FCC ID: 2ASK3RB-6283T SMART BOTSRECHARGEABLE INFRARED SNAKE/RC Snake-Large

FCC Part 15 B Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This product is manufactured by Amax Group 12645 Memorial Drive, Suite F1, #388, Houston, TX 77024 Smart Bots are the registered trademarks of Amax Group 2021 All rights reserved. Visit us at www.amaxbrands.com KEEP THIS PACKAGE FOR REFERENCE AS IT CONTAINS IMPORTANT INFORMATION. Conforms to safety requirements of ASTM, CPSIA, and FCC. RECHARGEABLE Infrared SNAKE NOTE:

THIS SNAKE IS BUILT FOR INDOOR USE ONLY AND WILL ONLY WORK ON SMOOTH AND FLAT SURFACES. PLAYING WITH THIS PRODUCT OUTDOORS OR ON A CARPET MAY PERMANENTLY DAMAGE THIS PRODUCT. FOR BEST RESULTS, ALWAYS POINT THE TRANSMITTER DIRECTLY TOWARDS THE HEAD OF THE SNAKE FROM WITHIN A FIVE FOOT RADIUS. INSTRUCTION MANUAL Warning: roboratler snake is an infrared snake. Due to the interference of the sun, the infrared signal can not work in the daytime. Refer to the attached safety instructions. INFRARED BEAMS DO NOT BOUNCE OF BLACK/DARK MATTE SURFACES AND MAY AFFECT TRANSMISSIONS FROM CONTROLLER. PACKAGE CONTAINS:

Distributed by:

TRACTOR SUPPLY COMPANY 5401 VIRGINIA WAY BRENTWOOD, TN 37027 For customer support, call: 1-888-376-9601 www.TractorSupply.com 9 Made in China C012-USA-V1.0 R/C Snake Wireless Infrared Controller Instruction Booklet Product may vary slightly from photograph. ARTWORK NO. DESCRIPTION MDSER DESIGNER DATE C12 112172mm Johnny 2020/4/08 TABLE OF CONTENTS Features. 1 Transmitter Batteries Installation. 2 Product battery installation. 2 RC Snake Diagram. 3 Remote Control Diagram. 3 Playing with Your Snake. 4 Invisible Leash Mode. 4 Interactive/pet Mode. 4 Basic Controls. 5 Adjusting the Trim. 5 Battery Warnings. 6 Care and Maintenance. 6 Limited 90-Day Warranty. 7 FCC Part 15 B Notice. 9 Thank you for purchasing the ROBORATTLER Remote Control Snake. The RoboRattler is an exciting action toy that requires user participation to properly control the snake. Please read this instruction booklet as it contains valuable information on how to properly use and care for your Snake. Start by ensuring that the snake is fully charged and new batteries have been properly installed in the snakes included wireless "egg" shaped controller. Transmitter Batteries Installation 1. Use a Phillips head screwdriver to unscrew battery cover at the back of the transmitter. In an counterclockwise direction, open the battery cover (Fig.1). 2. Place 2 AAA batteries ( not included) according to the polarity (Fig.2). 3. Close the battery cover, use the screwdriver to screw it in clockwise direction

(Fig.3). NOTE: THIS R/C TOY SNAKE IS BUILT FOR INDOOR USE ONLY AND WILL ONLY WORK ON SMOOTH AND FLAT SURFACES. PLAYING WITH THIS PRODUCT OUTDOORS OR ON A CARPET MAY PERMANENTLY DAMAGE THIS PRODUCT.

(Fig. 1)

(Fig. 2)

(Fig. 3) Product battery installation 1. Screw off the battery cover on the back of the toy with a crosshead screwdriver. Open the battery cover counterclockwise (Fig. 4). 2. Place 4 AAA batteries ( not included) according to the polarity (Fig. 5). 3. Close the battery cover and screw it in clockwise with a screwdriver (Fig. 6). Features Realistic Slithering Motion Egg Shaped Remote Controller NEW Interactive Pet Mode Automatically Engages Pets NEW Sensors In The Eyes Detect Walls And Other Obstacles

(Fig. 4)

(Fig. 5)

