FCC ID: 2ASK3ASC-6214T PA1009 micro 3.5CH helicopter / Ultra Micro Drone

FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. PA-1009 ULTRA MICRO HELI with Gesture Control Technology WARNING!

CHOKING HAZARD - Small parts. Not suitable for children under 3 years. INSTRUCTION BOOKLET WARNING: Never leave product charging unattended for extended periods of time. Always disconnect helicopter from charger immediately after the helicopter is fully charged. Please refer to enclosed safety instructions. THIS PACKAGE CONTAINS:

Conforms to safety requirements of ASTM, FCC and CPSIA. Voyage Aeronuatics is the registered trademark of Amax Group USA, LLC. AMAX Group USA Address: 12645 Memorial Dr Suite F1 #388 Houston, TX 77024 2020 All Rights Reserved. visit us at www.amaxbrands.com 11 Made in China C011-USA-V1.0 PA-1009 Remote Control USB Charging Cord Spare Rotor Blades Instruction Booklet Colors and styles may slightly vary. ARTWORK NO. DESCRIPTION MDSER DESIGNER DATE IM.ai 110 x 173MM Johnny TABLE OF CONTENTS Features. 1 Charging the Remote Control. 2 Charging the Helicopter. 2 Helicopter diagram, Remote Control diagram. 3 Preparing for Flight . 3 Flying Tips. 4 How to Sync your Helicopter . 4 Flight Controls. 5 Automatically Take Off / Land. 6 Helicopter Warning And Safety Precautions. 6 Part Replacement Instructions. 7 Contents. 7 PA-1009 Propeller System. 7 Replacing the Upper Propeller Blade . 8 Replacing the Bottom Propeller Blade . 8 Battery Warnings. 9 Care and Maintenance. 9 Limited 90-Day Warranty. 1 0 FCC Information. 1 1 Thank you for purchasing the PA-1009 2.4GHz Motion Controlled Helicopter. Please read this instruction booklet carefully as it contains valuable information on how to properly fly and care for your helicopter. FEATURES Worlds Smallest 3CH RC Helicopter 6 Axis Gyro Auto Stabilization Automatic Altitude Lock One-Button Auto Start and Land New Intuitive Gesture Motion Controller (Included) Rechargeable Lipoly Battery. CHARGING THE REMOTE CONTROL 1. Make sure the Controllers power switch is OFF and remove protection cover. (see diagram A ). 2. Plug the USB to your computers USB port or a USB wall charger (see diagram B). 3. The red LED lights on the CONTROLLER turns solid when charging is complete. Note: If the red LED lights flashing indicate the controller is under charging process. 4. The charging time will vary depending on the percentage of battery already charged. The average charging time is approximately 60 minutes. A B CHARGING THE HELICOPTER 1. Make sure the helicopters power switch is in the OFF position and plug the USB charging cord into the charging socket of the helicopter(see diagram C ). 2. Connect the USB end of the cable to your computers USB port or a USB wall charger (see diagram D). 3. The red LED on the USB plug lights up when charging is complete (See diagram E). Note: If the red LED lights up, either the charging is complete or the USB plug is not properly connected. 4. The charging time will vary depending on the percentage of battery already charged. The average charging time is approximately 30-40 minutes( via 5.0V 2A USB wall charger). The helicopter operates for approximately 4 minutes per charge. The red LED on the USB plug lights up when charging is complete C D E IMPORTANT: ALWAYS DISCONNECT CHARGER CORD AFTER CHARGING. NEVER LEAVE CHARGER CONNECTED TO HELICOPTER OVERNIGHT OR FOR EXTENDED PERIODS OF TIME. 1 2 HELICOPTER DIAGRAM Below is a basic list of features and parts on the helicopter. PREPARING FOR FLIGHT Verify that there are the helicopter and remote control has been fully charged. Make sure your helicopter is turned on and properly synced to your remote control (See SYNC YOUR HELICOPTER below). Fly only in a large room free of obstacles with an open radius of at least 25 feet. Close all windows and doors, turn off fans and close air ducts or any other openings that may cause drafts in the room. IMPORTANT: YOUR PA-1009 HELICOPTER IS DESIGNED FOR INDOOR USE ONLY. DO NOT FLY OUTDOORS. SYNCING YOUR HELICOPTER Your PA-1009 utilizes an automatic 2.4G selection system that allows up to 8 people to fly side by side in the same wireless range. FOR ONE PERSON PLAY:

1. Before starting, make sure that both your remote control and helicopter are turned OFF. Make sure that there are no other 2.4G devices nearby. 2. Turn ON the helicopter and set it down on a flat surface. The red LED indicators flashing on the helicopter head, This means your helicopter is searching for a controller to pair with. 3. Turn ON your remote control. Roll the Throttle wheel forward and Roll the Throttle wheel remote control are synced. When this happens you have properly synced your helicopter and you are ready to fly. Note: If the LED indicators do not stay solid, repeat steps 1-3 to sync the helicopter again. backwards.The LED indicators on the helicopter stay solid, indicating that the helicopter and FOR MULTI-PERSON PLAY:

4. Before starting, make sure that all of the helicopters and remote controls are turned off. Make sure that there are no other 3 devices nearby. 5. Players must sync their helicopters successively. Make sure that no one else is syncing while you sync your helicopter by following steps 1 to 3 above. 6. When a players helicopter is synced and working it should be left ON while the other players sync their helicopters. 7. Should there be a mistake or interference, all players must turn off their remote controls and helicopters and start the process all over again. Tail Blade Landing Gear Charging Socket REMOTE CONTROL DIAGRAM Throttle Wheel Start & land Power Button Stabilizer Bar Main Rotor Blades Body Shell LED Lights Power Switch Calibrating /Speed Button Power Indicator Charging Indicator USB Cover 3 4 CALIBRATING THE PA-1009 If the PA-1009 becomes unstable during the course of flying, you may need to calibrate the internal gyros. To do this place the PA-1009 on a flat level surface. Long press calibrating button. The LEDs on the PA-1009 will flash quickly and then remain solid, this indicates your helicopter has been recalibrated (see diagram F). AUTOMATICALLY TAKE OFF / LAND Make sure you have properly synced The PA-1009. Simply press the Throttle wheel/start & land down on the controller, your PA-1009 will automati-

F To stop or land the PA-1009 just press the Throttle wheel/start & land down again and the PA-1009 cally take off. will descend and land automatically. Tilt the controller backward and the helicopter will move backward. FLIGHT CONTROLS While youre learning to fly your helicopter, it is best to start with a large room until you get used to the basic controls. Tilt the controller left and the helicopter will spin counterclockwise. Roll the Throttle wheel forward to increase the speed of the main rotor, and roll the Throttle wheel backwards to decrease the speed of the main rotor. The helicopter will rise or descend accordingly. Tilt the controller right and the helicopter will spin clockwise. SPEED CONTROL: Your PA-1009 helicopter can operate in beginner (slower) or advanced (faster) speed mode. Simply press the Speed Button to switch the speed. Tilt the controller forward and the helicopter will move forward. 5 6 PART REPLACEMENT INSTRUCTIONS CONTENTS:

(1) 2 upper propeller blade x 2 (3) 4 connecting rods

(2) 2 bottom propeller blade x 2 (4) 4 screws x 4 x 4 GYRO-STABILIZED 3CH WIRELESS INDOOR HELICOPTER PROPELLER SYSTEM Your Gyro-Stabilized 3CH Wireless Indoor Helicopter propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your Gyro-Stabilized 3CH Wireless Indoor Helicopter propeller or propeller connecting rods. TROUBLESHOOTING:

If your Gyro-Stabilized 3CH Wireless Indoor Helicopter loses its ability to fly correctly, please inspect the propeller system carefully for the following two common issues:

1. Replacing Connecting Rod: The connecting rod is a small handcuff style device that stabilizes the upper propellers. There are two connecting rods on the upper propeller. Please see (Diagram 1). If a connecting rod is broken or missing simply replace it by peeling off the existing broken unit and replacing it with a new one. You may have to use slight pressure when reattaching both ends of the new connecting rod. Make sure that the new connecting rod is secured and locked in place. See

(Diagram 2). For changing connecting rod, make sure there is no damage to the actual blade or arm that holds the connecting rod in place. If there is you must replace the entire blade system. 2. Replacing Upper and Bottom Propeller: The propeller is subject to damage as you learn to properly fly and control your Gyro-Stabilized 3CH Wireless Indoor Helicopter. If after a crash your helicopter has loss of control or flies erratically you should carefully inspect your entire propeller system for any sign of damage. Most common are: cracked or chipped blade, broken connecting rod, frozen balance bar (this is when the balancing bar and blade are jammed and can not move freely up and down). To replace the propeller blades follow diagrams 3 through 12. Replacing Connecting Rod Diagram 1 Diagram 2 REPLACING THE UPPER PROPELLER BLADE Using a screwdriver turn counter clockwise to remove the screw. Remove the broken blade and carefully replace with a new one. When you tighten the screw you should test the blade to make sure that it still has free movement. If the blade cannot move freely, slightly loosen the screw. Using the screwdriver turn clockwise to tighten the two screws. Upper Blade Diagram 7 Please note the design of the upper blade. REPLACING THE BOTTOM PROPELLER BLADE Using a screwdriver turn counter clockwise to remove the screw. Remove the broken blade and carefully replace with a new one. Diagram 4 Diagram 6 Diagram 9 Diagram 11 Diagram 3 Diagram 5 Diagram 8 Diagram 10 Diagram 12 There are two propeller connecting rods on the upper propeller. Broken connecting rod Broken connecting rod Using the screwdriver turn clockwise to tighten the two screws. When you tighten the screw you should test the blade to make sure that it still has free movement. If the blade cannot move freely, slightly loosen the screw. Replacing connecting rod Proper connection 7 Bottom Blade Please note the design of the bottom blade. 8 HELICOPTER WARNING AND SAFETY PRECAUTIONS The helicopter blades revolve at high speeds and can cause damage to the user, spectators, and animals. Stand away from the helicopter to reduce the risk of getting into the flight path. Warn spectators that you will be flying your helicopter so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the helicopter. WARNINGS Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades. Keep hands, hair, and loose clothing away from the propeller when the power switch is turned to the ON position. Turn off the transmitter and helicopter power switches when not in use. The charging cable is for charging the helicopters Li-poly battery. Do not use it to charge any other battery. Parental supervision recommended when flying the helicopter. BATTERY WARNINGS RECHARGEABLE BATTERY:

This helicopter uses an internal Li-Poly rechargeable battery and is not replaceable. If the battery can no longer be charged, dispose of the helicopter properly according to local disposal requirements. CARE AND MAINTENANCE To clean, gently wipe the remote control and helicopter with a clean damp cloth. Keep the toy away from direct heat or sunlight. Do not submerge the toy into water. This can damage the unit beyond repair. NORTH AMERICA Limited 90-Day Warranty AMAX Group USA warrants to the original consumer that this product is free from any electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If any such defect is discovered within the warranty period, AMAX Group USA will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and insured to our warranty center ALONG WITH THE ORIGINAL RECEIPT evidencing that the product was purchased from an approved AMAX retail partner and that the product is still within the 90 day warranty period. The warranty covers normal consumer use and does not cover damage that occurs in shipment or failure that results from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use or unreasonable use of the unit. Removal of any parts/components voids all warranties. This warranty does not cover cost of repairs made or attempted outside by third-party individuals or companies. Any applicable implied warranties, including warranties of merchantability and fitness, are hereby limited to 90 DAYS from the date of purchase. Consequential or incidental damages resulting from a breach of any applicable express or implied warranties are hereby excluded. Some states do not allow limitations on the duration of implied warranties and do not allow exclusion of incidental or consequential damages, so the above limitations and exclusions in these instances may not apply. REPAIR/REPLACE PRODUCT If your product begins to malfunction or stop working, immediately contact our warranty center (contact details listed below). If it is determined that a return is necessary, our warranty department will issue you an RMA number/form and an address to the nearest return center for shipping the product to us. When honoring the warranty, AMAX reserves the right to either repair, replace or refund the product. IMPORTANT NOTICE:

We will reject and return to sender returns that are not accompanied by an AMAX issued RMA form and RMA number so make sure to contact our warranty center before attempting to return your product!

PREPARATION FOR SHIPPING YOUR PRODUCT:

Please repack your product in a durable box, preferably in the original carton, and send it prepaid, and adequately insured. Include the RMA form that was issued by our warranty department along with your daytime telephone number and email address inside the shipping carton. If your warranty has expired and you still require service please contact our customer care team For further information please send all inquiries to:

customercare@amaxbrands.com IMPORTANT NOTICE!

DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT FIRST CONTACTING OUR WARRANTY DEPARTMENT AT:

www.amaxbrands.com Email: customercare@amaxbrands.com 9 10

FCC ID: 2ASK3ASC-6214T This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Amax Industrial Group China Co. Limited 852.3962.5160 Model Number: ASC-6214 F08B01D05/2020 Shenzhen, China 25MM 23MM

AMAX INDUSTRIAL GROUP CHINA CO., LTD Date: March 19,2019 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Neon chen. Company Nam. AMAX INDUSTRIAL GROUP CO,.LTD Contact Name: Nancy Chen Title of Person : QA Manager Address: OFFICE NO.3 10/PF WITTY COMMERCIAL BUILDING IA-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG

AMAX INDUSTRIAL GROUP CHINA CO., LTD Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2ASK3ASC-6214T To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: AMAX INDUSTRIAL GROUP CHINA CO., LTD Contact Name: Nancy Chen Title of PersonQA Manager Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG Date:6/09/2020

AMAX INDUSTRIAL GROUP CHINA CO., LTD Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG Confirmation Letter We, AMAX INDUSTRIAL GROUP CHINA CO., LTD Remote Control FCC ID: 2ASK3ASC-6 214T And model No.: VL-6004, VL-6005, ASC-62 14, ASC-6216 ASC-6216, ASC-6214, VL-6005 have the same technical construction including circuit diagram, PCB Layout, electrical construction and mechanical construction with VL-6004.The difference lies only the model number and color. components component layout, and all Drone FCC ID: 2ASK3ASC-6214R And model No.: VL-6004, VL-6005, ASC-6214 ASC-6214, VL-6005 have the same technical construction including circuit diagram, PCB Layout, components and component layout, all electrical construction and mechanical construction with VL-6004.The difference lies only the model number and color. Nancy Chen AMAX INDUSTRIAL GROUP CHINA CO., LTD