XC-1XT SERIES Outdoor Dual Technology Intrusion Detector 40FT L X 56 W (12m x 17m) Description: XC-1XT provides unsurpassed wide area unsecured outdoor instruion detection. Combining Microwave & PIR detection technologies the XC-1XT ensures excellent coverage without nuisance alarms. Dual outputs allow the use of a single detector for annunciation and security, or allow multiple functioning via different control device assignments. Installation:
For best results install the XC-1XT at a mounting height between 6.6 ft.(2.0m) and 8.2 ft. (2.5m). Mount the unit so it is looking into an area free of obstructions, do not mount the unit so it is looking directly at heating or cooling sources. Avoid viewing operating machinery or objects which have the potential for movement. Do not aim unit so it is looking at public road / pathways. Wire the XC-1XT to the control panel device using 18 to 24 AWG standard non-shielded wire, do not run wiring parallel to AC wiring. Wiring should be in accordance with NEC, NFPA 70 for North America. Prior to re-attaching front cover to unit; Set PIR sensitivity, PulseCount, LED Enable, Detection mode, and 50/60Hz Flourescent Light immunity setting (Selectable Switch 1,2,3,4,5, and 6) as desired. If the detector is viewing a narrow area, a PC setting of 4 should be avoided, as the small area may not allow enough movement to detect intruders. A PC of 4 is best suited for a wide open detection area. For High Security applications set PIR Sensitivity to High Sensitivity =(SW1 & 2 = 120% or 100%), this allows for a quicker detection at the edge of the detection area. Animal Immunity characteristics are not available when a High Sensitivity setting is configured on the XC-1XT. Animal Immunity function is enabled by placing PIR Sensitivity at 60%. Use Microwave Sensitivity adjustment potentiometer to adjust Microwave sensitivity (Preset @ 50%). A properly adjusted MW will detect crossing movement just inside the protected area but not outside of the PIR coverage area. SW-5 allow for the selection of Dual-Technology (MW & PIR) or PIR only detection modes. A PIR only detection mode is useful when there is operating machinery or exposed fans always active within the protected area. If the installation site is subject to severe vibrations (via close proximity to railroad tracks and /or large truck movement), ensure that the mounting point is on a riged surface. In some situations it may be necessary to place a piece of plywood between the mounting surface and the XC-1XT detector to buffer wall movement. Walk-Test:
Once installation and initial setup is complete, perform a full walk test to insure that the detection parameters are met, if required make control adjustments to fine tune detection characteristics. In order to insure detection quality, the XC-1XT should be tested routinely, with no more than a one year period between tests. Control Layout and Configuration:
uW Module Do not Touch Function Select Switch SW-1 & 2 :PIR Sensitivity 120% 100% 80% 60%
OFF ON SW-1 SW-2 SW-3 SW-4 SW-5 SW-6 SW-3 Pulse Count 3 off - PC2 3 on - PC4 SW-4 LED Enable 4 off - LEDs Enabled 4 on - LEDs Disabled SW-5 Detection Mode 5 off - Dual (MW & PIR) 5 on - PIR Only SW-6 50/60 Hz 6 off - 60Hz 6 on - 50Hz PIR Detector Do not Touch 1 2 3 4 5 6 MIN. MAX. Tamper Switch Terminal Configuration TAMPER ALARM 1 ALARM 2 SPARE POWER Switch ON Switch OFF T T NC NO C NC NO C + -
LED Indicators Green = PIR Red = Alarm Amber = MW Microwave Sensitivity Adjustment The Sensitivity Adjustment allows for MW coverage to be fine set to the protected area. Preset = 50%
Max. = increases sensitivity Min. = decreases sensitivity DetectionPattern Ilustration(Standard Lens) 0 1.5 3.0 4.5 6.0 7.5 9.0 10.5 12.0 28 25 20 15 10 5 0 5 10 15 20 25 28 0 5 10 15 20 25 30 35 40 8.5 7.5 6.0 4.5 3.0 1.5 0 1.5 3.0 4.5 6.0 7.5 8.5 8.5 0
.75 1.5 3.0 4.5 6.0 7.5 9.0 10.5 12.0 Troubleshooting:
Trouble Unit does not power up. Alarm LED does not light up. Cause No or low input power. Input power polarity reversed. Remedy Apply proper input voltage. Correct wiring polarity. SW-4 is set to ON/ Disabled Detedtion Sensitivity setting incorrect. Set SW-4 to OFF. Set SW-1 &2 and/or MW range adjustment to match desired area. Pulse Count setting incorrect for area. Set SW-3 to correct PC. Alarm LED/ Relay Triggers W/O movement in the detection area LED indicates alarm, no alarm output Incorrect Sensor mounting height. Unsecured environment animals/rodents in protected area. Machinery operating in sensor view Direct sunlight/headlight in sensor view. Increase/Decrease mounting height. Block animal/rodent access. Remove the hazard / Re-aim sensor so it is not viewing hazard/machinery. Switch detection mode to Dual, add curtain/shade to block light sources. Severe vibration at mounting wall. Buffer mounting with plywood. Relocate XC-1XT mounting position. Incorrect wiring at alarm output terminals. Open circuit in wiring between detector &
control panel. Lightning damage to detector and/or control panel. Correct wiring fault. Replace/ Repair wiring. Replace damaged equipment. Rear Cover (Interior View, PCB removed)
= Six Mounting Points available. When installing this unit in a corner mount application, install screws into one side of the case. Installing screws into both sides of the case when walls are uneven causes the plastic case to become distorted thus water can be allowed entry into the unit. Exterior Wiring Channel After wiring, install the foam wiring access bug guard to prevent ingress of dust and insects. FCC Information: FCC ID: DNHXC-002-00 MODEL : XC-1XT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help. The user should not modify or change this equipment without written approval from ALEPH. Modification could void authority to use this equipment. Specifications Aleph hereby declares that the XC-1XTEU and XC-1XTUK Intrusion Detector is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at http://www.alepheurope.com/
MODEL : XC-1XTEU MODEL : XC-1XTUK
{European info here}
Testing and Maintenance:
- INSPECTION: An inspection of this unit should be made periodically, consisting of, but not limited to all mounting, wiring and the condition of the interior components.
- CLEANING: Clean the external plastic parts of this unit with a soft, damp cloth.
- TESTING: This unit should be tested routinely for proper operation. At a minimum, operation should be fully checked yearly.
- NOTES: This unit is designed to be incorporated into an overall alarm system. As it is part of the system ALEPH cannot assume responsibility for theft or damage if the system fails to operate. Power Requirements 9.5-16 VDC, 12VDC Nominal Alarm Output Current Draw 35 mA Max. Tamper Output Two Form C
(NC/NO)outputs 30 VDC/350mA Max. NC/ 30VDC/500mA Warm Up Period
<50 Seconds Operating Temperature -4F to +122F (-20C to +50C) Alarm Period LED Indicators Weight MW Detector Type 2.4 Seconds Red = Alarm Amber = Microwave Green = PIR 6.2 oz. (176 g) 10.525GHz (US and EU) 10.687GHz (UK) Humidity Limits Dimensions (H x W x D) 6.3in.(L) X 2.76in.(W) X 1.73in.(D) 95% Max. Non-condensing
(160mm x 70mm x 43.9mm) PIR Detector Type Range Stand. Lens Range Optional Lens
(Curtain) Dual Element 40ft L x 56ft W 80ft L x 8ft W PIR Sensitivity MW Range adjustment Four Adjustable Settings 60%, 80%, 100% and 120%
Adjustable via a Potentiometer Pulse Count IP Rating 2 or 4 Step Catch IP54 Mounting Height 6.6 ft (2.0m) to 8.2ft (2.5m) P/N 9-900-009-00 Rev. A In a continuing effort to improve product performance, specifications and design characteristics may be changed without prior notice. U.S. & International Patents Pending Contact Aleph Nippon Aleph Corporation
-Security Products Headquarters-
1-28-52, Komaoka, Tsurimi-ku, Yokohama-shi, Kanagawa-ken JAPAN, 230-0071 Tel: +81 045-575-4290 / Fax: +81 045-580-1676 E-mail: security@po.nippon-aleph.co.jp WEB: http://www.nippon-aleph.co.jp Aleph America Corporation 4700 Aircenter Cir, Reno, NV, 89502 USA Tel: 775 827 8000 / Fax: 775 827 8044 E-mail: info@aleph-usa.com WEB: http://www.aleph-usa.com Aleph Europe Ltd. 1 Newton Close, Park Farm Industrial Estate Wellingborough, Northamptonshire, NN8 6UW England Tel: 044 193 367 9600 / Fax: 044 193 340 1165 E-mail: info@alepheurope.com WEB: http://www.alepheurope.com