

-14

-16

-18

-20

-22

-24

-26

-28

-30 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 0

-2

-4

-6

-8

-10

-12

-14

-16

-18

-20

-22

-24

-26

-28

-30 Americas: +1.847 839.6907 IAS-AmericasEastSales@lairdtech.com Europe: +44.1628.858941 IAS-EUSales@lairdtech.com Asia: +86.21.5855.0827.127 IAS-AsiaSales@lairdtech.com www.lairdtech.com

-180

-150

-120

-90

-60

-30 0 30 60 90 120 150 180 Elevation []

HD SERIESTM HIGH PERFORMANCE DISH ANTENNA HDDA3W SPECIFICATIONS PARAMETER Frequency range (single pol.) Frequency range (dual pol. ) VSWR (single pol.) VSWR (dual pol.) Impedance Cross-pol suppression Sidelobes Input power Mechanical downtilt Pole diameter (OD) Operating temperature PARAMETER Gain Beamwidth Front-to-back Weight Port-to-port isolation (dual pol.) MIN 3300 3300 2 (50)

-40 TYP 1.5:1 1.5:1 50

>30 dB MAX 3800 3800 1.7:1 1.8:1 100 30

+70 UNITS MHz MHz OHM W deg C ETSI EN 302.326-3 DN1-DN5 4 (101.6) inch (mm) HDDA3W-25-xx HDDA3W-29-xx 25 dBi 8.5

>30 dB

>30 dB 8 kg 29 dBi 6

>30 dB

>35 dB 10 kg Dimensions (diameter) 25.5 in (648 mm) 36.5 in (927 mm) WIND LOADING (LBS.) SYSTEM ORDERING HDDA3W-25-SP 25 dBi single polarity with N female connector HDDA3W-25-DP 25 dBi dual polarity with N female connector HDDA3W-29-SP 29 dBi single polarity with N female connector HDDA3W-29-DP 29 dBi dual polarity with N female connector DA5-29RADOME Fiberglass Radome Cover for 2ft (0.3m) dish DA5-32RADOME Fiberglass Radome Cover for 3ft (0.6m) dish MODEL HDDA3W-25 HDDA3W-29 HDDA3W-25 with Radome 75 HDDA3W-29 with Radome 100MPH 125MPH 113 256 111 177 116 400 174 NOTES All shipments F.O.B. Schaumburg, IL 60173 Dish antenna shown with optional radome ANT-DS-HDDA3W 0615 Any information furnished by Laird Inc. and its agents is believed to be accurate and reliable. All specifications are subject to change without notice. Responsibility for the use and application of Laird materials rests with the end user, since Laird and its agents cannot be aware of all potential uses. Laird makes no warranties as to the fitness, merchantability or suitability of any Laird materials or products for any specific or general uses. Laird shall not be liable for incidental or consequential damages of any kind. All Laird products are sold pursuant to the Laird Terms and Conditions of sale in effect from time to time, a copy of which will be furnished upon request. Copyright 2015 Laird Inc. All Rights Reserved. Laird, Laird Technologies, the Laird Logo, and other marks are trademarks or registered trademarks of Laird Inc. or an affiliate company thereof. Other product or service names may be the property of third parties. Nothing herein provides a license under any Laird or any third party intellectual property rights.

15.10.2011 ro Lette! OF AULNOIZAUION To whom it may concern, Please be notified that |, Brian Roberts, have designated Zion Levy in Airspan Networks Inc. as the person responsible for all FCC projects and to sign the form 731 and other documentation. Any and all acts carried out by Zion Levy in Airspan Networks Inc. on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. Sincerely Brian Roberts 15.10.2011

FCC, Request for non-disclosure RF_501, Issue 6 Date: 16-Jul-10 Page 1 of 1 Company Name: Airspan Networks Inc. Address:

777 Yamato Rd, Suite 310 Boca Raton, Florida City:

United States Country:

Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands To: Telefication B.V., Dept. FCC TCB Subject: Request for confidentiality FCC ID: PIDAS1030 Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):

Internal Photos Users Manual Test Set-up Photos External Photos Justification: This device is a new concept of LTE products and contains a trade secret of the company Planned Release Date STC: 180 days from the grant date (notes 2, 3, 4, 5) Name and signature of applicant: Zion Levi Date: August 05, 2020 Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

1) DC voltages/currents supplied to elements of the final radio frequency amplifying device for normal operation over the power range: 30 V/ 0.6 A. Company name:

Address:

Suite 310 Boca Raton FL 33431 USA AirSpeed 1030 3.55-3.7GHz (B48) statement Airspan Networks Inc. 777 Yamato Road Name of authorized person: Zion Levy Position:

Compliances Team Leader Date: July 14, 2020 Airspan Networks Inc. Tel: +1 561 893-8670; Fax: +1 561 893-8671, www.airspan.com

RF_160, Issue 04 Hermon Laboratories Ltd. . Harakevet Industrial Zone .. Binyamina 30500 .. Israel . Airspan Networks Inc. 777 Yamato Rd, Suite 310 Boca Raton, Florida 33431 USA. Declaration of Authorization We Name:

Address:

City:

Country:

Declare that:

Name Representative of agent: . (1) Agent Company name:

Address:

City:

Country is authorized to apply for Certification of the following product(s):

Product description: LTE Base Station Radio . Type designation: AirSpeed AS1030 3.550-3.700 GHz (B48). Trademark:

Validity/ expiry date August 05, 2019 on our behalf. Date:

City:

Name:

Function:

Airspan . August 05, 2020.. Zion Levy .. (2) Boca Raton .. Compliances Team Leader, R&D . Signature:

Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

Airspan Networks Inc. 777 Yamato Road Company name:

Address:

Suite 310 Boca Raton FL 33431 USA FCC ID:PIDAS1030 AirSpeed 1030 3.55-3.7GHz (B48) statement Each AirSpeed radio has been tested by an automatic testing station (which is calibrated weekly for accuracy), which calibrates the unit prior to testing. Each AirHarmony contains 4 transmitters therefore each in turn is calibrated by the station for RF output power accuracy. The calibration is then verified by transmitting on the RF output power approved for each frequency checking that it does not exceed the maximum conducted power allowed by the FCC as below:

10 MHz BW: Pout=26.61dBm +/- 0.75dB; Pmin=25.86 dBm ; Pmax=27.36 dBm 20 MHz BW: Pout=28.92 dBm +/- 0.5dB; Pmin=28.42 dBm ; Pmax=29.42 dBm For each frequency there is an internal software limit value that prevents the User from exceeding that RF output power setting. In the event the RF output power is higher then specified in the System Description, the AirHarmony radio doesnt pass and acquires a Fail status. AirHarmony boards with Fail statuses are rejected for final assembly of the product. The NMS management program also has internal specific FCC output limits that further checks and verifies maximum RF power output and prevents transmition above the FCC limits. Name of authorized person: Zion Levy Position:

Compliances Team Leader Date: August 23, 2020 Airspan Networks Inc. Tel: +1 561 893-8670; Fax: +1 561 893-8671, www.airspan.com