FCC ID: VH9SKXSLED-PCIEMV SLED-mPOS

6VH9KDC500 1 SLED-mPOS User Manual Rev 1.0 Dec. 2020 SLED-mPOS User Manual INTRODUCTION Table of Contents 1. INTRODUCTION ................................................................................ 5 1.1 Specification ....................................................................................................................... 6 1.2 Package ............................................................................................................................... 7 1.3 Characteristics .................................................................................................................... 8 1.4 Secure Touch Pinpad ..................................................................................................... 10 2. OPERATING YOUR SLED-MPOS ................................................ 11 2.1 Basics ................................................................................................................................ 11 Read NFC Tag (MIFARE) .......................................................................................................................... 11 Read Magnetic-Stripe Card .................................................................................................................... 11 Read IC Card ................................................................................................................................................. 11 3. WARRANTY ...................................................................................... 12 4. CONTACT INFORMATION ........................................................... 14 2 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. SLED-mPOS User Manual INTRODUCTION COPYRIGHT, LICENSE, and WARNING PAGE Copyright 2002-2021 by KOAMTAC, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from KOAMTAC, Inc. The material in this manual is subject to change without notice. KOAMTAC reserves the right to make changes to any product to improve reliability, function, or design. KOAMTAC does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. Follow all warnings and instructions marked on manual and units. Use only the power source specified in this manual or marked on the units. Certain KDC products may be covered by the following issued US patents numbers 7769917, 7954710, 8126399, 8295368, 8346979, 8347366, 8371506, 8483614, 8832323; Korea patents numbers 10-1383407, 10-1354252 and may be patent pending elsewhere, UK publication GB2492615, Korea publication 1020120128598. KDC is a registered trademark and property of KOAMTAC, Inc. KoamTac is a registered trademark and property of KOAMTAC, Inc. KTSync is a registered trademark and property of KOAMTAC, Inc. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO ANY TYPE OF MOISTURE. DO NOT LOOK DIRECTLY INTO LASER OR POINT THE LASER INTO ANOTHER PERSONS EYES. EXPOSURE TO THE BEAM MAY CAUSE EYE DAMAGE. CAUTION:

Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment. 3 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. SLED-mPOS User Manual INTRODUCTION Product Disposal This device should not be placed in municipal waste. Please check local regulations for disposal of electronic products. 4 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. SLED-mPOS User Manual INTRODUCTION 1. Introduction EMV/Chip&PIN/MSR/NFC Mobile POS Companion The PCI compliant EMV/MSR/NFC SmartSled design provides a secure and convenient user payment transaction. Chip-and-PIN payment solutions are becoming the global industry standard and as a result, KOAMTAC has developed the most advanced mobile payment companion. Being that it has a traditional magnetic stripe reader, as well as the newly implemented EMV functionality, the Mobile POS Companion allows businesses to take payments with existing swipe cards, as well as support those implementing the newly adopted EMV systems without changing of solutions. To find out more about KOAMTAC, Inc. and our family of products, visit us at www.KOAMTAC.com. 5 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. SLED-mPOS User Manual INTRODUCTION 1.1 Specification Main Processor 120MHz ARM Cortex-M4 Memory 1M program flash, 128KB RAM, 32-byte secure key storage, Display Keypad 8MB user data flash 128x64 monochrome Secure Touch Pinpad(15 buttons). '0 to '9', Up/Fn, Down/Menu, Cancel, Clear and Enter Mag-Stripe Reader Track 1/2/3, Bi-directional, ISO 7810, 7811, 7813 Smart Card Reader EMV L1 and L2, SAM Contactless and NFC Antenna : FPCB Type 2-Turn Loop Antenna with Ferrite Sheet

(NXP PN5180) Frequency : 13.56MHz PN5180 -> Card (Tx) : 100% ASK (Amplitude Shift Keying) Bit Encoding : Modified Miller Encoding Card -> PN5180 (Rx) : Subcarrier Load Modulation Bit Encoding :

