FCC ID: 2ASK3CT-6342T ASC-2400 HD Video drone

 

FCC Part 15 C Notice

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

•

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or experienced radio/TV technician for help.

Increase the separation between the equipment and receiver.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

FCC RF exposure statements （for the drone only）

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 20 centimeters between the

radiator and your body or nearby persons.

ASC-2400

HD VIDEO DRONE

ON BOARD

HD CAMERA

ON BOARD

HD VIDEO

1280 x 720 pixels

25 frames per second

Conforms to safety requirements of FCC.

Ascend Aeronautics™ is the registered trademark of AMAX Industrial Group LTD.

AMAX Group USA Address: 12645 Memorial Dr Suite F1 #388 Houston, TX 77024

© 2021 All Rights Reserved. visit us at www.amaxbrands.com

INSTRUCTION BOOKLET

WARNING: Never leave your drone charging unattended for extended periods of

time. Always disconnect the battery from charger immediately after the battery

is fully charged. Please refer to the enclosed safety instructions.

PACKAGE CONTAINS:

Distributed by:

Costco Wholesale Corporation

P.O. Box 34535

Seattle, WA 98124-1535

USA

1-800-774-2678

www.costco.com

15

WARNING!

CHOKING HAZARD - Small parts.

Not suitable for children under 3 years.

Made in China

CT-6333

C009-USA-V1.0

ASC-2400

2.4G Wireless

Controller

Spare Parts

USB Charger

Phone Holder

Battery

Set of 4 AAA

Batteries

for Controller

Instruction

Manual

Colors and styles may vary slightly from photos

TABLE OF CONTENTS

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Remote Control Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Charging The ASC-2400 Li-Poly Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installing The ASC-2400 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

How To Expand And Fold Your ASC-2400 Arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

ASC-2400 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Control Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Flight Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Syncing Your ASC-2400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Now You Are Ready To Fly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Recognizing The Front & Rear Of The ASC-2400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Starting & Stopping The Rotors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Auto Start / Auto Land . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Manual Start/Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Speed Select Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Flight Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Flight Practice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Adjusting The Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Calibrating The ASC-2400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

How To Perform 360º Stunt Rolls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing Your Phone Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Camera Video And Photo Streaming Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Troubleshooting Your ASC-2400. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Replacing The Propeller Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Battery Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Care And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Limited 90-Day Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

FEATURES

• Streams video and still Images directly to your mobile device

• Push button Auto Start, Hover, and Auto Land technology

• Built-in 6 Axis Gyro + Altitude Sensors for incredibly stable flight

• High Efficiency Li-poly battery extends drone flight time*

• "Go-Anywhere" Folding Frame design for easy transportation

REMOTE CONTROL BATTERY INSTALLATION

1. Unscrew and remove the battery cover from the back of the controller.

2. Install 4 AAA alkaline batteries into the controller as shown in diagram A.

Replace the battery cover and secure it.

3. Turn over the controller front side up and press the power button.

If you hear two beeps and the power indicator light turns on, you

have installed your batteries correctly.

CHARGING THE ASC-2400 LI-POLY BATTERY

1. Insert the USB charger into the battery charging socket (see diagram B).

2. Connect the USB end of the cable to your computer’s USB port or a USB wall charger (see diagram C).

3. A red LED indicator light will illuminate while charging and then turn off when charging is complete.

4. Average charging time is approximately 130-150 minutes (via 5.0V 2A USB wall charger). A fully

4×1.5 volt “AAA” Alkaline Batteries (included)

charged ASC-2400 can fly for 15-18 minutes depending on environment and user input.

IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!

Li-Poly Battery

B.

LED indicator

INSTALLING THE ASC-2400 BATTERY

Carefully Push the fully charged battery into the ASC-2400 battery

compartment all the way in until it stops and is flush with back of

the drone (see diagram D).

NOTE: The battery only fits one way into the battery compartment. Never force it.

HOW TO EXPAND AND FOLD YOUR ASC-2400 ARMS

Before flying your ASC-2400, you need to expand the foldable arms out.

1. Make sure the drone power is turned off.

2. Holding the folded ASC-2400 drone in the palm of your hand

(see diagram E) proceed to open the arms by starting with the

Front Arms (Upper Arms) and then Rear Arms (Lower Arms)

3. Make sure the arms are fully extended and locked into place

(see diagram F). Note you will feel some additional pressure

indicating the arm is properly locked into place.

4. When folding in the arms simply reverse steps 1-3 above.

NOTE: Never use hard force when opening and closing the ASC-2400 Arms

A.

C.

D

Thank you for purchasing the ASC-2400 Drone. Please read this instruction booklet as it contains valuable

information on how to properly fly and care your ASC-2400.

1

E

F

2

ASC-2400 DIAGRAM

Camera

WARNING

DO NOT FLY YOUR ASC-2400 IN FOUL WEATHER!

Propeller

Power Button

CONTROLLER DIAGRAM

Emergency Stop

Speed Setting Button

ON/OFF &

Power Indicator

360˚ Stunt Rolls Button

Throttle/Yaw

Turning Left Trim

Turning Right Trim

3

Forward

Trim

AUTO Start/ AUTO Land

Backward

Trim

Direction Controls

Press to take a photo

Press down & hold to begin

video recording

Banking Right Trim

Banking Left Trim

Power Button

FLIGHT PREPARATION

• Verify that there are 4 “AAA” batteries inside the remote control unit and the ASC-2400 Li-poly battery

has been fully charged.

• Make sure to be in a large open space preferably a field or a park with an open radius of at least 400 feet.

• Make sure to start your drone on a clean flat level surface before take-off.

• IMPORTANT! Until you have experience in flying your ASC-2400, it is not advised to use in any rate of

wind. Pick a day with zero wind or extremely light wind condition when learning how to fly.

SYNCING YOUR ASC-2400

Important! When syncing your ASC-2400 with the controller always make sure that the drone is on

a flat level surface and that your digital trim settings are in the center position.

1. Before starting, make sure that the power on your controller is off and the battery is removed from the

ASC-2400.

2. Insert the battery into the ASC-2400 and set it down on a flat level surface. Press down the power button

and hold for a few seconds (see diagram G). The red LED lights on the drone should begin to flash rapidly

first and then flash slow.

3. Quickly turn ON the remote and you will notice that the top red LED light on the face of the controller

is flashing.

4. Push the throttle stick all the way up until it stops and then pull it back all the way down to the bottom

(see diagram below). When pushing the stick up or pulling the stick down you should hear a

high-pitched beep both ways. If the indicator lights on the drone and controller stop flashing and stay

solid, you have successfully synced your ASC-2400 and are ready to fly. If you are not able to Sync, please

repeat steps 1-4 again.

• TIP 1: Try not to leave too much time between turning your drone on and turning

on the controller, or your syncing window will time-out.

• TIP 2: Syncing your drone indoors or in the shade will make it easier to see the LED

light indicators.

G

Move the control stick all the way up

and all the way down, you should

hear two beeps.

The flashing red LED light will

become solid when you are synced.

4

FLIGHT CONTROL

Below is a list of basic flight inputs/functions that will help you learn to fly the ASC-2400. While learning

to fly your drone it’s best to start in a large space with the drone facing away from you until you get used

to the basic controls. As you master flying your ASC-2400 you can move to more advanced maneuvering

techniques. Practice makes perfect!

NOW YOU ARE READY TO FLY!

If you have successfully synced your ASC-2400 to your controller as explained on page 4 you are now ready to

fly. Before beginning to fly your drone you should familiarize yourself with how to start and stop the rotors,

how to use your auto land feature and how the controls work. Please carefully read and familiarize yourself

with the various control features explained in the instruction manual. Once again as a beginner pilot you

should learn how to control your drone in a large open field or park on a day with zero or very light wind. Do

not try to fly your ASC-2400 too high until you become a more experience pilot.

RECOGNIZING THE FRONT & REAR OF THE ASC-2400

Even though the ASC-2400 has four rotors there is still a front or "forward"

facing direction and "rear" or backwards facing direction. The front

forward facing direction of the ASC-2400 is the side with a camera. The

rear and backward facing direction of the drone is the side with a red light

(see diagram H).

STARTING/STOPPING THE ROTORS

Note: You can start and stop your ASC-2400 Manually or Automatically.

Please follow one of the steps below to operate accordingly. Make sure

you have properly synced the ASC-2400 drone which is indicated by a

solid red light on both the controller and the drone.

FRONT

REAR

H

AUTO START/AUTO LAND

The ASC-2400 has an auto start/auto land feature which allows you to start and land automatically. Simply press the

auto START/LAND button on the face of the controller (see diagram I) and your ASC-2400 will begin taking off or land

(if your already in the air).

NOTE: You can still control the drone’s direction while auto ascending or auto-landing if necessary to avoid obstacles.

I

MANUAL START/STOP

• To Manually start the rotors simply move the two control sticks simultaneously down to the inside or outside corners

(see diagram J ), hold until the rotors start spinning. Now release both sticks to the neutral position and push the

throttle up to take off.

• To manually stop the rotors you can: a) simply land on the ground and the Rotors will automatically stop in ten seconds

or less. b)You can immediately stop the rotors by moving the two control sticks simultaneously down and to the inside

or outside or outside bottom corners (see diagram J) or c) EMERGENCY STOP: you can make an emergency stop by

depressing both the SPEED button and the STUNT button simultaneously (see diagram K).

L

L1

L2

L3

Move the left throttle stick up to increase the

propeller speed and the ASC-2400 will ascend.

Move the left throttle stick down to decrease the

propeller speed and the ASC-2400 will descend

(see diagram L).

While in the air, move the left throttle stick

directly left and the ASC-2400 will rotate

horizontally left (counter clockwise).

Move the left throttle stick directly right and the

ASC-2400 will rotate horizontally right

(see diagram L1).

While in the air, move the right direction control

stick forward and the ASC-2400 will move

forward.

Move the right direction control stick backwards

and the ASC-2400 will move backward

(see diagram L2).

While in the air, move the right direction control stick

to the left and the ASC-2400 will bank/sweep to the

left.

Move the right direction control stick to the right

and the ASC-2400 will bank/sweep to the right

(see diagram L3).

FLIGHT PRACTICE

To master flying your ASC-2400 drone try practicing the exercises shown below, start with simple vertical

takeoffs, landings, and left/right turning and rotating. Once those are mastered move on to square and

cross maneuvers. Good luck and have fun!

J

K

SPEED SELECT BUTTON

The ASC-2400 has 3 speed settings; 1 (SLOW), 2 (MEDIUM) and 3 (HIGH). The Default setting when you first

turn on your ASC-2400 is the 1 (SLOW) speed mode. To increase the speed simply press the speed setting

button on the top of the remote (see remote diagram on pg 3) you will hear beeping sounds letting you

know what speed setting you are on. Speed settings can be set before flight or during the flight.

5

Fixed-Point Landing

Square Pattern Maneuver

Cross Pattern Maneuver

6

ADJUSTING THE TRIM

NOTE: The ASC-2400 is already properly trimmed and calibrated right out of the box and should not require

any trim adjustments before flying. Some more experienced pilots may want to adjust trim settings for

their style of flying. After several crashes you may need to adjust trim settings for the ASC-2400 to be more

balanced.

M

N

Forward/Backward Trim

• If your ASC-2400 drifts forwards or backwards while

in the air, counter the movement by using your

forward /backward trim buttons (see diagram M).

Bank Right/Left Trim

• If your ASC-2400 drifts to the left or right while in the

air, counter the movement by using your left / right

trim buttons (see diagram N).

Spinning/Rotating Trim

• If your ASC-2400 spins either left or right while in the

air, counter the rotation by using your left and right

rotational trim buttons (see diagram O).

O

CALIBRATING THE ASC-2400

NOTE: Your ASC-2400 comes pre-calibrated out of the box so you are ready to fly.

After several crashes and shocks to your gyro sensors, you may notice that your drone is drifting and cannot

hold its center position while hovering as well as it used to.

This most likely means that you need to recalibrate your ASC-2400. Please follow the simple instructions

below.

1. Place the ASC-2400 on a very flat level surface.

2. Make sure the ASC-2400 is turned on and that the controller is synced (refer to syncing pg 4). Do not start

the blades! Instead move both the throttle and control stick down and to the right hand bottom corner

(see diagram P). If successful you will see the lights on the drone rapidly flash and stop. Once the lights

stop flashing you have completed your calibration and are ready to fly again!

TROUBLE SHOOTING: If you do not see the lights flash, remove the battery from the drone then turn off your

controller and start over. Always make sure to put your battery in before turning on your controller. Push the

left throttle stick all the way up and then down touching the top and bottom of the controller. When you

hear the beep the ASC-2400 is re-synced to the controller and you are ready to calibrate.

P

HOW TO PERFORM 360º STUNT ROLLS

Performing 360º stunt rolls with the ASC-2400 is as easy as 1-2-3:

1. Hover the ASC-2400 in a still position making sure that you have at least 6 feet of clearance above and

below the drone. Set the speed settings to mode 2 or 3 (the ASC-2400 cannot perform the stunt roll in

speed setting 1).

