FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
connected.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This product is manufactured by AMAX Group 12645 Memorial Drive Suite F1 #388 Houston, TX 77024 Propel and Propel RC are the licensed trademarks of Rooftop Group LTD Singapore. 2018 All rights reserved. Visit us at www.propelrc.com NAVIGATOR is the property of Eastern Design Group, USA. 2017 All rights reserved. WARNING!
CHOKING HAZARD - Small parts. Not suitable for children under 3 years. Conforms to safety requirements of FCC. HIGH PERFORMANCE STUNT DRONE INSTRUCTION BOOKLET WARNING: Never leave product charging unattended for extended periods of time. Always disconnect STUNT DRONE from charger immediately after the STUNT DRONE is fully charged. Please refer to enclosed safety instructions. PACKAGE CONTAINS:
A B B A 14 HIGH PERFORMANCE STUNT DRONE 2.4G Wireless Controller Spare Parts Instruction Booklet Made in China V 1.0 US Colors and styles may vary slightly. TABLE OF CONTENTS Features. 2 Remote Battery Installation. 2 Charging The Stunt Drone. 2 Stunt Drone Diagram, Remote Diagram. Syncing Your Stunt Drone. 4 Preparing For Flight. 4 Flying Tips. 4 Recognizing the Front and Rear of the . 5
. 5
. 5
.
. Speed Setting Button . T (Training)MODE .
4 Channel Flight Control . 7
. 8 Calibrating The Stunt Drone . 9
. 9 Replacing The Propeller Blade. 1 1 Battery Warnings, Care and Maintenance. 1 2
. FCC Part 15 C Notice. 1 4 FEATURES
REMOTE CONTROL BATTERY INSTALLATION 1. Unscrew and remove the battery cover from the back of the controller. 2. Install 2 AAA alkaline batteries into the controller as shown in diagram A
4. Turn over the controller and push the power button, you will see the indicator light turn on and start flashing. Battery Compartment
(2 AAA batteries not included) A. charging socket of the Stunt Drone(see diagram B ). CHARGING THE STUNT DRONE 1. Make sure the Stunt Drones power switch is in the OFF position and plug the USB charging cord into the Caution: The USB plug fits the charging socket only in one way. Do not force it. 2. Connect the USB end of the charging cable to your computers USB port or a USB wall charger (see diagram C). Note these charging times are based on 5.0V system with 2.0A or higher USB outlet.
Note: If the red LED lights up, either the charging is complete or the USB plug is not properly connected. 4. The charging time will vary depending on the percentage of battery already charged. The average charging time is
The Low battery indication: the Stunt Drone s LED lights will begin to flash to notify you that the battery is running low. The lights will continue to flash before the Stunt Drone automatically lands.
instruction booklet as it contains valuable information on how to properly fly and care your Stunt Drone. B
plug lights up when charging is complete D C 1 2 STUNT DRONE DIAGRAM Rotor Blade Safety Guard
OFF ON The safety guard is easy to clip on and off. Simply pull the clips away from each motor mount and remove the Stunt Drone from below.
Charging Socket REMOTE DIAGRAM Speed Setting Power Indicator Stunt Roll Power Switch
Right Trim Direction Control Backward Trim Forward Trim
WARNING DO NOT FLY YOUR DRONE IN FOUL WEATHER!
SYNCING YOUR Stunt Drone Important! When syncing your Stunt Drone quadrocopter with the controller always make sure that the quadrocopter is on a flat level surface and that your digital trim settings are in the center position. This ensures that the 6 Axis gyro is properly programmed to mimic your trim settings. Your Stunt Drone utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless range with no interference. For One Person Play:
1. Before starting, make sure that your controller is OFF and the Stunt Drones battery is disconnected. Make sure that there are no other 2.4G devices in the area as well. 2. Turn ON the Stunt DroneStunt Drone should begin to flash rapidly.
throttle stick all the way up until it stops and then pull it back all the way down to the bottom. When
indicating lights on the drone and controller will stop flashing and stay solid on. Your Stunt Drone and remote should have successfully synced. Should this not happen, repeat all steps again. For Multi Person Play:
4. Before starting, make sure that the power on all Stunt Drones and Controllers are OFF. Make sure that there are no other 2.4G devices in the area as well. 5. Each person will have to sync his Stunt Drone individually at a different time to avoid interference.
After syncing a players Stunt Drone, it should be left ON until all players have synced their quadrocopters.
PREPARING FOR FLIGHT
DO NOT ATTEMPT TO FLY YOUR Stunt Drone IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM. FLYING TIPS
200 foot radius.
Wind can greatly affect the performance of the Stunt Drone. 3 4 RECOGNIZING THE FRONT AND REAR OF THE QUADROCOPTER
"forward" facing direction and "rear" or backwards facing direction.
side with two gray blades (see diagram F ). The rear orbackward
and the two black propellers (see diagram F). NOTE: The front of the Quadrocopter displays WHITE LED lights and the back of the Quadrocopter displays RED LED lights. Front B A B A UNDERSTANDING TRIM ADJUSTMENTS Rear F Forward/Backward Trim
drifts the moving stops and proper flight is maintained.
drifts backwards, push and release the FORWARD TRIM (F)button in the same manner until the problem is resolved.
Forward/ Backward Trim A B A B B A B A If flying forward... If flying backward... Forward/Backward Trim Controls Push and release to go backward Push and release to go forward Banking Left/Right Trim
the banking stops and proper flight is maintained.
manner until the problem is resolved.
Bank Bank A B A B B A B A Left/Right Banking Controls 5 Push the left button to increase left banking sensitivity Push to right button to increase right banking sensitivity NOTE: The use of the Trim buttons are accompanied with a Beep tone. A single long Beep indicates the product is center trimmed. No beeps after press indicates the product is trimmed to the maximum on a particular side. AUTOMATICALLY TAKE OFF / LAND Make sure you have properly synced The Stunt Drone .
take off.
will descend and land automatically. Tips: You also can move the two control sticks simultaneously down to the inside or outside corners, hold them till the blades start spinning. Release the control sticks and push the throttle stick slowly to take off manually. UNDERSTANDING THE ALTITUDE LOCK SENSOR The control and stability. It allows the user to ease into piloting the drone. The sensor locks in the altitude of the drone while allowing the user to adjust the directional controls without having to hold the throttle. After starting the drone, fly it upwards to a safe height. Once at a safe height, release the throttle to the neutral position. Now your Stunt Drone should be locked in the altitude and you can focus on getting used to the directional controls of the Stunt Drone. The drone always will tends to self correct and go back to the last locked height after moved up or down by outside forces. Note: The altitude sensor does have some tolerance based on atmospheric conditions and could have a slight variation in altitude. SPEED SETTING BUTTON The Stunt Drone has 4 speed settings; T(Training),1(SLOW),2(MEDIUM) and 3(HIGH). The Default setting when you first turn on your Stunt Drone is 1(SLOW). To change speed, just press and release the
sounds, one beeping sound for slow speed, two for medium speed and three for high speed. T (Training)MODE Simply press and hold the Speed Setting Button; till you heared a long beep, now you are in T Mode. T mode allows you to learn how to operate your Stunt Drone at a very slow speed. Also in T mode a minumum and maximum height limit are set to help avoid crashing into the ground or ceiling while learning. To exit T mode just short press the speed setting button again. 3/4 CHANNEL SELECT Stunt Drone channel mode (beginner) or 4 channel mode (advanced flying). The Stunt Drone default setting is 4 channel mode.
PRESS the Direction Control stick vertically down then release,
Stunt Drone now is
6 To change back to 4 Channel mode:
PRESS the Direction Control stick vertically down then release again, you will hear 4 short beeps indicating the Stunt Drone is now set to 4CH mode. 4 CHANNEL FLIGHT CONTROL
fly your Stunt Drone it is best to start with a large space until you get used to the basic controls. As you master flying your Stunt Drone you can move to more advanced maneuvering techniques. Practice makes
3 CHANNEL FLIGHT CONTROL
fly your Stunt Drone it is best to start with a large space until you get used to the basic controls. As you master flying your Stunt Drone you can move to more advanced maneuvering techniques. Practice makes
speed and the Stunt Drone will accelerate.
