FCC ID: V3J-JB2 Jawbone Bluetooth Headset

 

FCC statement in User's Manual (for class B) Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with thi structions, may cause harmful interference to radio communications. However, ther no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution:

1.The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. 2.This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 3. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment In addition to the requirements of Section 7.1.5 in RSS-Gen, the device's shall also contain the following or equivalent statement: Privacy of communications may not be ensured when using this telephone. If privacy is provided as a standard feature, the privacy notice may be omitted provided that full justification accompanies the equipment certification application for evaluation by Industry Canada

 

 

Compliance Certification Services Inc. Internal Photo Report No.80214302 Page 2 of 13 Compliance Certification Services Inc. Report No.80214302 Page 3 of 13 Compliance Certification Services Inc. Report No.80214302 Page 4 of 13 Compliance Certification Services Inc. Report No.80214302 Page 5 of 13 Compliance Certification Services Inc. Report No.80214302 Page 6 of 13 Compliance Certification Services Inc. Report No.80214302 Page 7 of 13 Compliance Certification Services Inc. Report No.80214302 Page 8 of 13 Compliance Certification Services Inc. Report No.80214302 Page 10 of 13 Compliance Certification Services Inc. Report No.80214302 Page 11 of 13 Compliance Certification Services Inc. Report No.80214302 Page 12 of 13

 

 

Compliance Certification Services Inc. External Photo Report No.80214302 Page 1 of 13 Compliance Certification Services Inc. Power Adapter Photo Report No.80214302 Page 9 of 13 Report No.80214302 Page 13 of 13 Compliance Certification Services Inc. Cable Photo

 

 

 

 

 

 

Aliph 150 Executive Park Blvd., Ste 4550 San Francisco, CA 94134 t: 415.657.9757 f: 415.657.3172 www.jawbone.com Federal Communication Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request to delete FCC ID label location submitted on April 11, 2008 Ref: Applicant: AliphCom FCC ID: V3J-JB2 Grant Date: April 09, 2008 To Whom It May Concern:

Aliph would like to request that the FCC delete the FCC ID label format submitted on April 11, 2008. Page 2 and Page 3 of file contain detailed mechanical drawings and specifications which include sensitive and confidential information of AliphCom. Aliph acknowledges that the FCC ID label format file submitted on April 11, 2008 is available for public access since April 11, 2008. Attached is the revised single page FCC ID label format and location. Best Regards, icHard Drysdale Vice President AliphCom May 9, 2008

 

 

Aliph com 150 Executive Park Blvd. Suite 4550, San Francisco, CA94134 To whom it may concern: Date: 2008/2/26 Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 We, the undersigned, hereby authorize the Taiwan office of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS TW, to act on our behalf in all manners relating to application for equipment authorization for the Jawbone JB2_product, including signing of all documents directly and solely relating to these matters. Any and all acts carried out by CCS TW in furtherance of this purpose on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing CCS TW as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program to the extent such provisions are provided to us;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints, subject to confidentiality obligations and privilege issues;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division, except that we may retain those references and certification that may be retained, in the ordinary course of business, in connection with our disaster recovery, back-up, and archival systems and practices;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, substantially complies with the material requirements of the Certification Division;

i) keep a record of all material complaints made known to the us relating to the product compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested, subject to confidentiality obligations and privilege issues;

j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the material actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature:

REMARK:

1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us.

 

 

Statement of Compliance Letter FCC ID V3J-JB2 Product : Jawbone Model : JB2 To whom it may concern:

We, the undersigned, hereby certify that we responsible to comply with the relevant provisions of the Bluetooth 2.0 specification and certificate program as bellows:

a. Comply with the Bluetooth 2.0 technical description of the hopping sequence pseudorandom. b. Comply with the Bluetooth 2.0 technical description of each channel used equally on average. c. Comply with the Bluetooth 2.0 technical description ,the associated system receiver have a compliant input bandwidth, based on the measured 20 dB emission bandwidth. d. Comply with the Bluetooth 2.0 technical description ,the associated system receiver have the ability to hop in synchronization with the transmitter. e. The design of the frequency hopping system allow it to comply with all pertinent requirements when presented with a lengthy data stream. f. The frequency hopping system comply with the non-coordination requirement.

 

 

150 Executive Park Bivd. Suite 4550, San Francisco, CA94134 FCC ID : V3J-JB2 Model Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined Schematics Oe sOIEV eb rawl eit The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all application. Sincerely Yours, Signature:

Aliph com 150 Executive Park Bivd. Suite 4550, San Francisco, CA94134 15 Feb 2008 HYPER Taiwan Technology Inc. 7F-1, No. 92, Sec. 1, Nei-Hu Rd. Taipei, Taiwan, R.O.C. behalf in matters related to the Bluetooth Logo Certification process for Jawbone 2/ JB2 Mr. Eric Wang is the Bluetooth Qualification Body selected by Aliph com Signature

 

 

2au ELsucieco Cy agTae 20 ERCENENG LOUK BING 26-4220 er) mmatanpoue'cour parevans earzeavaes E6q6t3} Coununuiesfiou Counueeioue cojnuspys Wo stove sdnezt fo sbbjA beuwsusur sug 2H01s fot COUUReUTISIZA OU enpuUtEEEG UIG2

@Lsut D946: WbUy Oa" $008 ECC ID: Agnes eas ybbuicsus: yb cow juc:

10, MHoUu 1c WSA CoucsLU:

wee VDD monjg jK6 0 Lednicer 16 ECC beUMIZ2IOU 0 WALK SUG Jo}OMILE YIs2 92 GIEYEL beLWWSUEUT OL 2pOLE reLW CoUUASULIS|

betwaUEUs COUpgEUFIS| U/62 0 bLosect WIIbU,2 GeziBU CoUcEbsz" YUL MONIG |IKE 0 Lednezt fo WELK YU;EUUS 1W E6 OL81U9} sbbyicapou' yubp ps2 isdnezreq ecpowsric qisBLsW' pjocg qisBisw suq obeisfIoUs} qszcubsIOU 92 Te Pe VEE Cet et ee ev GE SE aE SE ee Ee ET Se ne eee ee abeciucsfiou 92 beusueus coupgeutta} L116"

zeqnb bpofoz suq nest wsunsy anayspi6 yor bnpyc scceze uce you) 03 5008"

a a a a eee

SS OS KICH Conjren pLoBLsWs pysUsBEL SEK. yout Jo soo8 ybp cow jue:

 

 

47173 Benicia Street, Fremont CA 94538 Tel: 510-771-1000, Fax: 510-661-0888 Federal Communication Commissions 7435 Oakland Mills Road Columbia MD 21046 Subject:

Ref:

Applicant: Aliph Com Inc. FCC ID: FCC ID: V3J-JB2 Grant Dated. April 09, 2008 Request to delete previous submitted file To Whom It May Concern:

Compliance Certification Services (CCS) is requesting the FCC to delete previous submitted FCC ID label format and location file from public accessible database. The specific file submitted contains device photos which Aliph would like to be blocked from public access due to marketing requirement. The specific file to be deleted:

File name: FCC ID label format and location, date submitted: April 09, 2008. Best Regards Mike Kuo / V.P. Compliance Certification Services April 11, 2008

 

 

47173 Benicia Street, Fremont CA 94538 Tel: 510-771-1000, Fax: 510-661-0888 Federal Communication Commissions 7435 Oakland Mills Road Columbia MD 21046 Subject:

Ref:

Applicant: Aliph Com FCC ID: V3J-JB2 Grant date: April 10, 2008 Request to replace one previous submitted file To Whom It May Concern:

Compliance Certification Services (CCS) is the TCB issued above grant for equipment authorization. Per applicants request and confirmation from FCC, CCS-TCB is requesting FCC to :

1. Delete the FCC ID label file uploaded on 04/11/2008 due to the file contains confidential information. 2. CCS-TCB will modify the grant condition per the confirmation from FCC. Attached is the Aliph confirmation letter to acknowledge 04/11/08 FCC ID label file can be accessible by general public since 04/11/2008. Best Regards Mike Kuo / V.P. Compliance Certification Services July 14, 2008

 

 

Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 1 of 91 FCC 47 CFR PART 15 SUBPART C AND ANSI C63.4 : 2003 TEST REPORT For Jawbone Model : JB2 Trade Name : Jawbone Issued for Aliph com 150 Executive Park Blvd. Suite 4550, San Francisco, CA94134 Issued by Compliance Certification Services Inc. Hsinchu Lab. Rm. 258, Bldg. 17, NO.195, Sec.4 Chung HsingRd., ChuTung Chen, Hsinchu, Taiwan 310, R.O.C TEL: (03) 591-0068 FAX: (03) 582-5720 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, NVLAP or any government agencies. The test results in the report only apply to the tested sample. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 2 of 91 TABLE OF CONTENTS PAGE NO. TITLE 1. TEST REPORT CERTIFICATION........................................................................................... 3 2. EUT DESCRIPTION.................................................................................................................. 4 2.1 DESCRIPTION OF EUT & POWER.................................................................................... 4 3. DESCRIPTION OF TEST MODES .......................................................................................... 5 4. TEST METHODOLOGY............................................................................................................ 6 5. FACILITIES AND ACCREDITATIONS.................................................................................. 7 5.1 FACILITIES .......................................................................................................................... 7 5.2 EQUIPMENT........................................................................................................................ 7 5.3 LABORATORY ACCREDITATIONS LISTINGS................................................................... 7 5.4 TABLE OF ACCREDITATIONS AND LISTINGS ................................................................ 8 6. CALIBRATION AND UNCERTAINTY.................................................................................... 9 6.1 MEASURING INSTRUMENT CALIBRATION..................................................................... 9 6.2 MEASUREMENT UNCERTAINTY....................................................................................... 9 7. SETUP OF EQUIPMENT UNDER TEST................................................................................ 10 8. APPLICABLE LIMITS AND TEST RESULTS ....................................................................... 11 8.1 20dB BANDWIDTH FOR HOPPING................................................................................... 11-18 8.2 MAXIMUM PEAK OUTPUT POWER ................................................................................. 19-26 8.3 HOPPING CHANNEL SEPARATION.................................................................................. 27-30 8.4 NUMBER OF HOPPING FREQUENCY USED .................................................................. 31-34 8.5 DWELL TIME ON EACH CHANNEL .................................................................................. 35-42 8.6 CONDUCTED SPURIOUS EMISSION................................................................................ 43-52 8.7 RADIATED EMISSIONS ...................................................................................................... 53 8.7.1 TRANSMITTER RADIATED SUPURIOUS EMSSIONS ................................................ 53-56 8.7.2 WORST-CASE RADIATED EMISSION BELOW 1 GHz ................................................ 57-59 8.7.3 TRANSMITTER RADIATED EMISSION ABOVE 1 GHz............................................... 60-65 8.7.4 RESTRICTED BAND EDGES ........................................................................................ 66-73 8.8 POWERLINE CONDUCTED EMISSIONS .......................................................................... 74-79 9. ANTENNA REQUIREMENT.................................................................................................... 80 9.1 STANDARD APPLICABLE................................................................................................... 80 9.2 ANTENNA CONNECTED CONSTRUCTION...................................................................... 80 APPENDIX SETUP PHOTOS....................................................................................................... 81-91 Compliance Certification Services Inc. 1. TEST REPORT CERTIFICATION FCC ID V3J-JB2 Report No.80214302-RP1 Page 3 of 91 Aliph com 150 Executive Park Blvd. Suite 4550, San Francisco, CA94134 Applicant Address Equipment Under Test Jawbone Model Trade Name Tested Date JB2 Jawbone February 14 ~ 29, 2008 APPLICABLE STANDARD STANDARD TEST RESULT FCC Part 15 Subpart C:2006 AND ANSI C63.4:2003 No non-compliance noted WE HEREBY CERTIFY THAT: The measurements shown in the attachment were made in accordance with the procedures indicated, and the energy emitted by the equipment was found to be within the limits applicable. We assume full responsibility for the accuracy and completeness of these measurements and vouch for the qualifications of all persons taking them. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 4 of 91 2. EUT DESCRIPTION 2.1 DESCRIPTION OF EUT & POWER Product Name Model Number Frequency Range Transmit Power Channel Spacing Channel Number Air Data Rate Type of Modulation Frequency Selection Transmitter Classification portable device Antenna Type Jawbone JB2 2402MHz to 2480MHz f = 2402 + nMHz, n = 0, ..78 1.66dBm 1MHz 79 Channel GFSK (1Mbps), /4-DQPSK(2Mbps), 8-DPSK(3Mbps) Frequency Hopping Spread Spectrum by software / firmware Wire Antenna, Antenna Gain : -0.57dBi Normal Mode: 3.75VDC ( From Battery Powered) Charging Mode: 5.0VDC (From Notebook PC, Powered From Host Device & Power Adapter) Since the EUT is classed portable device, and the maximum peak power is 1.66dBm (<13.6dBm), the MPE evaluation is not required and no SAR consideration applied. Power Port 1 Power Source RF Exposure Evaluation I/O Port Power Adapter :

No. Manufacturer 1 JAWBONE Model No. SPA-K901 Power Input 100V-240V, 50/60Hz Power Output 5.0V, 550mA Remark:

1. The sample selected for test was engineering sample that approximated to production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: V3J-JB2 filing to comply with Section 15.207, 15.209 and 15.247 of the FCC Part 15, Subpart C Rules. 3. For more details, please refer to the Users manual of the EUT. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 5 of 91 3. DESCRIPTION OF TEST MODES The EUT had been tested under operating condition. Radiated Emission Test (Below 1 GHz):

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Normal Linking / Charger Linking Radiated Emission Test (Above 1 GHz):

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Tested Channel Low, Mid, High Low, Mid, High Modulation Technology FHSS FHSS Modulation Type Packet Type GFSK

/4-DQPSK DH1 DH3 Bandedge Measurement :

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Tested Channel Low, High Low, High Modulation Technology FHSS FHSS Modulation Type Packet Type GFSK

/4-DQPSK DH1 DH3 Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 6 of 91 Antenna Port Conducted Measurement :

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. Tested Channel Low, Mid, High Low, Mid, High Low, Mid, High Modulation Technology FHSS FHSS FHSS Modulation Type Packet Type GFSK

/4-DQPSK 8-DPSK DH1 DH3 DH5 NoteThe field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position(X,Y axis). The worst emission was found in stand-up position (Z axis) and the worst case was recorded. 4. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 and FCC CFR 47 2.1046, 2046, 2.1047, 2.1049, 2.1051, 2.1053, 2.1055, 2.1057, 15.207, 15.209 and 15.247. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 7 of 91 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at Rm.258, Bldg.17, NO.195 , Sec. 4, Chung Hsing Rd., Chu-Tung Chen. Hsin-Chu, Taiwan 310 R.O.C. The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with preselectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, Radio Interference Measuring Apparatus and Measurement Methods. 5.3 LABORATORY ACCREDITATIONS LISTINGS The test facilities used to perform radiated and conducted emissions tests are accredited by National Voluntary Laboratory Accreditation Program for the specific scope of accreditation under Lab Code: 200118-0 to perform Electromagnetic Interference tests according to FCC PART 15 AND CISPR 22 requirements. No part of this report may be used to claim or imply product endorsement by NVLAP or any agency of the US Government. In addition, the test facilities are listed with Federal Communications Commission (registration no: 90585 and 90584). Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 8 of 91 5.4 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo USA NVLAP EN 55014-1, AS/NZS 1044, CNS 13783-1, IEC/CISPR 14-1, IEC/CISPR 22, EN 55022, EN 61000-3-2, EN 61000-3-3, ANSI C63.4, AS/NZS CISPR 22, AS/NZS 3548, IEC 61000-4-2/3/4/5/6/8/11 USA FCC 3/10 meter Open Area Test Sites to perform FCC Part 15/18 measurements Japan VCCI 3/10 meter Open Area Test Sites to perform conducted/radiated measurements Taiwan TAF FCC Method-47 CFR Part 15 Subpart C,D,E CISPR 11, FCC METHOD-47 CFR Part 18, EN 55011, CNS 13803, CISPR 13, CNS 13439, FCC Method-47 CFR Part 15 Subpart B, CISPR 14-1, EN 55014-1, CNS 13783-1, EN 55015, CNS 14115, CISPR 22, EN 55022, VCCI CNS 13438, EN 61000-4-2/3/4/5/6/8/11 Taiwan BSMI CNS 13803, CNS 13438, CNS 13439, CNS 13783-1, CNS 14115 Canada Industry Canada RSS-GEN Issue 2 200118-0 90585, 90584 R-1229/1189 C-1250/1294 SL2-IS-E-0002 SL2-IN-E-0002 SL2-A1-E-0002 SL2-R1-E-0002 SL2-R2-E-0002 SL2-L1-E-0002 IC 4417-1

