FCC ID: 2ASK3GV-6128T Savage/Savage II

s AVAGE AWD OFF-ROAD Racer TM STEERING WHEEL TRIM ADJUSTMENT If the vehicle cannot go forward in a straight line you may need adjust the steering wheel trim. The steering wheel trim manual adjuster can be found on the bottom (underside) of the truck (SEE DIAGRAM F). From time to time you will need to adjust the steering trim. F WARNING DO NOT USE CAR IN INCLIMATE WEATHER!

TROUBLESHOOTING Before sending your car in for repair, please check for a solution below. Problem Possible Cause(s) Solution Car will not move. Weak batteries; no batteries Car does not respond properly to remote control. Car and remote not synced properly Another RC car may be transmitting on the same radio frequency Install new batteries in remote control and recharge the car battery. Refer to sync section and re-sync your car and remote. Move to a new location where no other RC cars are present. Car loses connection to remote control. Using car in a small enclosed area Using car indoors Low batteries in transmitter or vehicle Move outdoors to a large open area. Install new batteries in remote control or recharge your car. Car battery has fully charged, but slower than normal. Driving car for too long at high speeds, causing motor to overheat Turn car off for 10-15 minutes. SAFETY WARNINGS!

Improper use of batteries may lead to overheating, breakage or leaking.

- Do not mix old and new batteries.

- Do not mix different battery brands.

- Install batteries with correct polarity. The flat side (negative terminal) of the battery should rest against the spring.

- Remove dead batteries immediately.

- Avoid liquids, which can short circuit the batteries.

- The truck or remote will become unresponsive when batteries are low, at which point you should replace all batteries with new ones.

- Remove the batteries if you will not use the truck for a long time. Avoid using near furniture or glass to prevent damage to these objects. Do not play on roads. Do not play in crowded areas to avoid injury or damage. Choose a safe location away from traffic. Do not use truck during a storm or when lightning or thunder are present. Do not use in a wet , sandy or muddy environment as truck may become damaged. Do not modify or attempt to replace the built-in original antenna on the remote or truck. Doing so will damage the Do not pull on any wires that are part of the truck. Such action may cause the wires to break and the truck to malfunction. Keep fingers, hair and clothes away from the trucks spinning tires. Failure to do so may result in physical injury. Never aim the truck at other people. Do not throw the truck or purposely hit it with any object. Store truck in a cool environment, away from high-temperature sources such as fires, stoves, radiators, etc. This truck has no user-serviceable parts. Do not attempt to modify components or circuit board. set and affect operation. FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Distributed by:

TRACTOR SUPPLY COMPANY 5401 VIRGINIA WAY BRENTWOOD, TN 37027 For customer support, call: 1-888-376-9601 www.TractorSupply.com INSTRUCTION MANUAL Thank you for choosing SAVAGETM. With proper care your new vehicle will bring you many hours of enjoyment. Please read this instruction manual completely before using the product for the first time, and then keep this manual in a handy place for future reference. Conforms to safety requirements of FCC, ASTM and CPSIA. Savage is the registered trademark of AMAX Group AMAX Group USA Address: 12645 Memorial Dr Suite F1 #388 Houston, TX 77024 2020 All Rights Reserved. visit us at www.amaxbrands.com Made in China C012-USA-V1.0 8 Colors and styles may slightly vary. PACKAGE CONTENTS SAVAGETM AWD Off-Road Racer Remote control USB charger 7.4V Li-poly battery pack Screwdriver CHARGING THE BATTERY 1. Insert the white (3-wire) battery charging plug into the USB charger's socket. The charging plug and the USB charger's socket will properly fit in only one direction. Note: never force a charging socket connection (SEE ILLUSTRATION A). 2. Connect the USB end of the charging cable to your computers USB port or a USB wall charger (SEE DIAGRAM B) , The Red CHARGE indicator light will turn on and remain solid to indicate that charging is in progress. 3. Average approximate charging time is between 2-3 hours depending on the amount of residual charge that your Li-poly battery has before you begin charging. Note these charging times are based on 5.0V system with 2.0A or higher USB outlet. 4. The truck will run for approximately 30-40 minutes on a full charge. 5. The red led charging indicator light will turn off when the battery is fully charged. Note: Periodically examine the charger should be for damage that may result in the risk of fire, electric shock, or injury to persons. Do not use a damaged adapter. Open the controller battery cover which is located on the bottom of the remote control (SEE DIAGRAM E). Insert 4 AA 2. Installing the AA batteries into the remote control. batteries (not included) into the battery compartment. Make sure to carefully check that you have inserted the batteries in the correct direction by matching the polarity markers (+ and -) which are embedded in the plastic on the inside. When finished replace the battery cover and turn on your controller. If you have installed the AA batteries in the correct direction your controller indicator light will turn on (SEE REMOTE DIAGRAM). If the controller indicator light does not turn on you will need to re-check the installation direction of your batteries. TRUCK DIAGRAM (BOTTOM VIEW) BATTERIES NOT INCLUDED (4XAA) E Steering Wheel Trim Battery Compartment ON/OFF Switch A SET-UP 1. How to Install the battery into the truck:

Carefully pull off the battery cover lock on the bottom of the truck (SEE DIAGRAM C). Next connect the battery power plug into the truck socket power input socket (this is the black cable, 2 wire plug). Remember, the battery plug and the trucks power socket one properly fit in one direction, NEVER FORCE THE CONNECTION (SEE ILLUSTRATION D). After properly connecting the battery to the vehicle, replace the battery cover and lock it in securely. REMOTE DIAGRAM Power Indicator ON/ OFF Switch Speed Mode Button Nonfuction Buttons Steering Throttle Red Charging Light B D Battery Compartment C SYNCING YOUR SAVAGE Your Savage features an automatic 2.4G channel selection system that allows up to 8 people to race side by side in the same wireless range. For One Player:

1. Before starting, make sure that the power on both your remote control and truck are in the OFF position. Make sure that there are also no other 2.4G devices in the immediate area that area that are powered on. 2. First, turn on the truck and set it down on a flat surface. The head lights and tail lights will be illuminated. 3. Second, turn on the remote control. When the remote control's power indicator should begin flashing. If the indicator light is flashing this means your ready to pair. Simply pull the throttle lever all the way down. You will hear an engine start-up sound and the indicator light on the controller should now be solid. This means you have successfully paired your vehicle with the controller and you are ready to play! Note: If the light does not go solid, this means you were unable to sync your vehicle and you will have to start steps 1-3 ever again How to Sync with multiple Players in the same vicinity:

1. Before starting, make sure that the power on all vehicles and controllers are in the OFF position. Also make sure that there are no other 2.4G wireless devices in the vicinity. 2. Each player will have to sync their vehicle one at a time to avoid cross interference, individually at a different time to avoid interference. (follow syncing steps 1-3 above) Important: after successfully syncing a vehicle you must leave it ON until all players have successfully completed syncing their vehicles. 3. If there is interference, all players must turn off their controllers and trucks and restart the syncing process. OPERATION THIS IS A HIGH-SPEED OUTDOOR RC TRUCK. DO NOT PLAY INSIDE YOUR HOME OR OTHER SMALL ENCLOSED AREAS. Driving your truck:

Pull the throttle halfway down to drive forward at low speed. Pull the throttle all the way down to drive at maximum speed. Push the throttle forward to make truck stop or move in reverse. To break or quickly stop simply pull or push the throttle in the opposite direction. SPEED MODE The Savage has two speed settings, simply press the Speed Mode Button to change the Savage speed from normal speed (10 KM/H ) to high speed (13 KM/H ) ( SEE REMOTE DIAGRAM).

FCC ID: 2ASK3GV-6128T This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.1MM 6.4MM 27.4MM 56MM FCC ID: 2ASK3SC-2065T

AMAX INDUSTRIAL GROUP CHINA CO., LTD Date: March 19,2019 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Neon chen. Company Nam. AMAX INDUSTRIAL GROUP CO,.LTD Contact Name: Nancy Chen Title of Person : QA Manager Address: OFFICE NO.3 10/PF WITTY COMMERCIAL BUILDING IA-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG

AMAX INDUSTRIAL GROUP CHINA CO., LTD Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2ASK3GV-6128T To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: AMAX INDUSTRIAL GROUP CHINA CO., LTD Contact Name: Nancy Chen Title of PersonQA Manager Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG Date: 5/18/2020