2. First press the 360 stunt button on the right top side of the controller and you will enter the “stunt roll

mode” which is indicated by a rapid beeping sound (see diagram Q).

3. Next, using the right control stick, push directly to the right for a “right side roll” or directly to the left for

a “left side roll” (see diagram R). Remember to always use caution when performing stunts.

360˚Stunt Roll Button

EMERGENCY STOP: press the “speed setting button” and “stunt button” simultaneously to stop the

drone blade from spinning. Use this anytime you lose control of your drone.

NOTE: When using the trim buttons you will beeping sounds. A short “beep” indicates “one trim

position movement” A long Beep indicates that you have reached the center trim position. When

there are no longer beeps, you have reached the maximum trim position for that particular

setting. If this happens and your Drone is still not stable, we suggest you re-sync your drone and

re-calibrate on very flat surface (see recalibrating your drone on next page)

Q

R

7

NOTE: To exit the stunt roll mode without flipping simply press the stunt button again and the

beeping sound will stop indicating you have exited “stunt mode”

8

INSTALLING YOUR PHONE HOLDER

Installing your phone holder is required to use your ASC-2400 drone’s camera. To install your phone holder,

turn your controller around to the back side with the battery compartment facing you and start by clicking

in the top “two teeth” into the two holes on the top of the controller and then proceed to click in the

bottom (see diagram S).

To remove, pull from the bottom first.

S

b

a

finished

installation

CAMERA VIDEO AND PHOTO STREAMING SETUP

Your ASC-2400 comes equipped with an on-board digital camera that takes both video and still photographs and

streams them to your mobile device.

WHAT YOU WILL NEED TO GET STARTED USING YOUR CAMERA

1. One Apple or Android Smart phone* (Phone not included).

2. The ASC-2400 App successfully downloaded and installed on your mobile device.

Note instructions on using the App are in the application tutorial

3.To Download the ASC-2400 App, scan the appropriate QR code below which will link to the App on either

the Android Play Store or Apple Store. If you are not able to scan the QR code, manually enter the web

address located under the appropriate QR code for your phone.

4. After the ASC-2400 App is installed, it should create an icon on your screen (see icon below). Click the

icon to run the App and make sure that it has installed correctly on your device. If not, please delete and

repeat the process again.

5. Follow the “TUTORIAL” for instructions on connecting/pairing your ASC-2400 drone to the App and using

the App for recording film and still photos.

ICON

2000 Series

Apple® iOS

http://netopsun.com/asc_2000_series_apple

Android OS

http://netopsun.com/asc_2000_series_google

* Apple® devices require the use of iOS 10.0 or higher.

ANDROID™ devices require the use of OS 4.2.2 or higher.

If you’re still encountering difficulties downloading the ASC-2400 App, please contact our

customer service department at www.amaxbrands.com or 1-866-360-1510

9

10

TROUBLESHOOTING YOUR ASC-2400

PROBLEM

POSSIBLE CAUSE

POSSIBLE SOLUTION

No Power

1. Power switched off

2. Polarity is reversed

3. Batteries may be low or in need of charging

1. Press the ON/OFF switch to ON

2. Make sure all batteries are installed

correctly (see diagram A)

3. Replace batteries

Drone Not

Responding

1. Remote is switched off

2. Battery power in remote is too weak

3. The remote is not properly synced

4. Out of control range

1. ASC-2400 the ON/OFF switch to ON

2. Replace remote batteries

3. Re-sync the remote

4. Do not fly beyond 400 feet

Drone Won’t

lift off

1. Rotor speed too slow

2. Drone not fully charged

3. Obstruction of rotors

1. Push throttle lever forward

2. Recharge your ASC-2400

3. Check rotors for hair or other obstructions

Drone Spins, can

not be trimmed

Rotor deformation

Motor not functioning

Drone did not calibrate properly

Replace the damaged rotor (You may

need to consult with a customer service

personnel)

Restart the drone and controller, properly

calibrate it on a flat level surface

Drone vibrates too much

Check the propeller deformation

Drone Tilt to one

direction

Altitude Hold

height is not

stable, the drone

continues to

move up and

down without

locking into

position

REPLACING THE PROPELLER BLADES

Your ASC-2400’s propeller system is a precision instrument that may need repair or replacement from time to

time for optimal flight function. Crash landing at high-speed may cause damage to your ASC-2400 propellers.

