FCC ID: 2ASK3VL-6228T Blaze Buggy

STEERING WHEEL TRIM ADJUSTMENT If the Truck can not go forward straightly you may need adjust the steering wheel trim on the bottom of the truck from time to time until the truck can go forward straight. (see diagram F) F WARNING DO NOT USE TRUCK IN INCLIMATE WEATHER!

TROUBLESHOOTING Before sending your truck in for repair, please check for a solution below. Problem Possible Cause(s) Solution Truck will not move. Weak batteries; no batteries Truck does not respond properly to remote control. Truck and remote not synced properly Another RC truck may be transmitting on the same radio frequency Truck loses connection to remote control. Using truck in a small enclosed area Using truck indoors Low batteries in transmitter or vehicle Install new batteries in remote control and recharge the truck battery. Refer to sync section and re-sync your truck and remote. Move to a new location where no other RC trucks are present. Move outdoors to a large open area. Install new batteries in remote control or recharge your truck. Truck battery has fully charged, but slower than normal. Driving truck for too long at high speeds, causing motor to overheat Turn truck off for 10-15 minutes. For further information please send all inquiries to customerservice@amaxbrands.com BATTERY WARNING:

Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (nickel-cadmium). Do not mix old and new batteries. Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from the unit before being charged (if removable). Rechargeable batteries are only to be charged under adult supervision (if removable). Exhausted batteries are to be removed. The supply terminals are not to be short-circuited. Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity. LITHIUM BATTERY STATEMENT:

Battery may explode or leak chemicals if opened, exposed to fire or high temperature, installed backwards, or mixed with other battery types. SAFETY WARNINGS!

Improper use of batteries may lead to overheating, breakage or leaking.

- Do not mix old and new batteries.

- Do not mix different battery brands.

- Install batteries with correct polarity. The flat side (negative terminal) of the battery should rest against the spring.

- Remove dead batteries immediately.

- Avoid liquids, which can short circuit the batteries.

- The truck or remote will become unresponsive when batteries are low, at which point you should replace all batteries with new ones.

- Remove the batteries if you will not use the truck for a long time. Avoid using near furniture or glass to prevent damage to these objects. Do not play on roads. Do not play in crowded areas to avoid injury or damage. Choose a safe location away from traffic. Do not use truck during a storm or when lightning or thunder are present. Do not use in a wet , sandy or muddy environment as truck may become damaged. Do not modify or attempt to replace the built-in original antenna on the remote or truck. Doing so will damage the Do not pull on any wires that are part of the truck. Such action may cause the wires to break and the truck to malfunction. Keep fingers, hair and clothes away from the trucks spinning tires. Failure to do so may result in physical injury. Never aim the truck at other people. Do not throw the truck or purposely hit it with any object. Store truck in a cool environment, away from high-temperature sources such as fires, stoves, radiators, etc. This truck has no user-serviceable parts. Do not attempt to modify components or circuit board. set and affect operation. FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Conforms to safety requirements of FCC. INSTRUCTION MANUAL Thank you for choosing BLAZE BUGGY. With proper care, your new BLAZE BUGGY will provide you with many hours of enjoyment. Please read this instruction manual completely before using the product for the first time, and then keep this manual in a handy place for future reference. Adult supervision is required when charging. Colors and styles may slightly vary. PACKAGE CONTENTS BLAZE BUGGY RADIO CONTROLLED HIGH SPEED VEHICLE Remote control USB charger 7.4V Li-poly battery pack 2. Install batteries into the remote control. Open the battery cover on the bottom of the remote control (see diagram E). Insert 2AA batteries into the battery compartment, matching polarity (+ and -) marked inside. Replace the battery cover. CHARGING THE BATTERY 1. Insert the white, 3-wire battery charging plug into the USB charger's socket. The charging plug and the USB charger's socket fit only one way. Dot not force them (see illustration A). 2. Connect the USB end of the cable to your computers USB port or a USB wall charger (see diagram B), The Red CHARGE indicator light turns stay to show that charging is in progress. 3. Average charging time is approximately 2.5 hours( via 5.0V 2A USB wall charger). The truck operates for approximately 40 minutes on full charge. 4. The red charging indicator turns off when the battery is fully charged. Note: Periodically examine the charger for external damage. External damage to the charger may result in the risk of fire, electric shock, or injury to persons. Never use a damaged adapter. Batteries Included (2xAA) E TRUCK DIAGRAM (Bottom View) Steering Wheel Trim Red Charging Light Battery Compartment ON/OFF Switch A B SET-UP 1. Install the included Li-poly battery into the truck. a) Remove the battery compartment cover on the bottom side of the truck (see diagram C). b) Connect the rechargeable Li-poly battery cord directly to the BLAZE BUGGYs power cord socket, make sure the connection is secure. The Li-poly battery connecting plug and the BLAZE BUGGYs socket fit in only one direction never force a connection ( See diagram D). c) Carefully replace the battery compartment. REMOTE DIAGRAM Power Indicator ON/ OFF Switch Steering Throttle Battery Compartment C D SYNCING YOUR BLAZE BUGGY Your BLAZE BUGGY features an automatic 2.4G channel selection system that allows up to 8 people to race side by side in the same wireless range. For One Player:

1. Before starting, make sure that the power on both your remote control and truck are in the OFF position. Make sure that there are no other 2.4G devices in the area. 2. Turn ON the truck and set it down on a flat surface. 3. Turn ON the remote control. When the remote control's power indicator flashes, pull the throttle all the way down and the power indicator lights continuously. This indicates that your truck and remote control have successfully synced. If pairing fails, repeat steps 1-3. For Multiple Players:

1. Before starting, make sure that the power on all trucks and controllers are in the OFF position. Make sure that there are no other 2.4G devices in the area. 2. Each person will have to sync a truck individually at a different time to avoid interference. Follow steps 1 to 3 above, making sure to keep away from other people while also making sure that no one else is syncing at the same time. 3. After syncing, leave the truck ON until all players have synced their trucks. 4. If there is interference, all players must turn off their controllers and trucks and restart the syncing process. OPERATION THIS IS A HIGH-SPEED OUTDOOR RC TRUCK. DO NOT PLAY INSIDE YOUR HOME OR OTHER SMALL ENCLOSED AREAS. 1. Turn your truck on:

Pick up your truck and turn it over to make sure the battery is properly installed and the battery compartment door is properly closed and locked. Sync your truck and remote control and set the truck on the ground. 2. Driving your truck:

Pull the throttle halfway to drive forward at low speed. Pull the throttle fully to drive at high speed. Push the throttle forward to make truck move in reverse. Turn the steering control to the counterclockwise to turn the truck left. Turn steering to the clockwise to turn the truck right. To break or quickly stop simply pull or push the throttle in the opposite direction.

FCC ID: 2ASK3VL-6228T This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.1MM 6.4MM 27.2MM 56MM

Date: 2021-2-10 Confidentiality Request regarding application for FCC ID: 2ASK3VL-6228T To:

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: AMAX INDUSTRIAL GROUP CHINA CO., LTD Regarding:

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby requests confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Print Name: Nancy Chen Title: Manager Signature:

On behalf of Company: AMAX INDUSTRIAL GROUP CHINA CO., LTD Telephone: 13422877086 E-mail: nancy@groupchina.com

a) b) c) d) e) f) g) SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name AMAX INDUSTRIAL GROUP CHINA CO., LTD OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG CHINA Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name Nancy Chen 2ASK3 2ASK3VL-6228T nancy@groupchina.com 13422877086 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: 2021-2-20 Print Name:

Title:

Nancy Chen Manager Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Applicant Declaration Rev:0.0

AMAX INDUSTRIAL GROUP CHINA CO., LTD Date: 2021-2-20 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2ASK3VL-6228T To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with AMAX INDUSTRIAL GROUP CHINA CO., LTD This authorization is valid until further written notice from the applicant. Print Name: Nancy Chen Title: Manager Signature:

On behalf of Company: AMAX INDUSTRIAL GROUP CHINA CO., LTD Telephone: 13422877086 E-mail: nancy@groupchina.com