* No part of this report may be used to claim or imply product endorsement by NVLAP or any agency of the US Government. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 9 of 91 6. CALIBRATION AND UNCERTAINTY 6.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment utilized to perform the tests documented in this report has been calibrated in accordance with the manufacturers recommendations, and is traceable to recognized national standards. 6.2 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the apparatus:

PARAMETER UNCERTAINTY Radiated Emission, 30 to 1000 MHz Radiated Emission, 1 to 26.5GHz Power Line Conducted Emission

+/- 3.2 dB

+/- 3.2 dB

+/- 2.1 dB Uncertainty figures are valid to a confidence level of 95%

Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 10 of 91 7. SETUP OF EQUIPMENT UNDER TEST SUPPORT EQUIPMENT Product Manufacturer Model No. Serial No. FCC ID Notebook PC Printer Mouse Modem HP HP Lenovo ZyXEL nx6130 Deskjet 948c MO28UOL Omni 56k CNU543274R CN19T6S011 44G8596 DoC DoC DoC S1Z4107727 I880MNI56K SETUP DIAGRAM FOR TESTS EUT & peripherals setup diagram is shown in appendix setup photos. No. 1 2 3 4 EUT OPERATING CONDITION 1. Setup all computers like the setup diagram. 2. Run CSR Blue Test software(ver1.24). 3. Select the following settings, Transport type: USB USB Device:csr0 4. TX mode(GFSK) TXDATA1 LO Freq: 2402, 2441, 2480 Power (EXT, Int): 255, 46 CFG PKT, Packet Type: 4 Packet Size: 27 TX mode (/4-DQPSK) TX mode (8-DPSK) TXDATA3 LO Freq: 2402, 2441, 2480 Power (EXT, Int): 255, 46 CFG PKT, Packet Type: 26 Packet Size: 367 TXDATA3 LO Freq: 2402, 2441, 2480 Power (EXT, Int): 255, 46 CFG PKT, Packet Type: 31 Packet Size: 1021 5. RX mode RXSTART1 LO Freq: 2402,2441,2480 hi-side:fales RX Attenuation :0 CFG PKT, Packet Type: 4 Packet Size: 27 6. All of the functions are under run. 7. Start test. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 11 of 91 8. APPLICABLE LIMITS AND TEST RESULTS 8.1 20dB BANDWIDTH FOR HOPPING LIMIT Limit : N/A TEST EQUIPMENT Description & Manufacturer Model No. Serial No. Date of Calibration ROHDE & SCHWARZ SPECTRUM ANALYZER FSEK30 835253/002 October 25, 2007 AGILENT SPECTRUM ANALYZER E4446A MY433601.32 June 06, 2007 TEST SETUP EUT SPECTRUM ANALYZER TEST PROCEDURE The 20dB band width was measured with a spectrum analyzer connected to RF antenna connector(conducted measurement) while EUT was operating in transmit mode at the appropriate center frequency. The analyzer center frequency was set to the EUT carrier frequency, using the analyzer. Display Line and Marker Delta functions, the 20dB band width of the emission was determined. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 12 of 91 TEST RESULTS No non-compliance noted Modulation Type: GFSK, CFG PKT Packet Type: 4 Packet Size: 27 (DH1) 20dB Bandwidth Channel Frequency Channel Low Middle High

(MHz) 2402

(kHz) 886 2441 2480 886 886 Pass / Fail N/A N/A N/A Modulation Type: /4-DQPSK, CFG PKT Packet Type: 26 Packet Size: 367 (DH3) Channel Low Middle High Channel Frequency

(MHz) 2402 20dB Bandwidth

(kHz) 1172 2441 2480 1172 1172 Modulation Type: 8-DPSK, CFG PKT Packet Type: 31 Packet Size: 1021 (DH5) Channel Frequency

(MHz) 2402 20dB Bandwidth

(kHz) 1192 2441 2480 1192 1192 Channel Low Middle High Pass / Fail N/A N/A N/A Pass / Fail N/A N/A N/A Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 13 of 91 20dB BANDWIDTH CH Low (GFSK) CH Mid (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 14 of 91 CH High (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 15 of 91 CH Low (/4-DQPSK) CH Mid (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 16 of 91 CH High (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 17 of 91 CH Low (8-DPSK) CH Mid (8-DPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 18 of 91 CH High (8-DPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 19 of 91 8.2 MAXIMUM PEAK OUTPUT POWER LIMIT 15.247(b)(1) The Maximum Peak Output Power Measurement is 125mW for frequency hopping systems operating in 2400~2483.5 MHz employing at least 15 hopping channels. TEST EQUIPMENT Description & Manufacturer Model No. Serial No. Date of Calibration ROHDE & SCHWARZ SPECTRUM ANALYZER FSEK30 835253/002 October 25, 2007 AGILENT SPECTRUM ANALYZER E4446A MY433601.32 June 06, 2007 TEST SETUP EUT SPECTRUM ANALYZER TEST PROCEDURE The RF power output was measured with a Spectrum analyzer connected to the RF Antenna connector (conducted measurement) while EUT was operating in transmit mode at the appropriate center frequency, A spectrum analyzer was used to record the shape of the transmit signal. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 20 of 91 TEST RESULTS No non-compliance noted Modulation Type: GFSK, CFG PKT Packet Type: 4 Packet Size: 27 (DH1) Channel Channel Frequency Peak Power Output Peak Power Limit

(MHz) 2402

(dBm) 1.56

(dBm) 20.97 2441 2480 1.66 1.65 20.97 20.97 1. The cable assembly insertion loss of 11dB (including 10 dB pad and 1 dB cable) was Entered as an offset in the spectrum analyzer to allow for direct reading of power. Modulation Type: /4-DQPSK, CFG PKT Packet Type: 26 Packet Size: 367 (DH3) Channel Channel Frequency Peak Power Output Peak Power Limit

(MHz) 2402

(dBm) 0.54

(dBm) 20.97 2441 2480 0.82 0.86 20.97 20.97 1. The cable assembly insertion loss of 11dB (including 10 dB pad and 1 dB cable) was Entered as an offset in the spectrum analyzer to allow for direct reading of power. Modulation Type: 8-DPSK, CFG PKT Packet Type: 31 Packet Size: 1021 (DH5) Peak Power Limit Peak Power Output Channel Channel Frequency

(MHz) 2402

(dBm) 0.67

(dBm) 20.97 2441 2480 0.97 0.99 20.97 20.97 1. The cable assembly insertion loss of 11dB (including 10 dB pad and 1 dB cable) was Entered as an offset in the spectrum analyzer to allow for direct reading of power. Low Middle High Remark:

Low Middle High Remark:

Low Middle High Remark:

Pass / Fail PASS PASS PASS Pass / Fail PASS PASS PASS Pass / Fail PASS PASS PASS Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 21 of 91 MAXIMUM PEAK OUTPUT POWER CH Low (GFSK) CH Mid (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 22 of 91 CH High (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 23 of 91 CH Low (/4-DQPSK) CH Mid (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 24 of 91 CH High (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 25 of 91 CH Low (8-DPSK) CH Mid (8-DPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 26 of 91 CH High (8-DPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 27 of 91 8.3 HOPPING CHANNEL SEPARATION LIMIT 15.247(a)(1) Frequency hopping system operating in 2400-2483.5MHz. Band may have hopping channel carrier frequencies that are separated by 25kHz or two-third of 20dB bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125mW. TEST EQUIPMENT Description & Manufacturer Model No. Serial No. Date of Calibration ROHDE & SCHWARZ SPECTRUM ANALYZER FSEK30 835253/002 October 25, 2007 AGILENT SPECTRUM ANALYZER E4446A MY433601.32 June 06, 2007 TEST SETUP EUT SPECTRUM ANALYZER TEST PROCEDURE 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT as shown in test setup without connection to measurement instrument. Turn on the EUT and connect it to measurement instrument. Then set it to any one convenient frequency within its operating range. 3. By using the MaxHold function record the separation of adjacent channels. 4. Measure the frequency difference of these two adjacent channels by spectrum analyzer MARK function. And then plot the result on spectrum analyzer screen. 5. Repeat above procedures until all frequencies measured were complete. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 28 of 91 TEST RESULTS No non-compliance noted Refer to section 8.1, 20dB bandwidth measurement, the measured channel separation should be greater than two-third of 20dB bandwidth or Minimum bandwidth. Modulation Type: GFSK, CFG PKT Packet Type: 4 Packet Size: 27 (DH1) Adjacent Hopping Channel Separation Two third of 20dB bandwidth Channel 2441MHz (Mid)

