FCC ID: RSL-TQ6602 802.11ax 4x4+4x4 dual-radio 2.4G/5G wireless AP

TQ6602 Enterprise-class 802.11ax Indoor Wireless Access Point with 2.4GHz and 5GHz Radios Installation Guide 613-002891 Rev. A Review Draft - August 12, 2020 Copyright 2020 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages. Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Electrical Safety and Emissions Standards This product meets the following standards:

Federal Communications Commission Interference Statement European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment on page 4 Safety and Electromagnetic Emissions on page 4 Translated Safety Statements on page 8 Federal Communications Commission Interference Statement Declaration of Conformity Manufacturer Name: Allied Telesis Declares that the product: 802.11a/b/g/n/ac/ax wave2 dual radio 2.4G (4x4) and 5G (4x4) wireless access point Model Number: TQ6602 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3 Review Draft - August 12, 2020 Caution FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Avertissement Avertissement de la FCC: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. E80 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Allied Telesis ensures RoHS conformance by requiring supplier Declarations of Conformity, monitoring incoming materials, and maintaining manufacturing process controls. Note For additional regulatory statements, refer to Appendix B, Regulatory Statements on page 75. Safety and Electromagnetic Emissions Standard Compliance RoHs compliant European Union RoHS (Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.) 4 Review Draft - August 12, 2020 Wire Communication IEEE 802.1 IEEE 802.3 IEEE 802.3u IEEE 802.3z IEEE 802.3ab IEEE 802.3bz IEEE 802.3x IEEE 802.3at ITU-T G.993.1 Wireless LAN Communication IEEE 802.11 DSSS IEEE 802.11a OFDM IEEE 802.11b DSSS/FHSS IEEE 802.11g OFDM IEEE 802.11n OFDM IEEE 802.11ac OFDM IEEE 802.11ax OFDMA Safety CB/UL TUV AEL EN62368-1 (Co-license) Class I, US FDA/CDRH EN(IEC) 60825-1:1994+a11, EN(IEC) 60825-2:1994 EN(IEC) 60950: 1992+A1+A2+A3 UL2043 IEC 62368-1: 2014 and EN62368-1: 2014 UL 62368-1: 2nd Edition, 2014-12-01 CSA C22.2 No. 62368-1-14, 2nd Edition, 2014-12-01 TQ6602 Wireless Access Point Installation Guide 5 Review Draft - August 12, 2020 Electro Magnetic Interference (EMI) FCC part15 Subpart B/ Class B EN55032 Class B VCCI-CISPR 32 / Class B AS/NZS CISPR 32 Electro Magnetic Susceptibility (EMS) - EN55024 and EN55035 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6

(IEC 61000-4-8 IEC 61000-4-11 IEC 61000-3-2 IEC 61000-3-3 47 CFR Part15, subpart C 47 CFR Part15, subpart E FCC DFS CE RED Directive 2014/53/EU EN55032 EN 55024 EN 301489-1 V2.1.1 EN 301489-17 V3.1.1 EN 300328 V2.2.2 EN 301893 V2.1.1 EN 62311 / EN 50385 European Council Directive 2014/30/EU DFS EN 55035 EN 60601-1-2 6 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide RCM IC AS/NZS CISPR 32 AS/NZS 4268 ICES-003 issue 6 RSS-102 RSS-247 issue 2 Japan JATE ARIB STD-T66 ARIB STD-T71 Hong Kong OFCA India WPC Malaysia SIRIM Taiwan BSMI & NCC CNS 13438 CNS 14336-1

(LP002) Thailand NBTC Vietnam MIC China SRRC Singapore IMDA TS SRD Complies with IMDA Standards DB102434 Figure 1. Singapore IMDA Logo 7 Review Draft - August 12, 2020 Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements on the Allied Telesis website at www.alliedtelesis.com/library. Remarque: Les consignes de scurit portant le symbole sont traduites dans plusieurs langues dans le document Translated Safety Statements, disponible l'adresse www.alliedtelesis.com/

library. 8 Review Draft - August 12, 2020 Contents Electrical Safety and Emissions Standards .................................................................................................. 3 Preface ............................................................................................................................................................15 Safety Symbols Used in this Document .......................................................................................................... 16 Contacting Allied Telesis ................................................................................................................................. 17 Chapter 1: Product Description ...................................................................................................................19 Features ........................................................................................................................................................... 20 Hardware Components..................................................................................................................................... 23 Ethernet LAN Port ............................................................................................................................................ 25 Power Over Ethernet.................................................................................................................................. 25 Connector Type.......................................................................................................................................... 25 Speed......................................................................................................................................................... 25 Duplex Mode .............................................................................................................................................. 26 Automatic MDIX Detection ......................................................................................................................... 26 Cable Requirements .................................................................................................................................. 27 Maximum Distance..................................................................................................................................... 27 Port Pinouts................................................................................................................................................ 27 How to Power the Wireless Access Point......................................................................................................... 28 External AC/DC Power Adapter ................................................................................................................. 28 PoE+ Power Source................................................................................................................................... 28 Both AC/DC Power Adapter and PoE Power Source ................................................................................ 29 DC Connector for an External AC/DC Power Adapter ..................................................................................... 30 POWER On/Off Button ..................................................................................................................................... 31 LEDs................................................................................................................................................................. 32 Reset Button..................................................................................................................................................... 34 Management Tools........................................................................................................................................... 35 Web Browser.............................................................................................................................................. 35 Vista Manager EX and AWC Plug-in.......................................................................................................... 35 SNMP......................................................................................................................................................... 35 Chapter 2: Beginning the Installation ..........................................................................................................37 Reviewing Safety Precautions.......................................................................................................................... 38 Choosing a Site for the Wireless Access Point ................................................................................................ 41 Unpacking the Shipping Box ............................................................................................................................ 42 Chapter 3: Installing the Wireless Access Point ........................................................................................43 Installing the Wireless Access Point on a Table............................................................................................... 44 Overview to Installing the Wireless Access Point on a Wall or Ceiling............................................................. 48 Installing the Mounting Bracket on a Wall or Ceiling ........................................................................................ 51 Installing the Mounting Bracket Screws............................................................................................................ 55 Connecting an Ethernet Cable to the Ethernet LAN Port ................................................................................. 56 Connecting the AC/DC Power Adapter ............................................................................................................ 57 Attaching the Wireless Access Point to the Wall Mounting Bracket ................................................................. 59 Installing an Anti-theft Device ........................................................................................................................... 61 Chapter 4: Managing the Wireless Access Point .......................................................................................63 Starting the First Management Session Without a DHCP Server .................................................................... 64 Starting the First Management Session with a Direct Connection ............................................................. 65 9 Review Draft - August 12, 2020 Contents Starting the First Management Session Over a Network ...........................................................................65 Starting a Management Session ....................................................................................................................... 67 Appendix A: Technical Specifications ........................................................................................................ 69 Physical Specifications ..................................................................................................................................... 69 Environmental Specifications ............................................................................................................................ 69 Power Specifications......................................................................................................................................... 70 Input Power Specifications ......................................................................................................................... 70 External AC/DC Power Adapter Specifications .......................................................................................... 70 PoE+ Power Requirements ........................................................................................................................ 70 Cable Specifications ......................................................................................................................................... 71 LAN Ports Specifications and Pinouts .............................................................................................................. 72 Port Specifications...................................................................................................................................... 72 Port Pinouts ................................................................................................................................................ 72 Appendix B: Regulatory Statements ........................................................................................................... 75 Federal Communication Commission Interference Statement.......................................................................... 76 Industry Canada Statement .............................................................................................................................. 78 Europe - EU Declaration of Conformity............................................................................................................. 80 Operating Frequencies and Maximum Transmission Power Levels .......................................................... 80 Radiation Exposure Statement................................................................................................................... 80 Importer ...................................................................................................................................................... 80 Appendix C: Radiation Patterns .................................................................................................................. 81 2.4GHz Antenna 1 ............................................................................................................................................ 82 2.4GHz Antenna 2 ............................................................................................................................................ 83 2.4GHz Antenna 3 ............................................................................................................................................ 84 2.4GHz Antenna 4 ............................................................................................................................................ 85 5GHz Antenna 1 ............................................................................................................................................... 86 5GHz Antenna 2 ............................................................................................................................................... 87 5GHz Antenna 3 ............................................................................................................................................... 88 5GHz Antenna 4 ............................................................................................................................................... 89 10 Review Draft - August 12, 2020 Figures Figure 1: Singapore IMDA Logo ........................................................................................................................ 7 Figure 2: Top View .......................................................................................................................................... 23 Figure 3: Front Panel....................................................................................................................................... 24 Figure 4: Rear Panel ....................................................................................................................................... 24 Figure 5: Powering the Access Point with an AC/DC Power Adapter ............................................................. 28 Figure 6: Powering the Access Point with a PoE Power Source..................................................................... 28 Figure 7: Powering the Access Point with Both an External AC/DC Adapter and a PoE+ Power Source ...... 29 Figure 8: PWRADP-01 Power Adapter............................................................................................................ 30 Figure 9: Shipping Box Contents..................................................................................................................... 42 Figure 10: TQ6602 Wireless Access Point on a Table.................................................................................... 44 Figure 11: Installing the Bracket Screws ......................................................................................................... 45 Figure 12: Panel Screws ................................................................................................................................. 45 Figure 13: Installing the Mounting Bracket ...................................................................................................... 46 Figure 14: Tightening Bracket Retaining Screw .............................................................................................. 46 Figure 15: Orientations of the TQ6602 Wireless Access Point on a Wall ....................................................... 48 Figure 16: Invalid Position of the TQ6602 Wireless Access Point on a Wall................................................... 48 Figure 17: TQ6602 Wireless Access Point on the Ceiling............................................................................... 49 Figure 18: Marking the Holes for the Key-Hole Slots ...................................................................................... 51 Figure 19: Installing Two Screws..................................................................................................................... 52 Figure 20: Installing the Wall Mounting Bracket On the Screws...................................................................... 53 Figure 21: Pre-Drill Holes on Wall Mounting Bracket ...................................................................................... 53 Figure 22: Securing the Wall Mounting Bracket .............................................................................................. 54 Figure 23: Installing the Bracket Screws into the Wireless Access Point........................................................ 55 Figure 24: Connecting an Ethernet Cable to the LAN Port.............................................................................. 56 Figure 25: Connecting the AC Power Cord to the PWRADP-01 Power Adapter ............................................ 57 Figure 26: Connecting an AC/DC Power Adapter to the DC IN Connector..................................................... 57 Figure 27: Connecting the Power Cord on the PWRADP-01 Power Adapter to an AC Source ...................... 58 Figure 28: DC Power On/Off Button ................................................................................................................ 58 Figure 29: Installing the Wireless Access Point on the Wall Mounting Bracket............................................... 59 Figure 30: Seating the Wireless Access Point on the Wall Mounting Bracket................................................. 60 Figure 31: Tightening the Wall Mounting Bracket Thumbscrew ...................................................................... 60 Figure 32: Kensington Lock Port ..................................................................................................................... 61 Figure 33: Log On Window.............................................................................................................................. 67 Figure 34: Pin Layout for RJ45 Connector on the Ethernet Port ..................................................................... 72 Figure 35: Axes on the TQ6602 Access Point................................................................................................. 81 11 Review Draft - August 12, 2020 List of Figures 12 Review Draft - August 12, 2020 Tables Table 1. LED Status Information .................................................................................................................... 32 Table 2. Physical Specifications ..................................................................................................................... 69 Table 3. Environmental Specifications ........................................................................................................... 69 Table 4. Input Power Specifications ............................................................................................................... 70 Table 5. External AC/DC Power Adapter Specifications ................................................................................ 70 Table 6. PoE Power Requirements on the Ethernet Port ............................................................................... 70 Table 7. LAN Port Specifications .................................................................................................................... 72 Table 8. MDI Pin Signals at 10/100Mbps ....................................................................................................... 72 Table 9. MDIX Pin Signals at 10/100Mbps ..................................................................................................... 73 Table 10. Connector Pinouts at 1/2.5/5Gbps ................................................................................................. 73 13 Review Draft - August 12, 2020 List of Tables 14 Review Draft - August 12, 2020 Preface This guide contains the hardware installation instructions for the indoor IEEE802.11ax TQ6602 Wireless Access Point. The preface contains the following sections:

Safety Symbols Used in this Document on page 16 Contacting Allied Telesis on page 17 15 Review Draft - August 12, 2020 Preface Safety Symbols Used in this Document This document uses the following conventions. Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a specific action may result in bodily injury. Warning Warnings inform you of hot surfaces. 16 Review Draft - August 12, 2020 Contacting Allied Telesis TQ6602 Wireless Access Point Installation Guide For assistance with this product, you can contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/support. You can find links for the following services on this page:

24/7 Online Support Enter our interactive support center to search for answers to your product questions in our knowledge database, check support tickets, learn about Return Merchandise Authorizations

(RMAs), and contact Allied Telesis technical experts. USA and EMEA phone support Select the phone number that best fits your location and customer type. Hardware warranty information Learn about Allied Telesis warranties and register your product online. Replacement Services Submit an RMA request via our interactive support center. Documentation View the most recent installation and user guides, software release notes, white papers, and data sheets for your products. Software Downloads Download the latest software releases for your managed products. For sales or corporate information, go to www.alliedtelesis.com/

purchase. 17 Review Draft - August 12, 2020 Preface 18 Review Draft - August 12, 2020 Chapter 1 Product Description The sections in this chapter describe the hardware components of the 802.11ax TQ6602 Wireless Access Point:

How to Power the Wireless Access Point on page 28 DC Connector for an External AC/DC Power Adapter on page 30 Features on page 20 Hardware Components on page 23 Ethernet LAN Port on page 25 POWER On/Off Button on page 31 LEDs on page 32 Reset Button on page 34 Management Tools on page 35 19 Review Draft - August 12, 2020 Chapter 1: Product Description Features 20 Hardware features include:

One 2.4GHz radio One 5GHz radio 4x4 MU-MIMO 2.4GHz Internal antennas 4x4 MU-MIMO 5GHz Internal antennas Transmission beamforming One 10/100Mbps/1/2.5/5Gbps Ethernet LAN port with RJ-45 IEEE 802.3at PoE+ Class 4 powered device One Reset button for rebooting the unit or restoring the default One On/Off button for the AC/DC power adapter connector LEDs for the 2.4GHz and 5GHz radios, Ethernet LAN port, and connector settings power Ceiling, wall, or table installation Kensington lock port One Console RJ-45 port for factory use only Software features include:

IEEE802.11a/b/g/n/ac/ax Multi-channel (cell operation) Channel Blankets (single-channel operation) Multi-channel and Channel Blanket hybrid operation Orthogonal Frequency Division Multiple Access (OFDMA) Manual or automatic radio channel selection Sixteen virtual access points (VAPs) per radio and thirty-two VAPs per access point Quality of Service (QoS) ingress and egress queues Fast roaming (IEEE 802.11v/k/r) Control of radio transmission power Dynamic frequency selection Band steering WiFi multimedia (WMM) for prioritizing traffic Client filtering by MAC addresses Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Wireless Distribution System (WDS) bridges Dynamic Host Control Protocol (DHCP) client Network Time Protocol (NTP) client System log Syslog client Autonomous Management Framework (AMF) Guest node Security and encryption include:

Open system Shared key authentication Static WEP with 64/128/256 bit encryption (IEEE 802.11a/b/g only) WPA Personal or Enterprise security with auto, CCMP (AES), or WPA2 Personal or Enterprise security with auto, CCMP (AES), or WPA3 Personal or Enterprise security with CCMP (AES/CNSA) TKIP encryption TKIP encryption encryption Frequency range and bandwidth for the 2.4GHz radio include:

Frequency range and bandwidth for the 5GHz radio include:

2.412 to 2.484GHz 20/40MHz 5.150 to 5.850GHz 20/40/80/80+80MHz Features of the Ethernet LAN port include:

10Mbps (IEEE 802.3), 100Mbps (IEEE 802.3u), 1000Mbps (IEEE 802.3ab), 2.5Gbps, and 5Gbps (IEEE 802.3bz) PoE+ (IEEE 802.3at) Flow control (IEEE 802.3x) VLAN tagging (IEEE 802.1Q) Auto-Negotiation for speed and duplex mode Auto-MDI/MDIX at 10/100Mbps Management options include:

On-board web browser management interface Vista Manager EX with Automous Wave Controller (AWC) plug-in or AWC lite plug-in 21 Review Draft - August 12, 2020 Chapter 1: Product Description Autonomous Management Framework (AMF) Security or Security Mini (AMF-Sec mini) SNMPv1 and v2c Note For a complete list of features, refer to the TQ6602 Wireless Access Point User Guide or the products data sheet. 22 Review Draft - August 12, 2020 Hardware Components TQ6602 Wireless Access Point Installation Guide The top view of the TQ6602 Wireless Access Point is illustrated in Figure 1. Back Edge Front Edge LAN (PoE) Port LED 2.4GHz Radio LED PWR/SYS (Power/

System) LED 5GHz Radio LED Figure 1. Top View 23 Review Draft - August 12, 2020 Chapter 1: Product Description The front panel is illustrated in Figure 2. Mounting Bracket Thumbscrew Hole Figure 2. Front Panel The rear panel is shown in Figure 3. Kensington Lock Port Reset Button Ethernet LAN PoE+ Port POWER On/Off Button for DC IN Connector Console Serial Port DC IN Connector for AC/DC Adapter Figure 3. Rear Panel Note The Console Serial port is for manufacturing purposes only. 24 Review Draft - August 12, 2020 Ethernet LAN Port TQ6602 Wireless Access Point Installation Guide The wireless access point has one Ethernet LAN port on the rear panel, with these operational properties:

10Mbps (IEEE 802.3), 100Mbps (IEEE 802.3u), 1000Mbps (IEEE 802.3ab), 2.5Gbps, and 5Gbps (IEEE 802.3bz) Flow control (IEEE 802.3x) VLAN tagging (IEEE 802.1Q) Auto-Negotiation for speed and duplex mode Auto-MDI/MDIX at 10/100Mbps The port has the following functions:

You use it to connect the wireless access point to a device on your wired network, such as Ethernet switch or router. The port makes it possible for wireless clients of the wireless network to gain access to the wired network. The Ethernet LAN port can also be used to provide the electrical power to the device. The wireless access point is a PoE powered device, meaning it can be powered by a PoE power source on the port. A PoE power source can be a PoE router or switch. such as the x320-10GH Switch from Allied Telesis. Electrical power is transmitted to the wireless access point by the power source over the same network cable that carries the network traffic. Power Over Ethernet You can power the wireless access point as a PoE+ Class 4 device on the LAN port. Powering the device with PoE requires connecting the LAN port to a PoE source device. You can also power the device with an external AC/DC adapter, such as the PWRADP-01 (DA-48Z12) Power Adapter. Refer to How to Power the Wireless Access Point on page 28. Connector Type The LAN port has an eight-pin RJ45 connector. The port uses four pins in the connector at 10/100 Mbps and all eight pins at higher speeds. Refer to the tables in Port Pinouts on page 72 for the pin assignments. Speed The LAN port can operate at 10/100Mbps/1/2.5/5Gbps. The speed is set automatically with Auto-Negotiation. You cannot disable Auto-Negotiation on the port. 25 Review Draft - August 12, 2020 Chapter 1: Product Description Note You should connect the LAN port to a network device that also supports Auto-Negotiation. The LAN port operates at 10Mbps if it is connected to a network device does not support Auto-Negotiation. This may result in reduced network performance. Duplex Mode The LAN port can operate in either half- or full-duplex mode at 10/100Mbps, and full-duplex mode at higher speeds. The port is IEEE 802.3u-compliant and uses Auto-Negotiation to set the duplex mode. You cannot disable Auto-Negotiation on the port. Note You should connect the LAN port to a network device that also supports Auto-Negotiation for duplex mode. If connected to a network device that does not support Auto-Negotiation, it operates at half-duplex mode. This will result in a duplex mode mismatch if the network device is operating at full duplex. This may result in reduced network performance. Automatic MDIX Detection The LAN port is IEEE 802.3ab compliant. It features automatic MDIX detection when operating at 10/100Mbps. (Automatic MDIX detection does not apply to higher speeds.) This feature automatically configures the port to MDI or MDIX depending on the wiring configuration of the port on the network device where it is connected. You cannot disable automatic MDIX detection. For automatic MDIX detection to work properly, this feature must also be present on the network device. The LAN port defaults to MDIX if it is connected to a network device that does not support automatic MDIX detection. 26 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Cable Requirements Maximum Distance Port Pinouts The minimum cable requirements for the port are listed here. 10/100 Mbps: Standard TIA/EIA 568-B-compliant Category 3 shielded or unshielded cabling. 1/2.5/5Gbps: Standard TIA/EIA 568-A-compliant Category 5 or TIA/

EIA 568-B-compliant Enhanced Category 5 (Cat 5e) shielded or unshielded cabling. The LAN port has a maximum operating distance of 100 meters (328 feet). Refer to Table 8 on page 72 for the port pinouts of the LAN port when it is operating at 10/100Mbps in the MDI configuration and Table 9 on page 73 for the MDI-X configuration. Refer to Table 10 on page 73 for the port pinouts when the port is operating at 1/2.5/5Gbps. 27 Review Draft - August 12, 2020 Chapter 1: Product Description How to Power the Wireless Access Point There are three ways to power the wireless access point:

External AC/DC Power Adapter, next PoE+ Power Source on page 28 Both AC/DC Power Adapter and PoE Power Source on page 29 Note The input power specifications of the wireless access point are listed in Table 4 on page 70 in Appendix A, Technical Specifications on page 69. External AC/DC Power Adapter One way to power the wireless access point is with an external AC/DC power adapter, such as the PWRADP-01 (DA-48Z12) Power Adapter from Allied Telesis. Refer to Figure 4. The power adapter is connected to the DC IN connector on the rear panel of the wireless access point. Figure 4. Powering the Access Point with an AC/DC Power Adapter PoE+ Power Source The wireless access point is a PoE+ powered device, Class 4. It can also be powered by a PoE power source on its Ethernet LAN port. An example of a PoE power source is the x320-10GH PoE++ Ethernet Switch from Allied Telesis. Refer to Figure 5. Figure 5. Powering the Access Point with a PoE Power Source 28 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Finally, the device can be powered by both an external AC/DC power adapter and a PoE+ power source. Refer to Figure 6. Both AC/DC Power Adapter and PoE Power Source Figure 6. Powering the Access Point with Both an External AC/DC Adapter and a PoE+ Power Source Here are the operating rules of the wireless access point when connected to both an AC/DC power adapter and a PoE+ power source:

The two power sources are not load sharing. The power adapter is the primary power source and PoE is held in reserve. The LAN port operates as a standard Ethernet LAN port, with PoE blocked. If the power adapter stops providing power, the wireless access point automatically changes to PoE on the LAN port as its power source. If the power adapter resumes providing power, the wireless access point automatically switches back to the power adapter as its primary power source. PoE on the LAN port is blocked and returned to reserve status. 29 Review Draft - August 12, 2020 Chapter 1: Product Description DC Connector for an External AC/DC Power Adapter The DC IN connector is for an external AC/DC power adapter, such as the PWRADP-01 Power Adapter from Allied Telesis, shown in Figure 7. Figure 7. PWRADP-01 Power Adapter You can power the wireless access point with either an external power adapter on the DC IN connector or a PoE+ power source on the Ethernet LAN port. You can also power it with both power sources. Refer to How to Power the Wireless Access Point on page 28 and Power Specifications on page 70. Note Use only power sources that are UL Listed (QQGQ or EPBU), TUV Licensed, or other Safety Agencies approved, and that are suitable for country of use. 30 Review Draft - August 12, 2020 POWER On/Off Button TQ6602 Wireless Access Point Installation Guide The POWER On/Off button on the rear panel powers on or off the DC IN connector for an external AC/DC power adapter. Here are the button settings:

In - The DC IN connector is On, allowing power from the AC/DC Out - The DC IN connector is Off, blocking power from the AC/DC adapter. adapter. Here are the guidelines:

If the wireless access point is powered by both an AC/DC power adapter and a PoE power source, turning off the DC IN connector shuts off power from the adapter. The access point automatically switches over to PoE for power. If the wireless access point is powered only by an AC/DC power adapter, turning off the DC IN connector shuts down the device. 31 Review Draft - August 12, 2020 Chapter 1: Product Description LEDs 32 The LEDs on the top panel display status information. They are defined in Table 1. Table 1. LED Status Information LED State Description Solid Green Solid Red Blinking Red Power The access point is powered on and operating normally. The device is booting up or has encountered a fault condition. The access point is upgrading its firmware. The access point is not receiving power. Solid Green The port has established a link to a network device. Blinking Green The port is transmitting or receiving data. LAN Solid Amber The LAN port is connected to a PoE+

source device. Off Off Solid Green The 2.4GHz Radio1 is enabled. The port has not established a link to a network device. The access point is querying the wireless network on the 2.4GHz radio for a Smart Connect network of Vista Manager EX and the AWC plug-in. The access point is in a Smart Connect network and will automatically configure its settings from the AWC plug-in. Slow Blinking Green 2.4GHz Wi-Fi Fast Blinking Green Off The 2.4GHz Radio1 is disabled. Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Table 1. LED Status Information LED State Description Solid Green The 5GHz Radio2 is enabled. Slow Blinking Green 5GHz Wi-Fi Fast Blinking Green The access point is querying the wireless network on the 5GHz radio for a Smart Connect network of Vista Manager EX and the AWC plug-in. The access point is a member of a Smart Connect network and will automatically configure its settings from the AWC plug-in. Off The 5GHz Radio2 is disabled. 33 Review Draft - August 12, 2020 Chapter 1: Product Description Reset Button The wireless access point has a Reset button on the rear panel. The button has two functions. The selected function depends on how long the button is pressed:

One to four seconds: Reboots the wireless access point. More than five seconds: Restores all the settings on the wireless access point to their default values, including manager name and password. You can enable or disable the reset button with the management software. The default setting for the button is enabled. If the access point is installed in a public area, you should disable it to prevent unauthorized individuals from resetting the device and interrupting network operations.

<<Reviewers, I did not understand the table provided in the TQ6602_Reset_SW_spec.pdf review. I would appreciate it if you could provide a clearer explanation.>>

34 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Management Tools Web Browser The wireless access point supports the following management tools. The wireless access point has a web browser management interface for configuring the device from your management workstation. The web browser interface allows you to manage one unit at a time and supports both non-secure HTTP and secure HTTPS management sessions. The default is HTTP. The product has been tested with Microsoft Internet Explorer version 11 or later, Microsoft Edge, and Chrome. Vista Manager EX and AWC Plug-in The wireless access point supports Vista Manager and the Autonomous Wave Control (AWC) plug-in. Configuring and monitoring large numbers of devices is simplified with AWC because you can add multiple devices to management groups and manage them as one unit. The application can also monitor the operations of the wireless access points and automatically adjust operating properties to optimize the performance of your wireless network. Note The Channel Blanket feature in the TQ6602 Access Point requires Vista Manager EX and the AWC plug-in. Note The TQ6602 Wireless Access Point requires Vista Manager EX and AWC plug-in version 2.5.1 or later. SNMP You can use SNMPv1 or v2c to view the parameter settings of the devices. The MIB is available from the Allied Telesis web site. For instructions on how to configure the unit for SNMP, refer to the TQ6602 Wireless Access Point Management Software User Guide. 35 Review Draft - August 12, 2020 Chapter 1: Product Description 36 Review Draft - August 12, 2020 Chapter 2 Beginning the Installation This chapter contains the following sections:

Reviewing Safety Precautions on page 38 Choosing a Site for the Wireless Access Point on page 41 Unpacking the Shipping Box on page 42 Note The non-US models of this product have a country code setting that has to be set during the initial management session of the units. The setting ensures that the units operate in compliance with the laws and regulations of your country or region. For the US model, the country code is preset and cannot be changed. Per FCC regulations, the country code setting for all WiFi products marketed in the US have to be fixed to US operational channels only. 37 Review Draft - August 12, 2020 Chapter 2: Beginning the Installation Reviewing Safety Precautions Please review the following safety precautions before installing the access point. Important: Safety statements that have the symbol are translated into multiple languages in the Translated Safety Statements document, which is available at www.alliedtelesis.com/library. Remarque: Les consignes de scurit portant le symbole sont traduites dans plusieurs langues dans le document Translated Safety Statements, disponible l'adresse www.alliedtelesis.com/library. Warning To prevent electric shock, do not remove the cover. No user-serviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician. To avoid the possibility of electric shock, disconnect electric power to the product before connecting or disconnecting the LAN cables. E1 Warning Do not work on equipment or cables during periods of lightning activity. E2 Warning All Countries: Install product in accordance with local and National Electrical Codes. E8 Warning Only trained and qualified personnel are allowed to install or to replace this equipment. E14 Warning To reduce the risk of electric shock, the PoE ports on this product must not connect to cabling that is routed outside the building where this device is located. E40 38 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Warning This equipment shall be installed in a Restricted Access location. E45 Warning FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Note The access point must be powered by:

1. A UL listed external AC/DC power supply suitable for use at Tma 50oC, a maximum operating altitude of 3000 m or higher, and whose output meets separated extra-low voltage (SELV), limited power sources (LPSs) and is rated 12 VDC, 4.0 A, Refer to Table 5, External AC/DC Power Adapter Specifications on page 70. OR 2. By Power over Ethernet through a UL listed ITE. Caution Air vents must not be blocked and must have free access to the room ambient air for cooling. E6 Warning An operational unit can be hot. Exercise caution when handling with unprotected hands. Warning Operating Temperature. This product is designed for a maximum ambient temperature of 50C (122 F) E7. Warning To reduce the risk of electric shock, the PoE port on this product must not connect to cabling that is routed outside the building where this device is located. E40 39 Review Draft - August 12, 2020 Chapter 2: Beginning the Installation Warning This equipment is intended for indoor use only. E95 Note If you are not using PoE to power to unit, use only an approved AC/

DC adapter. Refer to External AC/DC Power Adapter Specifications on page 70. Caution The unit does not contain serviceable components. Please return damaged units for servicing. E42 Note You should verify that your PoE network adheres to the standards of a separated extra-low voltage (SELV) circuit before using the PoE feature on the wireless access point. 40 Review Draft - August 12, 2020 Choosing a Site for the Wireless Access Point TQ6602 Wireless Access Point Installation Guide Observe these requirements when planning the installation of the wireless access point:

The ceiling or wall mounting surface should be of proper material to accommodate the screws and strong enough to support the weight of the wireless access point and cables. (Refer to Table 2 on page 69 for product weight.) Verify that the Ethernet cable is long enough to connect to its destination port. If the wireless access point will be powered by an AC/DC adapter, verify that an AC power outlet is within six feet of the planned installation site. The site should allow for easy access to the Ethernet port on the device, so that you can easily connect and disconnect the cable. The site should allow for adequate air flow around the unit and through the cooling vents on the bottom panel. The site should not expose the device to moisture or water. The site should be a dust-free environment. The site should not expose the twisted pair cabling to sources of electrical noise, such as radio transmitters, broadband amplifiers, power lines, electric motors, and fluorescent fixtures. Do not place objects on top of the device. If installing the device in a wiring or utility box, verify that there is adequate airflow to prevent overheating. 41 Review Draft - August 12, 2020 Chapter 2: Beginning the Installation Unpacking the Shipping Box The contents of the shipping box are shown in Figure 8. Verify and inspect the contents. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. Note Store the packaging material in a safe location. Please use the original shipping material if you need to return the device to Allied Telesis. TQ6602 Wireless Access Point Wall Mounting Bracket Two M5 x 8mm, Pan-head Screws Figure 8. Shipping Box Contents 42 Review Draft - August 12, 2020 Chapter 3 Installing the Wireless Access Point This chapter contains the installation procedures for the TQ6602 Wireless Access Point. The procedures are detailed in the following sections:

Installing the Wireless Access Point on a Table on page 44 Overview to Installing the Wireless Access Point on a Wall or Ceiling on page 48 Installing the Mounting Bracket on a Wall or Ceiling on page 51 Installing the Mounting Bracket Screws on page 55 Connecting an Ethernet Cable to the Ethernet LAN Port on page 56 Connecting the AC/DC Power Adapter on page 57 Attaching the Wireless Access Point to the Wall Mounting Bracket on page 59 Installing an Anti-theft Device on page 61 43 Review Draft - August 12, 2020 Chapter 3: Installing the Wireless Access Point Installing the Wireless Access Point on a Table Figure 9 Shows the wireless access point on a table. Figure 9. TQ6602 Wireless Access Point on a Table You need the following items to install the access point on a table:

TQ6602 Wireless Access Point. Wall mounting bracket (provided).

(provided). One Ethernet cable. Two screws to attach the wall mounting bracket to the access point External AC/DC power supply (Optional if using PoE. Required if not using PoE or for redundant power). Kensington lock (optional). Note Allied Telesis recommends installing the wall mounting bracket on the bottom panel of the wireless access point when installing the device on a table. The bracket will facilitate airflow through the cooling fins under the device. Note Please see Reviewing Safety Precautions on page 38 and Choosing a Site for the Wireless Access Point on page 41 before installing the product. Perform the following steps to install the wireless access point on a table:

1. Place the wireless access point upside down on a table. 2. Install the two screws (provided) fully into the bottom panel of the access point. Refer to Figure 10 on page 45. 44 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Figure 10. Installing the Bracket Screws The screw collar provides the proper spacing for the mounting bracket beneath the screw head. Refer to Figure 11. Figure 11. Panel Screws 3. Slide the mounting bracket beneath the screws. Refer to Figure 12 on page 46. Collar 45 Review Draft - August 12, 2020 Chapter 3: Installing the Wireless Access Point Figure 12. Installing the Mounting Bracket 4. Tighten the bracket retaining screw. Refer to Figure 13. Figure 13. Tightening Bracket Retaining Screw 5. Turn the wireless access point upright on the table. 6. Place the wireless access point at the selected location. 46 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide 7. Go to one the following procedures Connecting an Ethernet Cable to the Ethernet LAN Port on page 56. Connecting the AC/DC Power Adapter on page 57. Installing an Anti-theft Device on page 61. 47 Review Draft - August 12, 2020 Chapter 3: Installing the Wireless Access Point Overview to Installing the Wireless Access Point on a Wall or Ceiling You can install the wireless access point on a wall with the front panel pointing to the left, down. or right. Refer to Figure 14. Figure 14. Orientations of the TQ6602 Wireless Access Point on a Wall Do not install the device with the front panel facing up. Refer to Figure 15. Figure 15. Invalid Position of the TQ6602 Wireless Access Point on a Wall 48 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Figure 16 shows the device installed on a ceiling. Figure 16. TQ6602 Wireless Access Point on the Ceiling Here are the procedures for installing the wireless access point on a wall or ceiling:

Installing the Mounting Bracket on a Wall or Ceiling on page 51 Installing the Mounting Bracket Screws on page 55 Connecting an Ethernet Cable to the Ethernet LAN Port on page 56 Connecting the AC/DC Power Adapter on page 57 Attaching the Wireless Access Point to the Wall Mounting Bracket on page 59 Installing an Anti-theft Device on page 61 Note Please see Reviewing Safety Precautions on page 38 and Choosing a Site for the Wireless Access Point on page 41 before installing the product. Depending on the installation location, it may be easier to connect the network cables and power adapter to the wireless access point before installing it on the wall or ceiling. You need the following items to install the wireless access point on a ceiling or wall:

Two screws to attach the access point to the mounting bracket TQ6602 Wireless Access Point

(provided) Wall mounting bracket (provided) Four (4) M4, 25.0 mm flat-head wood screws and anchors for fastening the mounting bracket (not provided) Phillips head screwdriver (not provided) Pencil (not provided) 49 Review Draft - August 12, 2020 Chapter 3: Installing the Wireless Access Point External AC/DC power supply (Optional if using PoE. Required if not using PoE or for redundant power.) Kensington lock (optional and not provided) Note The four Phillips head M4 screws/anchors, the Phillips head screwdriver, pencil, external AC/DC power supply and Kensington lock are not included with the product. 50 Review Draft - August 12, 2020 Installing the Mounting Bracket on a Wall or Ceiling TQ6602 Wireless Access Point Installation Guide To install the mounting bracket on a wall of ceiling, perform the following procedure:

1. Choose the location and orientation for the access point on the wall or ceiling. Refer to Figure 14 on page 48. 2. Position the mounting bracket at the selected location and orientation for the access point. Consider the following guidelines. The thumbscrew on the mounting bracket is where the front panel of the access point will be. The ports and connectors are on the back panel, away from the thumbscrew. 3. With a pencil, mark the wall or ceiling with the two key-hole slots of the bracket. Refer to Figure 17. Figure 17. Marking the Holes for the Key-Hole Slots 4. Pre-drill the two marked locations for the keyhole slots on the ceiling or wall. 5. Install two M4 screws and anchors (if required). Leave the screws loose enough so that the bracket can slide under the screw heads. Refer to Figure 18 on page 52. 51 Review Draft - August 12, 2020 Chapter 3: Installing the Wireless Access Point Note For a wooden wall or ceiling, use M4, 25.0 mm flat-head wood screws and anchors, if required. The screws and anchors are not provided with the wireless access point. Figure 18. Installing Two Screws 6. Insert the openings of the bracket key-hole slots under the two screw heads and slide the bracket into the narrow end of the key-hole slot openings. Refer to Figure 19 on page 53. 52 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Figure 19. Installing the Wall Mounting Bracket On the Screws 7. Tighten the screws snugly onto the bracket. 8. To secure the mounting bracket, pre-drill holes through the two bracket mounting holes opposite the key-hole slots. Refer to Figure 20. Figure 20. Pre-Drill Holes on Wall Mounting Bracket 9. Install and tighten two M4 screws (not provided) in the holes prepared in Step 8. Refer to Figure 21. The bracket installation is now complete. 53 Review Draft - August 12, 2020 Figure 21. Securing the Wall Mounting Bracket 10. Go to Installing the Mounting Bracket Screws on page 55. Chapter 3: Installing the Wireless Access Point 54 Review Draft - August 12, 2020 Installing the Mounting Bracket Screws TQ6602 Wireless Access Point Installation Guide To install the mounting bracket screws in the wireless access point, perform the following procedure:

1. Place the wireless access point upside down on a table. 2. Install the two screws (provided) fully into the bottom panel of the access point. Refer to Figure 22. Figure 22. Installing the Bracket Screws into the Wireless Access Point The screw collar provides the proper spacing for the mounting bracket beneath the screw head. Refer to Figure 11 on page 45. 3. Do one of the following:

Depending on the installation location, it may be easier to connect the Ethernet cable and optional AC/DC power adapter to the wireless access point before installing it on the wall of ceiling. If that is the case in your installation, continue with the installation by going to Connecting an Ethernet Cable to the Ethernet LAN Port on page 56. To install the wireless access point on the wall of ceiling before attaching the cables, go to Attaching the Wireless Access Point to the Wall Mounting Bracket on page 59. 55 Review Draft - August 12, 2020 Chapter 3: Installing the Wireless Access Point Connecting an Ethernet Cable to the Ethernet LAN Port This section contains the procedure for connecting an Ethernet cable to the LAN port. For information on cable specifications, refer to Cable Requirements on page 27. Please review the following guidelines before connecting the Ethernet cable:

If you are installing the wireless access point on a ceiling or wall, you might find it easier to connect the cable before placing the unit on the wall mounting bracket. To power the wireless access point with PoE, connect the LAN port to a PoE source device. For power specifications, refer to PoE+ Power Requirements on page 70. To connect the network cable, perform the following procedure:

1. Connect an Ethernet cable into the RJ-45 LAN port. Refer to Figure 23. Note If the other end of the Ethernet cable is already connected to a PoE source device, the wireless access point begins to power on and initialize its management software. Figure 23. Connecting an Ethernet Cable to the LAN Port 2. Connect the other end of the Ethernet cable to a network Ethernet device, such as an Ethernet switch or router. 3. Do one of the following:

If the access point will be powered by PoE only, without an AC/DC power adapter, go to Attaching the Wireless Access Point to the Wall Mounting Bracket on page 59. To power the access point with an external AC/DC power adapter, go to Connecting the AC/DC Power Adapter on page 57. 56 Review Draft - August 12, 2020 Connecting the AC/DC Power Adapter TQ6602 Wireless Access Point Installation Guide You can power the wireless access point with PoE on the LAN port or an AC/DC power adapter, or both. Refer to How to Power the Wireless Access Point on page 28. To connect a power adapter to the wireless access point, perform the following procedure:

1. If you purchased the PWRADP-01 Power Adapter, connect the AC power cord to the power adapter. Refer to Figure 24. Figure 24. Connecting the AC Power Cord to the PWRADP-01 Power Adapter 2. Plug the DC cable from the power adapter into the DC IN connector on the wireless access point. Refer to Figure 25. Figure 25. Connecting an AC/DC Power Adapter to the DC IN Connector 3. Connect the power adapter into an appropriate AC power source. Refer to Figure 26. 57 Review Draft - August 12, 2020 Chapter 3: Installing the Wireless Access Point Figure 26. Connecting the Power Cord on the PWRADP-01 Power Adapter to an AC Source 4. Push the DC Power On/Off Button on the wireless access point to the IN position to turn on the DC connector. Refer to Figure 27. Note The DC Power Button controls the DC connector. It does not control PoE on the LAN port. Figure 27. DC Power On/Off Button The wireless access point begins to initialize its management software. The process takes about one minute to complete. 5. Go to Attaching the Wireless Access Point to the Wall Mounting Bracket on page 59. 58 Review Draft - August 12, 2020 Attaching the Wireless Access Point to the Wall Mounting Bracket TQ6602 Wireless Access Point Installation Guide To attach the wireless access point to the wall mounting bracket on the wall or ceiling, perform the following procedure:

1. Align the bottom of the access point over the bracket so that the two screws on the bottom of the device fit into the bracket keyholes. Refer to Figure 28. (The two screws are installed in Installing the Mounting Bracket Screws on page 55.) Figure 28. Installing the Wireless Access Point on the Wall Mounting Bracket 2. Slide the wireless access point until its screws are seated in the bracket keyhole slots and the bracket thumbscrew is aligned with the screw hole on the front panel. Refer to Figure 29 on page 60. 59 Review Draft - August 12, 2020 Chapter 3: Installing the Wireless Access Point Figure 29. Seating the Wireless Access Point on the Wall Mounting Bracket 3. Tighten the thumbscrew to secure the wireless access point to the wall mounting bracket. Refer to Figure 30. Figure 30. Tightening the Wall Mounting Bracket Thumbscrew 4. Go to Installing an Anti-theft Device on page 61 or Chapter 4, Managing the Wireless Access Point on page 63. 60 Review Draft - August 12, 2020 Installing an Anti-theft Device TQ6602 Wireless Access Point Installation Guide Installation of an anti-theft cable/lock is optional. The access point has a lock port that is compatible with a Kensington lock. The lock port can be used to physically secure the device to a table, wall, or a ceiling. Note Anti-theft devices are not available from Allied Telesis. Follow the instructions provided with the vendors anti-theft device for the installation. Refer to Figure 31 for the Kensington lock port location. Kensington Lock Port Figure 31. Kensington Lock Port If you are installing the wireless access point on a wall or ceiling and have not installed it on the mounting bracket yet, go to Attaching the Wireless Access Point to the Wall Mounting Bracket on page 59. Otherwise, go to Chapter 4, Managing the Wireless Access Point on page 63. 61 Review Draft - August 12, 2020 Chapter 3: Installing the Wireless Access Point 62 Review Draft - August 12, 2020 Chapter 4 Managing the Wireless Access Point This chapter contains the following sections:

Starting the First Management Session Without a DHCP Server on page 64 Starting a Management Session on page 67 63 Review Draft - August 12, 2020 Chapter 4: Managing the Wireless Access Point Starting the First Management Session Without a DHCP Server After you install and power on the wireless access point, it queries the subnet on the LAN port for a DHCP server. If a DHCP server responds to its query, the unit uses the IP address the server assigns to it. If there is no DHCP server, the access point uses the default IP address 192.168.1.230. If your network has a DHCP server, use the IP address the server assigns it to it to start the management session. For directions, refer to Starting a Management Session on page 67 If your network does not have a DHCP server, you can start the first management session by establishing a direct connection between your computer and the unit by connecting an Ethernet cable to the Ethernet port on the computer and the LAN1 port on the access point. This procedure requires changing the IP address on your computer to make it a member of the same subnet as the default IP address on the access point. The first management session can also be performed while the device is connected to your network. However, If your network does not have a DHCP server, you still have to change the IP address of your computer to match the subnet of the default address of the access point. Furthermore, if your network is divided into virtual LANs (VLANs), you have to be sure to connect the access point and your computer to ports on an Ethernet switch that are members of the same VLAN. The instructions for starting the first management session are found in the following sections:

Starting the First Management Session with a Direct Connection on page 65 Starting the First Management Session Over a Network on page 65 Note The first management session of the access point has to be conducted through the LAN port because the default setting for the radios is off. 64 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Starting the First Management Session with a Direct Connection To start the management session with a direct Ethernet connection between your computer and the LAN port on the access point, perform the following procedure:

Note If the access point is powered only with PoE, you cannot perform this procedure because it requires a direct connection between your computer and the LAN port on the access point. Instead, perform Starting the First Management Session Over a Network on page 65. 1. Connect one end of a network cable to the LAN port on the access point and the other end to the Ethernet network port on your computer. 2. Change the IP address on your computer to 192.168.1.n, where n is a number from 1 to 254, but not 230. Refer to the documentation that accompanies your computer for instructions on how to set the IP address. 3. Set the subnet mask on your computer to 255.255.255.0. 4. Power on the access point. 5. Start the web browser on your computer. 6. Enter the IP address 192.168.1.230 in the URL field of the browser and press the Enter key. You should now see the login window, shown in Figure 32 on page 67. 7. Enter manager for the user name and friend for the password. The user name and password are case-sensitive. 8. Click the Login button. This procedure explains how to start the first management session on the access point when the LAN port is connected to an Ethernet switch on a network that does not have a DHCP server. To start the management session, perform the following procedure:

1. If your network has VLANs, check to be sure that your computer and the access point are connected to ports on the Ethernet switch that are members of the same VLAN. This might require accessing the management software on the switch and listing the VLANs and their port assignments. For example, if the access point is connected to a port that is a member of the Sales VLAN, your computer must be connected to a port that is also a member of that VLAN. If your network is small and does not have VLANs or routers, you can connect your computer to any port on the Ethernet switch. 65 Starting the First Management Session Over a Network Review Draft - August 12, 2020 Chapter 4: Managing the Wireless Access Point 2. Change the IP address on your computer to 192.168.1.n, where n is a number from 1 to 254, but not 230. Refer to the documentation that accompanies your computer for instructions on how to set the IP address. 3. Set the subnet mask on your computer to 255.255.255.0. 4. Power on the access point. 5. Start the web browser on your computer. 6. Enter the IP address 192.168.1.230 in the URL field of the browser and press the Return key. You should now see the logon window, shown in Figure 32 on page 67. 7. Enter manager for the user name and friend for the password. The user name and password are case-sensitive. 8. Click the Login button. 66 Review Draft - August 12, 2020 Starting a Management Session TQ6602 Wireless Access Point Installation Guide This section explains how to start a management session on the access point from your management workstation, using a web browser. The procedure assumes that the access point has already been assigned an IP address, either manually or from a DHCP server. Note If the access point is using its default address 192.168.1.230, refer to Starting the First Management Session Without a DHCP Server on page 64 for instructions. To start a management session on the access point, perform the following procedure:

1. Open the web browser on your management workstation. 2. Enter the IP address of the access point in the URL field of the web browser. Note Precede the IP address with HTTPS:// if the access point is already configured for HTTPS management. The default is HTTP management. You should now see the log on window in Figure 32. Figure 32. Log On Window 67 Review Draft - August 12, 2020 Chapter 4: Managing the Wireless Access Point Note If you use HTTPS management, your web browser might display a warning message stating that the site certificate is invalid. If this occurs, select an appropriate option to continue to the web site. To avoid the message in future management sessions, make the web site a trusted site in your web browser. 3. Enter the user name and password for the unit. The default values are manager for the user name and friend for the password. The user name and password are case-sensitive. 4. Click the Login button. 68 Review Draft - August 12, 2020 Appendix A Technical Specifications Physical Specifications Environmental Specifications This appendix contains the specifications for the TQ6602 Wireless Access Point in the following sections:

Physical Specifications Environmental Specifications Power Specifications on page 70 Cable Specifications on page 71 LAN Ports Specifications and Pinouts on page 72 Table 2. Physical Specifications Parameter Specification Dimensions (W x D x H) 205 mm X 225 mm X 51 mm

(8.07 in. x 8.86 in. x 2.01 in.) Weight without mounting bracket tbd g (tbd lbs) Weight with mounting bracket tbd g (tbd lbs) Table 3. Environmental Specifications Parameter Specification Operating Temperature when powered by AC/DC adapter Operating Temperature when powered by PoE power source 0 C to 50 C (32 F to 122 F) 0 C to 50 C (32 F to 122 F) Storage Temperature

- 25 C to 70 C (- 13 F to 158 F) Operating Humidity 5% to 90% non-condensing Storage Humidity 5% to 95% non-condensing Maximum Operating Altitude 3000 m (9843 ft) 69 Review Draft - August 12, 2020 Appendix A: Technical Specifications Power Specifications Input Power Specifications Table 4 lists the power requirements of the TQ6602 Wireless Access Point. Table 4. Input Power Specifications Parameter Specification Rated Input Voltage

+12 VDC Maximum Input Current Average Input Current 4A tbd A External AC/DC Power Adapter Specifications Table 5 lists the power requirements for an external AC/DC power adapter. Table 5. External AC/DC Power Adapter Specifications Parameter Input Voltage Range Input Frequency Rated Output Voltage Rated Output Current Specification 100~240 VAC 50 - 60 Hz

+12 VDC 0-4.0A Note Allied Telesis recommends the PWRADP-01 AC/DC power adapter. It is UL Listed and fully compatible with the above specifications, while meeting the standards of a separated extra-low voltage

(SELV) product. The adapter is sold separately. PoE+ Power Requirements Table 6 lists the PoE+ specifications for the Ethernet port. Table 6. PoE Power Requirements on the Ethernet Port Parameter Specification Power PoE+ Device Classification tbd watts Class 4 70 Review Draft - August 12, 2020 Cable Specifications TQ6602 Wireless Access Point Installation Guide The minimum cable requirements for the Ethernet port are listed here. 10/100Mbps: Standard TIA/EIA 568-B-compliant Category 3 shielded or unshielded cabling. 1/2.5/5Gbps: Standard TIA/EIA 568-A-compliant Category 5 or TIA/

EIA 568-B-compliant Enhanced Category 5 (Cat 5e) shielded or unshielded cabling. The maximum operating distance is 100 meters (328 feet). 71 Review Draft - August 12, 2020 Appendix A: Technical Specifications LAN Ports Specifications and Pinouts Port Specifications The access point port specifications are shown in Table 7. Table 7. LAN Port Specifications Connector Specification Standards IEEE 802.3 (10Base-T) IEEE 802.3u (100Base-TX) IEEE 802.3ab (1000Base-T) IEEE 802.3bz (2.5Base-T IEEE 802.3bz (5Base-T) PoE standard IEEE 802.3at (class tbd) Port Pinouts The pin signal definitions for the Ethernet port are given here. Figure 33 illustrates the pin layout of the port. Figure 33. Pin Layout for RJ45 Connector on the Ethernet Port Table 8 lists the pin signals for ports operating at 10/100Mbps in the MDI configuration. Table 8. MDI Pin Signals at 10/100Mbps Pin Signal 1 2 3 6 TX+

TX-

RX+

RX-

72 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Table 9 lists the pin signals for ports operating at 10/100Mbps in the MDIX configuration. Table 9. MDIX Pin Signals at 10/100Mbps Pin Signal 1 2 3 6 RX+

RX-

TX+

TX-

Table 10 lists the pin signals for LAN ports operating at 1/2.5/5Gbps. Table 10. Connector Pinouts at 1/2.5/5Gbps Pin Pair Signal 1 2 3 4 5 6 7 8 1 1 2 3 3 2 4 4 TX and RX TX and RX-

TX and RX+

TX and RX+

TX and RX-

TX and RX-

TX and RX+

TX and RX-

73 Review Draft - August 12, 2020 Appendix A: Technical Specifications 74 Review Draft - August 12, 2020 Appendix B Regulatory Statements This appendix contains the following regulatory statements:

Federal Communication Commission Interference Statement on page 76 Industry Canada Statement on page 78 Europe - EU Declaration of Conformity on page 80 75 Review Draft - August 12, 2020 Appendix B: Regulatory Statements Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Caution Avertissement de la FCC: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. E80 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range, it is restricted to indoor environment. The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. 76 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. 77 Review Draft - August 12, 2020 Appendix B: Regulatory Statements Industry Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-

exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lemetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

(1) Lappareil ne doit pas produire de brouillage.

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la Class B est conforme la norme NMB-003 du Canada. Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-

5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

(iii) the maximum antenna gain permitted for devices in the band 5725-

5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate;

(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated; and

(v) Users should also be advised that high-power radars are allocated as primary users (i.e., priority users) of the bands 5250-5350 MHz and 5650-

5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. 78 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide Avertissement:

Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 5 350 MHz et de 5470 5725 MHz doit tre conforme la limite de la p.i.r.e;

(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;

(iv) les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, et nonce la section 6.2.2 3), doivent tre clairement indiqus;

(v) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--

d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. 79 Review Draft - August 12, 2020 Appendix B: Regulatory Statements Europe - EU Declaration of Conformity Operating Frequencies and Maximum Transmission Power Levels Hereby, Allied Telesis declares that the radio equipment type

[TQ6602] is in compliance with Directive 2014/53/EU. The operating frequencies and maximum transmission power levels for wireless devices operated in the EU are listed below:

- 2412-2472 MHz:

- 5150-5250 MHz:

- 5250-5350 MHz:

- 5470-5725 MHz:

19.23 dBm (Beamforming), 18.79dBm (Non-Beamforming) 22.11 dBm (Beamforming), 22.13dBm (Non-Beamforming) 22.06 dBm (Beamforming), 21.87dBm (Non-Beamforming) 28.97 dBm (Beamforming), 28.70dBm (Non-Beamforming) Note Operations in the 5.15 - 5.35 GHz band are restricted to indoor usage only. Radiation Exposure Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Importer Allied Telesis International BV Incheonweg 7, 1437 EK Rozenburg Note Contact Allied Telesis for the EU conformity statement. To contact Allied Telesis, visit our web site at www.alliedtelesis.com/contact. 80 Review Draft - August 12, 2020 Appendix C Radiation Patterns This appendix contains the following sections:

2.4GHz Antenna 1 on page 82 2.4GHz Antenna 2 on page 83 2.4GHz Antenna 3 on page 84 2.4GHz Antenna 4 on page 85 5GHz Antenna 1 on page 86 5GHz Antenna 2 on page 87 5GHz Antenna 3 on page 88 5GHz Antenna 4 on page 89 Z X Y Figure 34. Axes on the TQ6602 Access Point 81 Review Draft - August 12, 2020 Appendix C: Radiation Patterns 2.4GHz Antenna 1 TBD 82 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide 2.4GHz Antenna 2 TBD 83 Review Draft - August 12, 2020 Appendix C: Radiation Patterns 2.4GHz Antenna 3 TBD 84 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide 2.4GHz Antenna 4 TBD 85 Review Draft - August 12, 2020 Appendix C: Radiation Patterns 5GHz Antenna 1 TBD 86 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide 5GHz Antenna 2 TBD 87 Review Draft - August 12, 2020 Appendix C: Radiation Patterns 5GHz Antenna 3 TBD 88 Review Draft - August 12, 2020 TQ6602 Wireless Access Point Installation Guide 5GHz Antenna 4 TBD 89 Review Draft - August 12, 2020 Appendix C: Radiation Patterns 90 Review Draft - August 12, 2020

TQ6602 Enterprise-class 802.11ax Indoor Wireless Access Point with 2.4GHz and 5GHz Radios Installation Guide 613-002891 Rev. A Review Draft - July 13, 2020 Copyright 2020 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages. Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Electrical Safety and Emissions Standards This product meets the following standards:

Federal Communications Commission Interference Statement European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment on page 4 Safety and Electromagnetic Emissions on page 4 Translated Safety Statements on page 8 Federal Communications Commission Interference Statement Declaration of Conformity Manufacturer Name: Allied Telesis Declares that the product: 802.11a/b/g/n/ac/ax wave2 dual radio 2.4G (4x4) and 5G (4x4) wireless access point Model Number: TQ6602 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3 Review Draft - July 13, 2020 Caution FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Avertissement Avertissement de la FCC: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. E80 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Allied Telesis ensures RoHS conformance by requiring supplier Declarations of Conformity, monitoring incoming materials, and maintaining manufacturing process controls. Note For additional regulatory statements, refer to Appendix B, Regulatory Statements on page 77. Safety and Electromagnetic Emissions Standard Compliance RoHs compliant European Union RoHS (Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.) 4 Review Draft - July 13, 2020 Wire Communication IEEE 802.1 IEEE 802.3 IEEE 802.3u IEEE 802.3z IEEE 802.3bz+-

IEEE 802.3x IEEE 802.3at ITU-T G.993.1 Wireless LAN Communication IEEE 802.11 DSSS IEEE 802.11a OFDM IEEE 802.11b DSSS/FHSS IEEE 802.11g OFDM IEEE 802.11n OFDM IEEE 802.11ac OFDM IEEE 802.11ax OFDMA ARIB STD-T66 ARIB STD-T71 Safety CB/UL TUV AEL EN62368-1 (Co-license) Class I, US FDA/CDRH EN(IEC) 60825-1:1994+a11, EN(IEC) 60825-2:1994 EN(IEC) 60950: 1992+A1+A2+A3 UL2043 IEC 62368-1: 2014 and EN62368-1: 2014 UL 62368-1: 2nd Edition, 2014-12-01 CSA C22.2 No. 62368-1-14, 2nd Edition, 2014-12-01 TQ6602 Wireless Access Point Installation Guide 5 Review Draft - July 13, 2020 Electro Magnetic Susceptibility (EMS) - EN55024 and EN55035 IEC 61000-4-2:2008 IEC 61000-4-3: 2006+A1:2007+A2:2010 Electro Magnetic Interference (EMI) FCC part15 Subpart B/ Class B EN55032 Class B VCCI-CISPR 32:2016 VCCI Class B VCCI 32.1 AS/NZS CISPR 32 IEC 61000-4-4:2012 IEC 61000-4-5:2017 IEC 61000-4-6:2013

(IEC 61000-4-8:2009) IEC 61000-4-11 2017 IEC 61000-3-2:2014 IEC 61000-3-3:2013 47 CFR Part15, subpart C 47 CFR Part15, subpart E FCC DFS CE RED Directive 2014/53/EU EN55032:2015+AC:2016

(CISPR32:2015/COR1:2016) EN 55024:2010+A1:2015 EN 301489-1 V2.1.1 EN 301489-17 V3.1.1 EN 300328 V2.1.1 EN 301893 V2.1.1 EN 62311: 2008 / EN 50385: 2017 IEC 61000-4-5:2017 European Council Directive 2014/30/EU DFS 6 Review Draft - July 13, 2020 EN 55035 EN 60601-1-2 RCM IC AS/NZS CISPR 32: 2015 AS/NZS 4268: 2017 ICES-003 issue 6 RSS-102 RSS-247 issue 2 Japan JATE ARIB STD-T66 ARIB STD-T71 Hong Kong OFCA India WPC Malaysia SIRIM Singapore IMDA TS SRD Taiwan BSMI & NCC CNS 13438 CNS 14336-1

(LP002) Thailand NBTC Vietnam MIC China SRRC TQ6602 Wireless Access Point Installation Guide Complies with IMDA Standards DB102434 Figure 1. Singapore IMDA Logo 7 Review Draft - July 13, 2020 Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements on the Allied Telesis website at www.alliedtelesis.com/library. Remarque: Les consignes de scurit portant le symbole sont traduites dans plusieurs langues dans le document Translated Safety Statements, disponible l'adresse www.alliedtelesis.com/

library. 8 Review Draft - July 13, 2020 Contents Preface ............................................................................................................................................................ 15 Safety Symbols Used in this Document .......................................................................................................... 16 Contacting Allied Telesis ................................................................................................................................. 17 Chapter 1: Product Description ...................................................................................................................19 Features ........................................................................................................................................................... 20 Hardware Components..................................................................................................................................... 23 Ethernet LAN Port ............................................................................................................................................ 25 Power Over Ethernet.................................................................................................................................. 25 Connector Type.......................................................................................................................................... 26 Speed......................................................................................................................................................... 26 Duplex Mode .............................................................................................................................................. 26 Automatic MDIX Detection ......................................................................................................................... 26 Cable Requirements .................................................................................................................................. 27 Maximum Distance..................................................................................................................................... 27 Port Pinouts................................................................................................................................................ 27 How to Power the Wireless Access Point......................................................................................................... 28 External AC/DC Power Adapter ................................................................................................................. 28 PoE+ or PoE++ Power Source .................................................................................................................. 28 Both AC/DC Power Adapter and PoE Power Source ................................................................................ 29 DC Connector for an External AC/DC Power Adapter ..................................................................................... 31 POWER On/Off Button ..................................................................................................................................... 32 LEDs................................................................................................................................................................. 33 Reset Button..................................................................................................................................................... 34 Management Tools........................................................................................................................................... 35 Web Browser.............................................................................................................................................. 35 Vista Manager EX and AWC Plug-in.......................................................................................................... 35 SNMP......................................................................................................................................................... 35 Chapter 2: Beginning the Installation ..........................................................................................................37 Reviewing Safety Precautions.......................................................................................................................... 38 Choosing a Site for the Wireless Access Point ................................................................................................ 41 Unpacking the Shipping Box ............................................................................................................................ 42 Chapter 3: Installing the Wireless Access Point ........................................................................................43 Installing the Wireless Access Point on a Table............................................................................................... 44 Overview to Installing the Wireless Access Point on a Wall or Ceiling............................................................. 48 Pre-fitting the Mounting Bracket on the Wireless Access Point........................................................................ 51 Installing the Mounting Bracket on a Wall or Ceiling ........................................................................................ 54 Connecting an Ethernet Cable to the Ethernet LAN Port ................................................................................. 58 Connecting the AC/DC Power Adapter ............................................................................................................ 59 Attaching the Wireless Access Point to the Wall Mounting Bracket ................................................................. 61 Installing an Anti-theft Device ........................................................................................................................... 63 Chapter 4: Managing the Wireless Access Point .......................................................................................65 Starting the First Management Session Without a DHCP Server .................................................................... 66 Starting the First Management Session with a Direct Connection ............................................................. 67 Starting the First Management Session Over a Network ........................................................................... 67 9 Review Draft - July 13, 2020 Contents Starting a Management Session ....................................................................................................................... 69 Appendix A: Technical Specifications ........................................................................................................ 71 Physical Specifications ..................................................................................................................................... 71 Environmental Specifications ............................................................................................................................ 71 Power Specifications......................................................................................................................................... 72 Input Power Specifications ......................................................................................................................... 72 External AC/DC Power Adapter Specifications .......................................................................................... 72 PoE+ or PoE++ Power Requirements ........................................................................................................ 72 Cable Specifications ......................................................................................................................................... 73 LAN Ports Specifications and Pinouts .............................................................................................................. 74 Port Specifications...................................................................................................................................... 74 Port Pinouts ................................................................................................................................................ 74 Appendix B: Regulatory Statements ........................................................................................................... 77 Federal Communication Commission Interference Statement.......................................................................... 78 Industry Canada Statement .............................................................................................................................. 80 Europe - EU Declaration of Conformity............................................................................................................. 82 Operating Frequencies and Maximum Transmission Power Levels .......................................................... 82 Radiation Exposure Statement................................................................................................................... 82 Importer ...................................................................................................................................................... 82 Appendix C: Radiation Patterns .................................................................................................................. 83 2.4GHz Antenna 1 ............................................................................................................................................ 84 2.4GHz Antenna 2 ............................................................................................................................................ 85 2.4GHz Antenna 3 ............................................................................................................................................ 86 2.4GHz Antenna 4 ............................................................................................................................................ 87 5GHz Antenna 1 ............................................................................................................................................... 88 5GHz Antenna 2 ............................................................................................................................................... 89 5GHz Antenna 3 ............................................................................................................................................... 90 5GHz Antenna 4 ............................................................................................................................................... 91 10 Review Draft - July 13, 2020 Figures Figure 1: Singapore IMDA Logo ........................................................................................................................ 7 Figure 2: Top View .......................................................................................................................................... 23 Figure 3: Front Panel....................................................................................................................................... 24 Figure 4: Rear Panel ....................................................................................................................................... 24 Figure 5: Powering the Access Point with an AC/DC Power Adapter ............................................................. 28 Figure 6: Powering the Access Point with a PoE+ or PoE++ Power Source................................................... 28 Figure 7: Powering the Access Point with Both an External AC/DC Adapter and a PoE+ or PoE++ Power Source ............................................................................................................................................................. 29 Figure 8: PWRADP-01 Power Adapter............................................................................................................ 31 Figure 9: Shipping Box Contents..................................................................................................................... 42 Figure 10: TQ6602 Wireless Access Point on a Table.................................................................................... 44 Figure 11: Installing the Bracket Screws ......................................................................................................... 45 Figure 12: Installing the Mounting Bracket ...................................................................................................... 45 Figure 13: Tightening Bracket Retaining Screw .............................................................................................. 46 Figure 14: Tightening the Bracket Screws....................................................................................................... 46 Figure 15: Orientations of the TQ6602 Wireless Access Point on a Wall ....................................................... 48 Figure 16: Invalid Orientation of the TQ6602 Wireless Access Point on a Wall.............................................. 48 Figure 17: TQ6602 Wireless Access Point on the Ceiling............................................................................... 49 Figure 18: Installing the Bracket Screws to the Wireless Access Point........................................................... 51 Figure 19: Attaching the Mounting Bracket on the Access Point..................................................................... 52 Figure 20: Adjusting the Screws on the Access Point ..................................................................................... 52 Figure 21: Removing the Wall Mounting Bracket from the Access Point ........................................................ 53 Figure 22: Marking the Holes for the Key-Hole Slots ...................................................................................... 54 Figure 23: Installing Two Screws..................................................................................................................... 55 Figure 24: Installing the Wall Mounting Bracket On the Screws...................................................................... 56 Figure 25: Pre-Drill Holes on Wall Mounting Bracket ...................................................................................... 56 Figure 26: Securing the Wall Mounting Bracket .............................................................................................. 57 Figure 27: Connecting an Ethernet Cable to the LAN Port.............................................................................. 58 Figure 28: Connecting the AC Power Cord to the PWRADP-01 Power Adapter ............................................ 59 Figure 29: Connecting an AC/DC Power Adapter to the DC IN Connector..................................................... 59 Figure 30: Connecting the Power Cord on the PWRADP-01 Power Adapter to an AC Source ...................... 60 Figure 31: DC Power On/Off Button ................................................................................................................ 60 Figure 32: Installing the Wireless Access Point on the Wall Mounting Bracket............................................... 61 Figure 33: Seating the Wireless Access Point on the Wall Mounting Bracket................................................. 62 Figure 34: Tightening the Wall Mounting Bracket Thumbscrew ...................................................................... 62 Figure 35: Kensington Lock Port ..................................................................................................................... 63 Figure 36: Log On Window.............................................................................................................................. 69 Figure 37: Pin Layout for RJ45 Connector on the Ethernet Port ..................................................................... 74 Figure 38: Axes on the TQ6602 Access Point................................................................................................. 83 11 Review Draft - July 13, 2020 List of Figures 12 Review Draft - July 13, 2020 Tables Table 1. LED Status Information .................................................................................................................... 33 Table 2. Physical Specifications ..................................................................................................................... 71 Table 3. Environmental Specifications ........................................................................................................... 71 Table 4. Input Power Specifications ............................................................................................................... 72 Table 5. External AC/DC Power Adapter Specifications ................................................................................ 72 Table 6. PoE Power Requirements on the Ethernet Port ............................................................................... 72 Table 7. LAN Port Specifications .................................................................................................................... 74 Table 8. MDI Pin Signals at 10/100Mbps ....................................................................................................... 74 Table 9. MDI-X Pin Signals at 10/100Mbps .................................................................................................... 75 Table 10. Connector Pinouts at 1/2.5/5Gbps ................................................................................................. 75 13 Review Draft - July 13, 2020 List of Tables 14 Review Draft - July 13, 2020 Preface This guide contains the hardware installation instructions for the indoor IEEE802.11ax TQ6602 Wireless Access Point. The preface contains the following sections:

Safety Symbols Used in this Document on page 16 Contacting Allied Telesis on page 17 15 Review Draft - July 13, 2020 Preface Safety Symbols Used in this Document This document uses the following conventions. Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a specific action may result in bodily injury. Warning Warnings inform you of hot surfaces. 16 Review Draft - July 13, 2020 Contacting Allied Telesis TQ6602 Wireless Access Point Installation Guide For assistance with this product, you can contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/support. You can find links for the following services on this page:

24/7 Online Support Enter our interactive support center to search for answers to your product questions in our knowledge database, check support tickets, learn about Return Merchandise Authorizations

(RMAs), and contact Allied Telesis technical experts. USA and EMEA phone support Select the phone number that best fits your location and customer type. Hardware warranty information Learn about Allied Telesis warranties and register your product online. Replacement Services Submit an RMA request via our interactive support center. Documentation View the most recent installation and user guides, software release notes, white papers, and data sheets for your products. Software Downloads Download the latest software releases for your managed products. For sales or corporate information, go to www.alliedtelesis.com/

purchase. 17 Review Draft - July 13, 2020 Preface 18 Review Draft - July 13, 2020 Chapter 1 Product Description The sections in this chapter describe the hardware components of the 802.11ax TQ6602 Wireless Access Point:

How to Power the Wireless Access Point on page 28 DC Connector for an External AC/DC Power Adapter on page 31 Features on page 20 Hardware Components on page 23 Ethernet LAN Port on page 25 POWER On/Off Button on page 32 LEDs on page 33 Reset Button on page 34 Management Tools on page 35 19 Review Draft - July 13, 2020 Chapter 1: Product Description Features 20 Hardware features include:

One 2.4GHz radio One 5GHz radio 4x4 MU-MIMO 2.4GHz Internal antennas 4x4 MU-MIMO 5GHz Internal antennas Transmission beamforming One 10/100Mbps/1/2.5/5Gbps Ethernet LAN port with RJ-45 IEEE 802.3at PoE+ Class 4 or IEEE 802.3bt PoE++ Class 5 One Reset button for rebooting the unit or restoring the default One On/Off button for the AC/DC power adapter connector LEDs for the 2.4GHz and 5GHz radios, Ethernet LAN port, and connector powered device settings power Ceiling, wall, or table installation Kensington lock port One Console RJ-45 port for factory use only Software features include:

IEEE802.11a/b/g/n/ac/ax Multi-channel (cell operation) Channel Blankets (single-channel operation) Multi-channel and Channel Blanket hybrid operation Orthogonal Frequency Division Multiple Access (OFDMA) Manual or automatic radio channel selection Sixteen virtual access points (VAPs) per radio and thirty two VAPs per access point Quality of Service (QoS) ingress and egress queues Fast roaming (IEEE 802.11v/k/r) Control of radio transmission power Dynamic frequency selection Band steering WiFi multimedia (WMM) for prioritizing traffic Client filtering by MAC addresses Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Wireless Distribution System (WDS) bridges Dynamic Host Control Protocol (DHCP) client Network Time Protocol (NTP) client System log Syslog client Autonomous Management Framework (AMF) Guest node Security and encryption include:

Open system Shared key authentication Static WEP with 64/128/256 bit encryption (IEEE 802.11a/b/g only) WPA Personal or Enterprise security with auto, CCMP (AES), or WPA2 Personal or Enterprise security with auto, CCMP (AES), or WPA3 Personal or Enterprise security with CCMP (AES/CNSA) TKIP encryption TKIP encryption encryption Frequency range and bandwidth for the 2.4GHz radio include:

Frequency range and bandwidth for the 5GHz radio include:

2.412 to 2.484GHz 20/40MHz 5.150 to 5.850GHz 20/40/80/80+80MHz Features of the Ethernet LAN port include:

10Mbps (IEEE 802.3), 100Mbps (IEEE 802.3u), 1000Mbps (IEEE 802.3ab), 2.5Gbps, and 5Gbps (IEEE 802.3bz) PoE+ (IEEE 802.3at) or PoE++ (IEEE 802.3bt) Flow control (IEEE 802.3x) VLAN tagging (IEEE 802.1Q) Auto-Negotiation for speed and duplex mode Auto-MDI/MDIX at 10/100Mbps Management options include:

On-board web browser management interface Vista Manager EX with Automous Wave Controller (AWC) plug-in or AWC lite plug-in 21 Review Draft - July 13, 2020 Chapter 1: Product Description Autonomous Management Framework (AMF) Security or Security Mini (AMF-Sec mini) SNMPv1 and v2c Note For a complete list of features, refer to the TQ6602 Wireless Access Point User Guide or the products data sheet. 22 Review Draft - July 13, 2020 Hardware Components TQ6602 Wireless Access Point Installation Guide The top view of the TQ5403 Access Point is illustrated in Figure 1. Back Edge Front Edge LAN (PoE) Port LED 2.4GHz Radio LED PWR/SYS (Power/

System) LED 5GHz Radio LED Figure 1. Top View 23 Review Draft - July 13, 2020 Chapter 1: Product Description The front panel is illustrated in Figure 2. Mounting Bracket Thumbscrew Hole Figure 2. Front Panel The rear panel is shown in Figure 3. Kensington Lock Port Reset Button Ethernet LAN PoE+ or POE++

Port POWER On/Off Button for DC IN Connector Console Serial Port DC IN Connector for AC/DC Adapter Figure 3. Rear Panel Note The Console Serial port is for manufacturing purposes only. 24 Review Draft - July 13, 2020 Ethernet LAN Port TQ6602 Wireless Access Point Installation Guide The wireless access point has one Ethernet LAN port on the rear panel, with these operational properties:

10Mbps (IEEE 802.3), 100Mbps (IEEE 802.3u), 1000Mbps (IEEE 802.3ab), 2.5Gbps, and 5Gbps (IEEE 802.3bz) Flow control (IEEE 802.3x) VLAN tagging (IEEE 802.1Q) Auto-Negotiation for speed and duplex mode Auto-MDI/MDIX at 10/100Mbps The port has the following functions:

You use it to connect the wireless access point to a device on your wired network, such as Ethernet switch or router. The port makes it possible for wireless clients of the wireless network to gain access to the wired network. The Ethernet LAN port can also be used to provide the electrical power to the device. The wireless access point is a PoE powered device, meaning it can be powered by a PoE power source on the port. A PoE power source can be a PoE router or switch. such as the x320-10GH Switch from Allied Telesis. Electrical power is transmitted to the wireless access point by the power source over the same network cable that carries the network traffic. Power Over Ethernet You can power the wireless access point as either a PoE+ Class 4 or PoE++ Class 5 device on the LAN port. Powering the device with PoE requires connecting the LAN port to a PoE source device. If you operate the device as a PoE+ Class 4 device, Allied Telesis recommends disabling one of the following features to ensure the wireless access point has adequate operating power:

One radio or IEEE 802.11ax Note If you connect the device to a PoE+ Class 4 power source and do not disable one of the above features, the devices operations may be unpredictable. 25 Review Draft - July 13, 2020 Chapter 1: Product Description You can also power the device with an external AC/DC adapter, such as the PWRADP-01 Power Adapter, to . Refer to How to Power the Wireless Access Point on page 28. Connector Type The LAN port has an eight-pin RJ45 connector. The port uses four pins in the connector at 10/100 Mbps and all eight pins at higher speeds. Refer to the tables in Port Pinouts on page 74 for the pin assignments. Speed The LAN port can operate at 10/100Mbps/1/2.5/5Gbps. The speed is set automatically with Auto-Negotiation. You cannot disable Auto-Negotiation on the port. Note You should connect the LAN port to a network device that also supports Auto-Negotiation. The LAN port operates at 10Mbps if it is connected to a network device does not support Auto-Negotiation. This may result in reduced network performance. Duplex Mode The LAN port can operate in either half- or full-duplex mode at 10/100Mbps, and full-duplex mode at higher speeds. The port is IEEE 802.3u-compliant and use Auto-Negotiation to set the duplex mode. You cannot disable Auto-Negotiation on the port. Note You should connect the LAN port to a network device that also supports Auto-Negotiation for duplex mode. If connected to a network device that does not support Auto-Negotiation, it operates at half-duplex mode. This will result in a duplex mode mismatch if the network device is operating at full duplex. This may result in reduced network performance. Automatic MDIX Detection The LAN port is IEEE 802.3ab compliant. It features automatic MDIX detection when operating at 10/100Mbps. (Automatic MDIX detection does not apply to higher speeds.) This feature automatically configures the port to MDI or MDI-X depending on the wiring configuration of the port on the network device where it is connected. You cannot disable automatic MDIX detection. For automatic MDIX detection to work properly, this feature must also be present on the network device. The LAN port defaults to MDIX if it is connected to a network device that does not support automatic MDIX detection. 26 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Cable Requirements Maximum Distance Port Pinouts The minimum cable requirements for the port are listed here. 10/100 Mbps: Standard TIA/EIA 568-B-compliant Category 3 shielded or unshielded cabling. 1/2.5/5Gbps: Standard TIA/EIA 568-A-compliant Category 5 or TIA/

EIA 568-B-compliant Enhanced Category 5 (Cat 5e) shielded or unshielded cabling. The LAN port has a maximum operating distance of 100 meters (328 feet). Refer to Table 8 on page 74 for the port pinouts of the LAN port when it is operating at 10/100Mbps in the MDI configuration and Table 9 on page 75 for the MDI-X configuration. Refer to Table 10 on page 75 for the port pinouts when the port is operating at 1/2.5/5Gbps. 27 Review Draft - July 13, 2020 Chapter 1: Product Description How to Power the Wireless Access Point There are three ways to power the wireless access point. External AC/DC Power Adapter, next PoE+ or PoE++ Power Source on page 28 Both AC/DC Power Adapter and PoE Power Source on page 29 Note The input power specifications of the wireless access point are listed in Table 4 on page 72 in Appendix A, Technical Specifications on page 71. External AC/DC Power Adapter One way to power the wireless access point is with an external AC/DC power adapter, such as the PWRADP-01 Power Adapter from Allied Telesis. Refer to Figure 4. The power adapter is connected to the DC IN connector on the rear panel of the wireless access point. Figure 4. Powering the Access Point with an AC/DC Power Adapter PoE+ or PoE++

Power Source The wireless access point is a PoE powered device. It can be powered by a PoE power source on its Ethernet LAN port. An example of a PoE power source is the x320-10GH PoE++ Ethernet Switch from Allied Telesis. Refer to Figure 5. Figure 5. Powering the Access Point with a PoE+ or PoE++ Power Source 28 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide The wireless access point can operate as a PoE+ Class 4 or PoE++ Class 5 device. Here are the guidelines:

The access points supports all features when powered as a Class 5 device by a PoE++ power source. The device can also be powered by a PoE+ power source that supports Class 4 devices. However, to ensure proper operation, Allied Telesis recommends disabling one of the following features to ensure adequate operational power:

- One radio or

- IEEE802.11ax Finally, the device can be powered by both an external AC/DC power adapter and a PoE+ or PoE++ power source. Refer to Figure 6. Both AC/DC Power Adapter and PoE Power Source Figure 6. Powering the Access Point with Both an External AC/DC Adapter and a PoE+ or PoE++ Power Source Here are the operating rules of the wireless access point when connected to both an AC/DC power adapter and a PoE power source:

The two power sources are not load sharing. The power adapter is the primary power source and PoE is held in reserve. The LAN port operates as a standard Ethernet LAN port, with PoE blocked. If the power adapter stops providing power, the wireless access point automatically changes to PoE on the LAN port as its power source. 29 Review Draft - July 13, 2020 Chapter 1: Product Description If the power adapter resumes providing power, the wireless access point automatically switches back to the power adapter as its primary power source. PoE on the LAN port is blocked and returned to reserve status. 30 Review Draft - July 13, 2020 DC Connector for an External AC/DC Power Adapter TQ6602 Wireless Access Point Installation Guide The DC IN connector is for an external AC/DC power adapter, such as the PWRADP-01 Power Adapter from Allied Telesis, shown in Figure 7. Figure 7. PWRADP-01 Power Adapter You can power the wireless access point with either an external power adapter on the DC IN connector or a PoE+ or PoE++ power source on the Ethernet LAN port. You can also power it with both power sources. Refer to How to Power the Wireless Access Point on page 28 and Power Specifications on page 72. Note Use only power sources that are UL Listed (QQGQ or EPBU), TUV Licensed, or other Safety Agencies approved, and that are suitable for country of use. 31 Review Draft - July 13, 2020 Chapter 1: Product Description POWER On/Off Button The POWER On/Off button on the rear panel powers on or off the DC IN connector for an external AC/DC power adapter. Here are the button settings:

In - The DC IN connector is On, allowing power from the AC/DC Out - The DC IN connector is Off, blocking power from the AC/DC adapter. adapter. Here are the guidelines:

If the wireless access point is powered by both an AC/DC power adapter and a PoE power source, turning off the DC IN connector shuts off power from the adapter. The access point automatically switches over to PoE for power. If the wireless access point is powered only by an AC/DC power adapter, turning off the DC IN connector shuts off the device. 32 Review Draft - July 13, 2020 LEDs TQ6602 Wireless Access Point Installation Guide The LEDs on the top panel display status information. They are defined in Table 1. Table 1. LED Status Information LED State Description Green Red Off Green Off Green Off Off Green Power Blinking Red LAN Blinking Green 2.4GHz Wi-Fi 5 GHz Wi-Fi The access point is powered ON and operating normally. The device is booting up or has encountered a fault condition. The access point is upgrading its firmware. The access point is not receiving power. The port has established a link to a network device. The port is transmitting or receiving data. The port has not established a link to a network device. The 2.4GHz Radio1 is enabled. The 2.4GHz Radio1 is disabled. The 5GHz Radio2 is enabled. The 5GHz Radio2 is disabled. 33 Review Draft - July 13, 2020 Chapter 1: Product Description Reset Button The wireless access point has a Reset button on the rear panel. The button has two functions. The selected function depends on how long the button is pressed:

One to five seconds: Reboots the wireless access point. Five to ten seconds: Restores the default values to all settings to the wireless access point, including manager name and password. You can enable or disable the reset button with the management software. The default setting for the button is enabled. If the access point is installed in a public area, you should disable it to prevent unauthorized individuals from resetting the device and interrupting network operations. 34 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Management Tools Web Browser The wireless access point supports the following management tools. The wireless access point has a web browser management interface for configuring the device from your management workstation. The web browser interface allows you to manage one unit at a time and supports both non-secure HTTP and secure HTTPS management sessions. The default is HTTP. The product has been tested with Microsoft Internet Explorer version 11 or later, Microsoft Edge, and Chrome. Vista Manager EX and AWC Plug-in The wireless access point supports Vista Manager and the Autonomous Wave Control (AWC) plug-in. Configuring and monitoring large numbers of devices is simplified with AWC because you can add multiple devices to management groups and manage them as one unit. The application can also monitor the operations of the wireless access points and automatically adjust operating properties to optimize the performance of your wireless network. Note The Channel Blanket feature in the TQ6602 Access Point requires Vista Manager EX and the AWC plug-in. Note The TQ6602 Wireless Access Point requires Vista Manager EX and AWC plug-in version 2.5.1 or later. SNMP You can use SNMPv1 or v2c to view the parameter settings of the devices. The MIB is available from the Allied Telesis web site. For instructions on how to configure the unit for SNMP, refer to the TQ5403 Series Management Software Users Guide. 35 Review Draft - July 13, 2020 Chapter 1: Product Description 36 Review Draft - July 13, 2020 Chapter 2 Beginning the Installation This chapter contains the following sections:

Reviewing Safety Precautions on page 38 Choosing a Site for the Wireless Access Point on page 41 Unpacking the Shipping Box on page 42 Note The non-US models of this product have a country code setting that has to be set during the initial management session of the units. The setting ensures that the units operate in compliance with the laws and regulations of your country or region. For the US model, the country code is preset and cannot be changed. Per FCC regulations, the country code setting for all WiFi products marketed in the US have to be fixed to US operational channels only. 37 Review Draft - July 13, 2020 Chapter 2: Beginning the Installation Reviewing Safety Precautions Please review the following safety precautions before installing the access point. Important: Safety statements that have the symbol are translated into multiple languages in the Translated Safety Statements document, which is available at www.alliedtelesis.com/library. Remarque: Les consignes de scurit portant le symbole sont traduites dans plusieurs langues dans le document Translated Safety Statements, disponible l'adresse www.alliedtelesis.com/library. Warning To prevent electric shock, do not remove the cover. No user-serviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician. To avoid the possibility of electric shock, disconnect electric power to the product before connecting or disconnecting the LAN cables. E1 Warning Do not work on equipment or cables during periods of lightning activity. E2 Warning All Countries: Install product in accordance with local and National Electrical Codes. E8 Warning Only trained and qualified personnel are allowed to install or to replace this equipment. E14 Warning To reduce the risk of electric shock, the PoE ports on this product must not connect to cabling that is routed outside the building where this device is located. E40 38 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Warning This equipment shall be installed in a Restricted Access location. E45 Warning FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Note The access point must be powered by:

1. A UL listed external AC/DC power supply suitable for use at Tma 50oC, a maximum operating altitude of 3000 m or higher, and whose output meets separated extra-low voltage (SELV), limited power sources (LPSs) and is rated 12 VDC, 4.0 A, Refer to Table 5, External AC/DC Power Adapter Specifications on page 72. OR 2. By Power over Ethernet through a UL listed ITE. Caution Air vents must not be blocked and must have free access to the room ambient air for cooling. E6 Warning An operational unit can be hot. Exercise caution when handling with unprotected hands. Warning Operating Temperature. This product is designed for a maximum ambient temperature of 50C (122 F) E7. Warning To reduce the risk of electric shock, the PoE port on this product must not connect to cabling that is routed outside the building where this device is located. E40 39 Review Draft - July 13, 2020 Chapter 2: Beginning the Installation Warning This equipment is intended for indoor use only. E95 Note If you are not using PoE to power to unit, use only an approved AC/

DC adapter. Refer to External AC/DC Power Adapter Specifications on page 72. Caution The unit does not contain serviceable components. Please return damaged units for servicing. E42 Note You should verify that your PoE network adheres to the standards of a separated extra-low voltage (SELV) circuit before using the PoE feature on the wireless access point. 40 Review Draft - July 13, 2020 Choosing a Site for the Wireless Access Point TQ6602 Wireless Access Point Installation Guide Observe these requirements when planning the installation of the wireless access point:

The ceiling or wall mounting surface should be of proper material to accommodate the screws and strong enough to support the weight of the wireless access point and cables. (Refer to Table 2 on page 71 for product weight.) Verify that the Ethernet cable is long enough to connect to its destination port. If the wireless access point will be powered by an AC/DC adapter, verify that an AC power outlet is within six feet of the planned installation site. The site should allow for easy access to the Ethernet port on the device, so that you can easily connect and disconnect the cable. The site should allow for adequate air flow around the unit and through the cooling vents on the bottom panel. The site should not expose the device to moisture or water. The site should be a dust-free environment. The site should not expose the twisted pair cabling to sources of electrical noise, such as radio transmitters, broadband amplifiers, power lines, electric motors, and fluorescent fixtures. Do not place objects on top of the device. If installing the device in a wiring or utility box, verify that there is adequate airflow to prevent overheating. 41 Review Draft - July 13, 2020 Chapter 2: Beginning the Installation Unpacking the Shipping Box The contents of the shipping box are shown in Figure 8. Verify and inspect the contents. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. Note Store the packaging material in a safe location. Please use the original shipping material if you need to return the device to Allied Telesis. TQ6602 Wireless Access Point Wall Mounting Bracket Two M5 x 8mm, Pan-head Screws Figure 8. Shipping Box Contents 42 Review Draft - July 13, 2020 Chapter 3 Installing the Wireless Access Point This chapter contains the installation procedures for the TQ6602 Wireless Access Point. The procedures are detailed in the following sections:

Installing the Wireless Access Point on a Table on page 44 Overview to Installing the Wireless Access Point on a Wall or Ceiling Pre-fitting the Mounting Bracket on the Wireless Access Point on on page 48 page 51 Installing the Mounting Bracket on a Wall or Ceiling on page 54 Connecting an Ethernet Cable to the Ethernet LAN Port on page 58 Connecting the AC/DC Power Adapter on page 59 Attaching the Wireless Access Point to the Wall Mounting Bracket on page 61 Installing an Anti-theft Device on page 63 43 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point Installing the Wireless Access Point on a Table Figure 9 Shows the wireless access point on a table. Figure 9. TQ6602 Wireless Access Point on a Table You need the following items to install the access point on a table:

TQ6602 Wireless Access Point Wall mounting bracket (provided)

(provided) One Ethernet cable Two screws to attach the wall mounting bracket to the access point External AC/DC power supply (Optional if using PoE. Required if not using PoE or for redundant power.) Kensington lock (optional) Note Allied Telesis recommends installing the wall mounting bracket on the bottom panel of the wireless access point when installing the device on a table. The bracket will facilitate airflow through the cooling fins beneath the device. Note Please see Reviewing Safety Precautions on page 38 and Choosing a Site for the Wireless Access Point on page 41 before installing the product. Perform the following steps to install the wireless access point on a table:

1. Place the wireless access point upside down on a table. 44 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide 2. Install the two screws included with the device in the bottom panel. Leave the screws loose enough so that you can slide the bracket under the screw heads. Refer to Figure 10. Figure 10. Installing the Bracket Screws 3. Slide the mounting bracket beneath the screws. Refer to Figure 11. Figure 11. Installing the Mounting Bracket 45 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point 4. Tighten the bracket retaining screw. Refer to Figure 12. Figure 12. Tightening Bracket Retaining Screw 5. Tighten the two bracket screws. Refer to Figure 13. Figure 13. Tightening the Bracket Screws 6. Turn the wireless access point upright on the table. 7. Place the wireless access point at the selected location. 46 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide 8. Go to one the following procedures Connecting an Ethernet Cable to the Ethernet LAN Port on page 58. Connecting the AC/DC Power Adapter on page 59. Installing an Anti-theft Device on page 63. 47 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point Overview to Installing the Wireless Access Point on a Wall or Ceiling You can install the wireless access point on a wall with the front panel pointing to the left, down. or right. Refer to Figure 14. Figure 14. Orientations of the TQ6602 Wireless Access Point on a Wall Do not install the device with the front panel facing up. Refer to Figure 15. Figure 15. Invalid Orientation of the TQ6602 Wireless Access Point on a Wall 48 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Figure 16 shows the device installed on a ceiling. Figure 16. TQ6602 Wireless Access Point on the Ceiling Here are the procedures for installing the wireless access point on a wall or ceiling:

Pre-fitting the Mounting Bracket on the Wireless Access Point on Installing the Mounting Bracket on a Wall or Ceiling on page 54 Connecting an Ethernet Cable to the Ethernet LAN Port on page 58 Connecting the AC/DC Power Adapter on page 59 Attaching the Wireless Access Point to the Wall Mounting Bracket on page 51 page 61 Installing an Anti-theft Device on page 63 Note Please see Reviewing Safety Precautions on page 38 and Choosing a Site for the Wireless Access Point on page 41 before installing the product. Depending on the installation location, it may be easier to connect the network cables and power adapter to the wireless access point before installing it on the wall or ceiling. You need the following items to install the wireless access point on a ceiling or wall:

Two screws to attach the access point to the mounting bracket TQ6602 Wireless Access Point

(provided) Wall mounting bracket (provided) Four (4) M4, 25.0 mm flat-head wood screws and anchors for fastening the mounting bracket (not provided) Phillips head screwdriver (not provided) 49 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point Pencil (not provided) External AC/DC power supply (Optional if using PoE. Required if not using PoE or for redundant power.) Kensington lock (optional and not provided) Note The four Phillips head M4 screws/anchors, the Phillips head screwdriver, pencil, external AC/DC power supply and Kensington lock are not included with the product. 50 Review Draft - July 13, 2020 Pre-fitting the Mounting Bracket on the Wireless Access Point TQ6602 Wireless Access Point Installation Guide To pre-fit the mounting bracket on the wireless access point, perform the following procedure:

1. Place the wireless access point upside down on a table. 2. Install the two screws (provided) in the bottom side of the access point chassis. Leave the screws loose enough so that you can slide the bracket under the screw heads. Refer to Figure 17. Figure 17. Installing the Bracket Screws to the Wireless Access Point 3. Slide the wall mounting bracket beneath the screws. Refer to Figure 18 on page 52. 51 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point Figure 18. Attaching the Mounting Bracket on the Access Point 4. Tighten the screws so that they touch the wall mounting bracket, and then loosen them by approximately 1/4 turn. Refer to Figure 19. Note Adjust the screws so they are loose enough for you to remove the wall mounting bracket, but tight enough to prevent the access point from rattling against the bracket. Figure 19. Adjusting the Screws on the Access Point 52 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide 5. Remove the wall mounting bracket from the access point. Refer to Figure 20. Figure 20. Removing the Wall Mounting Bracket from the Access Point 6. Go to Installing the Mounting Bracket on a Wall or Ceiling on page 54. 53 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point Installing the Mounting Bracket on a Wall or Ceiling To install the mounting bracket on a wall of ceiling, perform the following procedure:

1. Choose the location and orientation for the access point on the wall or ceiling. Refer to Figure 14 on page 48. 2. Position the mounting bracket at the selected location and orientation for the access point. Consider the following guidelines. The thumbscrew on the mounting bracket is where the front panel of the access point will be. The ports and connectors are on the back panel, away from the thumbscrew. 3. With a pencil, mark the wall or ceiling with the two key-hole slots of the bracket. Refer to Figure 21. Figure 21. Marking the Holes for the Key-Hole Slots 4. Pre-drill the two marked locations for the keyhole slots on the ceiling or wall. 5. Install two M4 screws and anchors (if required). Leave the screws loose enough so that the bracket can slide under the screw heads. Refer to Figure 22 on page 55. 54 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Note For a wooden wall or ceiling, use M4, 25.0 mm flat-head wood screws and anchors, if required. The screws and anchors are not provided with the wireless access point. Figure 22. Installing Two Screws 6. Insert the openings of the bracket key-hole slots under the two screw heads and slide the bracket into the narrow end of the key-hole slot openings. Refer to Figure 23 on page 56. 55 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point Figure 23. Installing the Wall Mounting Bracket On the Screws 7. Tighten the screws snugly onto the bracket. 8. To secure the mounting bracket, pre-drill holes through the two bracket mounting holes opposite the key-hole slots. Refer to Figure 24. Figure 24. Pre-Drill Holes on Wall Mounting Bracket 56 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide 9. Install and tighten two M4 screws (not provided) in the holes prepared in Step 8. Refer to Figure 25. The bracket installation is now complete. Figure 25. Securing the Wall Mounting Bracket 10. Do one of the following:

Depending on the installation location, it may be easier to connect the Ethernet cable and optional AC/DC power adapter to the wireless access point before installing it on the wall of ceiling. If that is the case in your installation, continue with the installation by going to Connecting an Ethernet Cable to the Ethernet LAN Port on page 58. To install the wireless access point on the wall of ceiling before attaching cables, go to Attaching the Wireless Access Point to the Wall Mounting Bracket on page 61. 57 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point Connecting an Ethernet Cable to the Ethernet LAN Port This section contains the procedure for connecting an Ethernet cable to the LAN port. For information on cable specifications, refer to Cable Requirements on page 27. Please review the following guidelines before connecting the Ethernet cable:

If you are installing the wireless access point on a ceiling or wall, you might find it easier to connect the cable before placing the unit on the wall mounting bracket. To power the wireless access point with PoE, connect the LAN port to a PoE source device. For power specifications, refer to PoE+ or PoE++ Power Requirements on page 72. To connect the network cable, perform the following procedure:

1. Connect an Ethernet cable into the RJ-45 LAN port. Refer to Figure 26. Note If the other end of the Ethernet cable is already connected to a PoE source device, the wireless access point begins to power on and initialize its management software. Figure 26. Connecting an Ethernet Cable to the LAN Port 2. Connect the other end of the Ethernet cable to a network Ethernet device, such as an Ethernet switch or router. 3. Do one of the following:

If the access point will be power by PoE only, without an AC/DC power adapter, go to Attaching the Wireless Access Point to the Wall Mounting Bracket on page 61. To power the access point with an external AC/DC power adapter, go to Connecting the AC/DC Power Adapter. 58 Review Draft - July 13, 2020 Connecting the AC/DC Power Adapter TQ6602 Wireless Access Point Installation Guide You can power the wireless access point with PoE on the LAN port or an AC/DC power adapter, or both. Refer to How to Power the Wireless Access Point on page 28. To connect a power adapter to the wireless access point, perform the following procedure:

1. If you purchased the PWRADP-01 Power Adapter, connect the AC power cord to the power adapter. Refer to Figure 27. Figure 27. Connecting the AC Power Cord to the PWRADP-01 Power Adapter 2. Plug the DC cable from the power adapter into the DC IN connector on the wireless access point. Refer to Figure 28. Figure 28. Connecting an AC/DC Power Adapter to the DC IN Connector 59 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point 3. Connect the power adapter into an appropriate AC power source. Refer to Figure 29. Figure 29. Connecting the Power Cord on the PWRADP-01 Power Adapter to an AC Source 4. Push the DC Power On/Off Button on the wireless access point to the IN position to turn on the DC connector. Refer to Figure 30. Note The DC Power Button controls the DC connector. It does not control PoE on the LAN port. Figure 30. DC Power On/Off Button The wireless access point begins to initialize its management software. The process takes about one minute to complete. 5. Go to Attaching the Wireless Access Point to the Wall Mounting Bracket on page 61. 60 Review Draft - July 13, 2020 Attaching the Wireless Access Point to the Wall Mounting Bracket TQ6602 Wireless Access Point Installation Guide To attach the wireless access point to the wall mounting bracket on the wall or ceiling, perform the following procedure:

1. Align the bottom of the access point over the bracket so that the two screws on the bottom of the device fit into the bracket keyholes. Refer to Figure 31. (The two screws are installed in Pre-fitting the Mounting Bracket on the Wireless Access Point on page 51.) Figure 31. Installing the Wireless Access Point on the Wall Mounting Bracket 2. Slide the wireless access point until its screws are seated in the bracket keyhole slots and the bracket thumbscrew is aligned with the screw hole on the front panel. Refer to Figure 32 on page 62. 61 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point Figure 32. Seating the Wireless Access Point on the Wall Mounting Bracket 3. Tighten the thumbscrew to secure the wireless access point to the wall mounting bracket. Refer to Figure 33. Figure 33. Tightening the Wall Mounting Bracket Thumbscrew 4. Go to Installing an Anti-theft Device on page 63 or Chapter 4, Managing the Wireless Access Point on page 65. 62 Review Draft - July 13, 2020 Installing an Anti-theft Device TQ6602 Wireless Access Point Installation Guide Installation of an anti-theft cable/lock is optional. The access point has a lock port that is compatible with a Kensington lock. The lock port can be used to physically secure the device to a table, wall, or a ceiling. Note Anti-theft devices are not available from Allied Telesis. Follow the instructions provided with the vendors anti-theft device for the installation. Refer to Figure 34 for the Kensington lock port location. RESET CONSOLE

(POE) LAN DC IN POWER Kensington Lock Port Figure 34. Kensington Lock Port If you are installing the wireless access point on a wall or ceiling and have not installed it on the mounting bracket yet, go to Attaching the Wireless Access Point to the Wall Mounting Bracket on page 61. Otherwise, go to Chapter 4, Managing the Wireless Access Point on page 65. 63 Review Draft - July 13, 2020 Chapter 3: Installing the Wireless Access Point 64 Review Draft - July 13, 2020 Chapter 4 Managing the Wireless Access Point This chapter contains the following sections:

Starting the First Management Session Without a DHCP Server on page 66 Starting a Management Session on page 69 65 Review Draft - July 13, 2020 Chapter 4: Managing the Wireless Access Point Starting the First Management Session Without a DHCP Server After you install and power on the wireless access point, it queries the subnet on the LAN port for a DHCP server. If a DHCP server responds to its query, the unit uses the IP address the server assigns to it. If there is no DHCP server, the access point uses the default IP address 192.168.1.230. If your network has a DHCP server, use the IP address the server assigns it to it to start the management session. For directions, refer to Starting a Management Session on page 69 If your network does not have a DHCP server, you can start the first management session by establishing a direct connection between your computer and the unit by connecting an Ethernet cable to the Ethernet port on the computer and the LAN1 port on the access point. This procedure requires changing the IP address on your computer to make it a member of the same subnet as the default IP address on the access point. The first management session can also be performed while the device is connected to your network. However, If your network does not have a DHCP server, you still have to change the IP address of your computer to match the subnet of the default address of the access point. Furthermore, if your network is divided into virtual LANs (VLANs), you have to be sure to connect the access point and your computer to ports on an Ethernet switch that are members of the same VLAN. The instructions for starting the first management session are found in the following sections:

Starting the First Management Session with a Direct Connection on page 67 Starting the First Management Session Over a Network on page 67 Note The first management session of the access point has to be conducted through the LAN port because the default setting for the radios is off. 66 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Starting the First Management Session with a Direct Connection To start the management session with a direct Ethernet connection between your computer and the LAN port on the access point, perform the following procedure:

Note If the access point is powered only with PoE, you cannot perform this procedure because it requires a direct connection between your computer and the LAN port on the access point. Instead, perform Starting the First Management Session Over a Network on page 67. 1. Connect one end of a network cable to the LAN port on the access point and the other end to the Ethernet network port on your computer. 2. Change the IP address on your computer to 192.168.1.n, where n is a number from 1 to 254, but not 230. Refer to the documentation that accompanies your computer for instructions on how to set the IP address. 3. Set the subnet mask on your computer to 255.255.255.0. 4. Power on the access point. 5. Start the web browser on your computer. 6. Enter the IP address 192.168.1.230 in the URL field of the browser and press the Enter key. You should now see the login window, shown in Figure 35 on page 69. 7. Enter manager for the user name and friend for the password. The user name and password are case-sensitive. 8. Click the Login button. This procedure explains how to start the first management session on the access point when the LAN port is connected to an Ethernet switch on a network that does not have a DHCP server. To start the management session, perform the following procedure:

1. If your network has VLANs, check to be sure that your computer and the access point are connected to ports on the Ethernet switch that are members of the same VLAN. This might require accessing the management software on the switch and listing the VLANs and their port assignments. For example, if the access point is connected to a port that is a member of the Sales VLAN, your computer must be connected to a port that is also a member of that VLAN. If your network is small and does not have VLANs or routers, you can connect your computer to any port on the Ethernet switch. 67 Starting the First Management Session Over a Network Review Draft - July 13, 2020 Chapter 4: Managing the Wireless Access Point 2. Change the IP address on your computer to 192.168.1.n, where n is a number from 1 to 254, but not 230. Refer to the documentation that accompanies your computer for instructions on how to set the IP address. 3. Set the subnet mask on your computer to 255.255.255.0. 4. Power on the access point. 5. Start the web browser on your computer. 6. Enter the IP address 192.168.1.230 in the URL field of the browser and press the Return key. You should now see the logon window, shown in Figure 35 on page 69. 7. Enter manager for the user name and friend for the password. The user name and password are case-sensitive. 8. Click the Login button. 68 Review Draft - July 13, 2020 Starting a Management Session TQ6602 Wireless Access Point Installation Guide This section explains how to start a management session on the access point from your management workstation, using a web browser. The procedure assumes that the access point has already been assigned an IP address, either manually or from a DHCP server. Note If the access point is using its default address 192.168.1.230, refer to Starting the First Management Session Without a DHCP Server on page 66 for instructions. To start a management session on the access point, perform the following procedure:

1. Open the web browser on your management workstation. 2. Enter the IP address of the access point in the URL field of the web browser. Note Precede the IP address with HTTPS:// if the access point is already configured for HTTPS management. The default is HTTP management. You should now see the log on window in Figure 35. Figure 35. Log On Window 69 Review Draft - July 13, 2020 Chapter 4: Managing the Wireless Access Point Note If you use HTTPS management, your web browser might display a warning message stating that the site certificate is invalid. If this occurs, select an appropriate option to continue to the web site. To avoid the message in future management sessions, make the web site a trusted site in your web browser. 3. Enter the user name and password for the unit. The default values are manager for the user name and friend for the password. The user name and password are case-sensitive. 4. Click the Login button. 70 Review Draft - July 13, 2020 Appendix A Technical Specifications Physical Specifications Environmental Specifications This appendix contains the specifications for the TQ6602 and TQm5403 Wireless Access Points in the following sections:

Physical Specifications Environmental Specifications Power Specifications on page 72 Cable Specifications on page 73 LAN Ports Specifications and Pinouts on page 74 Table 2. Physical Specifications Parameter Specification Dimensions (W x D x H) 205 mm X 225 mm X 51 mm

(8.07 in. x 8.86 in. x 2.01 in.) Weight without mounting bracket tbd g (tbd lbs) Weight with mounting bracket tbd g (tbd lbs) Table 3. Environmental Specifications Parameter Specification Operating Temperature when powered by AC/DC adapter Operating Temperature when powered by PoE power source 0 C to 50 C (32 F to 122 F) 0 C to 50 C (32 F to 122 F) Storage Temperature

- 25 C to 70 C (- 13 F to 158 F) Operating Humidity 5% to 90% non-condensing Storage Humidity 5% to 95% non-condensing Maximum Operating Altitude 3000 m (9843 ft) 71 Review Draft - July 13, 2020 Appendix A: Technical Specifications Power Specifications Input Power Specifications Table 4 lists the power requirements of the TQ6602 Wireless Access Point. Table 4. Input Power Specifications Parameter Specification Rated Input Voltage

+12 VDC Maximum Input Current Average Input Current 4A tbd A External AC/DC Power Adapter Specifications Table 5 lists the power requirements for an external AC/DC power adapter. Table 5. External AC/DC Power Adapter Specifications Parameter Input Voltage Range Input Frequency Rated Output Voltage Rated Output Current Specification 100~240 VAC 50 - 60 Hz

+12 VDC 0-4.0A Note Allied Telesis recommends the PWRADP-01 AC/DC power adapter. It is UL Listed and fully compatible with the above specifications, while meeting the standards of a separated extra-low voltage

(SELV) product. The adapter is sold separately. PoE+ or PoE++

Power Requirements Table 6 lists the Poe+ and PoE++ specifications for the Ethernet port. Table 6. PoE Power Requirements on the Ethernet Port Parameter Specification Power PoE+ Device Classification PoE++ Device Classification tbd watts Class 4 Class 5 72 Review Draft - July 13, 2020 Cable Specifications TQ6602 Wireless Access Point Installation Guide The minimum cable requirements for the Ethernet port are listed here. 10/100Mbps: Standard TIA/EIA 568-B-compliant Category 3 shielded or unshielded cabling. 1/2.5/5Gbps: Standard TIA/EIA 568-A-compliant Category 5 or TIA/

EIA 568-B-compliant Enhanced Category 5 (Cat 5e) shielded or unshielded cabling. The maximum operating distance is 100 meters (328 feet). 73 Review Draft - July 13, 2020 Appendix A: Technical Specifications LAN Ports Specifications and Pinouts Port Specifications The access point port specifications are shown in Table 7. Table 7. LAN Port Specifications Connector Specification Standards IEEE 802.3 (10Base-T) IEEE 802.3u (100Base-TX) IEEE 802.3ab (1000Base-T) IEEE 802.3bz (2.5Base-T IEEE 802.3bz (5Base-T) PoE standard IEEE 802.3at (class tbd) Port Pinouts The pin signal definitions for the Ethernet port are given here. Figure 36 illustrates the pin layout of the port. Figure 36. Pin Layout for RJ45 Connector on the Ethernet Port Table 8 lists the pin signals for ports operating at 10/100Mbps in the MDI configuration. Table 8. MDI Pin Signals at 10/100Mbps Pin Signal 1 2 3 6 TX+

TX-

RX+

RX-

74 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Table 9 lists the pin signals for ports operating at 10/100Mbps in the MDI-

X configuration. Table 9. MDI-X Pin Signals at 10/100Mbps Pin Signal 1 2 3 6 RX+

RX-

TX+

TX-

Table 10 lists the pin signals for LAN ports operating at 1/2.5/5Gbps. Table 10. Connector Pinouts at 1/2.5/5Gbps Pin Pair Signal 1 2 3 4 5 6 7 8 1 1 2 3 3 2 4 4 TX and RX TX and RX-

TX and RX+

TX and RX+

TX and RX-

TX and RX-

TX and RX+

TX and RX-

75 Review Draft - July 13, 2020 Appendix A: Technical Specifications 76 Review Draft - July 13, 2020 Appendix B Regulatory Statements This appendix contains the following regulatory statements:

Federal Communication Commission Interference Statement on page 78 Industry Canada Statement on page 80 Europe - EU Declaration of Conformity on page 82 77 Review Draft - July 13, 2020 Appendix B: Regulatory Statements Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Caution Avertissement de la FCC: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. E80 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range, it is restricted to indoor environment. The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. 78 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. 79 Review Draft - July 13, 2020 Appendix B: Regulatory Statements Industry Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-

exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lemetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

(1) Lappareil ne doit pas produire de brouillage.

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la Class B est conforme la norme NMB-003 du Canada. Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-

5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

(iii) the maximum antenna gain permitted for devices in the band 5725-

5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and

(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated.

(v) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-

5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. 80 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide Avertissement:

Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 5 350 MHz et de 5470 5725 MHz doit tre conforme la limite de la p.i.r.e;

(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;

(iv) les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, et nonce la section 6.2.2 3), doivent tre clairement indiqus.

(v) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--

d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. 81 Review Draft - July 13, 2020 Appendix B: Regulatory Statements Europe - EU Declaration of Conformity Operating Frequencies and Maximum Transmission Power Levels Hereby, Allied Telesis declares that the radio equipment type

[TQ6602] is in compliance with Directive 2014/53/EU. The operating frequencies and maximum transmission power levels for wireless devices operated in the EU are listed below:

- 2412-2472 MHz:

- 5150-5250 MHz:

- 5250-5350 MHz:

- 5470-5725 MHz:

19.23 dBm (Beamforming), 18.79dBm (Non-Beamforming) 22.11 dBm (Beamforming), 22.13dBm (Non-Beamforming) 22.06 dBm (Beamforming), 21.87dBm (Non-Beamforming) 28.97 dBm (Beamforming), 28.70dBm (Non-Beamforming) Note Operations in the 5.15 - 5.35 GHz band are restricted to indoor usage only. Radiation Exposure Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Importer Allied Telesis International BV Incheonweg 7, 1437 EK Rozenburg Note Contact Allied Telesis for the EU conformity statement. To contact Allied Telesis, visit our web site at www.alliedtelesis.com/contact. 82 Review Draft - July 13, 2020 Appendix C Radiation Patterns This appendix contains the following sections:

2.4GHz Antenna 1 on page 84 2.4GHz Antenna 2 on page 85 2.4GHz Antenna 3 on page 86 2.4GHz Antenna 4 on page 87 5GHz Antenna 1 on page 88 5GHz Antenna 2 on page 89 5GHz Antenna 3 on page 90 5GHz Antenna 4 on page 91 Z X Y Figure 37. Axes on the TQ6602 Access Point 83 Review Draft - July 13, 2020 Appendix C: Radiation Patterns 2.4GHz Antenna 1 TBD 84 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide 2.4GHz Antenna 2 TBD 85 Review Draft - July 13, 2020 Appendix C: Radiation Patterns 2.4GHz Antenna 3 TBD 86 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide 2.4GHz Antenna 4 TBD 87 Review Draft - July 13, 2020 Appendix C: Radiation Patterns 5GHz Antenna 1 TBD 88 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide 5GHz Antenna 2 TBD 89 Review Draft - July 13, 2020 Appendix C: Radiation Patterns 5GHz Antenna 3 TBD 90 Review Draft - July 13, 2020 TQ6602 Wireless Access Point Installation Guide 5GHz Antenna 4 TBD 91 Review Draft - July 13, 2020 Appendix C: Radiation Patterns 92 Review Draft - July 13, 2020

Revision Description Drawn / Date Checked / Date Section A ECO# CXXXXXX, Initial release. H.Ichijo Jul,21/20 I.Yagishita Jul,21/20 UD 140.69mm 21.0mm Model () () : AT-TQ6602 Power (\) : 12V, 4A(Adapter) ; 48V, 0.67A(PoE)

: 802.11ax

: (MADE IN TAIWAN (T))

alliedtelesis.com WARNING HOT SURFACE DO NOT TOUCH I.T.E. 4G17 E183341 IC:3336D-TQ6602 CAN ICES-3(B)/NMB-3(B) Importer:

Allied Telesis International BV Incheonweg 7, 1437 EK Rozenburg Netherlands Manufacturer:

Allied Telesis, Inc. 3041 Orchard Parkway San Jose, CA 95134 USA FCC ID:RSL-TQ6602 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 705-010761 Rev.A 1. MATERIAL: METALLIC SILVER POLYESTER 0.002[0.051] OR 0.001[0.025] THICK WITH PERMANENT ACRYLIC OVERLAMINATE: COMPUTER PRINTABLE POLYESTER KNEADED MATTE LAMINATION 0.002[0.051] OR ADHESIVE BACKED. 0.001[0.025] THICK. MUST COMPLY WITH EU ROHS DIRECTIVE. 2. ALL TEXTS AND GRAPHICS ARE BLACK. 3. MUST CONFORM TO UL MARKING & LABELING SYSTEM PGDQ2. 4. MUST CONFORM TO CSA ACCEPTED ADHESIVE TYPE NAME PLATE OR UL MARKING & LABELING SYSTEM PGDQ8. 5. ALL DIMENSIONS ARE IN MM. TITLE LBL,RTG,TW,MAIN,AT-TQ6602,LF SIZE DWG NO. SCALE DNS 705-010761 REV A SHEET 1 of 1

Revision Description Drawn / Date Checked / Date Section A ECO# C0XXXXX, Initial release. H.Ichijo Jul,21/20 I.Yagishita Jul,21/20 UD 19.4mm XXX-XXXXXX R T XXX-XXXXXXX D74355 RoHS CCXXxxYYyyyZzW No user serviceable components inside. Do not open. Use only power adapters listed in instruction. 5GHz W52/W53 705-010762 Rev.A EN 62368-1 xxxxxxxxxx 109.36mm 1. MATERIAL: METALLIC SILVER POLYESTER 0.002[0.051] OR 0.001[0.025] THICK WITH PERMANENT ACRYLIC OVERLAMINATE: COMPUTER PRINTABLE POLYESTER KNEADED MATTE LAMINATION 0.002[0.051] OR ADHESIVE BACKED. 0.001[0.025] THICK. MUST COMPLY WITH EU ROHS DIRECTIVE. 2. ALL TEXTS AND GRAPHICS ARE BLACK. 3. MUST CONFORM TO UL MARKING & LABELING SYSTEM PGDQ2. 4. MUST CONFORM TO CSA ACCEPTED ADHESIVE TYPE NAME PLATE OR UL MARKING & LABELING SYSTEM PGDQ8. 5. ALL DIMENSIONS ARE IN MM. TITLE LBL,RTG,TW,LEFT,AT-TQ6602,LF SIZE DWG NO. SCALE DNS 705-010762 REV A SHEET 1 of 1

Allied Telesis K.K. Date: 2021/05/20 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Requesting Class II permissive change To Whom It May Concern:

The purpose of this letter is to request a Class II Permissive change for FCC ID: RSL-TQ6602 This report is prepared for FCC Class II permissive change. RF module and its antenna are not any changed. The major change filed under this application is:

Change #1: Update U-NII Band 2a and U-NII Band 2c Original Grant Issue Date is on 2020/12/24 Best Regards _____________________ Shunji Taki/ Director Address: 2nd. TOC Bldg. 721-11 Nishi-Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Company Name: Allied Telesis K.K. Tel: +81-3-5436-8350

FCC, Request for non-disclosure Date: 10-Aug-09 RF_501, Issue 5 Page 1 of 1 Company Name: Allied Telesis K.K. Address: 2nd. TOC Bldg. 721-11 Nishi-Gotanda, Shinagawa-

ku, City: Tokyo, 141-0034 Country: Japan To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: RSL-TQ6602 Reference number: HHH Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materiais submitted in support of FCC certification application:

Bill(s) of Material EX Block Diagrams

[X] Operational Description [KX] Schematic Diagrams (1 Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission's policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):

J Internal Photos User's Manual C1 Test Set-up Photos External Photos Justification: oo. eseoveseneranessaveveeesessvateseeesseseueseetesaeeesneestecs cesuesasenaesseceusenssaesaseeaeesncreseeatesatsensess Planned Release Date STC: (notes 2, 3, 4, 5) Date: 2021/01/08 Name and signature of applicant: Shunji Taki > Ko wl e Notes:

4) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Declaration of Authorization We Name: Allied Telesis K.K. Address: 2nd. TOC Bldg. 721-11 Nishi-Gotanda, Shinagawa-ku, City: Tokyo, 141-0031 Country: Japan Declare that:

Name Representative of agent: Delia Feng Agent Company name: Cerpass Technology Corporation Address: No.10, Lane 2, Lianfu Street, Luzhu Dist., City: Taoyuan City 33848 Country: Taiwan, R.O.C. is authorized to apply for Certification of the following product(s):

Product description: 802.1 1ax 4x4+4x4 dual-radio 2.4G/5G wireless AP Type designation: AT-TQ6602 Trademark: Allied Telesis on our behalf. Date: January 12, 2021 City: Tokyo Name: Shunji Taki Function: Director Signature:

Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent. RF_160, Issue 02

AT-TQ6602 Antenna Test Report Page 1 of 44 1 Antenna Introduction Page 2 of 44 2.1 S11 test results 2.1.1 2G1 2.1.2 2G2 Page 3 of 44 2.1.3 2G3 2.1.4 2G4 Page 4 of 44 2.1.5 5G1 2.1.6 5G2 Page 5 of 44 2.1.7 5G3 2.1.8 5G4 Page 6 of 44 2.2 Isolation test results 2.2.1 2G1 & 2G2 2.2.2 2G1 & 2G3 Page 7 of 44 2.2.3 2G1 & 2G4 2.2.4 2G1 & 5G1 Page 8 of 44 2.2.5 2G1 & 5G2 2.2.6 2G1 & 5G3 Page 9 of 44 2.2.7 2G1 & 5G4 2.2.8 2G2 & 2G3 Page 10 of 44 2.2.9 2G2 & 2G4 2.2.10 2G2 & 5G1 Page 11 of 44 2.2.11 2G2 & 5G2 2.2.12 2G2 & 5G3 Page 12 of 44 2.2.13 2G2 & 5G4 2.2.14 2G3 & 2G4 Page 13 of 44 2.2.15 2G3 & 5G1 2.2.16 2G3 & 5G2 Page 14 of 44 2.2.17 2G3 & 5G3 2.2.18 2G3 & 5G4 Page 15 of 44 2.2.19 2G4 & 5G1 2.2.20 2G4 & 5G2 Page 16 of 44 2.2.21 2G4 & 5G3 2.2.22 2G4 & 5G4 Page 17 of 44 2.2.23 5G1 & 5G2 2.2.24 5G1 & 5G3 Page 18 of 44 2.2.25 5G1 & 5G4 2.2.26 5G2 & 5G3 Page 19 of 44 2.2.27 5G2 & 5G4 2.2.28 5G3 & 5G4 Page 20 of 44 3.Gain & Patterns test results 3.1 Lab information Lab nameSatimo Address No.326 Sec.2, Kung Tao 5 Road, HsinChu City, Taiwan Certificationnone (Satimo system certification: CTIA, 3GPP, Wi-Fi alliance and WiMAX Forum) Isolation level>100dB Size (LxWxH)5m x 5m x 5m Normal applicationsAntenna radiation pattern measurement, OTA performance testing. Frequency measurement range0.4 to 6 GHz EUT scanning methodconical cut method Measurement distance1.6m Measurement Antenna specification (for and polarization each)dual polarization Antenna for 0.4 to 6.0 GHz frequency range Equipment list Page 21 of 44 4.Gain & Patterns test results 4.1 Measurement setting Up(+Z) Front Left Down Right (+X) Back(+

AUT Z Y X Page 22 of 44 0 90 180 270 XY Right Back Left Front YZ Up Back Down Front XZ Up Right Down Left Total angle How many angle scan one point Total scan point 175 5 36 360 5 73 Page 23 of 44

. 4.2 2D patterns 4.2.1 2G1 Z X Z Y X-Z Plane (E-total) Y-Z Plane (E-total) Page 24 of 44 X Y X-Y Plane (E-total) Page 25 of 44 4.2.2 2G2 X-Z Plane (E-total) X Z Z Y Y-Z Plane (E-total) Page 26 of 44 X Y X-Y Plane (E-total) Page 27 of 44 4.2.3 2G3 X-Z Plane (E-total) Z X Z Y Y-Z Plane (E-total) Page 28 of 44 X Y X-Y Plane (E-total) Page 29 of 44 4.2.4 2G4 X-Z Plane (E-total) X Z Z Y Y-Z Plane (E-total) Page 30 of 44 X Y X-Y Plane (E-total) Page 31 of 44 4.2.5 5G1 X-Z Plane (E-total) X Z Z Y Y-Z Plane (E-total) Page 32 of 44 X Y X-Y Plane (E-total) Page 33 of 44 4.2.6 5G2 X-Z Plane (E-total) X Z Z Y Y-Z Plane (E-total) Page 34 of 44 X Y X-Y Plane (E-total) Page 35 of 44 X-Z Plane (E-total) 4.2.7 5G3 X Z Z Y Y-Z Plane (E-total) Page 36 of 44 X Y X-Y Plane (E-total) Page 37 of 44 4.2.8 5G4 X-Z Plane (E-total) X Z Z Y Y-Z Plane (E-total) Page 38 of 44 X Y X-Y Plane (E-total) Page 39 of 44 5.Summary 5.1 Return Loss Frequency 2400 MHz 2450 MHz 2500 MHz Frequency 5150 MHz 5350 MHz 5725 MHz 5850 MHz 2G1

(dB) 14 14 14 5G1

(dB) 14 22 13 15 2G2

(dB) 20 15 12 5G2

(dB) 14 31 14 21 2G3

(dB) 16 15 12 5G3

(dB) 33 13 15 21 2G4

(dB) 11 13 12 5G4

(dB) 20 29 16 15 Page 40 of 44 5.2 Isolation Frequency 2400 MHz 2450 MHz 2500 MHz 5150 MHz 5350 MHz 5725 MHz 5850 MHz Frequency 2400 MHz 2450 MHz 2500 MHz 5150 MHz 5350 MHz 5725 MHz 5850 MHz Frequency 2400 MHz 2450 MHz 2500 MHz 5150 MHz 5350 MHz 5725 MHz 5850 MHz 2G1

2G2

(dB) 30 25 22 31 27 26 25 2G1

5G4

(dB) 26 26 27 34 30 28 27 2G2

5G4

(dB) 39 37 35 27 28 25 25 2G1

5G1

(dB) 24 24 25 22 21 21 21 2G2

5G1

(dB) 26 25 25 25 25 23 22 2G3

5G2

(dB) 26 26 27 20 19 18 20 2G1

2G3

(dB) 25 24 23 48 38 35 33 2G2

2G3

(dB) 19 19 19 41 38 43 34 2G3

2G4

(dB) 20 21 21 33 33 41 41 2G1

2G4

(dB) 22 23 23 37 38 34 42 2G2

2G4

(dB) 37 26 28 42 37 33 32 2G3

5G1

(dB) 34 32 33 30 29 33 31 Page 41 of 44 2G1

5G2

(dB) 33 32 34 29 35 28 29 2G2

5G2

(dB) 30 31 30 31 26 26 23 2G3

5G3

(dB) 23 24 24 32 27 25 24 2G1

5G3

(dB) 33 33 32 40 37 37 35 2G2

5G3

(dB) 35 43 41 38 39 36 36 2G3

5G4

(dB) 31 32 37 37 31 33 32 Frequency 2400 MHz 2450 MHz 2500 MHz 5150 MHz 5350 MHz 5725 MHz 5850 MHz Frequency 2400 MHz 2450 MHz 2500 MHz 5150 MHz 5350 MHz 5725 MHz 5850 MHz 2G4

5G1

(dB) 35 35 33 33 30 28 29 5G1

5G4

(dB) 44 41 38 27 28 25 26 2G4

5G2

(dB) 38 34 35 38 31 29 29 5G2

5G3

(dB) 44 49 50 26 26 28 30 2G4

5G3

(dB) 26 27 26 65 36 35 35 5G2

5G4

(dB) 38 38 38 26 24 28 25 2G4

5G4

(dB) 26 25 23 28 29 29 31 5G3

5G4

(dB) 38 36 37 23 23 25 23 5G1

5G2

(dB) 44 46 46 23 21 24 23 5G1

5G3

(dB) 43 42 40 25 30 26 30 Page 42 of 44 5.3.3D total Peak Gain & Efficiency 2G1 2G2 Peak Gain Efficiency Peak Gain Efficiency 2G3 2G4 Peak Gain Efficiency Peak Gain Efficiency Frequency 2400 MHz 2450 MHz 2500 MHz Frequency 2400 MHz 2450 MHz 2500 MHz 5150 MHz 5200 MHz 5250 MHz 5300 MHz 5350 MHz 5470 MHz 5500 MHz 5725 MHz 5750 MHz 5850 MHz

(dBi) 3.54 3.14 3.24

(dBi) 3.67 3.62 3.43

(dBi) 4.26 4.77 4.68 4.28 4.36 4.40 4.35 4.63 4.78 4.67

(%) 64 61 63

(%) 62 62 65

(%) 62 65 64 61 67 62 63 62 61 62

(dBi) 3.27 3.41 3.20

(dBi) 3.45 3.40 3.35

(dBi) 4.20 4.64 4.21 4.35 4.40 4.73 4.74 4.64 4.63 4.25 Frequency Peak Gain Efficiency Peak Gain Efficiency 5G1 5G2

(%) 61 62 61

(%) 65 61 64

(%) 62 63 64 68 60 63 61 62 64 63 Page 43 of 44 Frequency Peak Gain Efficiency Peak Gain Efficiency 5G3 5G4 5150 MHz 5200 MHz 5250 MHz 5300 MHz 5350 MHz 5470 MHz 5500 MHz 5725 MHz 5750 MHz 5850 MHz

(dBi) 4.66 4.53 4.24 4.20 4.39 4.17 4.64 4.13 4.18 4.63

(%) 62 61 63 64 62 62 61 63 61 63

(dBi) 4.33 4.35 4.58 4.48 4.55 4.60 4.66 4.86 4.29 4.75

(%) 64 63 62 63 63 61 64 63 62 63 Page 44 of 44

DECLARATION OF CONFORMITY (DoC) Equipment: 802.11ax 4x4+4x4 dual-radio 2.4G/5G wireless AP Trademark(s): Allied Telesis Models): AT-TQ6602 Manufacturer: Allied Telesis K.K. FCC ID in case other parts of this RSL-TQ6602 equipment are subject to certification:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. The following test reports are subject to this declaration:

Test report number: Issue date:

TEFD2007311 Aug. 12, 2020 Company name: Allied Telesis K.K. Name/Title (legal representative): Shunji Taki/Director Address: 2nd. TOC Bldg. 721-11 Nishi-Gotanda, Shinagawa-ku, Tokyo Japan, 141-0031 Phone: +81-3-5436-8350 Fax: +81-3-5436-8351 E-mail: staki@allied-telesis.cojp Date: Nov. 25, 2020 Signature:

ie

FCC, Request for non-disclosure Date: 10-Aug-09 RF_501, Issue 5 Page 1 of 1 Company Name: Allied Telesis K.K. Address: and. TOC Bldg. 721-11 Nishi-Gotanda, Shinagawa-

ku, City: Tokyo, 141-0031 Country: Japan To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: RSL-TQ6602 Reference number: #444 Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material x] Block Diagrams KX] Operational Description ><} Schematic Diagrams LJ] Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission's policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):

Internal Photos [] User's Manual Test Set-up Photos External Photos JUSTIFICATION a eecccessteeneeceectesenseseeenenstesee sesssneesneneeessuseeenueeseseeesenenercnsterenseeseaes sesseneeeesaeesseaseceasen Planned Release Date STC: (notes 2, 3, 4, 5) Date: 2020/11/25 Name and signature of applicant: Shunji Taki Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)}!

3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period