RRC065A User Manual 1.) Into Duplication Mode:
Make sure SW is on UP position. Press and hold all buttons on RRC065A, blue LED flashing 3 times shortly and 3 seconds later will light on still, now please releasing buttons. It Had into Duplication Mode now. 2.) Duplicating Code:
2-1. Please be sure RRC065A SW has to be on up position RRC065A button still, Blue LED means that in real Duplication 2-2. Releasing all buttons, and down position. 2-3. Please take original remote close to RRC065A right side to RRC065A red indicator LED had in Duplication Mode. then press any one of will keeping flashing.(It situation) please push SW to the and press button still also, find and searching till indicating more brighter, It means to the best duplicating position. then press desire button on RRC065A blue LED will flashing once (It means done), what if blue LED keeping flashing or not light off.(It means fail), please go back procedure 2-2. 2-4. Push SW1 up. 3.) Finishing Duplicating:
3-1. press all RRC065A together till blue LED flashing once, it means all Done and can be used. 3-2. What if duplication & set up fail,(Can not remote by RRC065A ),please repeat procedure 1.) 2.) and 3.) once again. Normally press any RRC065A button, it emits including 4 type Frequency (390MHz /
318MHz / 310MHz / 300MHz) Main receiver will operate in 5 seconds, if you need to re-emitting signal by RRC065A , Please releasing all buttons after blue LED lights off and repress once again. 1.) Following same way with RRC065A Duplication Mode, Duplicating Genies GENIES Garage Door operation Remote unit code into RRC065A. 2.) Please Following Genies Original User Manual, and learning RRC065A as new group for setting up. Allremote Wireless Technology, 2006/12/20 1 4.) Every single Genies Garage Main receiver only acceptance 2 pcs RRC065A Maximum to learn into on each different remote button. For Example, When you learn into first RRC065A on button A, The second RRC065A must on button B. GENIES Main Receiver Learning Mode. Press once learning button of Main receiver, The LED indicator will keeping flashing, then press RRC065A face toward to main receiver. When Main receiver catch the signal the LED is becoming light on still. Now, Please press once again on RRC065A same button, when main receivers LED indicator is lighted off, It meant Learning is done, be working immediately on NEW remote unit.
(Note: In certain instances, this procedure may cause the Genie Intellicod /GMI-3BL Remote to "unlearn" the programming. Make sure to check the Genie Intellicode /GMI -3BL Remote when finished, and re-program according to the manufacturer's Instructions if necessary. Then check both units to make sure that they operate the garage door opener properly.) COMPATIBILITY CHART:
REPLACEMENT BRAND Models TRANSMISSION
(APPROX. YEAR) FREQUENCY Chamberlain 750CB, 753CB,756CB,850CB,853CB,856CB 390 MHz Genie GIT-1 ,GIT-2,GIT-3,GMI-3BL,GMIC-2BL 390 MHz GPT90-1,GPT90-3,MAT90,GT912,GCT-3 , GT-31 Lift Master 33LM,51LM,53LM,54LM ,61LM,62LM,63LM,64LM, 390MHz 81LM, 82LM, 83LM, TC-1, TC-2, TC-4. Sears / Craftsman 1984 ~ 1997 390 MHz Linear/Moor-O-Matic/ DTC,LB,DT2A,DT4,DT3+1,DTK 310 MHz Delta 3 system Digic-code DC5012,DC5032,DC42,DC5062,DC5072 310 MHz Stanley 1976 ~ 1997 310 MHz Multi-Code 3060,3070,3083, 3089, 4120,4140 300 MHz Digic-code 5030,5040,5060,5070 300 MHz Allremote Wireless Technology, 2006/12/20 2 FCC approved, ID No. OAVRRC065A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Allremote Wireless Technology, 2006/12/20 3