the speed and the Stunt Drone will descend. Move the left Throttle stick up to increase the speed and the Stunt Drone will accelerate and ascend. Move the left Throttle stick down to decrease the speed and the Stunt Drone will decelerate and descend. A B A B B A B A A B A B B A B A
Move the right directional stick RIGHT to
Move the left Throttle stick left and the Stunt
Move the left Throttle stick right and the Stunt
A B A B B A B A A B A B B A B A Move the Right Direction Stick forwards and the Stunt Drone will move forward. Move the Right Direction Stick backwards down and the Stunt Drone will move backwards. Move the right Direction Stick up and the Stunt Drone will move forward. Move the right Direction Control down and the Stunt Drone will move backward. A A AAAAAAAAAA B B BBBBB B A A BBBBBBB A B B B B A AAA AABBBAA AAA B BBAAABBA AAA B A Move the right Direction Control left and the Stunt Drone will bank to the left. Move the right Direction Control right and the Stunt Drone will bank to the right. 7 8 CALIBRATING THE STUNT DRONE 1. Place the Stunt Drone on a flat level surface. 2. Make sure the Stunt Drone is on and that the controller is synced
(refer to syncing pg 4). Do not start the blades. Instead move both the throttles and control stick down and to the right corner (see diagram E). You will hear a beep and see the lights on the drone rapidly flash and stop. Once the lights stop flashing you have completed your
TROUBLE SHOOTING: If you do not see the lights flash, first turn off the switch from the drone then turn off your controller and start again. Always make sure to turn on the switch in first, then turn on your controller. Push the left throttle stick up all the way and then pull back down again. When you hear the beep the Stunt Drone is synced to the controller and you are ready to calibrate. E HOW TO DO 360 STUNT ROLLS 1. In order to make your Note: The Stunt Drone
means you are now in STUNT MODE."
Stunt Drone will instantly roll in the associated direction. See diagram below. Note: REPLACING THE PROPELLER BLADE Your Stunt Drone propeller system is a precision instrument that may need repair or replacement from
to your Stunt Drone propellers. 1. The Stunt Drone has four blades, two gray color ones on front, and two black color ones on back (see
2. When replacing the propeller blades, make sure to match both the color and indication letter on the
Gray Blade Front Left = A Gray Blade Front Right = B Black Blade Back Left = B Black Blade Back Right = A FRONT A B B A REAR
J 9 10 STUNT DRONE WARNING:
The Stunt Drone is designed for INDOOR or OUTDOOR. The Stunt Drone blades revolve at high speeds and can cause damage to the user, spectators and animals. Stand away from the Stunt Drone to reduce the risk of getting into the flight path. Warn spectators that you will be flying your Stunt Drone so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the Stunt Drone. WARNING!
any other battery.
BATTERY WARNINGS RECHARGEABLE BATTERY:
battery properly according to local disposal requirements. CONTROLLER BATTERIES:
Remote control requires 2 AAA batteries (not included). Please read the important battery safety warning below.
according to state or local government ordinances and regulations.
CARE AND MAINTENANCE
extended period of time.
Limited 90-Day Warranty NORTH AMERICA AMAX Group USA warrants to the original consumer that this product is free from any electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If any such defect is discovered within the warranty period, AMAX Group USA will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and insured to our warranty center. The warranty covers normal consumer use and does not cover damage that occurs in shipment or failure that results from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use or unreasonable use of the unit. Removal of any parts/components voids all warranties. This warranty does not cover cost of repairs made or attempted outside by third-party individuals or companies. Any applicable implied warranties, including warranties of merchantability and fitness, are hereby limited to 90 DAYS from the date of purchase. Consequential or incidental damages resulting from a breach of any applicable express or implied warranties are hereby excluded. Some states do not allow limitations on the duration of implied warranties and do not allow exclusion of incidental or consequential damages, so the above limitations and exclusions in these instances may not apply. REPAIR/REPLACE PRODUCT If your product begins to malfunction or stop working, immediately email our warranty center at the email listed below. If it is determined that a return is necessary, our warranty department will issue you an RMA number/form and an address to the nearest return center for shipping the product to. IMPORTANT NOTICE: We will reject all returns that are not accompanied by an issued RMA form and number so make sure to contact our warranty center before attempting to return your product!
PREPARATION FOR SHIPPING YOUR PRODUCT Please repack your product in a durable box, preferably in the original carton, and send it prepaid, and adequately insured. Include the RMA form that was issued by our warranty department along with your daytime telephone number and email address inside the shipping carton. If your warranty has expired, contact our warranty center for charged service. For further information please send all inquiries to: customercare@amaxbrands.com IMPORTANT NOTICE! DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT FIRST CONTACTING OUR WARRANTY DEPARTMENT BY EMAIL AT:
customercare@amaxbrands.com 11 12