1. The ASC-2400 has four sets blades, two sets of blades with indication letters A & B on front, and two sets

blades with indication letters B & A on the rear (see the diagram T).

2. When replacing the propeller blades, make sure to match the indication markings/letters on the blades.

3. Unscrew and take off the damaged blade.

4. Replace with new correct blade.

Blade Front Left = A

Blade Front Right = B

Blade Back Left = B

Blade Back Right = A

Front

A

B

B

A

T

11

12

ASC-2400 WARNING:

The ASC-2400 is designed for OUTDOOR USE ONLY. The ASC-2400 blades revolve at high speeds and can

cause damage to the user, spectators and animals. Stand away from the ASC-2400 to reduce the risk of

getting into the flight path. Warn spectators that you will be flying your ASC-2400 so that they are aware

of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened

to the ASC-2400.

WARNING!

• Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.

• Keep hands, hair and loose clothing away from the propeller when the power ASC-2400 is turned to the

ON position.

• Turn off the transmitter and ASC-2400 when not in use.

• The included charger is built specifically for the ASC-2400 Li-Poly battery. Do not use it to charge any

other battery.

• New alkaline batteries are recommended for maximum performance.

• Parental supervision recommended when flying ASC-2400 .

BATTERY WARNINGS

RECHARGEABLE BATTERY:

This ASC-2400 uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery

properly according to local disposal requirements.

CONTROLLER BATTERIES:

Remote control requires 4 “AAA” batteries (included).

Please read the important battery safety warning below.

• Always replace the whole set of batteries at one time.

• Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride).

• Do not mix old and new batteries.

• Non-rechargeable batteries are not to be recharged.

• Rechargeable batteries are to be removed from the item before being charged (if removable).

• Rechargeable batteries are only to be charged under adult supervision.

• Exhausted batteries should be removed immediately and must be recycled or disposed of properly

according to state or local government ordinances and regulations.

• The supply terminals are not to be short-circuited.

• Only batteries of the same or equivalent type as recommended are to be used.

• Batteries are to be inserted with the correct polarity (see inside booklet for diagram).

• Do not dispose batteries in a fire - batteries may leak or explode.

• This product is only to be connected to equipment bearing either of the following symbols: or

III

CARE AND MAINTENANCE

• Always remove the batteries from the wireless remote control when it is not being used for an extended

period of time.

• To clean, gently wipe the remote control and ASC-2400 with a clean damp cloth.

• Keep the product away from direct heat or sunlight.

• Do not submerge the product into water. This can damage the unit beyond repair.

• Parental guidance recommended when installing or replacing the batteries.

Limited 90-Day Warranty

NORTH AMERICA

AMAX Group USA warrants to the original consumer that this product is free from any electrical or

mechanical defects for a period of 90 DAYS from the date of purchase. If any such defect is

discovered within the warranty period, AMAX Group USA will repair or replace the unit free of charge

upon receipt of the unit, shipped postage prepaid and insured to our warranty center ALONG WITH

THE ORIGINAL RECEIPT evidencing that the product was purchased from an approved AMAX retail

partner and that the product is still within the 90 day warranty period. The warranty covers normal

consumer use and does not cover damage that occurs in shipment or failure that results from

alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use

or unreasonable use of the unit. Removal of any parts/components voids all warranties. This warranty

does not cover cost of repairs made or attempted outside by third-party individuals or companies.

Any applicable implied warranties, including warranties of merchantability and fitness, are hereby

limited to 90 DAYS from the date of purchase. Consequential or incidental damages resulting from a

breach of any applicable express or implied warranties are hereby excluded. Some states do not

allow limitations on the duration of implied warranties and do not allow exclusion of incidental or

consequential damages, so the above limitations and exclusions in these instances may not apply.

REPAIR/REPLACE PRODUCT

If your product begins to malfunction or stop working, immediately contact our warranty center

(contact details listed below). If it is determined that a return is necessary, our warranty department

will issue you an RMA number/form and an address to the nearest return center for shipping the

product to us. When honoring the warranty, AMAX reserves the right to either repair, replace or

refund the product.

IMPORTANT NOTICE:

We will reject and return to sender returns that are not accompanied by an AMAX issued RMA form

and RMA number so make sure to contact our warranty center before attempting to return your

product!

PREPARATION FOR SHIPPING YOUR PRODUCT:

Please repack your product in a durable box, preferably in the original carton, and send it prepaid,

and adequately insured. Include the RMA form that was issued by our warranty department along

with your daytime telephone number and email address inside the shipping carton. If your warranty

has expired and you still require service please contact our customer care team For further

information please send all inquiries to: customercare@amaxbrands.com

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major failure and for compensation for any other

reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced

if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

IMPORTANT NOTICE!

DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK

WITHOUT FIRST CONTACTING OUR WARRANTY

DEPARTMENT AT:

www.amaxbrands.com

Email: care@amaxglobal.com

Phone 1-866-360-1510

13

14



 

 

 

 

 

 

 

 

 

 

Amax Industrial Group China Co. Limited 852.3962.5160 Model Number: CT-6333 F08B01D05/2021 Shenzhen, China FCC ID: 2ASK3CT-6342T This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 10mm 14.4mm 9.4mm 39.3mm

 

 

AMAX INDUSTRIAL GROUP CHINA CO., LTD

Date:2021/6/23

Federal Communications Commission

7435 Oakland Mills Road

Columbia MD 21046

To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all

manners relating to application for equipment authorization, including signing of all documents

relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our

behalf shall have the same effect as acts of our own.

I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that

includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.

853(a).

In authorizing UL Verification Services Inc. as our representative, we still recognize that we are

responsible to:

a) comply with the relevant provisions of the certification program;

b)

c)

d)

e)

f)

make all necessary arrangements for the conduct of the evaluation, including

provision for examining documentation and access to all areas, records (including

internal audit reports) and personnel for the purposes of evaluation (e.g. testing,

inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which

certification has been granted;

do not use our product certification in such a manner as to bring the Certification

Division into disrepute and not make any statement regarding our product

certification which the Certification Division may consider misleading or

unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising

matter that contains any reference thereto and return any certification documents

as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity

with specified standards;

g)

h)

i)

j)

endeavor to ensure that no certificate or report nor any part thereof is used in a

misleading manner;

ensure that any reference to our product certification in communication media

such as documents, brochures or advertising, complies with the requirements of

the Certification Division;

keep a record of all complaints made known to us relating to the product’s

compliance with requirements of the relevant standard and to make these records

available to the when requested;

take appropriate action with respect to such complaints and any deficiencies

found in products or services that affect compliance with the requirements for

certification;

k)

document the actions taken.

This authorization is valid until further written notice from the applicant.

Sincerely Yours,

Signed by:

Company Name: AMAX INDUSTRIAL GROUP CHINA CO., LTD

Contact Name: Nancy Chen

Title of Person：QA Manager

Address: NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON

HongKong China



 

 

AMAX INDUSTRIAL GROUP CHINA CO.,LTD.

2ASK3CT-6342T

Request for Confidentiality

Federal Communications Commission

7435 Oakland Mills Road

Columbia MD 21046

Subject:

FCC ID:

To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§

0.457, 0.459), we are requesting the Commission to withhold the following attachments as

confidential document from public disclosure indefinitely.

Schematic Diagram

Block Diagram

Theory of Operation

Above mentioned document contains detailed system and equipment description are considered

as proprietary information in operation of the equipment. The public disclosure of above

documents might be harmful to our company and would give competitor an unfair advantage in

the market.

It is our understanding that all measurement test reports, FCC ID label format and correspondent

during certification review process cannot be granted as confidential documents and those

information will be available for public review once the grant of equipment authorization is

issued.

Best Regards

Company Name: AMAX INDUSTRIAL GROUP CHINA CO., LTD

Contact Name: Ms Nancy Chen

Title of Person：QA Manager

Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI

STREET MONGKOK KOWLOON HONG KONG

Date: 07/05/2021



 

 

AMAX INDUSTRIAL GROUP CHINA CO.,LTD

Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI

STREET MONGKOK KOWLOON HONG KONG

Confirmation Letter

We, AMAX INDUSTRIAL GROUP CHINA CO.,LTD

The product: ASC-2400 HD Video drone

And model No.: CT-6333

FCC ID: 2ASK3CT-6342T

OA-6288, 1540563, CT-6342, CT-6343，NV-6309 have the same technical construction

including circuit diagram, PCB Layout, components and component layout, all electrical

construction and mechanical construction with C T - 6 3 3 3.The difference lies only the

model number. All these changes do not degrade the unwanted emissions of the certified

product.

Contact Name: Ms Nancy Chen

Title of Person: QA Manager

Date： 07/05/2021