(kHz) 1004 Minimum Bandwidth Result 25 kHz PASS Modulation Type: /4-DQPSK, CFG PKT Packet Type: 26 Packet Size: 367 (DH3) Adjacent Hopping Channel Separation Two third of 20dB bandwidth Channel 2441MHz (Mid)

(kHz) 997.99 Minimum Bandwidth Result 25 kHz PASS Modulation Type: 8-DPSK, CFG PKT Packet Type: 31 Packet Size: 1021 (DH5) Minimum Bandwidth Adjacent Hopping Channel Separation Two third of 20dB bandwidth Channel Result 2441MHz (Mid)

(kHz) 1004

(kHz) 794.66 25 kHz PASS

(kHz) 590.66

(kHz) 781.33 Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 29 of 91 HOPPING CHANNEL SEPARATION CH Mid (GFSK) CH Mid (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 30 of 91 CH Mid (8-DPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 31 of 91 8.4 NUMBER OF HOPPING FREQUENCY USED LIMIT 15.247(a)(1)(iii) For frequency hopping system operating in the 2400-2483.5MHz bands shall use at least 15 hopping frequencies TEST EQUIPMENT Description & Manufacturer Model No. Serial No. Date of Calibration ROHDE & SCHWARZ SPECTRUM ANALYZER FSEK30 835253/002 October 25, 2007 AGILENT SPECTRUM ANALYZER E4446A MY433601.32 June 06, 2007 TEST SETUP EUT SPECTRUM ANALYZER TEST PROCEDURE 1 Check the calibration of the measuring instrument (spectrum analyzer) using either an internal calibrator or a known signal from an external generator. 2 Position the EUT as shown in test setup without connection to measurement instrument. Turn on the EUT and connect its antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured frequency within its operating range and make sure the instrument is operated in its linear range. 3 Set the spectrum analyzer on MaxHold Mode, and then keep the EUT in hopping mode. Record all the signals from each channel until each one has been recorded. 4 Set the spectrum analyzer on View mode and then plot the result on spectrum analyzer screen. 5 Repeat above procedures until all frequencies measured were complete. TEST RESULTS No non-compliance noted Refer to the attached plot. There are 79 hopping frequencies in a hopping sequence. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 32 of 91 NUMBER OF HOPPING FREQUENCY USED GFSK GFSK Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 33 of 91

/4-DQPSK

/4-DQPSK Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 34 of 91 8-DPSK 8-DPSK Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 35 of 91 8.5 DWELL TIME ON EACH CHANNEL LIMIT 15.247(a)(1)(iii) For frequency hopping system operating in the 2400-2483.5MHz band, the average time of occupancy on any frequency shall not be greater than 0.4 second within a 31.6 second period. TEST EQUIPMENT Description & Manufacturer Model No. Serial No. Date of Calibration ROHDE & SCHWARZ SPECTRUM ANALYZER FSEK30 835253/002 October 25, 2007 AGILENT SPECTRUM ANALYZER E4446A MY433601.32 June 06, 2007 TEST SETUP EUT SPECTRUM ANALYZER TEST PROCEDURE 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT as shown in test setup without connection to measurement instrument. Turn on the EUT and connect its antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured frequency within its operating range and make sure the instrument is operated in its linear range. 3. Adjust the center frequency of spectrum analyzer on any frequency be measured and set spectrum analyzer to zero span mode. And then, set RBW and VBW of spectrum analyzer to proper value. 4. Measure the time duration of one transmission on the measured frequency. And then plot the result with time difference of this time duration. 5. Repeat above procedures until all frequencies measured were complete. 6. The Jawbone has 3 type of payload, DH1, DH3, DH5. The hopping rate is 1600 per second. The longer the payload is, the slower the hopping rate is. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 36 of 91 TEST RESULTS No non-compliance noted Time of occupancy on the TX channel in 31.6sec = time domain slot length hop rate number of hop per channel 31.6 Refer to the attached graph. The hopping rates of Bluetooth devices change with different types of payload. The longer the payload is, the slower the hopping rate. The hopping rate scenario is defined in Bluetooth core specification. Modulation Type: GFSK, CFG PKT Packet Type: 4 Packet Size: 27 (DH1) Transmitting Frequency Packet type Dwell time

(ms) 2441MHz 2441MHz 2441MHz DH1 DH3 DH5 0.4008 1.6533 2.9058 Time of occupancy on the TX channel in 31.6sec

(ms) 128.25 264.52 309.95 Limit for Time of occupancy on the TX channel in 31.6sec

(ms) 400 400 400 DH1 Dwell time = 0.4008 ms ( 16002 ) 79 31.6 = 128.25 (ms) DH3 Dwell time = 1.6533 ms ( 16004 ) 79 31.6 = 264.52 (ms) DH5 Dwell time = 2.9058 ms ( 16006 ) 79 31.6 = 309.95 (ms) Modulation Type: /4-DQPSK, CFG PKT Packet Type: 26 Packet Size: 367 (DH3) Limit for Time of Time of occupancy on Dwell time the TX channel in occupancy on the TX channel in 31.6sec Transmitting Frequency Packet type 2441MHz 2441MHz 2441MHz DH1 DH3 DH5

(ms) 0.4008 1.6533 2.9058 31.6sec

(ms) 128.25 264.52 309.95

(ms) 400 400 400 DH1 Dwell time = 0.4008 ms ( 16002 ) 79 31.6 = 128.25 (ms) DH3 Dwell time = 1.6533 ms ( 16004 ) 79 31.6 = 264.52 (ms) DH5 Dwell time = 2.9058 ms ( 16006 ) 79 31.6 = 309.95 (ms) Modulation Type: 8-DPSK, CFG PKT Packet Type: 31 Packet Size: 1021 (DH5) Transmitting Frequency Packet type Dwell time

(ms) 2441MHz 2441MHz 2441MHz DH1 DH3 DH5 0.4008 1.6533 2.9058 Time of occupancy on the TX channel in 31.6sec

(ms) 128.25 264.52 309.95 Limit for Time of occupancy on the TX channel in 31.6sec

(ms) 400 400 400 DH1 Dwell time = 0.4008 ms ( 16002 ) 79 31.6 = 128.25 (ms) DH3 Dwell time = 1.6533 ms ( 16004 ) 79 31.6 = 264.52 (ms) DH5 Dwell time = 2.9058 ms ( 16006 ) 79 31.6 = 309.95 (ms) Results PASS PASS PASS Results PASS PASS PASS Results PASS PASS PASS Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 37 of 91 DWELL TIME ON EACH PAYLOAD DH1 CH Mid (GFSK) DH3 CH Mid (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 38 of 91 DH5 CH Mid (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 39 of 91 DH1 CH Mid (/4-DQPSK) DH3 CH Mid (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 40 of 91 DH5 CH Mid (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 41 of 91 DH1 CH Mid (8-DPSK) DH3 CH Mid (8-DPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 42 of 91 DH5 CH Mid (8-DPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 43 of 91 8.6 CONDUCTED SPURIOUS EMISSION LIMITS 15.247(d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the and that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. Attenuation below the general limits specified in 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in 15.205(a), must also comply with the radiated emission limits specified in 15.209(a) (see 15.205(c)). TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The resolution bandwidth is set to 100 kHz. The video bandwidth is set to 300 kHz. The spectrum from 30 MHz to 26.5 GHz is investigated with the transmitter set to the lowest, middle, and highest channels in the 2.4 GHz band. TEST RESULTS No non-compliance noted Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 44 of 91 BAND EDGE COMPLIANCE OF RF CONDUCTED EMISSIONS OUT-OF-BAND SPURIOUS EMISSIONS-CONDUCTED MEASUREMENT CH Low / GFSK (30MHz~3GHz) CH Low / GFSK (3GHz~26.5GHz) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 45 of 91 CH Mid / GFSK (30MHz~3GHz) CH Mid / GFSK (3GHz~26.5GHz) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 46 of 91 CH High / GFSK (30MHz~3GHz) CH High / GFSK (3GHz~26.5GHz) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 47 of 91 CH Low / /4-DQPSK (30MHz~3GHz) CH Low / /4-DQPSK (3GHz~26.5GHz) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 48 of 91 CH Mid / /4-DQPSK (30MHz~3GHz) CH Mid / /4-DQPSK (3GHz~26.5GHz) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 49 of 91 CH High / /4-DQPSK (30MHz~3GHz) CH High / /4-DQPSK (3GHz~26.5GHz) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 50 of 91 CH Low / 8-DPSK (30MHz~3GHz) CH Low / 8-DPSK(3GHz~26.5GHz) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 51 of 91 CH Mid / 8-DPSK (30MHz~3GHz) CH Mid / 8-DPSK (3GHz~26.5GHz) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 52 of 91 CH High / 8-DPSK (30MHz~3GHz) CH High / 8-DPSK (3GHz~26.5GHz) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 53 of 91 8.7 RADIATED EMISSIONS 8.7.1 TRANSMITTER RADIATED SUPURIOUS EMSSIONS LIMITS 15.205 (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below:

MHz 0.090 - 0.110 10.495 - 0.505 2.1735 - 2.1905 4.125 - 4.128 4.17725 - 4.17775 4.20725 - 4.20775 6.215 - 6.218 6.26775 - 6.26825 6.31175 - 6.31225 MHz 16.42 - 16.423 16.69475 - 16.69525 16.80425 - 16.80475 25.5 - 25.67 37.5 - 38.25 73 - 74.6 74.8 - 75.2 108 -121.94 123 - 138 8.291 - 8.294 8.362 - 8.366 149.9 - 150.05 156.52475 - 156.52525 8.37625 - 8.38675 8.41425 - 8.41475 12.29 - 12.293 12.51975 - 12.52025 12.57675 - 12.57725 13.36 - 13.41 156.7 - 156.9 162.0125 - 167.17 167.72 - 173.2 240 - 285 322 -335.4 MHz 399.9 - 410 608 - 614 960 - 1240 1300 - 1427 1435 - 1626.5 1645.5 - 1646.5 1660 -1710 1718.8 - 1722.2 2200 - 2300 2310 - 2390 2483.5 - 2500 2655 - 2900 3260 - 3267 3332 - 3339 3345.8 - 3338 3600 - 4400 GHz 4.5 - 5.15 5.35 - 5.46 7.25 - 7.75 8.025 - 8.5 9.0 - 9.2 9.3 - 9.5 10.6 -12.7 13.25 -13.4 14.47 14.5 15.35 -16.2 17.7 - 21.4 22.01 - 23.12 23.6 - 24.0 31.2 - 31.8 36.43 - 36.5

(2) 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 15.205 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown is Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 54 of 91 15.209 (a) Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table :

Field Strength

(microvolts/meter) Measurement Distance

(meters) Frequency

(MHz) 30 - 88 88 - 216 216 - 960 Above 960 100 **

150 **

200 **

500 3 3 3 3

** Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz, However, operation within these frequency bands is permitted under other sections of this Part, e-g, Sections 15.231 and 15.241. 15.209 (b) In the emission table above, the tighter limit applies at the band edges. TEST EQUIPMENT The following test equipment is utilized in making the measurements contained in this report. Manufacturer or Type Model No. Calibration Serial No. Date of CHASE BILOG ANTENNA R/S SPECTRUM ANALYZER CBL6112B 2817 FSEK30 835253/002 E4446A MY433601.32 June 06, 2007 October 16, 835418/008 Calibration December 21, October 25, 2007 2007 2007 May 07, 2007 May 16, 2007 October 18, 2007 December 25, 2007 No.2 02 10089 03077 2007 3008A01471 December 20, 2944A10052 December 24, CAL. ON USE CAL. ON USE 002 003 2007 Period Remark FINAL 1 Year 1 Year FINAL 1 Year FINAL 1 Year 1 Year 1 Year FINAL FINAL FINAL 1 Year FINAL 1 Year FINAL 1 Year FINAL 1 Year 1 Year 1 Year FINAL FINAL FINAL AGILENT SPECTRUM ANALYZER R/S EMI TEST RECEIVER OPEN SITE MIYAZAKI N TYPE COAXIAL CABLE ESCS30

----------

8D-FB Horn Antenna Horn Antenna Agilent Pre-amplifier HP Amplifier AH-118 AH-840 8449B 8447D HP High pass filter HP High pass filter 84300/80038 84300/80039 Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 55 of 91 TEST SETUP The diagram below shows the test setup that is utilized to make the measurements for emission from 30 to 1GHz. 3m EUT &

PERIPHERALS PERIPHERALS Antenna Elevation Variable The diagram below shows the test setup that is utilized to make the measurements for emission above 1GHz. 1m EUT &

PERIPHERALS Antenna Elevation Variable PERIPHERALS Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 56 of 91 TEST PROCEDURE a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 10 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. b. White measuring the radiated emission below 1GHz, the EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. White measuring the radiated emission above 1GHz, the EUT was set 1 meters away from the interference-receiving antenna c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarization of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10 dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10 dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. Note 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 KHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1 MHz for Peak detection and frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 10 Hz for Average detection (AV) at frequency above 1GHz. TEST RESULTS No non-compliance noted Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 57 of 91 8.7.2 WORST-CASE RADIATED EMISSION BELOW 1 GHz Product Name Model Name Test Mode Jawbone JB2 Test Date Test By Normal Operating Mode TEMP & Humidity 2008/02/19 Gundam Lin 21C, 76%

Antenna Factor

(dB/m) 6.60 10.20 13.64 13.90 17.46 15.72 19.80 Frequency

(MHz) 68.80 200.00 288.00 300.11 480.00 370.00 720.11 Remark:

Meter Reading at 3m(dBV) Cable Loss

(dB) Horizontal 22.30 1.10 13.20 1.90 11.70 2.25 2.30 10.20 11.80 3.04 2.65 8.30 7.70 3.86 Limits

(dBV/m) 40.00 43.50 46.00 46.00 46.00 46.00 46.00 Emission Level at 3m(dBV/m) Horizontal Vertical 32.30 26.60 29.49 28.10 32.80 27.97 32.36 30.00 25.30 27.59 26.40 32.30 26.67 31.36 Vertical 24.60 14.50 13.60 11.90 12.30 9.60 8.70 1. Emission level (dBV/m) =Antenna Factor (dB/m) + Cable loss (dB) + Meter Reading (dBV). 2. According to technical experience, all spurious emission at channel Low, Middle and High are almost the same below 1GHz, so the spurious emission test result of the channel Low was chosen as representative in finial test. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 58 of 91 Product Name Model Name Test Mode Jawbone JB2 Test Date Test By Charging Mode (From Notebook PC) TEMP & Humidity 2008/02/19 Gundam Lin 21C, 76%

Frequency

(MHz) 75.77 191.99 200.00 288.00 300.45 365.62 480.00 527.99 633.00 720.00 Antenna Factor

(dB/m) 7.12 10.04 10.20 13.64 13.91 15.61 17.46 18.06 19.20 19.80 Remark:

Meter Reading at 3m(dBV) Cable Loss

(dB) Horizontal 23.10 1.16 23.60 1.86 1.90 11.20 18.10 2.25 2.30 22.90 13.70 2.63 10.30 3.04 3.21 12.70 10.80 3.60 3.86 9.60 Limits

(dBV/m) 40.00 43.50 43.50 46.00 46.00 46.00 46.00 46.00 46.00 46.00 Emission Level at 3m(dBV/m) Horizontal Vertical 33.58 33.40 26.70 30.69 35.11 28.13 31.20 37.58 35.90 36.36 31.38 35.50 23.30 33.99 39.11 31.93 30.80 33.98 33.60 33.26 Vertical 25.30 21.50 14.60 14.80 18.90 9.90 10.70 16.30 13.10 12.70 1. Emission level (dBV/m) =Antenna Factor (dB/m) + Cable loss (dB) + Meter Reading (dBV). 2. According to technical experience, all spurious emission at channel Low, Middle and High are almost the same below 1GHz, so the spurious emission test result of the channel Low was chosen as representative in finial test. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 59 of 91 Product Name Model Name Test Mode Charging Mode (From Power Adapter) TEMP & Humidity Test Date Test By Jawbone JB2 2008/02/19 Gundam Lin 21C, 76%

Frequency

(MHz) 75.77 279.99 288.00 300.00 480.00 633.00 720.11 Antenna Factor

(dB/m) 7.12 13.46 13.64 13.90 17.46 19.20 19.80 Remark:

Meter Reading at 3m(dBV) Cable Loss

(dB) Horizontal 24.20 1.16 13.80 2.22 2.25 10.50 14.20 2.30 3.04 7.50 11.40 3.60 3.86 8.90 Limits

(dBV/m) 40.00 46.00 46.00 46.00 46.00 46.00 46.00 Emission Level at 3m(dBV/m) Horizontal Vertical 33.38 30.28 27.39 32.00 30.00 35.10 33.46 32.48 29.48 26.39 30.40 28.00 34.20 32.56 Vertical 25.10 14.60 11.50 15.80 9.50 12.30 9.80 1. Emission level (dBV/m) =Antenna Factor (dB/m) + Cable loss (dB) + Meter Reading (dBV). 2. According to technical experience, all spurious emission at channel Low, Middle and High are almost the same below 1GHz, so the spurious emission test result of the channel Low was chosen as representative in finial test. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 60 of 91 8.7.3 TRANSMITTER RADIATED EMISSION ABOVE 1 GHz Product Name Model Name Test Mode Jawbone JB2 Test Date Test By CH Low TX / GFSK TEMP & Humidity 2008/02/21 Gundam Lin 26C, 63%

Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Horizontal polarity Cable

(dB) Pre-amp

(dB) Level 1m

(dBV/m) Filter

(dB) Dist

(dB) Limit

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 52.54 1602.05 45.83 1602.05 75.51 4803.96 41.16 4803.96 50.05 6408.17 36.35 6408.17 48.83 7206.39 36.66 7206.39 47.95 9608.00 9608.00 33.73 12010.00 47.59 12010.00 34.21 27.30 27.30 34.49 34.49 36.17 36.17 39.51 39.51 40.41 40.41 41.72 41.72 3.76 3.76 6.32 6.32 7.77 7.77 8.26 8.26 9.28 9.28 10.58 10.58 36.87 36.87 36.59 36.59 36.67 36.67 36.82 36.82 37.47 37.47 36.58 36.58 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 0.00 0.00 0.37 0.37 0.28 0.28 0.93 0.93 0.53 0.53 0.45 0.45 37.23 30.52 70.59 36.24 48.10 34.40 51.21 39.04 51.20 36.98 54.25 40.87 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-36.77

-23.48

-3.41

-17.76

-25.90

-19.60

-22.79

-14.96

-22.80

-17.02

-19.75

-13.13 P A P A P A P A P A P A 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Vertical polarity Limit Cable

(dB) Pre-amp

(dB) Level 1m Filter

(dB)

(dBV/m) Dist

(dB)

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 0.00 0.00 0.37 0.37 0.28 0.28 0.93 0.93 0.53 0.53 0.45 0.45 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 36.87 36.87 36.59 36.59 36.67 36.67 36.82 36.82 37.47 37.47 36.58 36.58 3.76 3.76 6.32 6.32 7.77 7.77 8.26 8.26 9.28 9.28 10.58 10.58 27.30 27.30 34.49 34.49 36.17 36.17 39.51 39.51 40.41 40.41 41.72 41.72 60.70 1602.05 54.72 1602.05 64.36 4803.96 37.86 4803.96 50.95 6408.17 36.50 6408.17 50.02 7206.39 35.99 7206.39 47.42 9608.00 9608.00 33.61 12010.00 47.85 12010.00 34.38 Remark:

1. The measurement was searched to 10th harmonic. 2. AF: Antenna Factor, Cable: Cable Loss, Pre-Amp: Preamplifier gain, Filter: High Pass Filter Insertion Loss (3.5GHz) 3. Spectrum analyzer setting P(Peak): RBW=1MHz, VBW=1MHz, A(Average): RBW=1MHz, VBW=10Hz 4. Dist : correction to extra plate reading to 3m specification distance 1m measurement distance = -9.5dB 5. The result basic equation calculation is as follow:

-28.61

-14.59

-14.56

-21.06

-25.00

-19.45

-21.60

-15.63

-23.33

-17.14

-19.49

-12.96 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 45.39 39.41 59.44 32.94 49.00 34.55 52.40 38.37 50.67 36.86 54.51 41.04 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 P A P A P A P A P A P A Level = Reading + AF + Cable Preamp + Filter Dist, Margin = Level-Limit 6. The other emission levels were 20dB below the limit 7. The test limit distance is 3M limit. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 61 of 91 Product Name Model Name Test Mode Jawbone JB2 Test Date Test By CH Middle TX / GFSK TEMP & Humidity 2008/02/21 Gundam Lin 26C, 63%

Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Horizontal polarity Cable

(dB) Pre-amp

(dB) Level 1m

(dBV/m) Filter

(dB) Dist

(dB) Limit

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 51.88 1626.73 46.30 1626.73 75.01 4881.92 39.43 4881.92 50.55 6506.72 35.99 6506.72 51.93 7323.01 36.80 7323.01 47.43 9764.00 33.62 9764.00 12205.00 47.55 12205.00 34.11 27.49 27.49 34.61 34.61 36.34 36.34 39.62 39.62 40.29 40.29 42.03 42.03 3.80 3.80 6.32 6.32 7.93 7.93 8.30 8.30 9.57 9.57 10.52 10.52 36.85 36.85 36.61 36.61 36.72 36.72 36.94 36.94 37.59 37.59 36.48 36.48 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 0.00 0.00 0.29 0.29 0.31 0.31 0.82 0.82 0.58 0.58 0.38 0.38 36.82 31.24 70.12 34.54 48.92 34.36 54.24 39.11 50.78 36.97 54.50 41.06 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-37.18

-22.76

-3.88

-19.46

-25.08

-19.64

-19.76

-14.89

-23.22

-17.03

-19.50

-12.94 P A P A P A P A P A P A 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Vertical polarity Limit Cable

(dB) Pre-amp

(dB) Level 1m Filter

(dB)

(dBV/m) Dist

(dB)

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 0.00 0.00 0.29 0.29 0.31 0.31 0.82 0.82 0.58 0.58 0.38 0.38 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 36.85 36.85 36.61 36.61 36.72 36.72 36.94 36.94 37.59 37.59 36.48 36.48 3.80 3.80 6.32 6.32 7.93 7.93 8.30 8.30 9.57 9.57 10.52 10.52 27.49 27.49 34.61 34.61 36.34 36.34 39.62 39.62 40.29 40.29 42.03 42.03 59.96 1626.73 53.71 1626.73 64.94 4881.92 35.65 4881.92 50.61 6506.72 36.69 6506.72 51.05 7323.01 37.03 7323.01 47.30 9764.00 33.41 9764.00 12205.00 48.07 12205.00 34.22 Remark:

1. The measurement was searched to 10th harmonic. 2. AF: Antenna Factor, Cable: Cable Loss, Pre-Amp: Preamplifier gain, Filter: High Pass Filter Insertion Loss (3.5GHz) 3. Spectrum analyzer setting P(Peak): RBW=1MHz, VBW=1MHz, A(Average): RBW=1MHz, VBW=10Hz 4. Dist : correction to extra plate reading to 3m specification distance 1m measurement distance = -9.5dB 5. The result basic equation calculation is as follow:

-29.10

-15.35

-13.95

-23.24

-25.02

-18.94

-20.64

-14.66

-23.35

-17.24

-18.98

-12.83 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 44.90 38.65 60.05 30.76 48.98 35.06 53.36 39.34 50.65 36.76 55.02 41.17 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 P A P A P A P A P A P A Level = Reading + AF + Cable Preamp + Filter Dist, Margin = Level-Limit 6. The other emission levels were 20dB below the limit 7. The test limit distance is 3M limit. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 62 of 91 Product Name Model Name Test Mode Jawbone JB2 Test Date Test By CH High TX / GFSK TEMP & Humidity 2008/02/21 Gundam Lin 26C, 63%

Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Horizontal polarity Cable

(dB) Pre-amp

(dB) Level 1m

(dBV/m) Filter

(dB) Dist

(dB) Limit

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 52.68 1652.45 45.86 1652.45 75.59 4959.95 37.91 4959.95 50.99 6610.71 35.10 6610.71 52.58 7440.06 37.33 7440.06 47.91 9920.00 33.90 9920.00 12400.00 48.31 12400.00 34.83 27.69 27.69 34.74 34.74 36.96 36.96 39.74 39.74 40.16 40.16 42.34 42.34 3.84 3.84 6.32 6.32 7.99 7.99 8.35 8.35 9.87 9.87 10.46 10.46 36.83 36.83 36.63 36.63 36.69 36.69 37.07 37.07 37.72 37.72 36.39 36.39 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 0.00 0.00 0.21 0.21 0.48 0.48 0.72 0.72 0.63 0.63 0.32 0.32 37.88 31.06 70.73 33.05 50.23 34.34 54.82 39.57 51.36 37.35 55.54 42.06 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-36.12

-22.94

-3.27

-20.95

-23.77

-19.66

-19.18

-14.43

-22.64

-16.65

-18.46

-11.94 P A P A P A P A P A P A 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Vertical polarity Limit Cable

(dB) Pre-amp

(dB) Level 1m Filter

(dB)

(dBV/m) Dist

(dB)

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 0.00 0.00 0.21 0.21 0.48 0.48 0.72 0.72 0.63 0.63 0.32 0.32 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 36.83 36.83 36.63 36.63 36.69 36.69 37.07 37.07 37.72 37.72 36.39 36.39 3.84 3.84 6.32 6.32 7.99 7.99 8.35 8.35 9.87 9.87 10.46 10.46 27.69 27.69 34.74 34.74 36.96 36.96 39.74 39.74 40.16 40.16 42.34 42.34 58.05 1652.45 52.99 1652.45 65.81 4959.95 35.30 4959.95 52.46 6610.71 37.21 6610.71 52.59 7440.06 37.00 7440.06 47.73 9920.00 9920.00 33.69 12400.00 47.57 12400.00 34.25 Remark:

1. The measurement was searched to 10th harmonic. 2. AF: Antenna Factor, Cable: Cable Loss, Pre-Amp: Preamplifier gain, Filter: High Pass Filter Insertion Loss (3.5GHz) 3. Spectrum analyzer setting P(Peak): RBW=1MHz, VBW=1MHz, A(Average): RBW=1MHz, VBW=10Hz 4. Dist : correction to extra plate reading to 3m specification distance 1m measurement distance = -9.5dB 5. The result basic equation calculation is as follow:

-30.75

-15.81

-13.05

-23.56

-22.30

-17.55

-19.17

-14.76

-22.82

-16.86

-19.20

-12.52 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 43.25 38.19 60.95 30.44 51.70 36.45 54.83 39.24 51.18 37.14 54.80 41.48 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 P A P A P A P A P A P A Level = Reading + AF + Cable Preamp + Filter Dist, Margin = Level-Limit 6. The other emission levels were 20dB below the limit 7. The test limit distance is 3M limit. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 63 of 91 Product Name Model Name Test Mode Jawbone JB2 Test Date Test By CH Low TX / /4-DQPSK TEMP & Humidity 2008/02/21 Gundam Lin 26C, 63%

Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Horizontal polarity Cable

(dB) Pre-amp

(dB) Level 1m

(dBV/m) Filter

(dB) Dist

(dB) Limit

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 53.95 1602.05 46.28 1602.05 70.07 4804.00 42.93 4804.00 49.47 6407.99 38.79 6407.99 47.33 7206.00 33.71 7206.00 47.26 9608.00 33.56 9608.00 12010.00 47.58 12010.00 33.57 27.30 27.30 34.49 34.49 36.17 36.17 39.51 39.51 40.41 40.41 41.72 41.72 3.76 3.76 6.32 6.32 7.77 7.77 8.26 8.26 9.28 9.28 10.58 10.58 36.87 36.87 36.59 36.59 36.67 36.67 36.82 36.82 37.47 37.47 36.58 36.58 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 0.00 0.00 0.37 0.37 0.28 0.28 0.93 0.93 0.53 0.53 0.45 0.45 38.64 30.97 65.15 38.01 47.52 36.84 49.71 36.09 50.51 36.81 54.24 40.23 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-35.36

-23.03

-8.85

-15.99

-26.48

-17.16

-24.29

-17.91

-23.49

-17.19

-19.76

-13.77 P A P A P A P A P A P A 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Vertical polarity Limit Cable

(dB) Pre-amp

(dB) Level 1m Filter

(dB)

(dBV/m) Dist

(dB)

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 0.00 0.00 0.37 0.37 0.28 0.28 0.93 0.93 0.53 0.53 0.45 0.45 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 36.87 36.87 36.59 36.59 36.67 36.67 36.82 36.82 37.47 37.47 36.58 36.58 3.76 3.76 6.32 6.32 7.77 7.77 8.26 8.26 9.28 9.28 10.58 10.58 27.30 27.30 34.49 34.49 36.17 36.17 39.51 39.51 40.41 40.41 41.72 41.72 61.31 1602.05 57.27 1602.05 60.05 4804.00 35.58 4804.00 50.92 6407.99 41.22 6407.99 46.89 7206.00 33.22 7206.00 47.88 9608.00 33.67 9608.00 12010.00 47.76 12010.00 33.82 Remark:

1. The measurement was searched to 10th harmonic. 2. AF: Antenna Factor, Cable: Cable Loss, Pre-Amp: Preamplifier gain, Filter: High Pass Filter Insertion Loss (3.5GHz) 3. Spectrum analyzer setting P(Peak): RBW=1MHz, VBW=1MHz, A(Average): RBW=1MHz, VBW=10Hz 4. Dist : correction to extra plate reading to 3m specification distance 1m measurement distance = -9.5dB 5. The result basic equation calculation is as follow:

-28.00

-12.04

-18.87

-23.34

-25.03

-14.73

-24.73

-18.40

-22.87

-17.08

-19.58

-13.52 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 46.00 41.96 55.13 30.66 48.97 39.27 49.27 35.60 51.13 36.92 54.42 40.48 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 P A P A P A P A P A P A Level = Reading + AF + Cable Preamp + Filter Dist, Margin = Level-Limit 6. The other emission levels were 20dB below the limit 7. The test limit distance is 3M limit. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 64 of 91 Product Name Model Name Test Mode Jawbone JB2 Test Date Test By CH Middle TX / /4-DQPSK TEMP & Humidity 2008/02/21 Gundam Lin 26C, 63%

Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Horizontal polarity Cable

(dB) Pre-amp

(dB) Level 1m

(dBV/m) Filter

(dB) Dist

(dB) Limit

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 53.52 1628.10 47.75 1628.10 69.90 4882.04 37.95 4882.04 49.83 6506.81 37.35 6506.81 46.87 7323.00 33.31 7323.00 47.92 9764.00 33.52 9764.00 12205.00 47.77 12205.00 33.28 27.50 27.50 34.61 34.61 36.34 36.34 39.62 39.62 40.29 40.29 42.03 42.03 3.80 3.80 6.32 6.32 7.93 7.93 8.30 8.30 9.57 9.57 10.52 10.52 36.85 36.85 36.61 36.61 36.72 36.72 36.94 36.94 37.59 37.59 36.48 36.48 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 0.00 0.00 0.29 0.29 0.31 0.31 0.82 0.82 0.58 0.58 0.38 0.38 38.47 32.70 65.01 33.06 48.20 35.72 49.18 35.62 51.27 36.87 54.72 40.23 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-35.53

-21.30

-8.99

-20.94

-25.80

-18.28

-24.82

-18.38

-22.73

-17.13

-19.28

-13.77 P A P A P A P A P A P A 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Vertical polarity Limit Cable

(dB) Pre-amp

(dB) Level 1m Filter

(dB)

(dBV/m) Dist

(dB)

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 0.00 0.00 0.29 0.29 0.31 0.31 0.82 0.82 0.58 0.58 0.38 0.38 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 36.85 36.85 36.61 36.61 36.72 36.72 36.94 36.94 37.59 37.59 36.48 36.48 3.80 3.80 6.32 6.32 7.93 7.93 8.30 8.30 9.57 9.57 10.52 10.52 27.50 27.50 34.61 34.61 36.34 36.34 39.62 39.62 40.29 40.29 42.03 42.03 60.88 1628.10 57.45 1628.10 60.92 4882.04 33.63 4882.04 50.98 6506.81 41.01 6506.81 47.52 7323.00 33.36 7323.00 47.41 9764.00 33.06 9764.00 12205.00 48.01 12205.00 33.78 Remark:

1. The measurement was searched to 10th harmonic. 2. AF: Antenna Factor, Cable: Cable Loss, Pre-Amp: Preamplifier gain, Filter: High Pass Filter Insertion Loss (3.5GHz) 3. Spectrum analyzer setting P(Peak): RBW=1MHz, VBW=1MHz, A(Average): RBW=1MHz, VBW=10Hz 4. Dist : correction to extra plate reading to 3m specification distance 1m measurement distance = -9.5dB 5. The result basic equation calculation is as follow:

-28.17

-11.60

-17.97

-25.26

-24.65

-14.62

-24.17

-18.33

-23.24

-17.59

-19.04

-13.27 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 45.83 42.40 56.03 28.74 49.35 39.38 49.83 35.67 50.76 36.41 54.96 40.73 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 P A P A P A P A P A P A Level = Reading + AF + Cable Preamp + Filter Dist, Margin = Level-Limit 6. The other emission levels were 20dB below the limit 7. The test limit distance is 3M limit. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 65 of 91 Product Name Model Name Test Mode Jawbone JB2 Test Date Test By CH High TX / /4-DQPSK TEMP & Humidity 2008/02/21 Gundam Lin 26C, 63%

Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Horizontal polarity Cable

(dB) Pre-amp

(dB) Level 1m

(dBV/m) Filter

(dB) Dist

(dB) Limit

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 52.23 1652.81 47.92 1652.81 70.18 4960.08 35.77 4960.08 49.19 6610.55 36.29 6610.55 47.47 7440.00 34.12 7440.00 47.32 9920.00 33.67 9920.00 12400.00 48.43 12400.00 34.02 27.69 27.69 34.74 34.74 36.96 36.96 39.74 39.74 40.16 40.16 42.34 42.34 3.84 3.84 6.32 6.32 7.99 7.99 8.35 8.35 9.87 9.87 10.46 10.46 36.83 36.83 36.63 36.63 36.69 36.69 37.07 37.07 37.72 37.72 36.39 36.39 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 0.00 0.00 0.21 0.21 0.48 0.48 0.72 0.72 0.63 0.63 0.32 0.32 37.44 33.13 65.32 30.91 48.43 35.53 49.71 36.36 50.77 37.12 55.66 41.25 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-36.56

-20.87

-8.68

-23.09

-25.57

-18.47

-24.29

-17.64

-23.23

-16.88

-18.34

-12.75 P A P A P A P A P A P A 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 Freq.

(MHz) Reading

(dBV) AF

(dBV) Measurement Distance at 1m Vertical polarity Limit Cable

(dB) Pre-amp

(dB) Level 1m Filter

(dB)

(dBV/m) Dist

(dB)

(dBV/m) Margin

(dB) Mark

(P/Q/A) Height

(Meter) 0.00 0.00 0.21 0.21 0.48 0.48 0.72 0.72 0.63 0.63 0.32 0.32 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 9.50 36.83 36.83 36.63 36.63 36.69 36.69 37.07 37.07 37.72 37.72 36.39 36.39 3.84 3.84 6.32 6.32 7.99 7.99 8.35 8.35 9.87 9.87 10.46 10.46 27.69 27.69 34.74 34.74 36.96 36.96 39.74 39.74 40.16 40.16 42.34 42.34 59.71 1652.81 54.65 1652.81 60.63 4960.08 34.15 4960.08 51.00 6610.55 41.40 6610.55 47.45 7440.00 33.90 7440.00 46.97 9920.00 9920.00 33.26 12400.00 47.52 12400.00 33.74 Remark:

1. The measurement was searched to 10th harmonic. 2. AF: Antenna Factor, Cable: Cable Loss, Pre-Amp: Preamplifier gain, Filter: High Pass Filter Insertion Loss (3.5GHz) 3. Spectrum analyzer setting P(Peak): RBW=1MHz, VBW=1MHz, A(Average): RBW=1MHz, VBW=10Hz 4. Dist : correction to extra plate reading to 3m specification distance 1m measurement distance = -9.5dB 5. The result basic equation calculation is as follow:

-29.08

-14.14

-18.23

-24.71

-23.76

-13.36

-24.31

-17.86

-23.58

-17.29

-19.25

-13.03 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 44.92 39.86 55.77 29.29 50.24 40.64 49.69 36.14 50.42 36.71 54.75 40.97 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 P A P A P A P A P A P A Level = Reading + AF + Cable Preamp + Filter Dist, Margin = Level-Limit 6. The other emission levels were 20dB below the limit 7. The test limit distance is 3M limit. Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 66 of 91 8.7.4 RESTRICTED BAND EDGES Detector mode : Peak Polarity : Horizontal CH Low (GFSK) Detector mode : Average Polarity : Horizontal CH Low (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 67 of 91 Detector mode : Peak Polarity : Vertical CH Low (GFSK) Detector mode : Average Polarity : Vertical CH Low (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 68 of 91 Detector mode : Peak Polarity : Horizontal CH High (GFSK) Detector mode : Average Polarity : Horizontal CH High (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 69 of 91 Detector mode : Peak Polarity : Vertical CH High (GFSK) Detector mode : Average Polarity : Vertical CH High (GFSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 70 of 91 Detector mode : Peak Polarity : Horizontal CH Low (/4-DQPSK) Detector mode : Average Polarity : Horizontal CH Low (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 71 of 91 Detector mode : Peak Polarity : Vertical CH Low (/4-DQPSK) Detector mode : Average Polarity : Vertical CH Low (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 72 of 91 Detector mode : Peak Polarity : Horizontal CH High (/4-DQPSK) Detector mode : Average Polarity : Horizontal CH High (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 73 of 91 Detector mode : Peak Polarity : Vertical CH High (/4-DQPSK) Detector mode : Average Polarity : Vertical CH High (/4-DQPSK) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 74 of 91 8.8 POWERLINE CONDUCTED EMISSIONS LIMITS 15.207 (a) Except as shown in paragraph (b) and (c) this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 H/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Frequency of Emission (MHz) Conducted limit (dBv) 0.15 - 0.5 0.5 - 5 5 - 30 Quasi-peak 66 to 56 56 60 Average 56 to 46 46 50 TEST EQUIPMENT The following test equipment is used during the conducted powerline tests Manufacturer or Type Model No. Serial No. Date of Calibration Calibration Period Remark SCHWARZBECK L.I.S.N SCHWARZBECK L.I.S.N R & S TEST RECEIVER KEENE SHIELDED ROOM NSLK 8127 8127-465 July 09, 2007 1 Year FINAL NSLK 8127 8127-473 October 04, 2007 1 Year FINAL ESHS30 838550/003 January 23, 2008 1 Year FINAL 5983 No.1 N/A N/A FINAL R & S PULSE LIMIT ESH3-Z2 10117 BELDEN N TYPE COAXIAL CABLE 8268 M17/164 003 September 17, 2007 September 14, 2007 1 Year FINAL 1 Year FINAL Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 75 of 91 TEST SETUP 120VAC 60Hz L.I.S.N. POWERLINE of PERIPHERALS POWERLINE of EUT L.I.S.N. 120VAC 60Hz EUT &

PERIPHERALS 120VAC 60Hz ISOLATE TRANSFORMER SPECTRUM ANALYZER

/TEST RECEIVER TEST PROCEDURE The EUT is placed on a non-conducting table 40 cm from the vertical ground plane and 80cm above the horizontal ground plane. The EUT IS CONFIGURED IN ACCORDANCE WITH ANSI C63.4. The resolution bandwidth is set to 9 kHz for both quasi-peak detection and average detection measurements. Line conducted data is recorded for both NEUTRAL and LINE. TEST RESULTS No non-compliance noted Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 76 of 91 CONDUCTED RF VOLTAGE MEASUREMENT Jawbone 2008/02/18 Gundam Lin Charging Mode (From Notebook PC) TEMP & Humidity 24.5C, 65%

Test Date Test By JB2 Product Name Model Test Mode LINE Remark:

1. Correction Factor = Insertion loss + cable loss 2. Margin value = Emission level Limit value Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 77 of 91 Product Name Model Test Mode NEUTRAL Jawbone 2008/02/18 Gundam Lin Charging Mode (From Notebook PC) TEMP & Humidity 24.5C, 65%

Test Date Test By JB2 Remark:

1. Correction Factor = Insertion loss + cable loss 2. Margin value = Emission level Limit value Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 78 of 91 Product Name 2008/02/18 Gundam Lin Test Mode Charging Mode (From Power Adapter) TEMP & Humidity 24.5C, 65%

Test Date Test By Jawbone Model JB2 LINE Remark:

1. Correction Factor = Insertion loss + cable loss 2. Margin value = Emission level Limit value Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 79 of 91 Product Name 2008/02/18 Gundam Lin Test Mode Charging Mode (From Power Adapter) TEMP & Humidity 24.5C, 65%

Test Date Test By Jawbone Model JB2 NEUTRAL Remark:

1. Correction Factor = Insertion loss + cable loss 2. Margin value = Emission level Limit value Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 80 of 91 9. ANTENNA REQUIREMENT 9.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 9.2 ANTENNA CONNECTED CONSTRUCTION The antenna used in this product is Wire antenna. The maximum gain of the antenna only

-0.57dBi.

 

 

Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 81 of 91 APPENDIX SETUP PHOTOS RADIATED MEASUREMENT SETUP Normal Operating Mode Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 82 of 91 Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 83 of 91 Charging Mode (From Notebook PC) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 84 of 91 Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 85 of 91 Charging Mode (From Power Adapter) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 86 of 91 Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 87 of 91 RADIATED RF MEASUREMENT SETUP Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 88 of 91 Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 89 of 91 RF PORT COUNTED MEASURE SETUP Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 90 of 91 POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP Charging Mode (From Notebook PC) Compliance Certification Services Inc. FCC ID V3J-JB2 Report No.80214302-RP1 Page 91 of 91 Charging Mode (From Power Adapter)