all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User Manual | Users Manual | 891.32 KiB | / April 01 2016 | |||
1 2 | Cover Letter(s) | / April 01 2016 | ||||||
1 2 | Cover Letter(s) | / April 01 2016 | ||||||
1 2 | External Photos | / April 01 2016 | ||||||
1 2 | Internal Photos | / April 01 2016 | ||||||
1 2 | ID Label/Location Info | / April 01 2016 | ||||||
1 2 | Cover Letter(s) | / April 01 2016 | ||||||
1 2 | RF Exposure Info | / April 01 2016 | ||||||
1 2 | Test Report | / April 01 2016 | ||||||
1 2 | Test Report | / April 01 2016 | ||||||
1 2 | Test Setup Photos | / April 01 2016 | ||||||
1 2 | Cover Letter(s) | / April 01 2016 | ||||||
1 2 | Cover Letter(s) | / April 01 2016 | ||||||
1 2 | RF Exposure Info | / April 01 2016 | ||||||
1 2 | ID Label/Location Info | / April 01 2016 | ||||||
1 2 | Test Report | / April 01 2016 | ||||||
1 2 | Test Report | / April 01 2016 |
1 2 | User Manual | Users Manual | 891.32 KiB | / April 01 2016 |
Users Guide Wireless LAN Access Point Model No. EA-7HW02AP1 EA-7HW03AP1 Wireless LAN Access Pointwave1 EA-7HW02AP1 Wireless LAN Access Pointwave2 EA-7HW03AP1 Before operating this product, please read the instructions carefully and save this manual for future use. Introduction Thank you for purchasing the Panasonic Enterprise Wireless LAN Access Point. This Users Guide described the instructions for the Enterprise Wireless LAN Access Point. Before connecting, operating or adjusting this product, please read these instructions completely, and save this manual for future use. Trademarks and registered trademarks Wi-Fi is a trademark of the Wi-Fi Alliance. Ethernet is a trademark of Fuji Xerox Co.,Ltd. All other company names and product names in this document are trademarks or registered trademarks of their respective companies. Notice Disclaimers The content of this document is subject to change without notice to improve. All of "Access point", "AP", "Wireless unit", "EA-7HW02AP1" and "EA-7HW03AP1" indicate Wi-Fi base station for business use.
"PoE injector" indicates the option item "EA-7HW00PWR1".
"PoE power feeding device" indicates the option item "EA-7HW00PWR1" or a PoE injector/power feeding hub on the market. Panasonic shall have no liability for any economic damage resulting from communication loss or recording failure caused by a fault, malfunction, failure of this product or by external factors upon power outage. Panasonic shall have no liability for any damage caused by disaster such as earthquakes, lightnings, storm and floods, fire, actions by a third party, other incidents, accidents arising from customers' intentional or negligent misuse and use under abnormal conditions, and for any incidental loss arising from availability or unavailability of this product. This product is not intended to be used with any medical equipments, life-support systems, air traffic control devices and any other device, equipments and systems involving human lives. Panasonic shall have no liability for any damage and loss caused by using this product with these devices, equipments and systems. 2 Safety Precautions To prevent severe injury and loss of life/property, read this section carefully before using the unit to ensure proper and safe operation of your unit. WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. To prevent injury, this apparatus must be securely attached to the wall/ceiling in accordance with the installation instructions. All work related to the installation of this product should be made by qualified service personnel or system installers. The installation shall be carried out in accordance with all applicable installation rules. The connections should comply with local electrical code. CAUTION:
Compliance with FCC requirement 15.407(c) Data transmission in always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. Frequency Tolerance: 20 ppm This device is restricted for indoor use. This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. AC adaptor with ferrite core must be used for RF interference suppression. 3 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. 4 Contents 1. Specifications 13 1.1. Equipment specifications 14 1.2. Appearance/Dimensions(Specifications of this product are subject to change without notice) 16 1.3. Major Operating Controls and Their Functions 23 1.4. Power feeding method 31 Interface specifications 32 1.5. 2. EA-7HW02AP1 installation work 35 2.1. Installations and Connections 36 2.2. Determine the installation place of wireless unit 37 2.3. Installation work of wireless unit 38 2.4. Connections 40 2.5. Initialization 42 2.6. Alarm display by self-test 43 3. EA-7HW03AP1 installation work 44 3.1. Installations and Connections 45 3.2. Determine the installation place of wireless unit 46 3.3. Installation work of wireless unit 47 3.4. Connections 50 3.5. Initialization 52 3.6. Alarm display by self-test 53 4. Setting method 54 4.1. Setting of PC for Web console use 55 5. Response to error occurrence 60 5.1. Troubleshooting 61 5 Main unit and accessories The main unit and the following accessories are contained in the package box. Make sure that all of them are contained when opened the package. EA-7HW02AP1 Product name Total number Illustration Remarks Main unit AC adapter AC cable Stand Mounter Safety guide 1 1 1 1 1 1 6 EA-7HW03AP1 Product name Illustration Total number Remarks Main unit AC adapter AC cable Mounter M6 screw M3 screw Rubber foot Safety guide 1 1 1 1 4 1 4 1 Shipped after attaching to the main unit Important 1. In addition to the above, the following are required to perform the installation work. The following are not provided with this product. Please procure separately. Ethernet cable (Category 5e or better, with RJ-45 modular plugs on both ends) 2. This product (EA-7HW02AP1/ EA-7HW03AP1) is water-resistant (JIS C 0920 Protection grade 2, drip-proof type II). Avoid direct water jet and do not submerge this product in water when performing the installation work. When installing in a place where water can splash onto this product, to protect the product from water, make sure to install the product upright with the LED on the left side. (Do not lay the product on its side when installing and do not install the product in any way other than the above when installing it upright.) 7 To run a radio station of the second generation low-power data communication system as an outdoor fixed station, it is required to display both the name the owner of the corresponding radio station (or the name of the service provider) and the contact address. The following are the content to be displayed. Display of radio station: Radio station of 2.4 GHz band low-power data communication system Name of owner or of service provider Contact address: Phone number or E-mail address (or home page address, etc.) Other useful information such as information to avoid radio wave interference, etc. As for method of display, use a sticker or a plate, print or handwrite on a place where no special operation is required to see such as on the radio station or on the housing case. 8 Option (Sold separately) PoE injector The following options are available to use EA-7HW02AP1 more conveniently. Contact your dealer from whom you purchased this product for purchasing. Product name
<Model no.>
PoE injector
<EA-7HW00PWR1>
Illustration Total number 1 9 Precautions for use Incorrect installation may cause tip-over resulting in accidents. The installation work must be carried out by a professional installer. Turn the power off when cleaning this product. Use a soft cloth to clean this product. When dust is hard to remove, use a soft cloth soaked in diluted detergent and squeezed hard to wipe it, and then wipe with a dry soft cloth. Do not use any of alcohol, petroleum, thinner, benzene, boiling water, polishing powder and soap powder for cleaning and maintenance. When using a chemical cloth for cleaning, read the caution provided with the chemical cloth product. Do not place this product in a place where temperature is high such as a place near a heating equipment or a boiler. Failure to observe this may result in deformation/deterioration of the surface/parts of the product or cause a failure. Do not bring fire close to the product. Failure to observe this may result in deformation/deterioration of the surface/parts of the product or cause a failure. Do not place this product in a place where hydrogen sulfide, phosphorus, ammonia, sulfur, carbon, acid, dust or noxious gas can exist. Failure to do so may result in failure or shorten the life of the product. Do not place this product near a source of electromagnetic wave or a magnetized object.
(High-frequency sewing machine, electric welder, magnet, etc.) Failure to observe this may result in generation of noise or cause a failure. Do not apply a strong impact or vibration to this product. When disposing of this product, handle it as an industrial waste and follow laws and regulations If a strong impact caused by a fall or a strike is applied, it may result in a failure or a damage. appropriately. 10 Notes on radio waves This product is certified to radio equipment technical standards based on Radio Act (2.4 GHz ISM band low-power data communication system and 5 GHz band low-power data communication system). Therefore, no license of a radio station is necessary for use of this product. Since this product is certified to the technical standards, the following actions are punishable by law. Taking apart or modifying this product. (Alteration of frequency and antenna is prohibited.) Removing the certification label from the bottom of this product. 5 GHz band (IEEE802.11 a/n/ac) in outdoor use is limited in usable frequency by Radio Act. Applicable channels of 5 GHz (IEEE802.11 a/n/ac) band are ch36 - ch48 (W52), ch52 - ch64 (W53) and ch100 - ch140 (W56). W52 and W53 are only for indoor use. W56 is usable for outdoor use. Do not select W52 and W53 when configuring the settings in case of using this product outdoor. To support W53 and W56, DFS (Dynamic Frequency Selection) and TPC (Transmit Power Control) are used as the radio wave control function. It is impossible to communicate with a wireless LAN equipment using the channel (J52) which was released before the ordinance was revised in May 2005 due to channel mismatch. In the use frequency band of 2.4 GHz band (IEEE802.11 b/g/n), in addition to industrial/scientific/medical equipments including microwave ovens, private branch radio stations (license required) for mobile object identification that are used in manufacturing lines at factories, specified low-power radio stations (no license required) and amateur radio stations (license required) are being operated. Before using this product, make sure that any of private branch radio station for mobile object identification, specified low-power radio station and amateur radio station is not being operated. If harmful radio wave interference against a private branch radio station for mobile object identification caused by this product occur, immediately change the use frequency of this product and eliminate the radio wave interference. When operating this product in 2.4 GHz band, it is recommended to select CH1, CH6 or CH11 for the channel setting to reduce interference and to improve frequency utilization efficiency. If you need any assistance to deal with a trouble such as harmful radio wave interference against a private branch radio station for mobile object identification or a specified low-power radio station caused by this product, contact your dealer from whom you purchased this product. Use frequency band: 2.4 GHz Modulation system: DS-SS/OFDM Estimated interference distance: Less than 40 m Frequency change availability: It is possible to avoid band for private branch radio station for mobile object identification and specified low-power radio station while using the entire band. The following marks indicating these are labeled on the product. 11 Security-related notice on use of wireless LAN products In a wireless LAN, information is transmitted/received between a PC and this product using radio wave instead of a LAN cable. Therefore, it has an advantage that the LAN connection is always available in a range which radio waves reach. On the other hand, since radio waves get over obstacles (wall, etc.) and reach any place within a certain range, the following problems can occur if settings relating to security are not configured. Content of communication can be peeped There is a possibility that a third person with malicious intention may intentionally pick up radio waves and monitor content of communication including personal information such as ID, password, credit card number and content of E-mails. Illegal intrusion There is a possibility that the following may be brought by illegal intrusion. A third person with malicious intention may invade and access a personal or a corporate network to steal personal information or classified information (information leakage). Communicate by impersonating a specific person and spread illegal information (Spoofing) Edit monitored content of communication and transmit (Alteration) Spread computer virus and destroy data or a system (Attack) Since a wireless LAN card and this product originally have security countermeasures against these problems, the possibility of occurrence of these problems may be reduced if wireless LAN products are used after configuring the security-related settings of the products. Fully understand problems that may occur if using the product without configuring the security-related settings. It is recommended to use this product after configuring the security-related settings on your own judgement and responsibility while taking other countermeasures (use of physical security countermeasure against theft or use of VPN function to prevent data eavesdropping) according to your use environment. 12 Chapter 1. Specifications The following are descriptions about specifications of Wi-Fi base station for business use. 13 1.1. Equipment specifications Wi-Fi base station for business use EA-7HW02AP1 External interface Frequency Item Wireless Wired 2.4 GHz 5 GHz Transmission power Antenna Antenna gain Wireless LAN function Network Interface Maintenance function Power source Power consumption Required operating environment Water-/dust-resistance Outer dimensions (excluding tolerance and projections)/Weight EA-7HW02AP1 IEEE802.11b/g/n, IEEE802.11a/n/ac (wave1) (Simultaneous use is possible.) 10/100/1000BASE-T 1 port 2412-2462MHz 5180-5240, 5260-5320, 5500-5700, 5745-5825 MHz. Maximum 2.4GHz: 28.23 dBm / Maximum 5GHz: 27.82 dBm. Planar inverted F antenna 2.4 GHz: 3.88 dBi/ 5 GHz: Less than 5 dBi Multi-SSID (16), WEP/WPA2 (Personal/Enterprise), MAC authentication, WMM L2 bridge, L2/L3/L4 filtering, VLAN, PPPoE, IPsec Telnet, SSH, Web, FTP/SFTP, SNMP/TRAP, NTP, syslog 12 V DC PoE(IEEE802.3af) 12.95 W or less Temperature: 0 C- 40 C Humidity: 5 % - 95 % (non condensing) IP42 (except the rear panel) W159 mm x H159 mm x D29 mm /
Approx. 360 g 14 Wi-Fi base station for business use EA-7HW03AP1 EA-7HW03AP1 IEEE802.11b/g/n, IEEE802.11a/n/ac (wave2) (Simultaneous use is possible.) 10/100/1000BASE-T USB 3.0 2 ports Item External interface Frequency Wireless Wired USB 2 ports Maintenance Console interface 2.4 GHz 5 GHz 1 port Power consumption Required operating environment Temperature: 0 C - 40 C 1ch - 13ch W52, W53, W56
(Outdoor use of W52 and W53 is prohibited by the ordinance ) 2.4 GHz: 17 dBm/ 5 GHz: 15 dBm (W52/53), 18 dBm (W56) Planar inverted F antenna 2.4 GHz: 4 dBi/ 5 GHz: Less than 5 dBi Multi-SSID (16), WEP/WPA2 (Personal/Enterprise), MAC/ authentication, WMM L2 bridge, L2/L3/L4 filtering, VLAN, PPPoE, L2TPv3, IPsec Telnet, SSH, Web, FTP/STFTP, SNMP/TRAP, NTP, syslog 24 V DC PoE (IEEE802.3af, IEEE802.3at) When using IEEE802.3af Use of USB and 2.4 GHz band becomes unavailable. When using IEEE802.3at Use of USB becomes unavailable. 25.5 W or less
(0 C - 50 C Only when installing on a wall) Humidity: 5 % RH - 95 % RH (non condensing) IP42 (except the rear panel) W201.7 mmH201.7 mmD38.5 mm (excluding tolerance and projections) Approx. 990 g Specifications 100 V - 240 V AC However, the provided power cord is only for 100 V AC. Prepare a power cord separately when using 200 V AC power supply. 24 V DC/36 W Temperature: 0 C - 40 C
(0 C - 50C Only when 1 USB port of this product is not being used) Humidity: 5 % RH - 90 % RH (non condensing) W 48 mmH 109 mmD 34 mm
(Excluding tolerance and projections) Approx. 300 g 15 Transmission power Antenna Antenna gain Wireless LAN function Network Interface Maintenance function Power source Water-/dust-resistance Outer dimensions Weight AC adapter Item Input voltage Output voltage/power Required operating environment Dimensions Weight 1.2. Appearance/Dimensions
(Specifications of this product are subject to change without notice) EA-7HW02AP1 Main unit Outline view
(Unit: mm) 5
. 2 9 5 1 291.0 1592.5 16
(Unit: mm) 0
. 1 4 2 5
. 1 4 8 Mounter Outline view 5
. 2 1 3 1 4.30.5 81.0 1312.5 17 Stand Outline view
. 5 1 2
. 6 5
. 5 1 9
. 6 6 1222.5 18 AC adapter Outline view
(Unit: mm) 28.51.0 95.91.5
. 5 1 8
. 3 4 19 EA-7HW03AP1 Main unit Outline view
(Unit: mm)
. 5 2 7
. 1 0 2 38.51.5 201.72.5 20 Mounter Outline view
(Unit: mm) 117.51.5 60.5 0
. 1 5
. 1 1 5
. 1 2
. 6 1 1
. 5 2 5
. 2 7 1 26.81.0 1352.5 21 AC adapter Outline view 1200 +150
-50 341.5 Power cord Outline view 100035
(Unit: mm) 1091.5 5
. 1 8 4 22 1.3. Major Operating Controls and Their Functions Wi-Fi base station EA-7HW02AP1 The following are descriptions about the appearance of this product and names/functions of each operating control. Mounter To be used when mounting on a wall/ceiling. Rear Status LED Indicates the status of the wireless unit. MAC address Displayed on the nameplate on the rear.. Stand To be used when installing on a table.
(5) INIT switch
(1) ACT LED
(2) 5G LED
(3) 2.4G LED
(4) ETH LED
(7) DC IN connector
(6) LAN connector 23 Descriptions about each LED, switch and connector are in the following table. No.
(1) ACT LED Signal
(2) 5G LED
(3) 2.4G LED
(4) ETH LED
(5)
(6)
(7) INIT switch
(Push switch) Ethernet IF ETH
(RJ-45 modular jack) DC IN jack Function Error detection during operation In operation Indicates the operational/error status of the unit. Lights red Lights green Displays the status of wireless IF 5 GHz In normal operation Lights green Off In the process of start-up Displays the status of wireless IF 2.4 GHz In normal operation Lights green In the process of start-up Off Indicates the link status of the Ethernet port. Blinks green Lights green Off Initializes configuration data and log data. In the process of frame transmission/reception Link established Link disconnected Connect an Ethernet cable. The ETH port supports power supply from a PoE power feeding equipment. Connect the DC plug of the provided AC adapter. 24 AC adapter (standard accessory) Connect to the AC outlet to supply power to the wireless unit. AC adapter main unit DC jack AC IN terminal Connect the provided AC power cord. AC power cord 25 Wi-Fi base station for business use EA-7HW03AP1 The following are descriptions about the appearance of this product and names/functions of each operating control. Mounter To be used when mounting on a wall/ceiling. Status LED Indicates the status of the wireless unit. MAC address Displayed on the nameplate on the rear. ACT LED 2.4G LED 5G LED ETH1 LED ETH2 LED 26 Front
(1) ACT LED
(2) 2.4G LED
(3) 5G LED
(4) ETH1 LED
(5) ETH2 LED No.
(1) ACT LED Signal
(2) 2.4G LED
(3) 5G LED
(4) ETH1 LED
(5) ETH2 LED Function In operation In the process of start-up In the process of upgrade Error detection during operation Indicates the operational/error status of the unit. Lights green Blinks green Blinks red Lights red Displays the status of wireless IF 2.4 GHz Lights green In normal operation Off In the process of start-up Displays the status of wireless IF 5 GHz Lights green Off Indicates the link status of the Ethernet port. Blinks green Lights green Off Indicates the link status of the Ethernet port. Blinks green Lights green Off In normal operation In the process of start-up In the process of frame transmission/reception Link established Link disconnected In the process of frame transmission/reception Link established Link disconnected 27 Rear/Left side
(1) INIT switch
(2) CONSOLE
(3) MODE switch
(4) DC IN jack
(5) ETH2
(6) ETH1 (PoE)
(8) Claw (x4)
(7) Holder Signal INIT switch
(Push switch) CONSOLE
(RJ-45 connector) MODE 1, 2
(Slide switch) DC IN jack ETH2
(RJ-45 connector) ETH1( PoE) connector
(RJ-45 connector) Holder Initializes configuration data and log data. Function Connect the console for maintenance, such as a PC. Not be used. Do not change the default. Connect the DC plug of the provided AC adapter. Connect an Ethernet cable. Connect an Ethernet cable and start power feeding from a PoE power feeding equipment. Use this with a cable tie to prevent disconnection of the AC adapter. Claw (x4) Attach by tightening the provided M6 screw when installing on a wall. 28 No.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) Bottom side
(1) Kensington lock
(2) Mounter fixing hole
(3) USB2
(4) USB1 Signal Function Kensington lock Use for theft prevention. Mounter fixing hole Attach the mounter. USB2
(USB3.0 Type A) USB1
(USB3.0 Type A) Connect a USB device. Connect a USB device. No.
(1)
(2)
(3)
(4) 29 AC adapter (standard accessory) Connect to the AC outlet to supply power to the wireless unit. AC power cord AC adapter main unit DC jack AC IN terminal Connect the provided AC power cord. 30 1.4. Power feeding method Power feeding method The power feeding method of the wireless unit is as follows. Access point EA-7HW02AP1 EA-7HW03AP1 Available power feeding method Power feeding from AC adapter
(Use the supplied AC adaptor.) Power feeding from PoE power feeding equipment compliant with IEEE802.3af or IEEE802.3at. Power feeding from AC adapter
(Use the supplied AC adaptor.) Power feeding from PoE power feeding equipment compliant with IEEE802.3af or IEEE802.3at.
* However, there are following restrictions when using PoE power feeding for EA-7HW03AP1. When using IEEE802.3af Use of USB and 2.4 GHz band becomes unavailable. When using IEEE802.3at Use of USB becomes unavailable. If these conditions are not fulfilled, this product may sometimes be reset. Refer to "2.4.2 Connection with power supply" for power feeding. 31 Interface specifications 1.5. Ethernet interface specifications Interface specifications Type of connector Type of cable Transmission distance RJ-45 RJ-45 Category 5 Enhanced category 5 100 m 100 m Network interface 10BASE-T/100BASE-TX 1 000Base-T LAN (RJ-45) connector 1 2 3 4 5 6 7 8
(Connector on the main unit side) Pin No. 10/100Base Main unit side (MDI) 10/100Base Main unit side (MDI-X) 1000Base-T Main unit side (MDI) 1000Base-T Main unit side (MDI-X) Table 1.6 LAN (RJ-45) connector 1 2 3 4 5 6 7 8 Tx +
Tx -
Rx +
Not used Not used Rx -
Not used Not used Rx +
Rx -
Tx +
Not used Not used Tx -
Not used Not used BI_DA +
BI_DA -
BI_DB +
BI_DC +
BI_DC -
BI_DB -
BI_DD +
BI_DD -
BI_DB +
BI_DB -
BI_DA +
BI_DD +
BI_DD -
BI_DA -
BI_DC +
BI_DC -
32 Console interface specifications (EA-7HE03AP1 only) Console (RJ-45) connector 1 2 3 4 5 6 7 8
(Connector on the main unit side) Table 1.6 LAN (RJ-45) connector Main unit side (DTE) Pin No. 1 2 3 4 5 6 7 8 RTS DTR TxD GND GND RxD Not used Not used 33 USB interface specifications (EA-7HE03AP1 only) Interface specifications Network interface Type of connector Transmission distance USB 3.0 Type-A 3 m USB connector USB connector Pin No. Signal name 1 2 3 4 5 6 7 8 9 V BUS D -
D +
GND TX +
TX -
GND RX +
RX -
34 Chapter 2. EA-7HW02AP1 installation work The following are descriptions about installation work of EA-7HW02AP1 and connection method of each interface. 35 Installations and Connections 2.1. Follow the procedures below to install and connect EA-7HW02AP1. Use EA-7HW02AP1 2.2 Determine the installation place of wireless unit 2.3 Installation work of wireless unit 2.4 Connections 36 2.2. Determine the installation place of wireless unit EA-7HW02AP1 can be installed on a wall, on a ceiling, at back of ceiling and on a desktop using the provided mounter. The wireless unit shall be installed on a place having an enough strength to hold the unit and flat surface. Weight of the main unit of the wireless unit is approx.360 g. Make sure that there is no factor that can affect performance of the antenna, such as a metallic or concrete The wireless unit shall be installed firmly not to loosen up and fall off due vibration and anything in future. obstacle, near the wireless unit. Read "Safety precautions" and "Precautions" carefully and determine the installation place. 37
(1)
(2) Installation work of wireless unit 2.3. Refer to "1.2 Appearance/Dimensions" for the size of the wireless unit and the mounter. 1. Wall mounting
(1) Fixing of the mounter Fix the mounter after making sure that the installation place has an enough strength and flat surface of concrete, metal, wood, mortar, etc. Fasten a screw (x1) temporarily on the installation surface. Make sure that the mounter can be installed in parallel, and then fix it firmly with 2 screws located at the upper and the lower sides.
(Recommended tightening torque: 0.85 Nm 0.12 Nm) Note Use a screw whose nominal diameter is 4mm to fix on the installation surface. This screw shall be prepared by the installer according to the material of the installation surface.
(2) Installation of the wireless unit Fix the main unit onto the mounter fixed on the wall. Hook the claws (x4) of the wireless unit into the hook holes on the mounter. Claw (x4) Hook hole (x4) Align the side of the mounter and the dent in the wiring groove of the wireless unit.
(3) Slide the wireless unit downward until the "click" sound is heard. To remove the wireless unit from the mounter, slide the wireless unit upward while holding down the lever to the wall side. Lever 38 Important When installing the wireless unit, make sure that the LED is not hidden from your view and it is easy to check. Secure a space of 30 mm or more above the product to secure a space allowing you to hook. e r o m r o m m 0 3 Ceiling 2.
(1) Fix the wireless unit onto the stand. Installation on a desktop Hook the claws (x2) on the rear of the wireless unit into the hook hole on the stand. Claw (x2 at the lower side) Hook hole (x2) 39 2.4. Connections 2.4.1. Connection to network 1. In case of LAN connection Connect an Ethernet cable (enhanced category 5 or better) to the LAN connector on the right side of the main unit. LAN connector 2.4.2. Connection with power supply 1. Power feeding from AC adapter Firmly connect the DC plug of the provided AC adapter to the DC IN connector in the external interface section of the main unit. DC IN connector 40 2. Power feeding from PoE unit
(1) Power will be fed from PoE power feeding equipment compliant with IEEE802.3af or IEEE802.3at. In this section, descriptions of how to feed power from PoE injector are provided. By following the procedures below, connect the PoE injector and other cables. Insert the plug of the Ethernet cable connected with the wireless unit to the "DATA & POWER OUT" port of the PoE injector until the "click" sound is heard.
(2) Connect the provided power cable to the PoE injector.
(3) Insert the power plug of the PoE injector to an outlet of 100 V AC. (The POWER LED will light yellow and then turn to green.) Insert the plug of the Ethernet cable connected with a host network device to the "DATA IN" port of the PoE injector until the "click" sound is heard.
(4) Important The wiring length from the wireless unit to the host network device shall be up to 100 m (total). Do not pull the connected cables with a strong force. Do not place a heavy object on the PoE injector. Do not perform wiring of the connection cables and the Ethernet cable connection section in a place where water can damage them. 41 Initialization 2.5. It is possible to initialize (reset the setting data and the log data to the default) the wireless unit directly without using the initialization command.
(1) Hold down the INIT switch using something that has a needle-like tip such as a skewer.
* Start working after removing static electricity.
(2) Connect the AC adapter and the PoE injector, and then turn on the power.
(3) Wait until the ACT LED starts blinking red.
(4) When the ACT LED blinking red turns to blinking green, release the INIT switch. Default of each interface after the initialization Network interface Default Remarks Wi-Fi interface (2.4G) Wi-Fi interface (5G) Ethernet (ETH) Off Off
-
Default after validating the interface 2.4 GHz, 1ch, HT40 Default after validating the interface 5.2 GHz, 36ch, HT80 Default fixed IP (192.168.0.3/24)
(Access will become available after approx. 150 seconds from the start-up.) 42 2.6. Alarm display by self-test This product will automatically perform self-test upon the start-up. If an error is detected, the detected alarm will be indicated by the LED display on the product. When an error is detected on the self-test, turn off the power and contact the dealer from whom you purchased this product. EA-7HW02AP1 Self-test alarm display Alarm type FROM check error RAM check error Manufacturing number error ACT Lights red Lights red Blinks red MAC address error Blinks red 2.4G Off Off Off Off 5G Off Off Off Off ETH As the test of LED, all LEDs except the LINK LED will light. After that, all LEDs except the LINK LED will be off until the self-test finishes. Refer to "1.3 Major operating controls and their functions" for descriptions of LED display when the self-test completed correctly. When started up by turning on the INIT switch (initialized state), the ACT LED will start blinking. The status of ETH LED will change according to the connection status of Ethernet (power supply state). Notice 43 Chapter 3. EA-7HW03AP1 installation work The following are descriptions about installation work of EA-7HW03AP1 and connection method of each interface. 44 Installations and Connections 3.1. Follow the procedures below to install and connect EA-7HW03AP1. Use EA-7HW03AP1 3.2 Determine the installation place of wireless unit 3.3 Installation work of wireless unit 3.4 Connections 45 3.2. Determine the installation place of wireless unit Weight of the main unit of the wireless unit is approx.990 g. Make sure that there is no factor that can affect performance of the antenna, such as a metallic or concrete EA-7HW03AP1 can be installed on a wall, on a ceiling and at back of ceiling using the provided mounter. The wireless unit shall be installed on a place having an enough strength to hold the unit and flat surface. The wireless unit shall be installed firmly not to loosen up and fall off due vibration and anything in future. obstacle, near the wireless unit. Read "Safety precautions" and "Precautions" carefully and determine the installation place. 46 Installation work of wireless unit 3.3. Refer to "1.2 Appearance/Dimensions" for the size of the wireless unit and the mounter. 1. Wall mounting
(1) Attach the M6 screws (x4) to the rear of this product. (Recommended tightening torque: 3.0Nm 0.4 Nm) M6 screw (x4)
(2) Fix the mounter after making sure that the installation place has an enough strength and flat surface of concrete, metal, wood, mortar, etc. Fasten screws (x2) temporarily on the installation surface. Make sure that the mounter can be installed in parallel, and then fix it firmly with 4 screws located at the upper and the lower sides.
(Recommended tightening torque: 3.0 Nm 0.4 Nm) 47 Important Use a screw whose nominal diameter is 5 mm to fix on the installation surface. This screw shall be prepared by the installer according to the material of the installation surface.
(3) Fix this product onto the mounter fixed on the wall. Hook the M6 screws (x4) on the rear into the hook holes on the mounter. M6 screw (x4) Hook hole (x4)
(4) Align the hook hole on the front of the mounter and the M6 screw on the rear of this product.
(5) Hold the both sides of this product and slide it downward.
(6) Thread the M3 screw into the fixing hole firmly. (Recommended tightening torque: 0.6 Nm 0.1 Nm) 48
* To remove the mounter, hold the both sides of this product and slide it upward. 2. Flat installation Install on a flat place. 49 3.4. Connections 3.4.1. Connection to network Connect an Ethernet cable (enhanced category 5 or better) to the ETH1 (PoE) connector or the ETH2 connector on the left side of this product. ETH1 (PoE) connector or ETH2 connector 3.4.2. Power feeding from AC adapter Firmly connect the DC plug of the provided AC adapter to the DC IN connector in the external interface section of this product. 50 1. Power feeding from PoE unit Power will be fed from PoE power feeding equipment compliant with IEEE802.3af or IEEE802.3at. In this section, descriptions of how to feed power from PoE injector are provided. By following the procedures below, connect the PoE injector and other cables.
(1) Insert the plug of the Ethernet cable connected with the ETH1 (PoE) connector of the wireless unit to the "DATA
& POWER OUT" port of the PoE injector until the "click" sound is heard.
(2) Connect the provided power cable to the PoE injector.
(3) Insert the power plug of the PoE injector to an outlet of 100 V AC. (The POWER LED will light yellow and then turn to green.) Insert the plug of the Ethernet cable connected with a host network device to the "DATA IN" port of the PoE injector until the "click" sound is heard.
(4) ETH1( PoE) connector Important The wiring length from the wireless unit to the host network device shall be up to 100 m (total). Do not pull the connected cables with a strong force. Do not place a heavy object on the PoE injector. Do not perform wiring of the connection cables and the Ethernet cable connection section in a place where water can damage them. 51 Initialization 3.5. It is possible to initialize (reset the setting data and the log data to the default) the wireless unit directly without using the initialization command. 1. Hold down the INIT switch using something that has a needle-like tip such as a skewer. 2. Connect the AC adapter and the PoE injector, and then turn on the power. 3. Wait until the ACT LED starts blinking red. 4. When the ACT LED blinking red turns to blinking green, release the INIT switch.
* Start working after removing static electricity. Default of each interface after the initialization Network interface Default Remarks Wi-Fi interface (2.4G) Wi-Fi interface (5G) Ethernet1 (ETH1) Ethernet2 (ETH2) Off Off
-
-
Default after validating the interface 2412MHz, HT40 Default after validating the interface 5180MHz, HT80 Default fixed IP (192.168.0.3/24)
(Access will become available after approx. 90 seconds from the start-up.) Default fixed IP (192.168.0.3/24)
(Access will become available after approx. 90 seconds from the start-up.) 52 3.6. Alarm display by self-test This product will automatically perform self-test upon the start-up. If an error is detected, the detected alarm will be indicated by the LED display on the product. When an error is detected on the self-test, turn off the power and contact the dealer from whom you purchased this product. EA-7HW03AP1 Self-test alarm display Alarm type FROM check error RAM check error Manufacturing number error ACT Lights red Lights red Blinks red MAC address error Blinks red 2.4G Off Off Off Off 5G Off Off Off Off ETH1 ETH2
-
-
-
-
-
-
-
-
As the test of LED, all LEDs except the LINK LED will light. After that, all LEDs except the LINK LED will be off until the self-test finishes. Refer to "1.3 Major operating controls and their functions" for descriptions of LED display when the self-test completed correctly. When started up by turning on the INIT switch (initialized state), the ACT LED will start blinking. The status of ETH1 LED/ETH2 LED will change according to the connection status of Ethernet (power supply state), Notice 53 Chapter 4. Setting method 54 4.1. Setting of PC for Web console use The following are descriptions of how to connect a PC for web console use and of how to configure the setting of this product. Recommended environment of PC for Web console use OS and TCP/IP software Resolution LAN card Web browser Microsoft Windows 7 Microsoft Windows 8.1 TCP/IP software is provided with OS. It is unnecessary to prepare separately. 1024 x 768 pixels or more An Ethernet port is required on the PC in use to connect this product to the PC. When using a LAN card, prepare one that can be installed on your PC. When using web console to configure the settings of this product, prepare the following web browser. Microsoft Internet Explorer 11 or later
* Access to the same AP from multiple web browsers is not supported. Preparation of LAN card Make sure that the PC for web console use has an Ethernet port. No Ethernet port is found. It is required to install a LAN card on the PC. When newly installing a LAN card, installation of software for LAN card
(network driver) is required. Configure the settings correctly by following the manuals provided with the PC and the LAN card. TCP/IP protocol setting When using the web console, it is required to complete the IP address and the subnet mask setting using the PC for web console use. The setting procedure varies depending on OS of the PC. On this document, descriptions are provided supposing Microsoft Windows 8.1 is installed on the PC. Configure the TCP/IP setting of the PC. 55 Setup procedure Step 1 Step 2 Step 3 Step 4 Open the "Control Panel" window and click [Network and Sharing Center]. Click [Change adapter settings]. The "Network Connections" window will be displayed. Double click [Local Area Connection]. The "Local Area Connection Status" window will be displayed. Check if "Internet Protocol Version 4 (TCP/IPv4)" is included in the displayed list. If "Internet Protocol Version 4 (TCP/IPv4)" is not in the list, it is necessary to install TCP/IP. Install it by referring to the manual of Microsoft Windows 8.1. Step 5 Click to select "Internet Protocol Version4 (TCP/IPv4)", and then click [Properties]. 56 Set the IP address of the PC. The IP address and the subnet mask shall be matched with the IP address and the subnet mask set for this product. Refer to the following for the default IP address of this product. Step 6 IP address Subnet mask Default gateway IP address (Default) 192.168.0.3 255.255.255.0 192.168.0.1 The following are examples to explain how to configure the settings. Select "Use the following IP address". Enter "192.168.0.253" for the IP address. Enter "255.255.255.0" for the subnet mask. No entry is needed for the default gateway. Click [OK] and return to "Properties". Step 7 Step 8 Step 9 Click the [Close] button. Click the [Close] button to return to "Local Area Connection Status". 57 Preparation of web browser The setting procedure varies depending on OS of the PC. On this document, descriptions are provided supposing Microsoft Windows 8.1 is installed on the PC. Step 1 Open the "Control Panel"window and click [Internet Options]. The "Internet Properties" window will be displayed. Setup procedure Step 2 Step 3 Select the [Connections] tab and click [LAN settings]. Confirm that the "Use a proxy server for your LAN" check box is unchecked. Local Area Network (LAN) Settings When using a proxy server, configure not to use the proxy server for this product. Step 4 Open the "Control Panel"window and click [Internet Options]. The "Internet Properties" window will be displayed. Step 5 Step 6 Select the [Connections] tab and click [LAN settings]. Check the "Use a proxy server for your LAN" check box and click [Advanced]. 58 Enter the IP address of this product to the "Do not use proxy for addresses beginning with" box under
"Exceptions". Step 7 Step 8 Step 9 Step 10 Click the [OK] button to return to "Local Area Network (LAN) Settings". Click the [OK] button and return to "Internet Properties". Click the [OK] button. 59 Chapter 5. Response to error occurrence 60 5.1. Troubleshooting The following are descriptions of how to connect a PC for web console use and of how to configure the setting of this product. Refer to the following descriptions when an error occurred in this product. Symptom Inspection Solution Isn't the Ethernet cable detached?
Connect ETH to the "DATA & POWER OUT" port of the PoE injector when feeding power from PoE.
(Connect to the power feeding port of the PoE power feeding equipment.) The ACT LED does not light. Isn't the DC plug of the AC adapter detached?
Connect the DC plug to the DC IN port. Isn't the power cord detached from of the AC adapter/PoE injector ?
Connect the power cord to the AC adapter/PoE injector. Isn't the Ethernet cable detached?
Doesn't the Ethernet cable have a breakage?
Isn't there any obstacle blocking communication between the wireless unit and the terminal?
Connect the Ethernet cable correctly. Check if the Ethernet cable works correctly, or replace it. Remove the obstacle or change the installation place of the wireless unit. Isn't the setting configured to hide SSID?
Isn't power supplied to the wireless unit?
Is the setting of the communication software of the console correctly configured?
Follow Use's Guide to cancel the setting to hide SSID or configure the settings to make possible to connect with the Wi-Fi terminal in advance. Make sure that the power of the PoE power feeding equipment or the DC power supply unit is turned on. Follow Use's Guide and configure the setting of the communication software. Are the login name and password correct?
Retry to log in using the correct login name and password. Check if the settings are appropriate. Follow Use's Guide and apply the corresponding setting data using the reset command. Cannot transmit/
receive data. Cannot search this product from the Wi-Fi terminal. Cannot log in from the console. The setting is not applied to this product. Cannot establish the communi-
cation. Others Panasonic System Networks Co.,Ltd 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan Panasonic System Networks Co., Ltd. 2015 61 xxxx-xxxx
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2016-01-04 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
2 | 5745 ~ 5825 | NII - Unlicensed National Information Infrastructure TX |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2016-01-04
|
||||
1 2 | Applicant's complete, legal business name |
Alpha Networks Inc.
|
||||
1 2 | FCC Registration Number (FRN) |
0010111144
|
||||
1 2 | Physical Address |
No.8, Li-shing 7th Rd.
|
||||
1 2 |
Hsinchu, N/A 300
|
|||||
1 2 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
t******@timcoengr.com
|
||||
1 2 |
T******@TIMCOENGR.COM
|
|||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
RRK
|
||||
1 2 | Equipment Product Code |
EA-7HW02AP1
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
K****** T******
|
||||
1 2 | Title |
Senior Manager
|
||||
1 2 | Telephone Number |
886-3******** Extension:
|
||||
1 2 | Fax Number |
886-3********
|
||||
1 2 |
k******@alphanetworks.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | NII - Unlicensed National Information Infrastructure TX | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless Access Point | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Power listed is maximum combined output power conducted. This device is restricted to indoor use only. Device operates with specific antennas in MIMO configurations as described in this filing. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not transmit simultaneously with any other antenna or transmitter. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device has 20 and 40 MHz bandwidth modes. | ||||
1 2 | Power listed is maximum combined output power conducted. This device is restricted to indoor use only. Device operates with specific antennas in MIMO configurations as described in this filing. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not transmit simultaneously with any other antenna or transmitter. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device has 20, 40, and 80 MHz bandwidth modes. | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Sporton International Inc.
|
||||
1 2 | Name |
A**** C******
|
||||
1 2 | Telephone Number |
886-3******** Extension:
|
||||
1 2 | Fax Number |
886-3********
|
||||
1 2 |
a******@sporton.com.tw
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC MO | 2412.00000000 | 2462.00000000 | 0.6050000 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15E | 38 CC MO | 5180 | 5240 | 0.573 | |||||||||||||||||||||||||||||||||||
2 | 2 | 15E | 38 CC MO | 5745 | 5825 | 0.562 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC