| all | frequencies |
|
|
exhibits | applications |
|---|---|---|---|---|---|
| manuals | |||||
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
Ins6tallation Instruction | Users Manual | 108.47 KiB | ||||
| 1 |
|
User Manual | Users Manual | 1.93 MiB | ||||
| 1 | External Photos | |||||||
| 1 | Internal Photos | |||||||
| 1 | ID Label/Location Info | |||||||
| 1 | RF Exposure Info | |||||||
| 1 | Cover Letter(s) | |||||||
| 1 | Test Report | |||||||
| 1 | Test Report | |||||||
| 1 | Test Setup Photos |
| 1 | Ins6tallation Instruction | Users Manual | 108.47 KiB |
Installation Instruction The Remote Unit, Extension Unit or Master Unit has to be mounted by proffessionel / special trained installer. 1.1. MECHANICAL INSTALLATION 1.1.1. General Read the health and safety warnings in section 1.3. 1. Do not install the unit in a way or at a place where the specifications outlined in the Environmental and Safety Specifications leaflet of the supplier are not met. 2. It is recommended only to use the mounting hardware delivered by the supplier. If different mounting hardware is used, the specifications for stationary use of the Remote Unit must not be exceeded. Note: Exceeding the specified load limits may cause the loss of warranty!
3. The unit is considerably heavy. Make sure that a suitable mounting surface is used. Ensure there is adequate manpower to handle the weight of the system. 4. Due to power dissipation, the Remote Unit may reach a very high temperature. Ensure sufficient airflow for ventilation as specified in the individual mounting procedures. 5. When connecting and mounting the cables (RF, optical, mains, ...) ensure no water can penetrate into the unit through these cables. 6. Also observe all additional rules or restrictions regarding mounting that depend on the type of Remote Unit. Install the unit vertically with the fan unit at the top. A maximum tilt angle of 25 from a vertical position must be kept, as in the following illustrations:
7. A spacing of 40 mm (1.58 inch) around the unit is required. 8. To ensure sufficient airflow when mounting the unit in enclosed spaces, two lid openings (one for the air inlet and the other for the air outlet) have to be provided. Do not block these air inlets and outlets when mounting the Remote Unit. The size of each opening must equal at least 12 x 12 cm (144 cm2). Make sure, too, there is no thermal short circuit between the air inlet and air outlet. If any different or additional mounting material is used, ensure that the mounting remains as safe as the mounting designed by the manufacturer. Ensure that the static and dynamic strengths are adequate for the environmental conditions of the site. The mounting itself must not vibrate, swing or move in any way that might cause damage to the Remote Unit. Specified torques have to be observed for certain mounting procedures according to the following table:
Type Thread Specified torques Hex
(aluminium) nuts PG 29 M 8 M 4 27 Nm 2.3 Nm 27 Nm 3.75 Nm 10 Nm table Specified torques
(plastic) PG 13.5 M 4 3.3 Nm Tallow-drop Spacing screws bolts M 8 PG PG Note: To avoid damage when mounting the unit, always make sure that the M8 washers
(DIN9021 or DIN125 depending on the mounting kit) are placed behind and in front of the mounting drillings of the unit. The mounting procedures for a stand-alone Remote Unit without optional accessories are described and illustrated in the following sections. For further information regarding special mounting procedures including mounting of accessory equipment, please see separate manual. 1.2. ELECTRICAL INSTALLATION 1.2.1. General Read the health and safety warnings in section 1.3. 1. This unit contains dangerous voltages. Loss of life, severe personal injury or property damage can be the result if the instructions contained in this manual are not followed. 2. Ground the unit before connecting power supply. A grounding bolt is provided on the cabinet to connect the ground-bonding cable. 3. Although the Remote Unit is internally protected against over-voltage, it is strongly recommended to earth the antenna cables close to the antenna connectors of the Remote Unit for protection against atmospheric discharge. In areas with strong lightning it is highly recommended to insert additional lightning protection. 4. If the mains connector of the Remote Unit is not easily accessible, a disconnect device in the mains circuit must be provided within easy reach. 5. Before connecting or disconnecting the mains connector at the Remote Unit, ensure that mains supply is disconnected. 6. Make sure that an appropriate circuit breaker and an over-current limiting device are connected between mains and Remote Unit. 7. A connection of mains supply to a power socket requires the power socket to be nearby the Remote Unit. 8. Incorrectly wired connections can destroy electrical and electronic components. 9. To avoid corrosion at the connectors caused by electrochemical processes, the material of the cable connectors must not cause a higher potential difference than 0.6 V (see electrochemical contact series). 10. Use an appropriate torque wrench for the coupling torque of N-type connectors (2 N-m / 20 in lb), with 13/16 inch opening to tighten the N-type antenna connectors. For example, use torque wrench of item no. 244379 available from the Andrew e-catalog. Do NOT use your hands or any other tool
(e.g. a pair of pliers)! This might cause damage to the connector and lead to a malfunction of the Remote Unit. 11. Use a voltage limiting device for unstabilized electric networks that frequently generate spikes. 12. The unit complies with the surge requirement according to EN 61000-4-5 (fine protection); however, it is recommended to install an additional medium (via local supply connection) and/or coarse protection (external surge protection), depending on the individual application, in order to avoid damage caused by overcurrent. 13. Observe the labels on the front panels before connecting or disconnecting any cables. 1.3. HEALTH AND SAFETY WARNINGS 1. Only suitably qualified personnel is allowed to work on this unit and only after becoming familiar with all safety notices, installation, operation and maintenance procedures contained in this manual. 2. Read and obey all the warning labels attached to the unit. Make sure that the warning labels are kept in a legible condition and replace any missing or damaged labels. 3. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 4. Keep operating instructions within easy reach and make them available to all users. 5. It is the responsibility of the network provider to implement prevention measures to avoid health hazards which may be associated to radiation from the antenna(s) connected to the unit. 6. Note for a Class A digital device or peripheral:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 7. Make sure, access is restricted to qualified personnel. 8. Only licence holders for the respective frequency range are allowed to operate this unit. 9. Corresponding local particularities and regulations must be observed. For national deviations please refer to the respective documents included in the manual CD delivered. 10. Use this equipment only for the purpose specified by the manufacturer. Do not carry out any modifications or fit any spare parts which are not sold or recommended by the manufacturer. This could cause fires, electric shock or other injuries. 11. Due to power dissipation, the repeater may reach a very high temperature. Do not operate this equipment on or close to flammable materials. 12. Before opening the unit, disconnect mains. 13. ESD precautions must be observed! Before commencing maintenance work, use the available grounding system to connect ESD protection measures. 14. This unit complies with European standard EN60950. 15. Make sure the repeater settings are according to the intended use (see also product information of manufacturer) and regulatory requirements are met. 16. Although the repeater is internally protected against overvoltage, it is strongly recommended to earth the antenna cables close to the repeaters antenna connectors for protection against atmospheric discharge. 17. Laser radiation! Do not stare into the beam; do not view it directly or with optical instruments.
