FCC ID: 2AH6G-TP450 Printer

TP450 User Guide

www.entrylogic.com

This box contains the following:

Paper Roll Installation:

1 TP450 Printer

1 Power Adapter

1 User Manual

1.

Open top cover

2.

Drop paper roll in

the hole as illustrated

3.

Pull the paper into the

paper holder,then close

top cover

4.

Print one self-test to

make sure paper

correctly installed.

1 Power Cable

1 Button Name Indicator

Printer Function Introduction:

1 USB Cable

1) FEED Button

2) PAUSE Button

3) POWER/ON LINE Indicator

4) ERROR Indicator

Power

Indicator

Pause

Indicator

ERROR Indicator

FEED Button

Item Functions

Descriptions

Buttons:

Feed

Pause

1

2

3

Press the FEED button when POWER indicator is on and

ERROR indicator is off. It feeds the label to the beginning of

the next label.

Press the FEED button during printing and the printing

job is suspended

Self-test

1. Turn off the printer power.

2. Make sure the paper roll is installed correctly and the

printer top cover is close

3. Press the FEED button and turning on the printer power

simultaneously. When the self-test paper comes out, release

the FEED button.

4

Dump mode

1. Turn off the printer power.

2. Make sure the paper roll is installed correctly and the

printer top cover is close

3. Press and hold on the PAUSE button and FEED button, then

turn on the printer power. When the POWER indicator and

ERROR indicator light simultaneously release both buttons.

The printer is changed to Dump Mode.

5

Mode Switch

1. Turn off the printer power.

2. Make sure the paper roll is installed correctly and the

printer top cover is close

3. Press PAUSE button, then turn on the printer power. When

the POWER indicator and ERROR indicator light, print mode

switching prompt after 2-3 seconds,and both lights flash at

the same time.Press the FEED button to switch modes.

Then restart the printer.

6

Initialize

1. Turn off the printer power.

2. Press and hold on the PAUSE button and FEED button,

then turn on the printer power. When the POWER indicator

lights and ERROR indicator dims,release both buttons.

The printer DRAM is cleared and printer settings are

restored to defaults.

Connection:

A) Connect AC power cord to

power,DC power cord to printer.

B) Connect printer and

compter/tablet.

B) Power Cord

A) USB Interface

Driver installation

Method 1: Port installation

1) double click the driver installation file;

2) select and install the printer driver and proceed ,then to the next step;

3) select, other, next step;

4) choose the type of printer and go to the next step;

5) specify the port and select according to the current printer;

6) when the printer driver installation prompts that the installation is successful, click"finish".

Method 2: Add mode installation

1) enter the interface of printer, click add printer;

2) click add local printer;

3) select the printer port, select the existing port

(select the port of your current printer), and next step;

4) select install from disk, browse and drive installation directory

(default C disk), select execute file and confirm;

5) choose the type of printer and go to the next step;

6) when the printer driver is installed and show successful, then click "finish".

ATTENTION:

Cleaning your printer

Clean your print if text is not clear,printed columns are unclear, or the paper feeds noisily.

1. Use your printer on stable surfaces, that avoid external vibrations.

2. Do not use or store printer in high temperature, high humidity, polluted environments.

3. Connect the power adapter properly to grounded receptacle. Avoid using the same socket

with large power consuming devices, that can lead to power flucutation.

4. Avoid water or other objects going into the printer. If this occurs, turn off the printer immediately

5. Printing without an installed paper roll will seriously damage the printing head.

6. Unplug your printer from power receptable when unused for long periods.

7. Only use approved accessories. Never try to disassemble, repair or remodel your printer.

8. Use standard power adapter.

9. Use high quality paper. This ensures the printing quality and life of the printer.

10. Please turn off power before plugging / unplugging cables.

11. The printer is only suitable for use in tropical climates below 5000 meters sea level.

Printer head cleaning steps:

1. Turn printer off, release power cord. Open top cover, and take out paper roll

2. Wait until printing head cools off if it’s just finished printing

3. Clean printing head completely using swab with alcohol (without water)

4. Until alcohol completely volatized, close top cover.

5. Connect power again, print test to check if clean.

PLEASE NOTE

1. Please make sure power is off during printer maintenance.

2. Do not touch or scratch the printing head surface, rollers, or sensors.

3. Avoid gas, acetone or other organic solvents.

4. Wait until alcohol has completely volatized, close the top cover, and

connect to power source again. Print a self-test to make sure your printer

is working properly.

TP450 User Guide

www.entrylogic.com

Bluetooth printer

Bluetooth printer setting

Bluetooth: It is a kind of technology with short distance wireless connection which

globally used, using the same 2.4GHz nearby free charge and free application for

frequency radio range with microwave. It can transfer data without alignment, with an

effective transmission range of 10m. The Bluetooth printer carries out data transmission

by matching with the Bluetooth device, the receiving master transfers the data to the

printer and print it out. Hand-held terminal with Bluetooth interface, laptop and other

information terminals could print via Bluctooth interface.

Mini receipt printer compatible with Bluetooth 2.1 standard, with the power level of

CLASS 2, and effective transmission distance is 10m. The name of the device is Printer

001, the initial password is "123456". Users may change the name of the device and

the password if necessary.

The Bluetooth printer need to be paired with the main device of Bluetooth before

working, the process of pairing will be started by the main device.

For detail pairing method, please refer to the function instructions for main device

of Bluetooth. When pairing, the Bluetooth printer should power on.

Note: If the name of the printer is not changed, please do not power on other

printers at the same time when pairing, otherwise it cannot identify which

printer is paired successfully.

1. Connect the printer with computer, turn on the printer. Open the "tools" folder in printer

CD, find the printer setting tools, choose the port and print a test page, if works, then enter

into "Advanced" option.

Note: Bluetooth printer and the port setting procedures: firstly connect the power

and run on the Bluetooth printer, connect the Bluetooth device to USB interface of

the computer (master), a Bluetooth icon at the lower right corner on the desktop

will appear.

2. Click "Bluetooth setting", set the related information such as the name of the

Bluetooth device and the password, then click "Setting". The printer will "beep" a sound.

Then restart the computer and check if the information of the self-test page printed matches

with the settings.

3. Enter "Control Panel" -- "Hardware and Sound" -- "Add a Blue tooth device" (Computer

should support Bluetooth function.

4. Default name of Bluetooth setting. Choose "Printer001", click "Next".

5. Choose "Enter the device's pairing code", enter the pass word" 123456", add the device.

6. After adding the device, choose "Equipment and printer", find the added Bluetooth device

Printer001, click the properties of hardware, check the port infonnation of the device.

7. After installing the printer driver, find the icon of driver, check the properties of it, choose

the right port and print a test page via driver.

ISED Canada Statement:

This device contains licence-exempt tasmittre(s)/receiver(s)/ that comply with Innovation Science and

Economic Development Canada 's licence-exempt RSS(s).

Operation is subject to the following two conditions:

1) this device may not cause interference and

2) this device must accept any interference, including interference that may cause undesired operation

of the device.

Radiation Exposure: This equipment complies with Canada radiation exposure limits set forth for an

uncontrolled environment

RF Exposure Statement

To maintain compliance with IC's RF Exposure guidelincs, This cquipment should be.installed and

operated with minimum distance of 20cm the radiator your body. This device and its antenna(s) must

not be co-located or operation in conjunction with any other antenna or transmitter

Déclaration de l'ISED Canada :

Cet appareil contient des tasmittre (s) / récepteur (s) sans licence / conformes à l'innovationRSS

exemptes de licence de Sciences et Développement économique Canada. L'opération est sous réserve

des deux conditions

suivantes :

1) cet appareil ne peut pas causer d'interférences et

2) ce dispositif doit accepter toute interférence, y compris peut provoquer le fonctionnement

indésirable de l'appareil.

Exposition aux rayonnements : Cet équipement est conforme aux radiations du Canada limites

d'exposition pour un environnement incontrôlé

noncé d'exposition RF

Pour maintenir le respect des guides d'exposition RF d'IC, cquipment doit être.installé et actionné avec

une distance minimale de 20cm le radiateur de votre corps. Cet appareil et ses antennes ne doivent pas

être co-localisé ou en opération en conjonction avec toute autre antenne ou émetteur

Specifications & Compliance

FCC and ISED Canada Compliance: This equipment has been tested and is in compliance

with Part 15 of the FCC Rules and ISED Canada license-exempt RSS standard(s). Operation

is subject to the following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may

cause undesired operation.

FCC-ID: 2AH6G-TP450

IC-ID: 26745-TP450

The AC Power Adapter has been tested and in compliance with the safety standards set forth

by Part 1: Safety Requirements in both the US [UL 62368-1:2014 Ed.2] and Canada

[CSA C22.2#62369-1:2014 Ed.2].

In accordance to local laws, when the device reaches end of life, it should be recycled in a

manner that protects human health and the environment. Please consult your local authorities

for local laws and regulations regarding the recycling and proper disposal of office electronics.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement

To maintain compliance with FCC's RF Exposure guidelines, This equipment

should be installed and operated with minimum distance of 20cm the radiator

your body. This device and its antenna(s) must not be co-located or operation

in conjunction with any other antenna or transmitter.

©2021 EntryLogic. All Rights Reserved. EntryLogic™ is a trademark of EntryLogic, Inc.

FCC ID LABEL:

Label Location

FCC ID: 2AH6G-TP450

Ca. 3mm x 7mm

AMBIR TECHNOLOGY INC. Agent Authorization Company: AMBIR TECHNOLOGY INC. Address: 820 Sivert Drive, Wood Dale, Illinois 60191 United States Product Name: Printer Model Number(s): TP-450 Product Description: Printer We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: July. 22, 2021 Name:

William Hawkins Title:

President Company:

AMBIR TECHNOLOGY INC.

AMBIR TECHNOLOGY INC.

Office of Engineering Technology

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

USA

Date: July. 22, 2021

Subject; Request for Confidentiality

FCC ID: 2AH6G-TP450

To Whom It May Concern,

Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we

are requesting the Commission to withhold the following attachment(s) as confidential

documents from public disclosure indefinitely.

These documents contain detailed system and equipment descriptions and are considered as

proprietary information in operation of the equipment. The public disclosure of these documents

might be harmful to our company and would give competitors an unfair advantage in the market.

Schematic Diagram

Block Diagram

Parts List

Operational Description

It is our understanding that all measurement test reports, FCC ID label format and

correspondence during the certification review process cannot be granted as confidential

documents and this information will be available for public review once the grant of equipment

authorization is issued.

Sincerely,

Signature:

Name: William Hawkins

Title: President