(Fig. 6) 1 2 RC Snake Diagram infrared sensor Wheel ON/OFF Switch Bottom Remote Control Diagram Functional indicator Turn left key

(Additional adjustment function Key) Forward/Pause key

(Additional adjustment function Key) Turn right key

(Additional adjustment function Key) Mode Toggle between the two modes by short press the MODE button in the center of Playing with Your Snake The Egg controller has 2 operation modes:

Mode 1: Invisible Leash mode (Red Indicator Light) Mode 2: Interactive/Pet mode (Green Indicator Light) the controller. INVISIBLE LEASH MODE:

In invisible leash mode you magically control the snake just like a pet! Simply point the transmitting led at the front of the controller directly at the head of your snake and follow the snake around! The snake will respond to your commands from up to 10 feet away!

Important: Remember to always point the egg towards the snakes head and to stay within a ten feet range (Fig. 9). If you go out of range, point the egg in a different direction or stop pushing the controls, the snake will go into AUTONOMOUS MODE using its on-board sensors to avoid most obstacles on its way.

(Fig. 8)

+10 FT T E E F 0 2 T F 0 1

20 FEET

1 0 F T

+10 FT Maximum wireless operational range is a 20 foot

diameter. Operator should stand in the center of wireless range and allow a 10 feet circumference of unobstructed space for best results. Environmental conditions and battery strength may effect wireless range. Please review usage diagram

*Distance is approximate, as environmental conditions may cause variations. INTERACTIVE/PET MODE:

Push the mode button on the snakes controller and use your hand or foot crosses the sensors in its eyes and it will scurry around for 10 seconds and then suddenly stop. The snake will lie there still until something crosses the sensors in its eyes and then it will automatically scurry randomly again and stop! This is a great mode for scaring unsuspecting people and playing with Pets!

(Fig. 9) unsuspecting pet walks towards snake eye sensors activate snake Important! Remember to always turn off the On/Off switch on the bottom of the snake when you finish playing to extend battery life. 3 4 Basic Controls

(1).Forward/Pause:

Press the Forward/Pause key to make the rattle snake move forward; Then press the Forward/Pause key once again and the snake will pause from moving. (Fig.10)

(2).Turn left:press the turn left key on the transmitter. (Fig.11) Forward/Pause key

(Fig. 10)

(Fig. 11) turn left key Battery Warnings CAUTION: If the battery leaks fluid, avoid contact with eyes and dispose the SNAKE according to the local law. CONTROLLER BATTERIES:

The transmitter requires 2 AAA batteries (no included). Please read the important battery safety warnings below. Do not mix alkaline, standard (carbon-zinc), and rechargeable batteries

(Nickel Metal Hydride). Do not mix old and new batteries. Non-rechargeable batteries are not to be recharged. Rechargeable batteries are only to be charged under adult supervision. Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations. The supply terminals are not to be short-circuited. Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity (see inside booklet for diagram). Do not dispose batteries in a fire; batteries may leak or explode.

(3).Turn right: press the turn right key on the transmitter. (Fig.12)

(Fig. 12) Turn right WARNING: A swallowed Button or Coin Cell Battery can cause internal chemical burns in as little as two hours and lead to death.Dispose of used batteries immediately. Keep new and used batteries away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Care and Maintenance Always remove the batteries from the remote control when it is not being used for an extended period of time. To clean, gently wipe the remote control and SNAKE with a clean damp cloth. Keep the toy away from direct heat or sunlight. Do not submerge the toy into water. This can damage the unit beyond repair. Parental guidance is recommended when installing or replacing the batteries. IMPORTANT SAFETY INFORMATION: Keep your SNAKE away from face and eyes. NOTE: FOR BEST RESULTS, ALWAYS POINT THE TRANSMITTER DIRECTLY TOWARDS THE HEAD OF THE SNAKE FROM WITHIN A FIVE FOOT RADIUS. Adjusting the Trim Adjusting the Trim For a more realistic experience, the snake will slither from side to side in a continuous random motion. If the snake tends to drift to the right or left, and youd prefer to move it in a more straight and forward motion, you may make an adjustment to trim or tune the snake.

(1).Turn the snake ON by switching the ON/OFF switch on the underside of the snake to the ON position. Then set the snake on the floor, belly down.

(2).Turn ON the Egg shaped transmitter and press the forward/pause button once. The snake should begin to slither in a forward direction.

(3). If the Snake inadvertently drifts to the left or right while in slither mode, you may ENTER the trim mode by holding down both the LEFT and RIGHT direction buttons for 4 seconds. You will see the flashing indicator light on the front of the transmitter change speed and rhythm. This signifies that you are in the Trim Adjustment Mode.

(4).To counter balance a left drifting snake press the RIGHT turn arrow repeatedly until the snake is moving in a generally straight direction.

(5).To counter balance a right drifting snake press the LEFT turn arrow repeatedly until the snake is moving in a generally straight direction.

(6). When finished with the Trimming. You can exit the Trim Adjustment Mode by pressing and holding the "Forward/Pause" button till the LED indicator on the transmitter stop blinking. 5 6 NORTH AMERICA Limited 90-Day Warranty AMAX Group USA warrants to the original consumer that this product is free from any electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If any such defect is discovered within the warranty period, AMAX Group USA will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and insured to our warranty center ALONG WITH THE ORIGINAL RECEIPT evidencing that the product was purchased from an approved AMAX retail partner and that the product is still within the 90 day warranty period. The warranty covers normal consumer use and does not cover damage that occurs in shipment or failure that results from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use or unreasonable use of the unit. Removal of any parts/components voids all warranties. This warranty does not cover cost of repairs made or attempted outside by third-party individuals or companies. Any applicable implied warranties, including warranties of merchantability and fitness, are hereby limited to 90 DAYS from the date of purchase. Consequential or incidental damages resulting from a breach of any applicable express or implied warranties are hereby excluded. Some states do not allow limitations on the duration of implied warranties and do not allow exclusion of incidental or consequential damages, so the above limitations and exclusions in these instances may not apply. REPAIR/REPLACE PRODUCT If your product begins to malfunction or stop working, immediately contact our warranty center (contact details listed below). If it is determined that a return is necessary, our warranty department will issue you an RMA number/form and an address to the nearest return center for shipping the product to us. When honoring the warranty, AMAX reserves the right to either repair, replace or refund the product. IMPORTANT NOTICE:

We will reject and return to sender returns that are not accompanied by an AMAX issued RMA form and RMA number so make sure to contact our warranty center before attempting to return your product!

PREPARATION FOR SHIPPING YOUR PRODUCT:

Please repack your product in a durable box, preferably in the original carton, and send it prepaid, and adequately insured. Include the RMA form that was issued by our warranty department along with your daytime telephone number and email address inside the shipping carton. If your warranty has expired and you still require service please contact our customer care team For further information please send all inquiries to:

customercare@amaxbrands.com IMPORTANT NOTICE!

DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT FIRST CONTACTING OUR WARRANTY DEPARTMENT AT:

www.amaxbrands.com Email: customercare@amaxbrands.com 7 8

FCC ID: 2ASK3RB-6283T This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 6.3mm 56.5mm

AMAX INDUSTRIAL GROUP CHINA CO., LTD Date: 2021/3/17 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) c) d) e) f) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

g) h) i) j) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Company Name: AMAX INDUSTRIAL GROUP CHINA CO., LTD Contact Name: Nancy Chen Title of PersonQA Manager Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG

AMAX INDUSTRIAL GROUP CHINA CO., LTD Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2ASK3RB-6283T To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: AMAX INDUSTRIAL GROUP CHINA CO., LTD Contact Name: Nancy Chen Title of PersonQA Manager Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG Date: 5/7/2021

AMAX INDUSTRIAL GROUP CHINA CO., LTD Address: OFFICE NO.3 10/F WITTY COMMERCIAL BUILDING 1A-1L TUNG CHOI STREET MONGKOK KOWLOON HONG KONG Confirmation Letter We, AMAX INDUSTRIAL GROUP CHINA CO., LTD The product: SMART BOTSRECHARGEABLE INFRARED SNAKE/RC Snake-Large FCC ID: 2ASK3RB-6283T And model No.: RB-6283/1638228 1638228 have the same technical construction including circuit diagram, PCB Layout, components and component layout, all electrical construction and mechanical construction with RB-6283.The difference lies only the model number.

(Signature) ___________