| 1 | User Manual | Users Manual | 1.93 MiB |
Optical Remote Unit ION-M7P/17P Subassemblies
(M-cabinet) Manual MF0145A7A Manual for ION-M7P/17P (M-cab)
& Subassemblies Copyright 2012 CommScope, Inc. All rights reserved. CommScope Solutions is a trademark of CommScope, Inc. All information contained in this manual has been revised thoroughly. Yet CommScope Solutions accepts no liability for any omissions or faults. CommScope Solutions reserves the right to change all hardware and software characteristics without notice. Names of products mentioned herein are used for identification purposes only and may be trademarks and / or registered trademarks of their respective companies. No parts of this publication may be reproduced, stored in a retrieval system, transmitted in any form or by any means, electronical, mechanical photocopying, recording or otherwise, without prior written permission of the publisher. Andrew Wireless Systems GmbH, 10-May-2012 Page 2 MF0145A7A_uc_FCC_modif.doc TABLE OF CONTENTS 1. GENERAL 1.1. 1.2. 1.3. 1.4. USED ABBREVIATIONS HEALTH AND SAFETY WARNINGS ABOUT COMMSCOPE SOLUTIONS INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT 2. INTRODUCTION 2.1. 2.2. PURPOSE THE ION-M7P/17P (INTELLIGENT OPTICAL NETWORK; MMR) 3. FUNCTIONAL DESCRIPTION 3.1. 3.1.1. 3.1.2. COMPONENTS OF THE ION-M7P/17P REMOTE UNIT Fan-Protection Kit Accessories 4. COMMISSIONING 4.1. 4.1.1. 4.1.2. 4.1.3. 4.1.4. 4.2. 4.2.1. 4.2.2. 4.2.3. 4.2.4. 4.3. 4.4. 4.4.1. 4.4.2. 4.5. MECHANICAL INSTALLATION General Wall-Mounting Procedure Pole-Mounting Procedure Mounting of Fan Protection ELECTRICAL INSTALLATION General Connections Grounding Power Connection CONNECTION OF THE ANTENNA CABLES OPTICAL FIBER CABLE CONNECTION RULES Protective Plug Protective-Tube Kit COMMISSIONING 5. ALARMS BITE AND ALARMS HANDLING OF ALARMS 5.1. 5.2. 7 7 8 10 11 14 14 14 16 16 16 16 17 17 17 19 20 22 23 23 24 25 25 26 27 28 30 32 35 35 35 Page 3 Manual for ION-M7P/17P (M-cab)
& Subassemblies ALARM STATUS STATUS LED ALARMS 5.3. 5.4. 5.5. 5.6. EXTERNAL ALARM INPUTS AND OUTPUTS TROUBLESHOOTING 6. MAINTENANCE 6.1. 6.2. 6.3. GENERAL REPLACING THE FAN UNIT CLEANING THE HEAT SINK 7. APPENDIX 7.1. 7.2. 7.2.1. 7.2.2. 7.2.3. 7.3. ILLUSTRATIONS SPECIFICATIONS Electrical Specifications Mechanical Specifications Environmental and Safety Specifications SPARE PARTS INDEX 8. 35 35 36 38 39 39 40 42 43 43 44 44 44 44 45 46 Page 4 MF0145A7A_uc_FCC_modif.doc FIGURES AND TABLES figure 4-1 Wall mounting, (metric dimensions).......................................................... 19 figure 4-2 Pole-mounting kit...................................................................................... 20 figure 4-3 Pole mounting (metric dimensions) .......................................................... 21 figure 4-4 Mounting procedure for fan protection, (metric dimensions)..................... 22 figure 4-5 Connector flange of ION-M7P/17P........................................................... 24 figure 4-6 Grounding bolt with loosened hex nut ...................................................... 25 figure 4-7 Grounding bolt, schematic view................................................................ 25 figure 4-8 AC mains plug .......................................................................................... 26 figure 4-9 Protective-plug assembly ......................................................................... 28 figure 4-10 Tube-kit installation................................................................................. 31 figure 5-1 Flange connector, 5 poles ........................................................................ 36 figure 5-2 Flange connector, 7 poles ........................................................................ 36 figure 5-3 Alarm inputs and outputs, standard.......................................................... 37 figure 7-1 Installation drawing................................................................................... 43 table 1-1 List of international contact addresses....................................................... 13 table 4-1 Specified torques....................................................................................... 18 table 5-1 Status LED alarms..................................................................................... 36 Page 5 Manual for ION-M7P/17P (M-cab)
& Subassemblies For your notes:
Page 6 MF0145A7A_uc_FCC_modif.doc 1. GENERAL Manual for ION-M7P/17P (M-cab)
& Subassemblies 1.1. USED ABBREVIATIONS 3GPP AC/DC AIMOS ALC BITE BTS CE CD CPD DL DoC EDGE EN EP ESD ETS EU GSM GND GUI ICP3 ID No ION IP ISO LED LMT LTE MIMO MS MU NF OTRx PDU PG PIM R&TTE Rev RF RU RX SNMP TS TX UL UMTS UPS VSWR WCDMA WDM 3rd Generation Partnership Project Alternating current / Direct Current Andrew Integrated Management and Operating System Automatic Level Control Built-In Test Equipment Base Transceiver Station
"Conformit Europenne" ("European Conformity") Compact Disk Channel Power Detection Downlink Declaration of Conformity Enhanced Data Rates for GSM Evolution European Norm Extension Port Electrostatic Discharge European Telecommunication Standard Extension Unit Global System for Mobile Communication Ground Graphical User Interface Intercept Point 3rd order Identification Number Intelligent Optical Network Ingress Protection International Organization for Standardization Light Emitting Diode Local Maintenance Terminal Long Term Evolution Multiple Input Multiple Output Mobile Station Main Unit Noise Figure Optical Transceiver = SRMU (Subrack Master Unit) Power Distribution Unit Packing Gland Passive Intermodulation Radio & Telecommunications Terminal Equipment Revision Radio Frequency Remote Unit Receiver Simple Network Management Protocol Technical Specification Transmitter Uplink Universal Mobile Telecommunication System Uninterruptible Power Supply Voltage Standing Wave Ratio Wideband Code Division Multiple Access Wavelength Division Multiplex Page 7 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 1.2. HEALTH AND SAFETY WARNINGS 1. Only suitably qualified personnel is allowed to work on this unit and only after becoming familiar with all safety notices, installation, operation and maintenance procedures contained in this manual. 2. Read and obey all the warning labels attached to the unit. Make sure that the warning labels are kept in a legible condition and replace any missing or damaged labels. 3. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 4. Keep operating instructions within easy reach and make them available to all users. 5. It is the responsibility of the network provider to implement prevention measures to avoid health hazards which may be associated to radiation from the antenna(s) connected to the unit. 6. Note for a Class A digital device or peripheral:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 7. Make sure, access is restricted to qualified personnel. 8. Only licence holders for the respective frequency range are allowed to operate this unit. 9. Corresponding local particularities and regulations must be observed. For national deviations please refer to the respective documents included in the manual CD delivered. 10. Use this equipment only for the purpose specified by the manufacturer. Do not carry out any modifications or fit any spare parts which are not sold or recommended by the manufacturer. This could cause fires, electric shock or other injuries. 11. Due to power dissipation, the repeater may reach a very high temperature. Do not operate this equipment on or close to flammable materials. Page 8 MF0145A7A_uc_FCC_modif.doc 12. Before opening the unit, disconnect mains. Manual for ION-M7P/17P (M-cab)
& Subassemblies 13. ESD precautions must be observed! Before commencing maintenance work, use the available grounding system to connect ESD protection measures. 14. This unit complies with European standard EN60950. 15. Make sure the repeater settings are according to the intended use (see also product information of manufacturer) and regulatory requirements are met. 16. Although the repeater is internally protected against overvoltage, it is strongly recommended to earth the antenna cables close to the repeaters antenna connectors for protection against atmospheric discharge. 17. Laser radiation! Do not stare into the beam; do not view it directly or with optical instruments. Page 9 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 1.3. ABOUT COMMSCOPE SOLUTIONS CommScope Solutions is the foremost supplier of one-stop, end-to-end radio frequency (RF) solutions. Our products are complete solutions for wireless infrastructure from top-of-the-tower base station antennas to cable systems and cabinets, RF site solutions, signal distribution, and network optimization. CommScope Solutions has global engineering and manufacturing facilities. In addition, it maintains field engineering offices throughout the world. Andrew Wireless Systems GmbH based in Buchdorf/ Germany, which is part of CommScope Solutions, is a leading manufacturer of coverage equipment for mobile radio networks, specializing in high performance, RF and optical repeaters. Our optical distributed networks and RF repeater systems provide coverage and capacity solution for wireless networks in both indoor installations and outdoor environments, e.g. tunnels, subways, in-trains, airport buildings, stadiums, skyscrapers, shopping malls, hotels and conference rooms. Andrew Wireless Systems GmbH operates a quality management system in compliance with the requirements of ISO 9001 and TL 9000. All equipment is manufactured using highly reliable material. To maintain highest quality of the products, comprehensive quality monitoring is conducted at all fabrication stages. Finished products leave the factory only after a thorough final acceptance test, accompanied by a test certificate guaranteeing optimal operation. Note: Exceptions of and national deviations from this intended use may be possible. To observe corresponding local particularities and regulations, please refer to the respective documents (also in national language) which are included in the manual CD delivered. To make the most of this product, we recommend you carefully read the instructions in this manual and commission the system only according to these instructions. For technical assistance and support, please also contact the local office or CommScope Solutions directly at one of the addresses listed in the following chapter. Page 10 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 1.4. INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT Americas:
Canada United States CommScope Solutions Canada 505 Consumers Road, Suite 803 Toronto M2J 4V8 Canada Mail Phone +1-905-878-3457 (Office)
+1-416-721-5058 (Cell) Fax
+1-905-878-3297 E-mail Peter.Masih@commScope.com, wisupport.us@commScope.com Andrew LLC, A CommScope Company Mail 620 North Greenfield Parkway Garner, NC 27529 U.S.A. Phone +1-888-297-6433 Fax
+1-919-329-8950 E-mail wisupport.us@commScope.com Caribbean & South American Region
(CALA) Caribbean (CALA) & Central American Region CommScope Cabos do Brasil Ltda. CommScope Mexico S.A. de C.V. CALA Tech Support for Distributed Coverage & Capacity Solutions
(DCCS) products:
Rua Guaporanga, 49 Praa Seca Rio de Janeiro RJ ZIP: 21320-180 Brazil
+1-815-546-7154 (Cell)
+55-15-9104-7722 (Office)
+ 55-15-2102-4001 wisupport@commScope.com Mail CALA Tech Support for Distributed Coverage & Capacity Solutions
(DCCS) products:
Av. Insurgentes Sur 688, Piso 6 Col. Del Valle, CP: 03100 Mexico City Mexico Phone +52-1-55-5419-5260 (Cell)
+52-55-1346-1900 (Office)
+52-55-1346-1901 Fax E-mail wisupport@commScope.com APAC Countries:
Mail Phone Fax E-mail China, India and Rest of Asia Australia & New Zealand Andrew International Corporation Andrew Corporation (Australia) Pty Ltd. Mail Room 915, 9/F Chevalier Commercial Centre 8 Wang Hoi Rd Kowloon Bay Hong Kong Phone +852-3106-6100 Fax
+852-2751-7800 Mail Unit 1 153 Barry Road Campbellfield VIC 3061 Australia Phone +613-9300-7969 Fax
+613-9357-9110 E-mail wisupport.China@commScope.com E-mail wisupport.Australia@commScope.com Page 11 MF0145A7A_uc_FCC_modif.doc Mail Manual for ION-M7P/17P (M-cab)
& Subassemblies Europe:
United Kingdom Andrew Wireless Systems UK Ltd Scandinavia Andrew Norway (AMNW) Unit 15, Ilex Building Mulberry Business Park Fishponds Road Wokingham Berkshire RG41 2GY England Phone +44-1189-366-792 Fax
+44-1189-366-773 E-mail wisupport.uk@commScope.com Germany Andrew Wireless Systems GmbH Mail Industriering 10 86675 Buchdorf Germany
+49-9099-69-930 Phone +49-9099-69-0 Fax E-mail wisupport@commScope.com Austria Mail P.O. Box 3066 Osloveien 10 Hoenefoss 3501 Norway Phone Fax E-mail
+ 47 32-12-3530
+ 47 32-12-3531 wisupport@commScope.com Mail Phone Fax E-mail France CommScope France Immeuble Le Lavoisier 4, Place des Vosges 92052 Courbevoie France
+33-1 82 97 04 00
+33-1 47 89 45 25 wisupport@commScope.com Switzerland Andrew Wireless Systems (Austria) GmbH Andrew Wireless Systems AG Mail Weglgasse 10 2320 Wien-Schwechat Austria Phone +43-1706-39-99-10 Fax
+43-1706-39-99-9 E-mail wisupport.austria@commScope.com Mail Phone Fax E-mail Tiergartenweg 1 CH-4710 Balsthal Switzerland
+41-62-386-1260
+41-62-386-1261 wisupport.ch@commScope.com Italy Iberia Region - Spain & Portugal CommScope Italy S.r.l., Faenza, Italy Mail Via Mengolina, 20 48018 Faenza (RA) Italy
+39-0546-697111
+39-0546-682768 Phone Fax E-mail wisupport.italia@commScope.com Mail Andrew Espaa S.A. A CommScope Company Avda. de Europa, 4 - 2 pta. Parque Empresarial de la Moraleja Alcobendas, Madrid 28108 Spain
+34-91-745-20 40
+34-91-661-87 02 Phone Fax E-mail wisupport.iberia@commScope.com Page 12 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies Czech Republic CommScope Solutions Czech Republic C-Com, spol. s r.o Mail U Moru 888 53006 Pardubice Czech Republic Phone +49 871 9659171 (Office)
+49 171 4001166 (Mobile) Fax
+49 871 9659172 E-mail wisupport@commScope.com Africa & Middle East:
Middle East & North Africa South Africa CommScope Solutions International Inc.
(Branch) PO Box 48 78 22 Unit 3206, Floor 32, Jumeirah Business Center 5, Jumeirah Lakes Towers, Dubai United Arab Emirates
+971 4 390 09 80
+971 4 390 86 23 Mail Phone Fax Andrew Wireless Solutions Africa (PTY) LTD Mail 11 Commerce Crescent West Eastgate, Sandton PO Box 786117 Sandton 2146 South Africa Phone + 27 11-719-6000 Fax
+ 27 11-444-5393 E-mail wisupport@commScope.com E-mail wisupport@commScope.com table 1-1 List of international contact addresses Page 13 MF0145A7A_uc_FCC_modif.doc 2. INTRODUCTION Manual for ION-M7P/17P (M-cab)
& Subassemblies 2.1. PURPOSE Cellular telephone systems transmit signals in two directions between base transceiver station (BTS) and mobile stations (MS) within the signal coverage area. If weak signal transmissions occur within the coverage area because of indoor applications, topological conditions or distance from the transmitter, extension of the transmission range can be achieved by means of an optical distribution system. Such a system contains an optical Master Unit and several Remote Units. The number of the Remote Units depends on the hardware and software configuration. The Remote Units are connected to the Master Unit with optical links. The optical loss must be less than 10 dB inclusive optical couplers or splitters. The Master Unit is the connection to the base transceiver stations. The configuration of a Master Unit depends on the number of the Remote Units and the frequency range. WDM (Wave Division Multiplex) filters are integrated in the optical modules. For the UL, a wavelength within 1540 nm 1562 nm is used. For the DL, a wavelength of 1310 20 nm is used. The maximum output power for the UL and DL is 5.7 mW. 2.2. THE ION-M7P/17P (INTELLIGENT OPTICAL NETWORK; MMR) The ION-M7P/17P is a multi-band, multi-operator remote unit configuration used in conjunction with a master unit in the ION optical distribution system. This system transports up to two frequency bands simultaneously (700 MHz and 1700/2100 MHz), providing a cost-effective solution for distributing capacity from one or more base stations. The ION system transports signals on the RF layer in a very cost-effective manner enabling multiple operators to use multiple technologies and move their signals simultaneously from a cluster of base station to a number of remote locations over the same fiber. The ION-M optical distribution system is a cost-effective coverage solution for dense urban areas, tunnels, subways, airports, convention centers, high-rise buildings and other locations where physical structures increase path loss. The combination of these units gives maximum flexibility while providing a scalable solution. The system is optimized for CDMA, WCDMA, HSPA+, and OFDM modulation in the 700 MHz and 1700/2100 MHz bands. Furthermore it is provisioned for future modulation and frequency bands. Page 14 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies The ION can be easily set-up and supervised from a graphical user interface (GUI). Remote units are commissioned through the use of built-in test equipment. An auto levelling function compensates for the optical link loss making installation easy and quick. The entire system can be monitored remotely by the Andrew OMC. This platform uses SNMP protocol and is compliant to X.733 standard. Should a sophisticated interface not be required, the master unit can be directly connected to the alarm interface of a base station via its contact relay. Features at a glance Reduced visual impact form factor Optimized power consumption Efficient, high power amplifier Multi-operator support Complete operations and management system for configuration and alarming OMC with SNMP according to X.733 standard 3GPP TS25.143/TS25.106/36.143/TS36.106 and 3GPP2C.S0051-0 compliant Single fiber for multiple bands and multiple remotes Easy installation and commissioning Page 15 MF0145A7A_uc_FCC_modif.doc 3. FUNCTIONAL DESCRIPTION Manual for ION-M7P/17P (M-cab)
& Subassemblies 3.1. COMPONENTS OF THE ION-M7P/17P REMOTE UNIT 3.1.1. Fan-Protection Kit In order to protect the fan unit (e.g. against rain), a protective cover to be mounted over the air inlet is delivered with the unit. For more details see section 4.1.4 Mounting of Fan Protection. Mounting of the fan-protection kit is only mandatory for outdoor applications, however, not mandatory for indoor applications. 3.1.2. Accessories For the accessories available for the Remote Unit, e.g. overcoat housing, connecting box or iso-trafo kit, a separate manual is available. Page 16 MF0145A7A_uc_FCC_modif.doc 4. COMMISSIONING 4.1. MECHANICAL INSTALLATION Manual for ION-M7P/17P (M-cab)
& Subassemblies 4.1.1. General Read the health and safety warnings in section 1.2 Health and Safety Warnings. 1. Do not install the unit in a way or at a place where the specifications outlined in the Environmental and Safety Specifications leaflet of the supplier are not met. 2. It is recommended only to use the mounting hardware delivered by the supplier. If different mounting hardware is used, the specifications for stationary use of the Remote Unit must not be exceeded. Note: Exceeding the specified load limits may cause the loss of warranty!
3. The unit is considerably heavy. Make sure that a suitable mounting surface is used. Ensure there is adequate manpower to handle the weight of the system. 4. Due to power dissipation, the Remote Unit may reach a very high temperature. Ensure sufficient airflow for ventilation as specified in the individual mounting procedures. 5. When connecting and mounting the cables (RF, optical, mains, ...) ensure no water can penetrate into the unit through these cables. 6. Also observe all additional rules or restrictions regarding mounting that depend on the type of Remote Unit. For details refer to chapter 7.2.2 Mechanical Specification. Install the unit vertically with the fan unit at the top. A maximum tilt angle of 25 from a vertical position must be kept, as in the following illustrations:
Page 17 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 7. A spacing of 40 mm (1.58 inch) around the unit is required. 8. To ensure sufficient airflow when mounting the unit in enclosed spaces, two lid openings (one for the air inlet and the other for the air outlet) have to be provided. Do not block these air inlets and outlets when mounting the Remote Unit. The size of each opening must equal at least 12 x 12 cm (144 cm2). Make sure, too, there is no thermal short circuit between the air inlet and air outlet. If any different or additional mounting material is used, ensure that the mounting remains as safe as the mounting designed by the manufacturer. Ensure that the static and dynamic strengths are adequate for the environmental conditions of the site. The mounting itself must not vibrate, swing or move in any way that might cause damage to the Remote Unit. Specified torques have to be observed for certain mounting procedures according to the following table:
Type Thread Specified torques Hex nuts
(plastic) M 8 M 4 PG 13.5 PG 29 27 Nm 2.3 Nm 27 Nm 3.75 Nm 10 Nm M 4 3.3 Nm Tallow-drop
(aluminium) Spacing screws bolts M 8 PG PG table 4-1 Specified torques Note: To avoid damage when mounting the unit, always make sure that the M8 washers (DIN9021 or DIN125 depending on the mounting kit) are placed behind and in front of the mounting drillings of the unit. The mounting procedures for a stand-alone Remote Unit without optional accessories are described and illustrated in the following sections. For further information regarding special mounting procedures including mounting of accessory equipment, please see separate manual. Page 18 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 4.1.2. Wall-Mounting Procedure Check the suitability of the wall-mounting kit and the wall. Wall mounting with active cooling kit 4.0 0.50 4 122 0.50 80 0.50 9 18 0 0 1
. 6 9 7 Mark the position of the drilling holes (for measurements refer to figure 4-1 Wall mounting). Drill four holes at the marked positions and insert dowels *. Use a cap nut or lock nut to screw the four dowel screws into the dowels and put the distance tubes over the screws. Hang the mounting brackets of the Remote Unit into the screws, and fasten them immediately using the washers and nuts. Ensure that there is free access to the electrical connections as well as to the cabinet. The approved bending radius of the connected cables must not be exceeded. figure 4-1 Wall mounting, (metric dimensions) Mains supply G0946Z0
* The dowels are not part of the delivery since the suitable type depends on the on-site conditions
(material of wall). Therefore, use dowels that are appropriate for the mounting surface. Page 19 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 4.1.3. Pole-Mounting Procedure Standard mounting hardware cannot be used to mount the Remote Unit to a pole, a column or other similar structures. Additional hardware must be used for this type of installation. Such a pole-mounting kit could include two threaded rods M8, two U-beams and mounting material like bolts and nuts. figure 4-2 Pole-mounting kit Use the screw bands to fasten the two U-beams to the pole as illustrated in figure 4-3 Pole mounting. Note: When fastening the U-beams make sure that they are installed congruently and not at an angle to each other. To determine the distance between the beams refer to 4.1.2 Wall-Mounting Procedure for measurements. Hang the mounting brackets of the Remote Unit into the threaded bolts of the U-beam, and fasten them immediately using the washers and nuts. Ensure that there is free access to the electrical connections as well as to the cabinet. The approved bending radius of the connected cables must not be exceeded. Page 20 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies Lock for folding screw band ES 119 TESPA screw band, stainless, 11 mm Optical Remote Unit Washer DIN 125 Form B 8.0 Lock washer for M8.0 DIN 127 A2 Form B Hexagon nut M8 DIN 934 1 4 0 Pole 0 4 Pole Pole-mounting bracket figure 4-3 Pole mounting (metric dimensions) G0764M6 Page 21 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 4.1.4. Mounting of Fan Protection Since the fan protection is required for the outdoor usage of a stand-alone Remote Unit, the mounting of this optional equipment is also described in this manual. To install the protective cover of the fan protection kit, first unscrew the four screws with the respective lock washers from the cover of the air inlet of the Remote Unit, and instead, screw in the four spacing bolts M4.0x30 with the four lock washers M4.0 DIN125 that are part of the fan protection kit. Place the protective cover into the right position by fitting its four bore holes over the spacing bolts and fasten it using the original lock washers and screws of the Remote Unit. (These lock washers and screws are also part of the fan protection kit and can be used as spare parts in case of loss.) remove the screw and the lock washer!
2x M4.0x8 fillister-head screws remove the screw and the lock washer!
2x lock washers 2x M4.0x8 fillister-head screws 2x lock washers 2x washers 2x M4.0x8 fillister-head screws AIR STREAM 2x M4.0x30 spacing bolts 1x rain protective cover 2x washers 2x lock washers 2x M4.0x8 fillister-head screws 2x lock washers remove the screw and the lock washer!
2x M4.0x8 fillister-head screws 156 152 171 0 2 figure 4-4 Mounting procedure for fan protection, (metric dimensions) G0496MF Page 22 MF0145A7A_uc_FCC_modif.doc 4.2. ELECTRICAL INSTALLATION Manual for ION-M7P/17P (M-cab)
& Subassemblies 4.2.1. General Read the health and safety warnings in section 1.2 Health and Safety Warnings. 1. This unit contains dangerous voltages. Loss of life, severe personal injury or property damage can be the result if the instructions contained in this manual are not followed. 2. Ground the unit before connecting power supply. A grounding bolt is provided on the cabinet to connect the ground-bonding cable. 3. Although the Remote Unit is internally protected against over-voltage, it is strongly recommended to earth the antenna cables close to the antenna connectors of the Remote Unit for protection against atmospheric discharge. In areas with strong lightning it is highly recommended to insert additional lightning protection. 4. If the mains connector of the Remote Unit is not easily accessible, a disconnect device in the mains circuit must be provided within easy reach. 5. Before connecting or disconnecting the mains connector at the Remote Unit, ensure that mains supply is disconnected. 6. Make sure that an appropriate circuit breaker and an over-current limiting device are connected between mains and Remote Unit. 7. A connection of mains supply to a power socket requires the power socket to be nearby the Remote Unit. 8. Incorrectly wired connections can destroy electrical and electronic components. 9. To avoid corrosion at the connectors caused by electrochemical processes, the material of the cable connectors must not cause a higher potential difference than 0.6 V (see electrochemical contact series). 10. Use an appropriate torque wrench for the coupling torque of N-type connectors
(2 N-m / 20 in lb), with 13/16 inch opening to tighten the N-type antenna connectors. For example, use torque wrench of item no. 244379 available from the Andrew e-catalog. Do NOT use your hands or any other tool (e.g. a pair of pliers)! This might cause damage to the connector and lead to a malfunction of the Remote Unit. 11. Use a voltage limiting device for unstabilized electric networks that frequently generate spikes. Page 23 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 12. The unit complies with the surge requirement according to EN 61000-4-5 (fine protection); however, it is recommended to install an additional medium (via local supply connection) and/or coarse protection
(external surge protection), depending on the individual application, in order to avoid damage caused by overcurrent. 13. Observe the labels on the front panels before connecting or disconnecting any cables. 4.2.2. Connections Status LED N-antenna connector Mobile AWS RS485 connector External alarm input Alarm output Mains connector Page 24 Optical-fibre connector Grounding bolt N-antenna connector Mobile LTE700 figure 4-5 Connector flange of ION-M7P/17P MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 4.2.3. Grounding Grounding must be carried out. Connect an earth-bonding cable to the grounding connection provided at the outside of the Remote Unit (see section 4.2.2 Connections). Do not use the grounding connection to connect external devices. figure 4-6 Grounding bolt with loosened hex nut figure 4-7 Grounding bolt, schematic view After loosening the hex nut, connect the earth-bonding cable between the two washers as illustrated in the figures above. Then, fasten all parts again with the hex nut. 4.2.4. Power Connection Before connecting electrical power to the RU, the system must be grounded as described in the previous section. Mains power must be connected at the mains connector of the unit (see section 4.2.2 Connections). The power supply plug is part of the delivery. The correct wiring of the power supply plug is as follows:
Page 25 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies figure 4-8 AC mains plug For the AC power supply connection, a minimum cross section of 1.5 mm2 is required. Each wire must observe the applicable national regulations regarding loop impedance, voltage drop, and methods of installation. Make sure to connect the correct voltage to the unit. Note: Do not connect or disconnect the power cord at the mains connector while power is on. Turn off mains power * before connecting the power cord at the Remote Unit, then, engage mains again.
* Mains power must be interruptible with an external mains breaker. For the mains breaker, observe the following recommendation:
120 Volt / 20 Amp max. or 240 Volt / 16 Amp, single-phase, 50 / 60 Hz AC service is needed, i.e. the external AC breaker should be 20 Amps max. for 120-Volt service or 16 Amps for 240-
Volt service. 4.3. CONNECTION OF THE ANTENNA CABLES The Remote Unit has N-type antenna connectors. Please refer to section 4.2.2 Connections for its location. Refer to the corresponding documentation of the connector manufacturer for mounting the cable connectors. The bending radius of specifications. Consider the type of cable best suited for the antenna. Remember that a cable with higher loss is less expensive but impairs performance. the antenna cables must remain within the given Page 26 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies Use an appropriate torque wrench for the coupling torque of N-type connectors (2 N-m / 20 in lb), with 13/16 in opening to tighten the N-type antenna connectors. For example, use torque wrench of item no. 244379 available from the Andrew e-catalog. Do NOT use your hands or any other tool (e.g. a pair of pliers)! This might cause damage to the connector and lead to a malfunction of the Remote Unit. Note: Directly connect the base station signal to the Master Unit using a coaxial cable to avoid coupling another signal into the system in the DL direction than the single wanted signal transmitted by the base station. 4.4. OPTICAL FIBER CABLE CONNECTION RULES Optical signals are transmitted by use of optical fibers. The optical fiber is a single-
mode fiber. Type is E9/125 m with the following minimum requirements. Attenuation: <0.36 dB / km @ 1310 nm Dispersion: <3.5 ps / nm km @ 1310 nm Follow the procedure below before connecting the fiber cables to ensure optimized performance. These procedures must be carried out carefully:
1. Remove fiber-optic protective caps. 2. Clean the end of the fiber-optic cable that will be inserted in the optical connectors on the donor interface box with high-grade alcohol and lint-free cotton cleaning swabs.
<0.26 dB / km @ 1550 nm
<18.0 ps / nm km @ 1550 nm
3. Blow out the laser receptacle with clean and dry compressed air to remove any particulate matter. 4. Connect the fiber-optic cables by inserting the cable end into the laser receptacle and aligning the key (on the cable end) with the keyed slot. 5. Measure attenuation and reflection with an appropriate measuring instrument. For pigtails, a total value of < 0.4 dB (measured to a reference plug) can be assumed due to the dead zone of the reflectometer. These measurements must be made with a sufficient length of optical fiber, at the input and output of the device which has to be measured. 6. Do not use any index matching gels or fluids of any kind in these connectors. Gels are intended for laboratory use and attract dirt in the field. Observe the following guidelines when connecting the optical fibers:
Do not bend the fiber-optic cable in a tight radius (< 4 cm) as this may cause cable damage and interrupt transmission. The specified bending radius of the optical fibers must not be exceeded. Page 27 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies The pigtails for the connection between Master and Remote Unit must have a sufficient length. A protection for the feeding into units must be given. System attenuation and attenuation of optical components must be determined. Fiber-cable connectors have to be of the same type (E2000APC) as the connectors used for the unit. The fiber-optic cables are connected to the optical transceiver. Angled connectors are not compatible with straight optical connectors;
non-compatibility of connectors will result in permanent damage to both connectors. Note:
Note:
Care should be taken when connecting and disconnecting fiber-optic cables. Scratches and dust significantly affect system performance and may permanently damage the connector. Always use protective caps on fiber-optic connectors not in use. In general, optical fibers do not need special protective measures. However, protection against environmental influences e.g. rodents and humidity must be considered. 4.4.1. Protective Plug Connection:
A protective plug is provided for the connection of the fibre-optic cables. figure 4-9 Protective-plug assembly Note: Only high-quality connectors must be used for this type of plug. Qualified brands are Diamond or Huber & Suhner. MF0145A7A_uc_FCC_modif.doc Page 28 Manual for ION-M7P/17P (M-cab)
& Subassemblies For plug assembly, observe the following instruction:
1. Pass one or two contacts through the backshell and the clamp ring. 2. Place the contact(s) on the lower insulation body by pushing the groove of the contact into the cavity. If there is only one contact, cavity A must be used. *
3. Then, mount the upper insulation body on the lower insulation body. **
Upper insulation body Cavity B 4. Bring the insulator into the plug. The narrow groove of the insulator must be fitted Cavity A into the stamp of the plug.
To release the contact for disassembling, push the inner snap to the side and pull the contact out.
** To release upper and lower insulation bodies for disassembling, use a small screwdriver and carefully open the snap-connections at the left and the right side of the insulator without damaging them. 5. Fasten the insulator by screwing the backshell tight onto it. Use a spanner with opening 32 the backshell tight (no gap). to screw 6. Place the appropriate seal parts (with one groove for one contact or two grooves for two contacts) over the cable(s) and push the backshell. them into No gap Seals with one groove Page 29 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 7. Bring the plastic ring over the cable(s), push it into the backshell and compress the seals and plastic ring by screwing the clamp ring tight (no gap) using a spanner with opening 20. ***
Screw tight until gap is closed 8. Connect the plug to the optical-fibre connector of the Remote Unit, again by fitting a stamp on the plug into the groove of the connector. 9. To lock the connector, push the black locking ring forward.****
Groove Push forward to lock, pull back to free connection
*** For disassembling, release the clamping ring and remove the seals and the plastic ring first.
**** Locking mechanism: The system of locking the plug is based on a push-pull mechanism. The locking ring has to be pushed forward to lock the connector and pulled back to free the connection. for 4.4.2. Protective-Tube Kit As additional protection type can be supplemented by a special tube kit. To fasten the tube correctly, first unscrew the clamp ring (if already installed) of the original plug kit. Then, proceed according to the following instruction:
this connector the optical fibres, Page 30 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies G1055M0 Protective plug Fiber cable Ring 3/4 Reducer Screw the reducer to the protective plug backshell without any gap!
Coupling Protective tube Place the appropriate seal parts (with) one groove for one contact or two grooves for two contacts) over the cable(s) and push them into the backshell!
Push the fiber-optic cable carefully through the tube until it comes out at the other end. figure 4-10 Tube-kit installation Page 31 MF0145A7A_uc_FCC_modif.doc 4.5. COMMISSIONING Manual for ION-M7P/17P (M-cab)
& Subassemblies Read the health and safety warnings in section 1.2 Health and Safety Warnings. Keep for commissioning:
in mind before continuing these guidelines instructions the to Do not operate the Remote Unit without terminating the antenna connectors. The antenna connectors may be terminated by connecting them to their respective antennas or to a dummy load. Only qualified personnel should carry out the electrical, mechanical, commissioning, and maintenance activities that require the unit to be powered on when open. Do not damage the warranty labels on the devices. The warranty is void if the seals are broken. Ensure that all connections have been performed according to section 4.2.2 Connections. Page 32 MF0145A7A_uc_FCC_modif.doc Manual for Remote Unit Philips screwdriver Mounting kit Spanner, size 13 mm Drilling machine Dowels Screw driver Screw driver Spanner, size 13 mm Grounding cable Spanner 13 mm Alarm kit
(M-cabinet) E2000 APC8 connector Spanner with opening 32 Mains cable Connecting kit Manual for ION-M7P/17P (M-cab)
& Subassemblies Commissioning an ION-M Remote Unit Start Unpack RU, RU accessories and Preperation mounting kit. Mechanical installation Fasten wall or pole mounting kit to wall or pole. Mechanical installation Mount RU to mounting kit, ensure suffient air flow and avoid thermal short circuits. Electrical connections Connect grounding cable and ground the RU. External devices Connect external devices to the external in or alarm out connectors, or to the connecting board inside the RU. RF connection Connect antenna cable to antenna port. Optical connections Mount the optical fibre with E2000 APC8 connector into the connector. Plug the connector into the RU. Electrical connections Connect AC power to the power cable. Ensure there is a circuit breaker between mains and RU. Mains Switch mains power on. G1055Z0 Page 33 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies LED on?
No Check power switch inside RU
(RUs with door). Check mains cabling. Check mains power. Yes LED status Red Orange Internal Error Change power supply (RUs with a door). Reduce environmental temperature. Eliminate thermal short circuit. Disconnect and connect mains. Fans should run. If not, replace the fans at RU. MU: Change amplifier setting at MU controller Yes Yellow LED status Red Green External error Close the door (RUs with a door). Check externally connected devices. Check fibre loss of optical link. Check optical connectors. Clean optical connectors. Check optical output power of corresponding OTRx at master unit. ALC alarm: Decrease DL input power of affected band. VSWR alarm: Check antenna and cable. Green Spare RU available?
No Contact customer service Finished setting up all RUs?
No Yes Proceed to MU to set up the SW Output:
All RUs okay. MF0145A7A_uc_FCC_modif.doc Go to MU Page 34 5. ALARMS Manual for ION-M7P/17P (M-cab)
& Subassemblies 5.1. BITe AND ALARMS The Built-In Test (BITe) concept comprises the monitoring of the power supplies, the power amplifiers and the optical interface. All alarms occurring can be checked via software at the Master Unit. 5.2. HANDLING OF ALARMS A message is transmitted to the Master Unit when the software acknowledges a valid alarm. A new alarm message will not be repeated if the reason for the alarm is cleared or if the alarm continues. A new alarm message will be generated if the alarm is interrupted for at least five seconds after acknowledgement. 5.3. ALARM STATUS Refer to the corresponding software documentation of the Master Unit for details. 5.4. STATUS LED ALARMS For local supervision, a status LED on the connector flange of the Remote Unit gives an indication of possible reasons for alarms. This table shows possible on-site measures that could be checked before referring to the Master Unit alarm list. Status LED Indication Green Alarms No alarm Status ok Door alarm Alarms not directly related to RU:
External alarms Check externally connected devices. Close the door (RUs with door). Possible on-site measures Optical alarm Rx ALC alarm Orange Page 35 Check fibre loss of optical link. Check optical connectors. Clean optical connectors.
(MU: Check optical output power of corresponding OTRx at Master Unit).
(MU: Decrease DL affected band). input power of MF0145A7A_uc_FCC_modif.doc Red Manual for ION-M7P/17P (M-cab)
& Subassemblies Alarms directly related to RU:
Power 28 V Temperature Fan IC Optical alarm Tx Exchange RU. Amplifier Power Down Change power supply (RUs with door). Replace the affected Remote Unit. Reduce environmental temperature. Eliminate thermal short circuit. Disconnect and connect mains. Fans should run. If not, replace the fans at RU. Disconnect and connect mains.
(MU: Change amplifier setting at MU controller). Check power switch inside of RU (RUs with door). Check mains cabling. Check mains power. Status LED off Mains table 5-1 Status LED alarms For the position of the status LED see section 4.2.2 Connections. Explicit troubleshooting is available in the MU software (software manual or WEB Interface). 5.5. EXTERNAL ALARM INPUTS AND OUTPUTS G1038Z0 G1038Z0 figure 5-1 Flange connector, 5 poles figure 5-2 Flange connector, 7 poles Page 36 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies The alarm outputs (open collector output 5 V / 1 mA) are normally low. In case of an alarm they are high active (5 V). They can be used to monitor alarms with an external alarm indicator. The +28 V pin (for its location see figure 5-2 Flange connector, 7 poles) is protected by a 500 mA thermoswitch. In case of exceeding this current between pin 7 and GND and/or in case of a failure of the VSWR module, the thermoswitch turns into a high-
resistive status. In this case no fuse needs to be replaced. Just wait a few minutes until the thermoswitch reaches the normal operating temperature again. Note:
The manufacturer / supplier of this system accepts no liability for damage caused by equipment connected to external outputs or by effects from such equipment. As accessory equipment the alarm kit is available to connect external devices to the external alarm inputs and outputs. For the exact ID No., please refer to section 7.3 Spare Parts. With the external alarm inputs it is possible to monitor the status of connected devices, e.g. a UPS, via software. All alarm inputs are normally high (5 V) without connection. The polarity (high/ low) can be set via the software at the Master Unit (for details please see according software manual). The device to be monitored must be connected so that the alarm contacts will be closed in case of an alarm (I max = 8 mA). The alarm inputs are potential-free with common ground. Subminiature circular connectors series 712 with five and seven contacts, which are contained in the alarm kit, can be ordered directly from the Binder Connector Group, the manufacturer, or indirectly from Andrew Solutions. For the ID No. of the alarm kit see section 7.3 Spare Parts. ION-M alarm outputs
+5 V 4700R ION-M alarm inputs
+5 V 560R Alarm output Alarm GND Alarm input Alarm GND Alarm GND Alarm GND V1651A1 figure 5-3 Alarm inputs and outputs, standard Page 37 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 5.6. TROUBLESHOOTING The status of the Remote Unit can be checked via the Master Unit (for details please refer to the software manual of the Master Controller). Locally, the status can be checked at the LED, see section 5.4 Status LED Alarms. Page 38 MF0145A7A_uc_FCC_modif.doc 6. MAINTENANCE Manual for ION-M7P/17P (M-cab)
& Subassemblies 6.1. GENERAL Read the health and safety warnings in section 1.2. Note:
Note:
The Remote Unit does not require preventative maintenance measures. To prevent malfunctions of the cooling system due to dirt or pollution, it is recommended to clean the heat sink at regular intervals. These cleaning intervals depend mainly on the location of the Remote Unit and the corresponding degree of pollution. the Maintenance of ION-M7P/17P should be performed by replacing only components that are contained in this section. Take care not to unintentionally damage the seals on the modules to maintain warranty. Please keep these guidelines in mind during maintenance:
The spare parts list, consequently, contains only units which can be replaced without tuning or soldering work. Note:
Use an appropriate packaging when sending back the unit (see section 7.2.2 Mechanical Specifications for details). We strongly recommend using the original packaging. Defective parts should only be replaced by original parts from the supplier. All interventions inside the housing are at ones own risk. Ensure the Remote Unit has been disconnected from mains during maintenance. Label any unlabelled cables before disconnecting them to ensure correct re-connection. Note:
Note:
Note:
Maintenance procedures require appropriate tools to ensure correct handling. All these tools can be ordered from the supplier. Note:
All our screws have a right-hand thread and are fastened by turning the tool clockwise and are unscrewed by turning the tool counter-clockwise. Due to the design of the Remote Unit the only component recommended to be replaced is the fan unit. For replacing any other component, please contact the supplier. Page 39 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 6.2. REPLACING THE FAN UNIT Replacement of the fan unit is not required as a preventative measure. Only if an alarm indicates a malfunctioning of a fan must the unit be exchanged. Note:
Please observe that the fan unit can only be replaced as a whole. Do not remove the fans separately. Read the health and safety warnings in section 1.2 as well as the instructions in section 6.1 General before starting with the replacement. 1. Switch off the Remote Unit. Make sure mains is disconnected for the following replacement procedure. Then, proceed as follows:
2. Loosen the four tallow-drop screws is M4x8 by which screwed to the cabinet. Remove the four screws and the corresponding washers. fan plate the 3. Remove the fan unit by putting slight pressure on the fan plate cover to a position that allows access to the fan connector and the earth-bonding cable. 4. Unscrew the fan connector and then disconnect the earth-bonding cable. Fan-unit connector Earth-bonding cable Note:
To observe the specified torque of 650 Ncm for an M5 thread, use an appropriate tool for the following screwing procedures. Page 40 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 5. To mount the new fan unit, re-connect the earth-bonding cable and the fan connector (see step 4). Then, place the fan unit back into its original position and fasten it tight as shown below:
6. Screw the whole fan unit to the cabinet with the four tallow-drop screws M4x8
(see step 2). In order not to exceed the specified torque of 330 Ncm, use an appropriate tool. Page 41 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 6.3. CLEANING THE HEAT SINK Note:
Read the health and safety warnings in section 1.2 Health and Safety Warnings as well as the instructions in section 6.1 General before starting with the replacement procedure. Then, proceed as follows:
1. Switch off the Remote Unit. For the following procedure ensure that mains has been disconnected before!
2. Remove the fan plate with the fan unit from the Remote Unit as described in section 6.2 Replacing the Fan Unit, steps 1 and 2:
3. Use compressed air (max. 5 bar) to blow out the heat sink from back to front:
Compressed air
(5 bar max.) Brush (not metallic) 4. In case the dirt cannot be blown out completely and parts of it stick to the ribs of the heat sink, clean the parts concerned carefully from the front using e.g. a brush. Take care that the material is not scratched or damaged. 5. After cleaning the heat sink, mount the fan unit again according to section 6.2 Replacing the Fan Unit, step 6. Then, switch the Remote Unit back on. Page 42 MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 7. APPENDIX ILLUSTRATIONS 7.1. figure 7-1 Installation drawing MF0145A7A_uc_FCC_modif.doc Page 43 Manual for ION-M7P/17P (M-cab)
& Subassemblies Electrical Optical Link 85 Vac to 264 Vac 115 Vac or 230 Vac max. loaded room temp., idle temp., fully E2000/APC 8 45 dB Single mode E9/125 m 0 dB to 10 dB 550 watts 300 watts 831 x 156 x 147 mm (32.7 x 6.1 x 5.8 in) 20 kg (44 Ib) 7.2. SPECIFICATIONS 7.2.1. Electrical Specifications Power supply Mains power Power consumption Optical link connectors Optical return loss Fibre type Optical link budget 7.2.2. Mechanical Specifications Height, width, depth *
Weight,
* Spacing required 40 mm (1.58 in) around unit All data is subject to change without notice. 7.2.3. Environmental and Safety Specifications Note:
For detailed information, please refer to the Environmental and Safety Specifications leaflet of the supplier, related to ETS 300 019
(European Telecommunication Standard). Operating temperature range Ingress protection RF part Fan part
-33 C to +50 C IP67 IP55 Page 44 All data is subject to change without notice. MF0145A7A_uc_FCC_modif.doc Manual for ION-M7P/17P (M-cab)
& Subassemblies 7.3. SPARE PARTS The following lists contain all parts available for the Remote Unit. The configuration of the delivered unit meets the requirements of the customer and can differ depending on the state of the delivery. Maintenance of the ION-M7P/17P should be performed on an FRU (Field Replaceable Unit) basis only. Do not damage the warranty labels on the components, as this voids the warranty. The following spare parts lists only contain units that can be replaced without tuning or soldering work. To replace an FRU, use the appropriate tools. Replacement tools may be ordered from the supplier. If any FRU not contained in the following list needs to be replaced, please contact customer service for additional instructions. Spare Parts List of the Remote Unit ION-M7P/17P Designation:
ION-M7P/17P Protective Plug E2000 Protective Cap E 2000 Fan Protection Kit Fan Unit Protective Tube Kit Manuals fr ION-M7P/17P & subass (M-cab) Accessories Wall Mounting Pole Mounting Wall-Mounting Kit ISO Trafo Kit 115 V Wall Mounting ISO Trafo Kit 230 V Wall Mounting Connecting Box Kit Wall Mounting Overcoat Housing Kit Wall Mounting Pole-Mounting Kit ISO Trafo Kit 115 V Pole Mounting ISO Trafo Kit 230 V Pole Mounting Connecting Box Kit Pole Mounting Overcoat Housing Kit Pole Mounting Alarm Kit ID No:
7644732 7160013 7158914 7159097 7158254 7162182 7650091-00 FRU x x x x x 7158078 7159340 7158322 7159613 7159625 7157782 7159623 7159621 7159612 7159624 7157396 The manufacturer reserves the right to replace the spare parts listed above by equivalent substitutes. MF0145A7A_uc_FCC_modif.doc Page 45 8. INDEX A Abbreviations Used ................................................ 7 Alarms Alarm Status .................................................... 35 Bite and Alarms ............................................... 35 External Inputs........................................... 36, 37 Handling of Alarms .......................................... 35 List ................................................................... 38 Outputs ...................................................... 36, 37 RU ................................................................... 38 Status LED....................................................... 35 C Cleaning the Heat Sink......................................... 42 Commissioning General............................................................ 32 CommScope Solutions ......................................... 10 Components Accessories ..................................................... 16 Fan-Protection Kit ............................................ 16 Connection Rules Optical Fibers................................................... 27 Optical-Fiber Cables ........................................ 27 Connections Antenna ........................................................... 26 Connector Flange ............................................ 24 Power .............................................................. 25 Contact Addresses Customer Support................................ 11, 12, 13 Customer Support Addresses................... 11, 12, 13 D Declaration of Conformity ..................................... 10 F Flange Connector 5 poles ............................................................. 36 7 poles ............................................................. 36 G Grounding............................................................. 25 Manual for ION-M7P/17P (M-cab)
& Subassemblies H Health and Safety Warnings................................... 8 I Illustrations ........................................................... 43 Installation Electrical .......................................................... 23 Mechanical ...................................................... 17 M Maintenance......................................................... 39 Mounting Fan Protection ................................................. 22 Pole (Outside).................................................. 20 Wall.................................................................. 19 O Optical-Fiber Connection Optical-Fibre Connection Protective-Tube Kit .......................................... 30 Protective Plug ................................................ 28 P Pin Assignment External Alarms ............................................... 37 R Replacement of Fan Unit...................................... 40 S Spare Parts .......................................................... 45 Specifications Electrical .......................................................... 44 Environmental and Safety................................ 44 Mechanical ...................................................... 44 T Troubleshooting.................................................... 38 Page 46 MF0145A7A_uc_FCC_modif.doc
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2012-05-31 | 2110 ~ 2155 | AMP - Amplifier | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2012-05-31
|
||||
| 1 | Applicant's complete, legal business name |
Andrew Wireless System
|
||||
| 1 | FCC Registration Number (FRN) |
0019152750
|
||||
| 1 | Physical Address |
Industriering 10
|
||||
| 1 |
Buchdorf, N/A 86675
|
|||||
| 1 |
Germany
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
D******@phoenix-testlab.de
|
||||
| 1 | TCB Scope |
B1: Commercial mobile radio services equipment in the following 47 CFR Parts 20, 22 (cellular), 24,25 (below 3 GHz) & 27
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
XS5
|
||||
| 1 | Equipment Product Code |
M717P
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
W****** O******
|
||||
| 1 | Title |
Manager Quality
|
||||
| 1 | Telephone Number |
+49-9******** Extension:
|
||||
| 1 | Fax Number |
+49-9********
|
||||
| 1 |
w******@commscope.com
|
|||||
| app s | Technical Contact | |||||
| n/a | ||||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 10/30/2012 | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | AMP - Amplifier | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | ION-M Remote Unit for cellular systems | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Antenna(s) used for this transmitter must be fixed-mounted on indoor or outdoor permanent structures with a maximum gain of 19 dBi. Operating is limited to a maximum antenna hight of 10m above ground per 27.50(d)(2). RF exposure compliance must be addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of 1.1307(b)(3). This device must be professionally installed. Part of booster system connected to Master Unit. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Bureau Veritas Consumer Products Services Germany
|
||||
| 1 | Name |
M****** L******
|
||||
| 1 | Telephone Number |
49-40********
|
||||
| 1 | Fax Number |
49-17********
|
||||
| 1 |
m******@de.bureauveritas.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 27 | 728 | 746 | 20 | Amp | G7D | ||||||||||||||||||||||||||||||||||
| 1 | 2 | 27 | 746 | 757 | 20 | Amp | G7D | ||||||||||||||||||||||||||||||||||
| 1 | 3 | 27 | 2110 | 2155 | 20 | Amp | F9W | ||||||||||||||||||||||||||||||||||
| 1 | 4 | 27 | 2110 | 2155 | 20 | Amp | G7D | ||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC