FCC ID: RSL-TQ6602GEN2 IEEE802.11ax dual-radio 5G/2.4GHz 4x4+4x4 wireless AP

TQ6K GEN2 WIRELESS ACCESS POINTS AT-TQ6702 GEN2 AT-TQm6702 GEN2 802.11ax Dual-radio 5G/2.4GHz 8x8+4x4 Access Points AT-TQ6602 GEN2 AT-TQm6602 GEN2 802.11ax Dual-radio 5G/2.4GHz 4x4+4x4 Access Points Installation Guide 613-002972 Rev. A Draft 3 on June 9, 2021 Copyright 2021 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages. Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Electrical Safety and Emissions Standards This product meets the following standards:

Federal Communications Commission Interference Statement European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment on page 4 Safety and Electromagnetic Emissions on page 5 Translated Safety Statements on page 8 Federal Communications Commission Interference Statement Declaration of Conformity Manufacturer Name: Allied Telesis Declares that the product: 802.11ax dual-radio 2.4G/5G wireless access points Model Number: AT-TQ6702 GEN2, AT-TQm6702 GEN2, AT-TQ6602 GEN2, and AT-TQm6602 GEN2 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3 Draft 3 on June 9, 2021 Caution FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Avertissement Avertissement de la FCC: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. E80 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Allied Telesis ensures RoHS conformance by requiring supplier Declarations of Conformity, monitoring incoming materials, and maintaining manufacturing process controls. Note For additional regulatory statements, refer to Appendix B, Regulatory Statements on page 67. 4 Draft 3 on June 9, 2021 Safety and Electromagnetic Emissions TQ6K GEN2 Access Points Installation Guide European Union RoHS (Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.) Standard Compliance RoHs compliant Wire Communication IEEE 802.1 IEEE 802.3 IEEE 802.3u IEEE 802.3z IEEE 802.3ab IEEE 802.3bz IEEE 802.3x IEEE 802.3at ITU-T G.993.1 Wireless Communication IEEE 802.11 DSSS IEEE 802.11a OFDM IEEE 802.11b DSSS/FHSS IEEE 802.11g OFDM IEEE 802.11n OFDM IEEE 802.11ac OFDM IEEE 802.11ax OFDMA Safety CB/UL IEC 62368-1 UL 62368-1 CSA C22.2 No. 62368-1 IEC 60950-1 TUV EN62368-1 (Co-license) UL2043 5 Draft 3 on June 9, 2021 Electro Magnetic Interference (EMI) FCC part15 Subpart B/ Class B EN55032 Class B VCCI-CISPR 32 / Class B AS/NZS CISPR 32 Electro Magnetic Susceptibility - EN55024 and EN55035 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-8 IEC 61000-4-11 IEC 61000-3-2 IEC 61000-3-3 47 CFR Part15, subpart C 47 CFR Part15, subpart E FCC DFS CE RED Directive 2014/53/EU EN55032 EN55024 EN301489-1 V2.1.1 EN301489-17 V3.1.1 EN300328 V2.2.2 EN301893 V2.1.1 EN62311/ EN50385 European Council Directive 2014/30/EU DFS EN550.5 EN60601-1-2 6 Draft 3 on June 9, 2021 RCM IC AS/NZS CISPR 32 AS/NZS 4268 ICES-003 Issue 6 RSS-102 RSS-247 Issue 2 Japan JATE ARIB STD-T66 ARIB STD-T71 Hong Kong OFCA India WPC Malaysia SIRIM Singapore IMDA TS SRD Taiwan BSMI & NCC CNS 13438 CNS 14336-1

(LP002) Thailand NBTC Vietnam MIC China SRRC Complies with IMDA Standards DB102434 Figure 1. Singapore IMDA Logo TQ6K GEN2 Access Points Installation Guide 7 Draft 3 on June 9, 2021 Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements on the Allied Telesis website at www.alliedtelesis.com/library. Remarque: Les consignes de scurit portant le symbole sont traduites dans plusieurs langues dans le document Translated Safety Statements, disponible l'adresse www.alliedtelesis.com/

library. 8 Draft 3 on June 9, 2021 Contents Preface ............................................................................................................................................................15 Safety Symbols Used in this Document .................................................................................................... 16 Contacting Allied Telesis ........................................................................................................................... 17 Chapter 1: Product Description ................................................................................................................... 19 Features ..................................................................................................................................................... 20 TQ6K GEN2 Models .................................................................................................................................. 23 Hardware Components .............................................................................................................................. 25 Cable Hide........................................................................................................................................... 27 Console Port........................................................................................................................................ 27 Power Switch....................................................................................................................................... 27 Kensington Lock Hole.......................................................................................................................... 27 Reset Button ........................................................................................................................................ 27 LAN1 and LAN2 Ports................................................................................................................................ 28 Static Link Aggregation........................................................................................................................ 28 Cascade Mode .................................................................................................................................... 29 Power Over Ethernet Plus (PoE+)....................................................................................................... 30 Connector Type ................................................................................................................................... 30 Speed .................................................................................................................................................. 30 Duplex Mode ....................................................................................................................................... 30 Automatic MDIX Detection .................................................................................................................. 30 Cable Requirements............................................................................................................................ 31 Maximum Distance .............................................................................................................................. 31 Port Pinouts ......................................................................................................................................... 31 Guidelines............................................................................................................................................ 31 AC Adapter for External Power Supply ...................................................................................................... 32 LEDs .......................................................................................................................................................... 33 Chapter 2: Installing the Wireless Access Point ........................................................................................35 Reviewing Safety Precautions ................................................................................................................... 36 Unpacking the Shipping Box ...................................................................................................................... 39 Reviewing Installation Guidelines .............................................................................................................. 40 Installing the Access Point on a Table ....................................................................................................... 42 Overview to Installing the Access Point on a Wall or Ceiling ..................................................................... 43 Pre-fitting the Mounting Bracket on the Access Point ................................................................................ 44 Installing the Mounting Bracket on a Wall or Ceiling.................................................................................. 47 Connecting Ethernet Cables to LAN1 and LAN2 Ports.............................................................................. 51 Guidelines............................................................................................................................................ 51 Connecting the Ethernet Cables to LAN Ports .................................................................................... 51 Connecting the AC Power Adapter ............................................................................................................ 54 Attaching the Access Point to the Mounting Bracket ................................................................................. 55 Installing an Anti-theft Device..................................................................................................................... 58 Starting the First Management Session ..................................................................................................... 59 Appendix A: Technical Specifications ........................................................................................................61 Physical Specifications............................................................................................................................... 61 Environmental Specifications ..................................................................................................................... 61 Power Specifications.................................................................................................................................. 62 9 Draft 3 on June 9, 2021 Contents Input Power Specifications...................................................................................................................62 External AC Adapter Specifications .....................................................................................................62 PoE+ Power Requirements.................................................................................................................. 63 Cable Specifications ...................................................................................................................................64 LAN Ports Specifications and Pinouts ........................................................................................................65 Port Specifications ...............................................................................................................................65 Port Pinouts..........................................................................................................................................65 Appendix B: Regulatory Statements ........................................................................................................... 67 Federal Communication Commission Interference Statement ...................................................................68 Industry Canada Statement........................................................................................................................70 Europe - EU Declaration of Conformity ...................................................................................................... 72 Operating Frequencies and Maximum Transmission Power Levels ....................................................72 Radiation Exposure Statement ............................................................................................................72 Importer................................................................................................................................................72 UK - UKCA Declaration of Conformity........................................................................................................73 Operating Frequencies and Maximum Transmission Power Levels ....................................................73 Radiation Exposure Statement ............................................................................................................73 Importer................................................................................................................................................73 10 Draft 3 on June 9, 2021 Figures Figure 1: Singapore IMDA Logo ........................................................................................................................ 7 Figure 2: TQ6K GEN2 Access Point Top View ............................................................................................... 25 Figure 3: Access Point Bottom View ............................................................................................................... 25 Figure 4: Front Edge View ............................................................................................................................... 26 Figure 5: Back Edge View ............................................................................................................................... 26 Figure 6: Left Edge View ................................................................................................................................. 26 Figure 7: LAN1 and LAN2 Ports in a Static LAG ............................................................................................. 28 Figure 8: LAN2 Port in Cascade Mode with an End Node .............................................................................. 29 Figure 9: LAN2 Port in Cascade Mode with a Networking Device .................................................................. 29 Figure 10: AT-PWRADP-01 Power Adapter.................................................................................................... 32 Figure 11: TQ6K GEN2 Access Point Top View ............................................................................................. 33 Figure 12: Shipping Box Components............................................................................................................. 39 Figure 13: Approved Installation Orientations on a Ceiling, Wall, or Table ..................................................... 41 Figure 14: Attaching the Bracket Screws to the Wireless Access Point .......................................................... 44 Figure 15: Attaching the Mounting Bracket on the Access Point..................................................................... 45 Figure 16: Adjusting the Screws on the Access Point ..................................................................................... 45 Figure 17: Removing the Mounting Bracket from the Access Point ................................................................ 46 Figure 18: Marking the Holes for the Key-Hole Slots ...................................................................................... 47 Figure 19: Installing Two Screws..................................................................................................................... 48 Figure 20: Installing the Mount Bracket On the Screws .................................................................................. 49 Figure 21: Pre-Drill Holes on Mounting Bracket .............................................................................................. 49 Figure 22: Securing the Mount Bracket ........................................................................................................... 50 Figure 23: Connecting an Ethernet Cable to the LAN1 Port............................................................................ 51 Figure 24: Removing the Dust Plug from the LAN2 Port ................................................................................. 52 Figure 25: Connecting the Ethernet Cable to the LAN2 Port........................................................................... 52 Figure 26: Connecting an AC Power Adapter to the Access Point.................................................................. 54 Figure 27: Installing the Access Point on the Mounting Bracket ..................................................................... 55 Figure 28: Seating the Access Point on the Mounting Bracket ....................................................................... 56 Figure 29: Tightening the Mounting Bracket Thumbscrew .............................................................................. 56 Figure 30: Fitting the Cables in the Cable Hide............................................................................................... 57 Figure 31: Kensington Lock Port Location....................................................................................................... 58 Figure 32: Login Prompt .................................................................................................................................. 59 Figure 33: Pin Layout for RJ45 Connector on LAN Port.................................................................................. 65 11 Draft 3 on June 9, 2021 List of Figures 12 Draft 3 on June 9, 2021 Tables Table 1. Product Limitations ........................................................................................................................... 22 Table 2. Differences Between the TQ6K GEN2 Access Points ...................................................................... 23 Table 3. LED Status Information .................................................................................................................... 33 Table 4. Physical Specifications ..................................................................................................................... 61 Table 5. Environmental Specifications ........................................................................................................... 61 Table 6. Input Power Specifications ............................................................................................................... 62 Table 7. External AC/DC Adapter Specifications ........................................................................................... 62 Table 8. PoE+ Power Requirements on LAN Ports ........................................................................................ 63 Table 9. LAN Port Specifications .................................................................................................................... 65 Table 10. Pin Signals for 100M/1G/2.5G/5G Base-T Connectors .................................................................. 65 13 Draft 3 on June 9, 2021 List of Tables 14 Draft 3 on June 9, 2021 Preface This guide contains the hardware installation instructions for the TQ6K GEN2 Access Points. The access point models included in this manual are:

AT-TQ6702 GEN2 AT-TQm6702 GEN2 AT-TQ6602 GEN2 AT-TQm6602 GEN2 This preface contains the following sections:

Safety Symbols Used in this Document on page 16 Contacting Allied Telesis on page 17 15 Draft 3 on June 9, 2021 Preface Safety Symbols Used in this Document This document uses the following conventions. Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a specific action may result in bodily injury. Warning Warnings inform you of hot surfaces. 16 Draft 3 on June 9, 2021 Contacting Allied Telesis TQ6K GEN2 Access Points Installation Guide If you need assistance with this product, you may contact Allied Telesis technical support by going to the Services & Support section of the Allied Telesis web site at www.alliedtelesis.com/support. You can find links for the following resources on this page:

Helpdesk (Support Portal) - Log onto Allied Telesis interactive support center to search for answers to your questions in our knowledge database, check support tickets, learn about Return Merchandise Authorizations (RMAs), and contact Allied Telesis technical experts. Software Downloads - Download the latest software releases for Licensing - Register and obtain your License key to activate your your product. product. Product Documents - View the most recent installation guides, user guides, software release notes, white papers and data sheets for your product. Warranty - View a list of products to see if Allied Telesis warranty applies to the product you purchased and register your warranty. Allied Telesis Helpdesk - Contact a support representative. For sales or corporate contact information, go to www.alliedtelesis.com/contact and select your region. 17 Draft 3 on June 9, 2021 Preface 18 Draft 3 on June 9, 2021 Chapter 1 Product Description The sections in this chapter describe the hardware components of the TQ6K GEN2 Wireless Access Points:

Features on page 20 TQ6K GEN2 Models on page 23 Hardware Components on page 25 LAN1 and LAN2 Ports on page 28 AC Adapter for External Power Supply on page 32 LEDs on page 33 19 Draft 3 on June 9, 2021 Chapter 1: Product Description Features 20 Hardware features include:

One 2.4GHz radio One 5GHz radio Internal omni-directional antennas Two 100/1000Mbps/2.5G/5G Ethernet ports with RJ-45 connectors PoE+ Class 4 powered device One Reset button for restoring the default settings One AC power adapter connector LEDs for 2.4GHz and 5GHz radios, LAN1 and LAN2 ports, and power Kensington lock port Ceiling, wall, or table installation Installing on the Cisco or Fortimet mounting brackets using AT-BRKT-CONV-AP1 converter bracket One Console RS232 RJ-45 port for factory use only Features of the 2.4GHz and 5GHz radios include:

IEEE802.11a/b/g/n/ac/ax Automatic channel selection Band steering Wi-Fi multimedia (WMM) for prioritizing traffic Features of Power and Power over Ethernet (PoE):

PoE+ (IEEE 802.3at) Maximum power consumption: less than 25.5W Power saving mode: support IEEE802.3af when either 2.5G or 5G is disabled. Redundant power by AC adapter and PoE+ ports Software features include:

Zero Wait DFS Flow control (IEEE 802.3x) VLAN tagging (IEEE 802.1Q) Link aggregation Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Cascade configuration On-board web browser management interface Virtual access point (VAP) Network Time Protocol (NTP) client Dynamic Host Control Protocol (DHCP) client Static WEP, WPA Personal, and WPA Enterprise security Static WEP encryption: 64/128 bit (IEEE802.11a/b/g) WPA and WPA2 encryption: CCMP (AES) and TKIP WPA3 encryption CCMP (AES/CNSA) Quality of Service (QoS) ingress and egress queues Fast roaming (IEEE802.11v/k/r) Captive portals MAC address client filtering with the on-board filter MAC address client filtering with RADIUS servers Wireless Distribution System (WDS) bridges Quick Response codes for VAPs System log Syslog client SNMPv1, v2c, and v3 Link Aggregation Orthogonal Frequency Division Multiple Access (OFDMA) Software features with Vista Manager EX and the Autonomous Wave Controller (AWC) plug-in include:

AWC-Channel Blanket (AWC-CB) on AT-TQ6602 GEN2 and AWC-Smart Connect (AWC-SC) on AT-TQ6602 GEN2 and Terminator AP support on AT-TQm6602 GEN2 and AT-TQm6702 AT-TQ6702 GEN2 AT-TQ6702 GEN2 GEN2 AWC Lite Combination use with Cell, AWC-SC, and AMF-SEC Autonomous Management Framework (AMF) Guest node 21 Draft 3 on June 9, 2021 Chapter 1: Product Description Table 1 indicates limitations:

Table 1. Product Limitations Feature Item VAP Virtual wireless interfaces per RF interface WDS WDS links ESSID VLAN ID WDS HOPs AWC Access points managed by AWC 3,000 Client Authentication MAC address list 4,096 Maximum Number 16 32 4 2 4,094 22 Draft 3 on June 9, 2021 TQ6K GEN2 Models TQ6K GEN2 Access Points Installation Guide The Table 2 lists the basic differences among four models.. Table 2. Differences Between the TQ6K GEN2 Access Points Model AT-TQ6602 GEN2 AT-TQ6702 GEN2 AT-TQm6602 GEN2 AT-TQm6702 GEN2 Maximum number of access points managed by AWC More than 100 Less than 100 Maximum number of wireless client 200 clients per radio in standalone mode 127 clients per radio in standalone mode 500 clients per Channel Blanket MIMO 2.4GHz: 4x4 2.4GHz: 4x4 2.4GHz: 4x4 2.4GHz: 4x4 5GHz: 4x4 5GHz: 8x8 5GHz: 4x4 5GHz: 8x8 AWC-CB 2,000 Access points per Channel Blanket VAP Blankets per access point 32 16 blankets per radio Communicating clients at one time per Channel Blanket Client sessions at one time per Channel Blanket 2,000 10,000 Links per access point Hops per access point 4 8 Access points per mesh group 21,844 AWC-SC Link rate (2.4GHz) Link rate (5GHz) 1,147Mbps (4x4) 2,402Mbps

(4x4) 4,804Mbps

(8x8) 2,402Mbps

(4/4) 4,804Mbps

(8x8) AWC-CB is not supported Supported terminator access points only 23 Draft 3 on June 9, 2021 Chapter 1: Product Description Note The Channel Blankets feature, also referred to as single-channel mode, allows neighboring wireless access points to use the same channels to more efficiently handle roaming wireless clients. The feature requires Vista Manager EX and the Autonomous Wireless Controller (AWC) plug-in. 24 Draft 3 on June 9, 2021 Hardware Components TQ6K GEN2 Access Points Installation Guide The top view of the TQ6K GEN2 Access Point is illustrated in Figure 1. Back Edge Figure 1. TQ6K GEN2 Access Point Top View The bottom view is illustrated in Figure 2. Front Edge Back Edge Cable Hide 25 Front Edge Figure 2. Access Point Bottom View Draft 3 on June 9, 2021 Chapter 1: Product Description The front edge view is illustrated in Figure 3. Mounting Bracket Thumb Screw Hole Figure 3. Front Edge View The back edge view is illustrated in Figure 4. Console Port DC IN Connector for AC/DC Adapter LAN1 POE+ Port Power Switch LAN2 POE+ Port Reset Button Figure 4. Back Edge View The left edge view is illustrated in Figure 5. Kensington Lock 26 Figure 5. Left Edge View Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Cable Hide The top cover of the access point is larger than the access point chassis to create space on the back for cable connectors and cables shown in Figure 2 on page 25. Console Port The Console Serial port on the back panel is for manufacturing purposes only. Power Switch The Power Switch on the back panel in Figure 4 on page 26 turns On or OFF the access point when power is supplied to the access point only from the AC adapter, not from PoE LAN ports. When power is supplied to the access point from the PoE LAN ports, the state of the Power Switch does not affect the access point. Kensington Lock Hole The left panel has a hole for the Kensington lock to be connected to an anti-theft cable/lock to physically secure the access point as shown in Figure 5 on page 26. Reset Button The access point has a Reset button on the back edge in Figure 4 on page 26 for returning the parameter settings of the device to their default values. You might reset the access point if you want to discard its current configuration or if you forgot the manager password and so cannot manage the device. To reset the device, press the button for five seconds and release. You can enable or disable the reset button with the management software. The default setting for the button is enabled. If the access point is installed in a public area, you probably should disable it to protect the device from being reset by unauthorized individuals. 27 Draft 3 on June 9, 2021 Chapter 1: Product Description LAN1 and LAN2 Ports The wireless access point has two Ethernet ports, labeled LAN1 and LAN2. You use the ports to connect the wireless access point to your wired network. Here are their basic properties:

LAN1 and LAN2 ports support PoE+. The default setting for LAN1 port is enabled. You cannot disable it. The default setting for LAN2 port is disabled. LAN1 and LAN2 ports can be combined into a static Link Aggregation (LAG) to double the bandwidth between the wireless access point and the wired network. LAN2 can be configured as a separate Ethernet port for another network device. This is referred to as the Cascade mode. Static Link Aggregation You can double the bandwidth between the wireless access point and your wired network by combining LAN1 and LAN2 ports into a static LAG. A static LAG functions as a single logical link between the wireless access point and another network device, such as an Ethernet switch or router. A static LAG also provides link redundancy. If one link goes down, the wireless access point maintains connectivity to the wired network over the remaining link. Refer to Figure 6. Figure 6. LAN1 and LAN2 Ports in a Static LAG Here are guidelines to using LAN1 and LAN2 ports as a static LAG:

You have to connect the ports to the same network device, such as an Ethernet switch or router, or virtual stacking devices. Do not connect the LAN ports to different network devices. The network device has to support static LAGs. You have to configure the two ports on the network device as a static LAG. You activate the static LAG for LAN1 and LAN2 ports with the on-board web browser management interface. 28 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Note Do not enable and cable the LAN2 port until after you have configured the other network device for the static LAG. Cascade Mode The LAN2 port also has a Cascade mode. The mode allows you to use the port to connect another device to your network. The device can be an end node such as a printer or computer, as shown in Figure 7. To Network Core LAN2 Port Figure 7. LAN2 Port in Cascade Mode with an End Node It can also be a networking device such as a switch, router, or media converter. Refer to Figure 8. To Network Core Figure 8. LAN2 Port in Cascade Mode with a Networking Device Here are the Cascade mode guidelines:

The Cascade mode requires firmware version 6.0.1-2.1 or later. You set the Cascade mode with the on-board web browser The Cascade mode is not supported with Vista Manager EX and management interface. the AWC plug-in. Do not connect both LAN1 and LAN2 ports to the same network device when the LAN2 port is in the Cascade mode. 29 Draft 3 on June 9, 2021 Chapter 1: Product Description Power Over Ethernet Plus

(PoE+) You can power the wireless access point with either PoE+ on the LAN1 port, LAN2 port or an AC/DC power adapter. The wireless access point is a PoE+ Class 4 powered devices, with maximum power consumption of 25.5 watts. To power the device with PoE+, you have to connect LAN1 or LAN2 port to a PoE+ source device. The network cable connecting the LAN1 or LAN2 port to the PoE+ source device carries both network traffic and PoE+. You can power the device with both PoE+ and an AC/DC power adapter. However, the two power sources are not load sharing. The power adapter is the primary power source and PoE+ is redundant power. Connector Type The LAN ports have an eight-pin RJ45 connector. The port uses four pins of the connector at 100 Mbps and all eight pins at 1G/2.5G/5Gbps. Refer to the tables in Port Pinouts on page 65 for the pin assignments. Speed The LAN ports have speeds of 100Mbps/1G/2.5G/5Gbps. The speeds are set automatically with Auto-Negotiation. You cannot disable Auto-Negotiation on the ports. Note The LAN ports should be connected to network devices that also adjust port speeds with Auto-Negotiation. If a network device does not support Auto-Negotiation, the LAN ports operate at 100 Mbps, which may reduce network performance. Duplex Mode Both LAN ports can operate in either half- or full-duplex mode at 100Mbps, and full-duplex mode at 1G/2.5G/5Gbps. The ports are IEEE802.3u compliant and use Auto-Negotiation to set the duplex mode. You cannot disable Auto-Negotiation on the port. Note The network device to which you connect the LAN ports should also set the duplex mode with Auto-Negotiation. If a network device does not support Auto-Negotiation, the LAN port operates at half-duplex mode. This may result in a duplex mode mismatch if the network device is operating at full duplex. Automatic MDIX Detection When operating at 100Mbps, the twisted-pair ports feature automatic MDIX detection. (Automatic MDIX detection does not apply to 1G/2.5G/

5Gbps.) This feature automatically configures the ports to MDI or MDI-X depending on the wiring configuration of the port on the Ethernet switch. 30 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide You cannot disable automatic MDIX detection. For automatic MDIX detection to work properly, this feature must also be present on the Ethernet switch. The LAN port defaults to MDIX if it is connected to a network device that does not support automatic MDIX detection. The minimum cable requirements for the ports are listed here. 10Mbps or100 Mbps port: Standard TIA/EIA 568-B-compliant Category 3 shielded or unshielded cabling. 1/2.5/5Gbps port: Standard TIA/EIA 568-A-compliant Category 5 or TIA/EIA 568-B-compliant Enhanced Category 5 (Cat 5e) unshielded cabling. Cable Requirements Maximum Distance The LAN ports have a maximum operating distance of 100 meters (328 feet). Port Pinouts See Table 10 on page 65 for port pinouts information. Guidelines Here are the guidelines to using the LAN1 and LAN2 ports:

If you are connecting only one LAN port to your network, you have The default setting for the LAN1 port is enabled. You cannot to use port LAN1. disable it. The default setting for LAN2 is disabled. To activate it, use the on-board web browser management interface. To use the LAN1 and LAN2 ports as a static LAG, you have to connect them to the same network device, such as an Ethernet switch or router, or virtual stacking devices. Do not connect the LAN ports to different network devices. The network device has to support static LAGs. Caution When using LAN1 and LAN2 ports as a static LAG, do not activate the LAN2 port until you have configured the ports on the network device to which the LAN ports are connected as a static LAG. Refer to the documentation for the network device for instructions. To activate the Cascade mode for LAN2, use the on-board web browser management interface. 31 Draft 3 on June 9, 2021 Chapter 1: Product Description AC Adapter for External Power Supply The access point can be powered in two ways:

PoE+ Sourcing Equipment (PSE) on LAN1 and/or LAN2 ports AC power adapter You can also power it with both methods for power redundancy. The power sources are not load-sharing. A wireless access point that has both power sources uses the AC power adapter as its primary power source and PoE+ as redundant power. For technical specifications, refer to Power Specifications on page 62. The AT-PWRADP-01 Power Adapter, shown in Figure 9, from Allied Telesis is approved for this product. Figure 9. AT-PWRADP-01 Power Adapter 32 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide LEDs The LEDs on the top panel display status information. See Figure 10 for LEDs and Table 3 for the status definition. Figure 10. TQ6K GEN2 Access Point Top View Table 3. LED Status Information LED State Description Green The access point is powered ON and operating normally. Blinking Green The access point is booting up. PWR/

SYS Red The access point has encountered a fault condition. Blinking Red The access point is upgrading its firmware. LAN1 Blinking Green The port is transmitting or receiving data. LAN2 Blinking Green The port is transmitting and receiving data. Off Green Off Green Off Green Off Off Green 2.4GHz 5 GHz The access point is not receiving power. The port has established a link to a network device. The port has not established a link to a network device. The port has established a link to a network device. The port has not established a link to a network device. The 2.4GHz radio is enabled. The 2.4GHz radio is disabled. The 5GHz radio is enabled. The 5GHz radio is disabled. 33 Draft 3 on June 9, 2021 Chapter 1: Product Description 34 Draft 3 on June 9, 2021 Chapter 2 Installing the Wireless Access Point This chapter contains the installation procedures for the TQ6K GEN2 Access Points. The procedures are detailed in the following sections:

Reviewing Safety Precautions on page 36 Unpacking the Shipping Box on page 39 Reviewing Installation Guidelines on page 40 Installing the Access Point on a Table on page 42 Overview to Installing the Access Point on a Wall or Ceiling on page 43 Pre-fitting the Mounting Bracket on the Access Point on page 44 Installing the Mounting Bracket on a Wall or Ceiling on page 47 Connecting Ethernet Cables to LAN1 and LAN2 Ports on page 51 Connecting the AC Power Adapter on page 54 Attaching the Access Point to the Mounting Bracket on page 55 Installing an Anti-theft Device on page 58 Starting the First Management Session on page 59 Note The non-US models of this product have a country code setting that must be set during the initial management session of the units. The setting ensures that the units operate in compliance with the laws and regulations of your country or region. For the US model, the country code is preset and cannot be changed. Per FCC regulations, the country code setting for all WiFi products marketed in the US must be fixed to US operational channels only. 35 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point Reviewing Safety Precautions Please review the following safety precautions before installing the access point. Important: Safety statements that have the symbol are translated into multiple languages in the Translated Safety Statements document, which is available at www.alliedtelesis.com/library. Warning To prevent electric shock, do not remove the cover. No user-serviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician. To avoid the possibility of electric shock, disconnect electric power to the product before connecting or disconnecting the LAN cables. E1 Warning Do not work on equipment or cables during periods of lightning activity. E2 Warning All Countries: Install product in accordance with local and National Electrical Codes. E8 Warning Only trained and qualified personnel are allowed to install or to replace this equipment. E14 Warning To reduce the risk of electric shock, the PoE ports on this product must not connect to cabling that is routed outside the building where this device is located. E40 Warning This equipment shall be installed in a Restricted Access location. E45 36 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Warning FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Note The access point must be powered by:

1. A UL listed external AC/DC power supply suitable for use at Tma 45 oC, a maximum operating altitude of 3000 m or higher, and whose output meets separated extra-low voltage (SELV), limited power sources (LPSs) and is rated 12 VDC, 2.0 A, OR 2. By Power over Ethernet through a UL listed ITE. Refer to Table 7, External AC/DC Adapter Specifications on page 62. Caution Air vents must not be blocked and must have free access to the room ambient air for cooling. E6 Warning An operational unit can be hot. Exercise caution when handling with unprotected hands. Warning Operating Temperature. This product is designed for a maximum ambient temperature of 45C (122 F) E7. Warning To reduce the risk of electric shock, the PoE port on this product must not connect to cabling that is routed outside the building where this device is located. E40 Warning This equipment is intended for indoor use only. E95 37 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point Note If you are not using PoE to power to unit, use only an approved AC/

DC adapter. Refer to Power Specifications on page 62. Caution The unit does not contain serviceable components. Please return damaged units for servicing. E42 Note You should verify that your PoE network adheres to the standards of a separated extra-low voltage (SELV) circuit before using the PoE feature on the wireless access point. 38 Draft 3 on June 9, 2021 Unpacking the Shipping Box TQ6K GEN2 Access Points Installation Guide To verify the contents of the shipping box, perform the following procedure:

1. Remove all components from the shipping box. Note Store the packaging material in a safe location. Please use the original shipping material if you need to return the device to Allied Telesis. 2. Verify the contents of the shipping box listed in Table 11. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. Figure 11. Shipping Box Components Name Component TQ6K GEN2 Access Point One Mounting Bracket Two M5 x 8mm, Pan-head Screws 39 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point Reviewing Installation Guidelines Review the following guidelines before installing the access point:

The ceiling or wall mounting surface must be of proper material to accommodate the screws and strong enough to support the weight of the access point and cables. (Refer to Table 4 on page 61 for the product weight.) You can install the access point on a wall where Cisco or Fortinet bracket has already been installed. You need a bracket converter. See the AT-BRKT-CONV-AP1 Bracket Converter Installation Guide for more information. Connect the Ethernet cable(s) and power cord (if applicable) to the access point before installing the product on the ceiling or wall. Depending on the installation location, connecting or removing cables may be difficult after the device is installed. Verify that the Ethernet cable(s) is long enough to connect to its destination port(s) before installing the access point. Once the installation is complete, it is physically difficult to change the cables. If the wireless access point is powered by an AC adapter, verify that an AC power outlet is within six feet of the planned installation site. (Refer to Power Specifications on page 62 for the AC adapter specifications.) Refer to Figure 12 on page 41 for approved orientations of the wireless access point on a table, wall, or ceiling. 40 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Ceiling Installation Wall Installation Table Installation Figure 12. Approved Installation Orientations on a Ceiling, Wall, or Table 41 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point Installing the Access Point on a Table You need the following items to install the access point on a table:

TQ6K GEN2 Access Point One or two Ethernet cables External AC power adapter (Optional if using PoE+. Required if not using PoE+ or for redundant power.) Kensington lock (optional) Note See Reviewing Safety Precautions on page 36 and Reviewing Installation Guidelines on page 40 before installing the product. Perform the following steps to install the wireless access point on a table:

1. Place the access point at the selected location on the table. 2. Connect Ethernet cables to LAN1 and LAN2 ports. Refer to Connecting Ethernet Cables to LAN1 and LAN2 Ports on page 51. 3. To connect an AC power adapter to the access point, go to Connecting the AC Power Adapter on page 54. 4. To install a security cable, refer to Installing an Anti-theft Device on page 58. Session on page 59. 5. To start managing the device, go to Starting the First Management 42 Draft 3 on June 9, 2021 Overview to Installing the Access Point on a Wall or Ceiling TQ6K GEN2 Access Points Installation Guide Here are the procedures for installing the wireless access point on a wall or ceiling:

Pre-fitting the Mounting Bracket on the Access Point on page 44 Installing the Mounting Bracket on a Wall or Ceiling on page 47 Connecting Ethernet Cables to LAN1 and LAN2 Ports on page 51 Connecting the AC Power Adapter on page 54 Attaching the Access Point to the Mounting Bracket on page 55 Installing an Anti-theft Device on page 58 Note Please see Reviewing Safety Precautions on page 36 and Reviewing Installation Guidelines on page 40 before installing the product. Note Depending on the installation location, it may be easier to connect the network cables and optional power adapter to the wireless access point before installing it on the wall or ceiling. You need the following items to install the wireless access point on a ceiling or wall:

TQ6K GEN2 Access Point Two screws to attach the access point to the mounting bracket Mounting bracket Four (4) M4, 25.0 mm flat-head wood screws and anchors (not provided) for fastening the mounting bracket Phillips head screwdriver (not provided) Pencil (not provided) External AC power adapter (Optional if using PoE+. Required if not using PoE+ or for redundant power.) Kensington lock (optional and not provided) Note The four Phillips head M4 screws/anchors, the Phillips head screwdriver, pencil, external AC power adapter and Kensington lock are not included with the product. 43 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point Pre-fitting the Mounting Bracket on the Access Point To pre-fit the mounting bracket on the access point, perform the following procedure:

1. Install the two screws (provided) in the bottom side of the access point chassis. Leave the screws loose enough so that you can slide the bracket under the screw heads. Refer to Figure 13. Figure 13. Attaching the Bracket Screws to the Wireless Access Point 2. Install the mounting bracket on the access point by sliding the keyholes under the screws. Refer to Figure 14 on page 45. 44 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Figure 14. Attaching the Mounting Bracket on the Access Point 3. Tighten the screws so that they touch the mounting bracket plate, and then loosen them by approximately 1/4 turn. Refer to Figure 15. Note Adjust the screws so they are loose enough for you to remove the bracket, but tight enough to prevent the access point from rattling against the mounting bracket. Figure 15. Adjusting the Screws on the Access Point 45 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point 4. Slide the mounting bracket forward and temporarily remove it from the access point. Refer to Figure 16. Figure 16. Removing the Mounting Bracket from the Access Point 5. Go to Installing the Mounting Bracket on a Wall or Ceiling on page 47. 46 Draft 3 on June 9, 2021 Installing the Mounting Bracket on a Wall or Ceiling TQ6K GEN2 Access Points Installation Guide To install the mounting bracket on a wall of ceiling, perform the following procedure:

1. Choose the location and orientation for the access point on the wall or ceiling. Refer to Figure 12 on page 41. 2. Position the mounting bracket at the selected location and orientation for the access point. Consider the following guidelines. The thumbscrew on the mounting bracket is where the front panel of the access point will be. The ports and connectors are on the back panel, away from the thumbscrew. 3. With a pencil, mark the wall or ceiling with the two key-hole slots of the bracket. Refer to Figure 17. Figure 17. Marking the Holes for the Key-Hole Slots 4. Pre-drill the two marked locations for the keyhole slots on the hard-surface ceiling or wall. 47 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point 5. Install two M4 screws and anchors (if required). Leave the screws loose enough so that the bracket can slide under the screw heads. Refer to Figure 18. Note For a wooden wall or ceiling, use M4 x 25 mm flat-head wood screws and anchors, if required. The screws and anchors are not provided. Figure 18. Installing Two Screws 48 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide 6. Insert the openings of the bracket key-hole slots under the two screw heads and slide the bracket into the narrow end of the key-hole slot openings. See Figure 19. Figure 19. Installing the Mount Bracket On the Screws 7. Tighten the screws snugly onto the bracket. 8. To secure the mounting bracket, pre-drill holes through the two bracket mounting holes opposite the key-hole slots. See Figure 20. Figure 20. Pre-Drill Holes on Mounting Bracket 49 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point 9. Install and tighten two M4 screws (not provided) in the holes prepared in Step 8. The bracket installation is now complete.See Figure 21. Figure 21. Securing the Mount Bracket 10. Go to Connecting Ethernet Cables to LAN1 and LAN2 Ports on page 51. 50 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Connecting Ethernet Cables to LAN1 and LAN2 Ports This section describes the instructions for connecting Ethernet cables to the LAN1 and LAN2 ports. Guidelines Review the following guidelines before connecting cables to the LAN1 and LAN2 ports:

For information on cable specifications, see Cable Requirements on page 31. If you are installing the access point on a ceiling or wall, you might find it easier to connect the cables before placing the unit on the mounting bracket. You must use port LAN1 if you are connecting only one LAN port to the network. To power the access point through PoE+ LAN port(s), see PoE+

Power Requirements on page 63. To use both LAN1 and LAN2 ports, you have to connect them to the same network device. The device must support static LAGs. The default setting for the LAN2 port and static LAG on the wireless access point is disabled. You enable them with the on-board web browser management interface. For instructions, see the TQ6K GEN2 Management Software Users Guide. Note Do not enable the LAN2 port until you have configured the other network device for the static LAG. Connecting the Ethernet Cables to LAN Ports To connect the network cables, perform the following procedure:

1. To cable LAN1 port, connect an Ethernet cable into the port. The cable requirements are in Cable Requirements on page 31. Refer to Figure 22. Figure 22. Connecting an Ethernet Cable to the LAN1 Port 51 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point 2. Connect the other end of the Ethernet cable to a network Ethernet device, such as an Ethernet switch or router. Note If the device is a PoE+ source device, the access point begins to power on and initialize its management software. 3. To use LAN2 port in the static LAG or Cascade mode, connect a second Ethernet cable to the port with these steps. a. Remove the dust plug from the port. Refer to Figure 23. Figure 23. Removing the Dust Plug from the LAN2 Port b. Connect a second Ethernet cable into the LAN2 port. Refer to Figure 24. Figure 24. Connecting the Ethernet Cable to the LAN2 Port 4. Connect the other end to a network device. To use the port as a static LAG with the LAN1 port, connect it to the same router or switch as LAN1 port. To use it in the Cascade mode, connect it to a different device. For an overview, refer to Static Link Aggregation on page 28 and Cascade Mode on page 29. 52 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Note The default setting for the LAN2 port is disabled, To set it to the Static LAG or Cascade mode, use the on-board web browser management interface, explained in the TQ6K GEN2 Management Software User Guide. 5. Do one of the following:

a. If the access point is to be power only by PoE+, without an AC power adapter, go to Attaching the Access Point to the Mounting Bracket on page 55. b. To connect an external AC power adapter, go to Connecting the AC Power Adapter. 53 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point Connecting the AC Power Adapter The access point can be powered with PoE+ on the LAN1 or/and LAN2 ports, an AC power adapter, or both. A wireless access point that is powered by both methods uses the AC adapter as its primary power and PoE as redundant power. For an AC power adapter, Allied Telesis recommends the AT-MWS0091 Power Adapter. If you purchased a power adapter for the wireless access point, perform the following procedure. Otherwise, go to Attaching the Access Point to the Mounting Bracket on page 55. Perform the following procedure to install an AC power adapter:

1. If the AC power adapter has replaceable AC plugs, like the AT-MWS0091 Power Adapter shown in Figure 9 on page 32, verify that the current plug on the adapter is the correct plug for your region. If it is not, install the correct AC plug by following the instructions provided with the adapter. 2. Plug the cable from the power adapter into the power connector on the access point. Refer to Figure 25. Figure 25. Connecting an AC Power Adapter to the Access Point 3. Connect the power adapter into an appropriate AC power source. 4. Turn on the Power Switch. Note The Power Switch controls power from the AC power supply. It does not control PoE+ on the LAN1 and LAN2 ports. 5. Go to Attaching the Access Point to the Mounting Bracket on page 55. 54 Draft 3 on June 9, 2021 Attaching the Access Point to the Mounting Bracket TQ6K GEN2 Access Points Installation Guide To attach the wireless access point on the mounting bracket on the wall or ceiling, perform the following procedure:

1. Align the bottom of the access point over the bracket so that the two screws on the bottom of the device fit into the bracket keyholes. Refer to Figure 26. (These are the two access point chassis screws installed in Pre-fitting the Mounting Bracket on the Access Point on page 44.) Figure 26. Installing the Access Point on the Mounting Bracket 2. Slide the access point forward until its screws are seated in the bracket keyhole slots and the bracket thumbscrew is aligned with the screw hole on the front panel. See Figure 27 on page 56 for the access point and bracket orientations. 55 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point Figure 27. Seating the Access Point on the Mounting Bracket 3. Tighten the thumbscrew to secure the access point to the mounting bracket. Refer to Figure 28. Figure 28. Tightening the Mounting Bracket Thumbscrew 56 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide 4. Place the Ethernet cable(s) and power cable (if any) along the cable guides inside of the top cover in the cable hide space. See Figure 29. Figure 29. Fitting the Cables in the Cable Hide 5. Go to Installing an Anti-theft Device on page 58 or Starting the First Management Session on page 59. 57 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point Installing an Anti-theft Device Installation of an anti-theft cable/lock is optional. The access point has a lock port that is compatible with a Kensington lock. The lock port can be used to physically secure the device to a table, wall, or a ceiling. Note Anti-theft devices are not available from Allied Telesis. 1. Follow the instructions provided with the vendors anti-theft device for the installation. See Figure 30 for the Kensington lock port location. Kensington Lock Port Figure 30. Kensington Lock Port Location 2. If you are installing the wireless access point on a wall or ceiling and have not installed in on the mounting bracket yet, go to Attaching the Access Point to the Mounting Bracket on page 55. 58 Draft 3 on June 9, 2021 Starting the First Management Session TQ6K GEN2 Access Points Installation Guide This section contains an abbreviated version of the procedure to start the first management session. For complete instructions, refer to the TQ6K GEN2 Management Software Users Guide. The wireless access point firmware includes a DHCP client. The default setting for the client is enabled. When you power on the access point for the first time, it queries the subnet on the LAN1 port for a DHCP server. If a DHCP server responds to its query, the unit uses the IP address the server assigns to it. If there is no DHCP server, the access point uses the default IP address 192.168.1.230. To start the first management session, perform the following procedure:

1. Start the web browser on your management workstation. 2. Enter the IP address of the wireless access point in the URL field of the web browser. The address is one of the following:

If your network does not have a DHCP server, enter the default address 192.168.1.230. If your network has a DHCP server, enter the IP address the DHCP server assigned to the access point. The wireless access point displays the login prompt. Refer to Figure 31. Figure 31. Login Prompt 3. Enter manager for the user name and friend for the password. The user name and password are case-sensitive. 59 Draft 3 on June 9, 2021 Chapter 2: Installing the Wireless Access Point 60 Draft 3 on June 9, 2021 Appendix A Technical Specifications This appendix contains the specifications for the TQ6K GEN2 Access Points in the following sections:

Physical Specifications Environmental Specifications Power Specifications on page 62 Cable Specifications on page 64 LAN Ports Specifications and Pinouts on page 65 Physical Specifications Table 4. Physical Specifications Parameter Specification Dimensions (W x D x H) 200 mm X 240 mm X 45 mm

(7.9 in. x 9.4 in. x 1.78 in.) To be updated Weight without mounting bracket Less than 1.2Kg (1.54 lbs) To be updated Weight with mounting bracket 00g (0.0 lbs) Environmental Specifications To be updated Table 5. Environmental Specifications Parameter Specification Operating Temperature when powered by AC/DC adapter Operating Temperature when powered by PoE power source 0 C to 45 C (32 F to 113 F) 0 C to 50 C (32 F to 122 F) Storage Temperature

- 25 C to 70 C (- 13 F to 158 F) Operating Humidity 0% to 90% non-condensing Storage Humidity 0% to 95% non-condensing Maximum Operating Altitude 3000 m (9843 ft) 61 Draft 3 on June 9, 2021 Appendix A: Technical Specifications Power Specifications Input Power Specifications To be updated To be updated Table 6 lists the power requirements of the access points. Table 6. Input Power Specifications Parameter Specification Rated Input Voltage Maximum Input Current Average Input Current 12 VDC 0.7 A 0.52 A External AC Adapter Specifications Table 7 lists the power requirements for an external AC/DC adapter. Table 7. External AC/DC Adapter Specifications Parameter Input Voltage Range Input Frequency Rated Output Voltage Rated Output Current Specification 100~240 VAC 50 - 60 Hz

+12 VDC 2 A Temperature Range 0 C to 45 C (32 F to 113 F) Maximum Operating Altitude 3000 m (9843 ft) Note If you decide to use an AC adapter with the access point, Allied Telesis recommends the AT-PWRADP-01 adapter. The adapter is a UL Listed power supply and is compatible with the above specifications while meeting the standards of a separated extra-low voltage (SELV) product. Note The AT-PWRADP-01 adapter is sold separately. 62 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide PoE+ Power Requirements Table 8 lists the PoE+ specifications for the PoE LAN ports. Table 8. PoE+ Power Requirements on LAN Ports PoE LAN ports 25.5 watts Maximum Power Consumption 63 Draft 3 on June 9, 2021 Appendix A: Technical Specifications Cable Specifications The minimum cable requirements for ports LAN1 and LAN2 are listed here. 10Mbps or 100Mbps ports: Standard TIA/EIA 568-B-compliant Category 3 shielded or unshielded cabling. 1G/2.5G/5G ports: Standard TIA/EIA 568-A-compliant Category 5 or TIA/EIA 568-B-compliant Enhanced Category 5 (Cat 5e) unshielded cabling. Note The maximum operating distance of the cables is 100 meters (328 feet). 64 Draft 3 on June 9, 2021 LAN Ports Specifications and Pinouts TQ6K GEN2 Access Points Installation Guide Port Specifications The access point port specifications are shown in Table 9. Table 9. LAN Port Specifications Connector Specification PoE standard - LAN1 and LAN2 IEEE 802.3at (class 4) Port Pinouts The pin signal definitions for ports LAN1 and LAN2 are given here. Figure 32 illustrates the pin layout of the ports. Figure 32. Pin Layout for RJ45 Connector on LAN Port Table 10 lists the pin signals. Table 10. Pin Signals for 100M/1G/2.5G/5G Base-T Connectors Pin 100 Mbps MDI Signal 100 Mbps MDI-X Signal 1G/2.5G/5G Signal 1 2 3 4 5 6 7 8 TX+

TX-

RX+

RX+

RX-

TX+

Bi-directional pair A+

Bi-directional pair A-

Bi-directional pair B+

Not used Not used Bi-directional pair C+

Not used Not used Bi-directional pair C-

RX-

TX-

Bi-directional pair B-

Not used Not used Bi-directional pair D+

Not used Not used Bi-directional pair D-

65 Draft 3 on June 9, 2021 Appendix A: Technical Specifications 66 Draft 3 on June 9, 2021 Appendix B Regulatory Statements This appendix contains the following regulatory statements:

Federal Communication Commission Interference Statement on page 68 Industry Canada Statement on page 70 Europe - EU Declaration of Conformity on page 72 UK - UKCA Declaration of Conformity on page 73 67 Draft 3 on June 9, 2021 Appendix B: Regulatory Statements Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E80 Caution Avertissement de la FCC: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. E80 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The device is restricted to indoor use only and can be operated within 2412MHz to 2462MHz, 5180GHz to 5320GHz, 5500GHz to 5720GHz, and 5745GHz to 5825GHz. Selection of other channels is disabled. Professional installation is required.The device meets all the other requirements specified in Part E, Section 15.407 of the FCC Rules. 68 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. 69 Draft 3 on June 9, 2021 Appendix B: Regulatory Statements Industry Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-

exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lemetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

(1) Lappareil ne doit pas produire de brouillage.

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la Class B est conforme la norme NMB-003 du Canada. Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-

5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

(iii) the maximum antenna gain permitted for devices in the band 5725-

5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and

(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated.

(v) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-

5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. 70 Draft 3 on June 9, 2021 TQ6K GEN2 Access Points Installation Guide Avertissement:

Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 5 350 MHz et de 5470 5725 MHz doit tre conforme la limite de la p.i.r.e;

(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;

(iv) les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, et nonce la section 6.2.2 3), doivent tre clairement indiqus.

(v) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--

d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. 71 Draft 3 on June 9, 2021 Appendix B: Regulatory Statements Europe - EU Declaration of Conformity Operating Frequencies and Maximum Transmission Power Levels Hereby, Allied Telesis declares that the radio equipment type

[ AT-TQ6702 GEN2, AT-TQm6702 GEN2, AT-TQ6602 GEN2, AT-TQm6602 GEN2] is in compliance with Directive 2014/53/EU. The operating frequencies and maximum transmission power levels for wireless devices operated in the EU are listed below:

- 2412-2472 MHz:

- 5150-5250 MHz:

- 5250-5350 MHz:

- 5470-5725 MHz:

xx.xx dBm (Beamforming), xx.xx dBm (Non-Beamforming) xx.xx dBm (Beamforming), xx.xx dBm (Non-Beamforming) xx.xx dBm (Beamforming), xx.xx dBm (Non-Beamforming) xx.xx dBm (Beamforming), xx.xx dBm (Non-Beamforming) Note Operations in the 5.15 - 5.35 GHz band are restricted to indoor usage only. Radiation Exposure Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of xx cm between the radiator and your body. Importer Allied Telesis International BV Incheonweg 7, 1437 EK Rozenburg Note Contact Allied Telesis for the EU conformity statement. To contact Allied Telesis, visit our web site at www.alliedtelesis.com/contact. 72 Draft 3 on June 9, 2021 UK - UKCA Declaration of Conformity TQ6K GEN2 Access Points Installation Guide Operating Frequencies and Maximum Transmission Power Levels Hereby, Allied Telesis declares that the radio equipment type

[AT-TQ6702 GEN2, AT-TQm6702 GEN2, AT-TQ6602 GEN2, AT-TQm6602 GEN2] is in compliance with the Radio Equipment Regulations 2017 The operating frequencies and maximum transmission power levels for wireless devices operated in the EU are listed below:

- 2412-2472 MHz:

- 5150-5250 MHz:

- 5250-5350 MHz:

- 5470-5725 MHz:

xx.xx dBm (Beamforming), xx.xx dBm (Non-Beamforming) xx.xx dBm (Beamforming), xx.xx dBm (Non-Beamforming) xx.xx dBm (Beamforming), xx.xx dBm (Non-Beamforming) xx.xx dBm (Beamforming), xx.xx dBm (Non-Beamforming) Note Operations in the 5.15 - 5.35 GHz band are restricted to indoor usage only. Radiation Exposure Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of xx cm between the radiator and your body. Importer Allied Telesis International BV 11 Pine Court, Kembrey Park Swindon Wiltshire SN2 8AD, United Kingdom Note Contact Allied Telesis for the UK conformity statement. To contact Allied Telesis, visit our web site at www.alliedtelesis.com/contact. 73 Draft 3 on June 9, 2021 Appendix B: Regulatory Statements 74 Draft 3 on June 9, 2021

Allied Telesis K.K 2nd. TOC Bldg.7-21-11 Nishi-Gotanda, Shinagawa-ku Tokyo 141-0031 Japan Class Il Change Letter Date: 2022/2/9 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To Whom It May Concern:

Request for Class Il Permissive Change FCC ID: RSL-TQ6602GEN2 / Grant Date: 01/28/2022 Pursuant to CFR 2.1043, Allied Telesis K.K hereby requests a Class Il Permissive Change. Modification:

1. Adding U-NII-2A and U-NII-2C bands (5250~5350 MHz, 5470~5725 MHz) for this device. 2. Adding 80+80Q0MHz mode. Antenna Composite Gain report is the same as the original filing. There is no change in hardware or in existing RF relevant portion. The product enables U-NII-2A and U-NIl-2C bands via Firmware by factory. There is no any software that can be modified by end-user. Respectfully, Applicant's company name : Allied Telesis K.K

: 2nd. TOC Bldg.7-21-11 Nishi-Gotanda, Shinagawa-ku Tokyo Applicant's company address 141-0031 Japan Signature ; 7, wan 7. Name and Job Title > Shunji Taki / Director E-Mail : staki@allied-telesis.cojp Tel : +81 3 5436 8350 Fax : +81 3 5436 8351

Allied Telesis K.K 2nd. TOC Bidg.7-21-11 Nishi-Gotanda, Shinagawa-ku Tokyo 141-0031 Japan Confidential Letter Date: 2022/2/9 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID : RSL-TQ6602GEN2 To Whom It May Concern:

Long Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby respectfully request confidential treatment of information accompanying this application as outlined below:

e Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We understand that pursuant to Rule 0.457, cisclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. short Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, we hereby respectfully request short-term confidential treatment of information accompanying this application as outlined below until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

e Test Setup photos Respectfully, Applicants company name : Allied Telesis K.K Applicant's company address : 2nd. TOC Bldg.7-21-11 Nishi-Gotanda, Shinagawa-ku Tokyo 141-0031 Japan Signature Lars Zs Name and Job Title : Shunji Taki / Director E-Mail : staki@allied-telesis.co.jp Tel : +81 3 5436 8350 FOX > +81 35436 8351

Allied Telesis K.K 2nd. TOC Bidg.7-21-11 Nishi-Gotanda, Shinagawa-ku Tokyo 141-0031 Japan Power of Attorney Date: 2022/2/9 Dear Sir,

| hereby have entrusted the following person to be a proxy regarding application for Type Certification. Sporton International Inc. Hsinchu Laboratory Address : No.8, Lane 724, Bo-ai St., Jnubei City, HsinChu County 302, Taiwan, R.O.C. Name : Leo Huang Job Title =: Manager e-mail : Leohvang@sporton.com.iw

| am therefore responsible for the contents of the application. FCC ID: RSL-TQ6602GEN2 Respecitully, Applicant's company name : Allied Telesis K.K Applicant's company address : 2nd. TOC Bidg.7-21-11 Nishi-Gotanda, Shinagawa-ku Tokyo 141-0031 Japan Signature : 4 ia Name and Job Title > Shunji Taki / Director E-Mail : staki@allied-telesis.co.jp Tel > +813 5436 8350 Fax : +81 35436 8351

Allied Telesis K.K 2nd. TOC Bidg.7-21-11 Nishi-Gotanda, Shinagawa-ku Tokyo 141-0031 Japan TPC Declaration Letter Date: 2022/2/9 FCC ID : RSL-TQ6602GEN2 To Whom It May Concern:

We, Allied Telesis K.K, declare that the device supports the TPC function in final F/W when EUT is sold to FCC market. Respectfully, Applicants company name : Allied Telesis K.K

; 2nd. TOC Bldg.7-21-11 Nishi-Gotanda, Shinagawa-ku Tokyo Applicant's company address 141-0031 Japan Signature 7 ao SH. Pe Name and Job Title > Shunji Taki / Director E-Mail : staki@allied-telesis.co.jp Tel > +813 5436 8350 Fax > +81 3 5436 835]

LSESI9EVS EIS - xb4 OSES FEPG E IB+ - lol Afoo'sisaja{-Psl|OOM|Ojs : IOW-3 JaBpunW / PO] unus : SHHT QOP PUD SUDN pt 7 SINLOUBIS updor | eo0er |

OAAWO] NA-DMDBDUIYS DPULJLOS-IUSIN LL-LZ-/BPIg DOL PUuZ =: sseuppoO AUDdWwod s JuboIIddy YY Sisoje} Pay: auiou Aupduwuod $s Juboddy Anjpoedsey sJONUDW sIesy) @

soloud dnjes ise, SOJOUd JOWUISju] =

SOJOU, JOUIS|Xq@

SQOIASP Buf JO HUA UO JONJOD SU! [UN JOUSPYUOS SUIDLUSJ UOLLOUUOJU! SSOUISNG SAIISUSS DINSUS O} JODIO Ul UOILOZUOUINY JUSLUCINY Jo d}oOq JUDID SU} JeyO SADD OBL [HUN MO[SG PSUI|LNO so UOHDOOIddpd siuj BUIAUDCWUODDD UOLOUUOJU! JO JUDLULOSI, JOUEPYUOD UUSI-LOUSs JseNnbeal AlINjpoedsal AQSJ@Y OM SOINY $,UOISSILULUOD SUL JO 6GP'Q PUD /GPQ SUDOSS Of fuIDNSINd HIDYUSPHUOD Wel HOUS UOHDOIICAD siuj JO} JUDI) SUL JO SLOP Sul SIOJOG SPNW sq JOU JIM UOLLOLUSLUNDOp BulAUDdlU0950 I/D PUu_ UOHDoIAdy slul JO DINSOIOSIP /G7'O BINY OL JUDNSINd LOUL PUDISIOPUN SAA

"SIOJHOCUUOD SI! Of Sf ous peylsalun eplaoid pub jUDoIddy eu} Of jnjuUOY aq JUHI Sle}pOlU SseU} JO SINSOJOSIP DyQnd sul oNgnd SUL Of PESDSJO1 AJUDLUOJSND LOU UOHOUUOJU!] AIOJOUCOId PUD S{SIO@S SPN, UIDLUOD s|OUSpOLU SACgHD sul UOYdUOSSC jOUCHOIEdD SOWOWSYDS sWIDIBDIG yDo|g =

MO[EG PSUIILNO sO UO!POOIddD siu, BUIAUDCdLUODDD UOHDOULOYJU! JO [USLULOSI} JOMUSPYUOSD jsonbol Aynjoedsal AQelay OM SOINY S,UOISSIUULUOD SU} 10 6GP'Q PUD /GP'Q SUOIIODSS Of JUDNSINg HIDHUSPYUOD Ue] OU07

[WUIBDUOD ADW }] WIOUAA OL CNAOCOPPOL TSA Gl ODA AfJOUUSPYUOD JO} JsSanbey :yoalqns 9VOLE CW BIQUIN|OD POY SIIW PUBPIDO Gers UOISSILIWIOD SUOLLODIUNLULUOD |OIOpe4 8/ZL/ 170 se}Oq JOYE] |OUSPYUOD updpr Leoderl OAXOL Ny-pMoBHoulys OpuDjos-1ysIN L 1-1-2 6PIg DOL Puz MH SISS[SL PelV

LSE89ErPSeElLBtr : XD4 OSES 9EPSELB+ : [OL Cfoo's|sajaf-PsyJOOMoIs | IOW-J JaBouow / 0) unys : SILL Gor PUD SWION Za 8 SINLOUBIS updor Leo0er |

OAJOL NY-OMPBHDUIUS DPULLOD-IUSIN | L-LZ-ZBpig DOL pug : sseuppo Aupdwods s Jupoyddy YY SISSJO} PONY: alupu AUpdWOo s JuDoIddy Anjpoedsoy CNADTOPIOL-1SA -Cl ODS UOHDOIAAD Su] JO S[UBJUOD SU] JO} BIQlsuUOdsal SJOJSIOUJ LOD |

ML Woo UOLOds@Bunnyoes] : [lOlw-9 jeaBouow : al gor BUONH O87] =: SUION D'O'Y UDMID] ZOE AFUNOD NYOUISH ALID IeqnuP }s 10-Og yZZ BUD] BON : ssouppY Alopo1OgD] NYDUISH Du] |DOUOIJOUJaJU] UOLOdS UOHDOYIS SCA] JOj UOYDOIddp Buipinbai Axoid Dp 9q oj UOSISd Bulmoyo} Su} pejsnujus SADY AQqalay |

WIS IDNq 8/Z1/1Z0% -840q ASUIOYY JO JOMO uvdpr LeooerL OAXO] Ny-DMPBHouIUS DPU_JOS-IYSIN LL-L7-Z'BPIg DOL Puz WHA SISS[SL Pelilv

GES IEVS EC LS+ xb4 OSES 9EPSE 18+: I21 dfoo'siss|af-PayjoOnoys jow-g seBoupw / PL funys : SILL Gor PUD SWON Cx OL SinpouBbis updor [eo0er |

OAIO] NI-OMOEBdDulys OPUDLOD-IUSIN L1-|Z-/,BPig DOL Pug : sselppo AUDdLWOd s,jUuDoI\ddy YY SISsje] PSY: Slupu Aupdwoo s jupojjddy Alinjpoedse y SUOIS |IDJO1 YBNosu Syqnd joseueb oul Of ALOSIP PJOS Sq JOU ]IIM DUD JONPOI SIE |POLSU! OL JOUOISSeJOId PSuIO |OlOSds sOY YSIUM JOUUDYS UOLLNLISID PS|OULUOD YBNOIU] PS|NQuUIsIp Sq ||IM LonPold Sut JOU, sIDJOSep AGeleY SMA JONPOIC Su! Hulpolsul DUD BuunByuos ul jouoissejoud Peuroly joloeds pseu IM JONpold siul Lonpoud siut Ag paleo} UdOUN) PUD JaIOW SNbIUN SU! OC] ANP JOU] PasIADDO 9q asDeld

[WUIBOUOD ADW jf] LUOUM OL CNAOZOPPOL-TSa + Cl DD4 8/71/1707 -840q UONDJD]D9Q UOLDI]|DJSu| |OUOISSajOlg updor Leader! OAI0 Ny-DMDBoulUs DpUu_joy-IYsIN LL-LZ-Z'BPid DOL Puz WH SISSPSL PelllV

LSES9EPS Ee 18+: xb4 OSES 9EPSEIS+ | [2]

dfoo'sisajaf-palJOO Nols: lOW-3 ieBounw / OL Hunus : SILL GOP PUD SWION

Sin,ouBblis updor |Q0er |

OAAJO] NY-OMOBDUIUS OPULDIOD-IUSIN | L-LZ-/BPIG DOL PpuZ : ssouppo Aupdwods s,jupoyddy YY SISOS, PONY: euubu Aubdwos s Jupoiddy Ainjjoedsey BINDSDOIg DOCS 10] Dsyddlp sins DD4 Sut YIM AJAWOD ALUaNbasuod jjOUs JONDOIC jOULL SUL (LELLM] equunu UClOUBISSP DD LO-LESTSLG4 ON Hodel UOLIOdS) saunpeDoJd ALUUIOJUOD JO UOIPOID|Oaq Suall|ddns eu} J@DUN PSZUOULND Useq soy UOILOd SHISOAUWIOD OU JOU} SIOIOSP Of O>I] PINOM (ZNAD ZOPPWOL-LV CNAO ZOPPOLLV ON JSPOW / SIS}9L PSlIlV <SWON Puddg / ZNIDZOIIOL-TSA :G! DD4) {O9loud siuj Jo SapUHGH Sul sd yy SISB}9] PSIIIY OM 8/ZL/LZ0% -O400 J9}97] UOHDISoHW DOdS uodpr Leooerl CAO Ny-OM_BoUulYS DPUDJOD-IYSIN LL-LZ-Z6PId DOL Puz MO SISSPSL PSIIV