106kBaud ->Manchester Encoding 212kBaud ->BPSK (Binary Phase Shift Keying) 424KBaud->BPSK (Binary Phase Shift Keying) ISO 14443, MIFARE, Felica, MasterCard PayPass, Visa PayWave Security Encryption PCI PTS V5.x For PIN : T-DES(128-bit) For Card data : T-DES(128-bit), AES(128-bit) Key Management DUKPT Key Injection Key Loader OS compatibility All major OS Interfaces USB to Serial (Micro USB port) Dimensions 65.1cm x 105.0cm x 10.1cm Weight Drop Spec 25.63 x 41.34 x 3.98 74.5g(2.63 oz) 5 feet (1.5M) Operating Temperature 32F (0C) ~ 122F (50C) Humidity 5% ~ 95% (noncondensing) 6 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. SLED-mPOS User Manual INTRODUCTION 1.2 Package The standard SLED-mPOS package contains:

1. One SLED-mPOS 2. USB Cable l 5pin Micro USB cable 7 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. SLED-mPOS User Manual INTRODUCTION 1.3 Characteristics Before starting to use the SLED-mPOS, the user should become familiar with its physical characteristics. Refer to the follow figure that indicate the placement of Secure Touch Pinpad, OLED display, LED, NFC Reader, Magnetic-Stripe Card Reader, IC Card Reader and ports on the KDC. 8 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. SLED-mPOS User Manual INTRODUCTION NFC Reader OLED Display Secure Touch Pinpad IC Card Reader Magnetic-Stripe Card Reader Figure 1 SLED-mPOS Overview 9 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. SLED-mPOS User Manual INTRODUCTION 1.4 Secure Touch Pinpad

(Menu/Down button) While in the SLED-mPOS menu, press this button to scroll down the selection bar. While on the main screen, press this button for 5 seconds then the SLED-mPOS will enter the SLED-mPOS menu mode. While in the SLED-mPOS menu, press this button to scroll up the selection bar.

(FN/Up button) While the SLED-mPOS waits for Alpha-Numeric key entry, this button allows the user to switch between ABC and number input mode.

(Number button) Input numbers or characters Press to finish data input.

(Enter button)

(Delete button)

(Cancel button) Press to delete the last character or number input. Press to cancel data input. 10 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. KDC User Manual APPLICATION GENERATION 2. Operating your SLED-mPOS 2.1 Basics Read NFC Tag (MIFARE) 1. The host application sends a command to enable the NFC Reader. 2. Touch NFC tag to the NFC antenna symbol on the front case, and make sure the tag and case are within 4cm of each other. 3. The SLED-mPOS will send the NFC tag UID to the host application and the user will hear a short beep if it has been read successfully. Read Magnetic-Stripe Card 1. The host application sends a command to enable the MS Card Reader. 2. Swipe MS Card either top to bottom or bottom to top. Make sure the magnetic stripe of the card face to the SLED-mPOS. 3. The SLED-mPOS will send the MS card data to the host application and the user will hear a short beep if it has been read successfully. Read IC Card 1. The host application sends a command to enable the IC Card Reader. 2. Insert IC Card to the IC Card Reader located in the left side of SLED-mPOS. Make sure the IC of the card face to up. 3. The SLED-mPOS will send the IC card data to the host application. 11 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. KDC User Manual WARRANTY 3. Warranty LIMITED WARRANTY AND DISCLAIMERS BY OPENING THE PACKAGE OF THIS PRODUCT YOU AGREE TO BECOME BOUND BY THE LIABILITY AND WARRANTY CONDITIONS AS DESCRIBED BELOW. UNDER ALL CIRCUMSTANCES, THIS MANUAL SHOULD BE READ ATTENTIVELY, BEFORE INSTALLING AND OR USING THE PRODUCT. Serial Number A serial number appears on the SLED-mPOS label. This official registration number is strictly related to the device purchased. Make sure that the serial number appearing on your SLED-

mPOS is not removed. Removing the serial number will affect the warranty conditions and liability disadvantageously, so please maintain the label with serial number on the SLED-mPOS. Units with the serial number label removed should not be operated. Warranty/Warranty Period/Liability KOAMTAC, Inc. (KOAMTAC) manufactures its hardware products in accordance with industry-

standard practices. Unless otherwise agreed in a contract, SLED-mPOS is warranted for a period of one year after purchase, covering defects in material and workmanship except rechargeable battery. KOAMTAC will repair or, at its opinion, replace products that prove to be defective in material or workmanship under proper use during the warranty period. KOAMTAC will not be liable in cases (i) in which the unit has been repaired or altered unless done or approved by KOAMTAC, (ii) in which the unit has not been maintained in accordance with any operating or handling instructions supplied by KOAMTAC, (iii) in which the unit has been subjected to unusual physical or electrical stress, misuse, abuse, power shortage, negligence or accident or

(iv) in which the unit has been used other than in accordance with the product operating and handling instructions. Preventive maintenance is the responsibility of the customer and is not covered under this warranty. Under no circumstance will KOAMTAC be liable for any direct, indirect, consequential or incidental damages arising out of use or inability to use either the hardware or software, even if KOAMTAC has been informed about the possibility of such damages. 12 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. KDC User Manual WARRANTY Warranty Coverage and Procedure During the warranty period, KOAMTAC will repair or replace defective products returned to KOAMTAC warehouse. International customers should contact the local KOAMTAC office or support center. If warranty service is required, KOAMTAC will issue a Return Material Authorization Number. Products must be shipped in the original or comparable package, shipping and insurance charges prepaid. KOAMTAC will ship the repaired or replacement product freight and insurance prepaid. Customer accepts full responsibility for its software and data including the appropriate backup thereof. Repair or replacement of a product during warranty will not extend the original warranty term. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment. 4. FCC Statement CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver. 13 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc. KDC User Manual 5. Contact Information CORPORATE HEADQUARTERS 116 Village Blvd., Suite 305 Princeton, NJ 08540, USA Phone: 609-256-4700, FAX: 609-228-4373 Email: support@koamtac.com For more information, visit our website - www.KOAMTAC.com 14 Revision 1.0 Copyright2012-2021, KOAMTAC, Inc.

AISOLUTION CO., LTD. SLED mPOS FCC ID : VH9SKXSLED-PCIEMV Model No : SKXSLED-PCIEMV Serial No : Proto type This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Manufacturer: AISOLUTION CO., LTD. Made in Korea Label Location

AISOLUTION CO., LTD. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID:

VH9SKXSLED-PCIEMV Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Part list Schematics Operational Description File Name SKXSLED-PCIEMV_Blk.pdf SKXSLED-PCIEMV_Plist.pdf SKXSLED-PCIEMV_Schem.pdf SKXSLED-PCIEMV_OpDesc.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

Exhibit Type External Photo Internal Photo Manual Test Set-up Photo File Name SKXSLED-PCIEMV_Ext Photos.pdf SKXSLED-PCIEMV_Int Photos.pdf SKXSLED-PCIEMV_Manual.pdf SKXSLED-PCIEMV_Tsup Photos For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. Sincerely, Hyun Su Cho / Assistant Manager Rev 11/20/07

AISOLUTION CO., LTD. Letter of Authorization We, the undersigned, hereby authorize In-Jung, Kim of ICR Co.,Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: VH9SKXSLED-PCIEMV including signing of all documents relating to these matters. Any and all acts carried out by In-Jung, Kim of ICR Co.,Ltd on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from AISOLUTION CO., LTD. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). May 03th, 2021 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370a Newberry, Florida 32669 USA Sincerely, Hyun Su Cho / Assistant Manager