FCC ID: RC6-APL5XX 2x2 11ax WIFI AP

Step 5 Access Point Setup

(1) Open a web browser on your computer. In the address bar of the web browser, enter 192.168.1.254 and enter.

(2) A login screen will appear. By default, the username of the Access Point is admin and the password is admin. Enter the current username and password of the Access Point and then click Login.

(Username: admin, Password: admin)

(3) TThe Access Point User Interface will appear. This device can operate in Access Point operating mode. Model variants Trade Name Model No. Dierence Amigo Technology APL52X 2x2 11ax AP Amigo Technology APL54X 2x2 11ax AP with LTE option (module) FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help. CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF Exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This radio transmitter FCCID: RC6-APL5XX has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List (for APL54X) No. Manufacturer Part No. Antenna Type Max Antenna Gain 1 2 ANJIE ANJIE AELQ2S-W6159 AELQ2S-W6959 Dipole Dipole 4.4 dBi 3.0 dBi Quick Installation Guide Indoor A ccess P oint Step 1 Package Content

(1) Access Point

(2) Power Adapter

(3) Wall Mounting screw kit

(4)Ceiling mounting bracket If you are initiating the APL52X , which is the pure 2x2 11ax DBDC access point, the Package Content included (Illustration) For Wall Mount Installation:

(1)Determine where the mounting plate of Access Point to be placed and mark location on the surface for the two mounting holes. Use the appropriate drill bit to drill two 26mm depth holes in the markings and hammer the bolts into the openings.

(2)Screw the anchors into the holes until they are flush with the wall.

(3)Put mounting plate on the wall to map with hole of anchor then screw the included screws into the anchors.

(4)Place the Access Point against wall fitting throughout the slots of the Access Point. For Ceiling mount Installation:

(1)Slide the ceiling mount base into the slot of the Access Point.

(2)Hold the Access Point with one hand to reach the other hand over the T-Rail sides of the bracket. Then hook the stationary end of the ceiling mount bracket onto the T-Rail.

(C) DC Power Adapter (Plug in from DC Jack)

-Connect the Power Adapter to the DC-IN port of the Access Point and plug the other end into an electrical outlet. Note: The Access Point supports both IEEE 802.3at PoE (Power over Ethernet) or the included power adapter. You may use either one as the power source. DO NOT use both at the same time. Step 4 IP Address Configuration

(1)Once your computer is on, ensure that your TCP/IP is enabled. Open Network Connections and then click Local Area Connection. Select Internet Protocol Version 4 (TCP/IPv4).

(2)If your computer is already on a network, ensure that you have set it to a Static IP Address on the interface.

(Example: 192.168.1.2 , the Subnet Mask address as 255.255.255.0. and Default Gateway is 192.168.1.254 )

(1)Connect one end of the Ethernet cable into the LAN1 port of the Access Point and the other end to the Ethernet port on the computer.

(2)Plug in power source by different ways that depends on user setup environment

(A) PoE Switch (Plug in from LAN1 Port) S w i t c h

(B) PoE Injector (Plug in from LAN1 Port) I n j e c t o r Step 2 Mounting Kits Installation Step 3 Connecting the Device for Configuration

Step 5 Access Point Setup

(1) Open a web browser on your computer. In the address bar of the web browser, enter 192.168.1.254 and enter. Model variants Trade Name Model No. Dierence Amigo Technology APL52X 2x2 11ax AP Amigo Technology APL54X 2x2 11ax AP with LTE option (module)

(2) A login screen will appear. By default, the username of the Access Point is admin and the password is admin. Enter the current username and password of the Access Point and then click Login.

(Username: admin, Password: admin)

(3) TThe Access Point User Interface will appear. This device can operate in Access Point operating mode. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help. CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF Exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This radio transmitter FCCID: RC6-APL5XX has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List (for APL54X) No. Manufacturer Part No. Antenna Type Max Antenna Gain 1 2 ANJIE ANJIE AELQ2S-W6159 AELQ2S-W6959 Dipole Dipole 4.4 dBi 3.0 dBi Quick Installation Guide Indoor A ccess P oint Step 1 Package Content

(1) Access Point

(2) Power Adapter

(3) Wall Mounting screw kit

(4)Ceiling mounting bracket

(5)External Antenna If you are initiating the APL54X which is the 2x2 11ax DBDC access point with the LTE option, the Package Content included (Illustration) For Wall Mount Installation:

(1)Determine where the mounting plate of Access Point to be placed and mark location on the surface for the two mounting holes. Use the appropriate drill bit to drill two 26mm depth holes in the markings and hammer the bolts into the openings.

(2)Screw the anchors into the holes until they are flush with the wall.

(3)Put mounting plate on the wall to map with hole of anchor then screw the included screws into the anchors.

(4)Place the Access Point against wall fitting throughout the slots of the Access Point. For Ceiling mount Installation:

(1)Slide the ceiling mount base into the slot of the Access Point.

(2)Hold the Access Point with one hand to reach the other hand over the T-Rail sides of the bracket. Then hook the stationary end of the ceiling mount bracket onto the T-Rail.

(C) DC Power Adapter (Plug in from DC Jack)

-Connect the Power Adapter to the DC-IN port of the Access Point and plug the other end into an electrical outlet. Note: The Access Point supports both IEEE 802.3at PoE (Power over Ethernet) or the included power adapter. You may use either one as the power source. DO NOT use both at the same time. Step 4 IP Address Configuration

(1)Once your computer is on, ensure that your TCP/IP is enabled. Open Network Connections and then click Local Area Connection. Select Internet Protocol Version 4 (TCP/IPv4).

(2)If your computer is already on a network, ensure that you have set it to a Static IP Address on the interface.

(Example: 192.168.1.2 , the Subnet Mask address as 255.255.255.0. and Default Gateway is 192.168.1.254 )

(1)Connect one end of the Ethernet cable into the LAN1 port of the Access Point and the other end to the Ethernet port on the computer.

(2)Plug in power source by different ways that depends on user setup environment

(A) PoE Switch (Plug in from LAN1 Port) S w i t c h

(B) PoE Injector (Plug in from LAN1 Port) I n j e c t o r Step 2 Mounting Kits Installation Step 3 Connecting the Device for Configuration

CustomerAmigo APL52X Part NO. Part Name Device Label Description Dimention 74.5*44.5mm C2mm Material Print Color Black Version :1.0 Remark Unitsmm Drawer 50+PET Crystal Tolerance Date 0.5 mm 2020.03.29 Font: Arial Blod APL52X Font: Arial Code 128A S/N PH52MY H00001 MAC AABBCC002233 INPUT 12V 2A FCC ID:RC6-APL5XX 44.5mm This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made in Taiwan 74.5mm 1:1 S/N : 12 CODE 128A PL52 M Y H000 0 1 Amigo 2019 = J 2020 = K 2021 = L 2022 = M 2023 = N APL52X S/N PH52MY H00001 LAN MAC AABBCC002233 INPUT 12V 2A FCC ID:RC6-APL5XX This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made in Taiwan Label Location (Bottom Case) 40%

MCA LAN MAC NIC0 Version :1.0

CustomerAmigo APL54X Part NO. Part Name Device Label Description Dimention 74.5*44.5mm C2mm Material Print Color Black Version :1.0 Remark Unitsmm Drawer 50+PET Crystal Tolerance Date 0.5 mm 2020.03.29 Font: Arial Blod APL54X Font: Arial Code 128A S/N PH54MY H00001 MAC AABBCC002233 INPUT 12V 2A FCC ID:RC6-APL5XX Contains FCC ID: N7NEM75 44.5mm This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made in Taiwan 74.5mm 1:1 S/N : 12 CODE 128A PL54 M Y H000 0 1 Amigo 2019 = J 2020 = K 2021 = L 2022 = M 2023 = N APL54X S/N PH54MY H00001 LAN MAC INPUT AABBCC002233 12V 2A FCC ID:RC6-APL5XX Contains FCC ID: N7NEM75 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made in Taiwan Label Location (Bottom Case) 40%

MCA LAN MAC NIC0 Version :1.0

Amigo Technology Inc. No.82, Gongye 2nd Rd., Annan Dist., Tainan City 709, Taiwan Date: June 28, 2021 File Name

(APL52X, APL54X)BlkDia

(APL52X, APL54X)Schem

(APL52X, APL54X)OpDes Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: RC6-APL5XX Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ______________________ Signatory Jay Kung, R&D AVP jay.kung@amigo.com.tw Rev 11/20/07

Amigo Technology Inc. No.82, Gongye 2nd Rd., Annan Dist., Tainan City 709, Taiwan DeclarationofModelNames Date:June28,2021 ToWhomItMayConcern:

We,theundersigned,herebyconfirmthatdeviceFCCID:RC6APL5XXhavetwomodelnames thatmodelnameofAPL52X,APL54XisidenticalinRFhardwareandsoftwaredesign. Thesemodelnameshavefollowingdifference:

ModelNumber ContainacertifiedWWANModule APL52X APL54X Nocontainmodule. ContainWWANmodulewhichFCCID:N7NEM75(Sierra/EM7565). ThedeviceaccessoryhastwodetachableWWANantennasthatpartnumberare AELQ2SW6159andAELQ2SW6959. Inadditiontotheaboveinformation,thesedevicesareidentical. Sincerely, Signature:___________________________ FCCgranteecontactpersoninformation. Name:JayKung TEL:+886226093434 Email:jay.kung@amigo.com.tw

Amigo Technology Inc. No.82, Gongye 2nd Rd., Annan Dist., Tainan City 709, Taiwan Louis Hsu DEKRA Testing and Certification Co., Ltd. No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township Hsinchu County 31061 Taiwan, R.O.C. Amigo Technology Inc. No.82, Gongye 2nd Rd., Annan Dist. Tainan City 709 Taiwan Declaration of Authorization We Name:

Address:

City:

Country:

Declare that:

Name Representative of agent:

Agent Company name:

Address:

City:

Country is authorized to apply for FCC Certification of the following product(s):

Product description: 2x2 11ax WIFI AP Type designation: APL52X, APL54X Amigo Technology Trademark:

on our behalf. ______________________ Signatory Jay Kung, R&D AVP jay.kung@amigo.com.tw