QUICK START GUIDE eufy Security C220 Smart Lock Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. Model: T8506 V01 AT A GLANCE Fingerprint Button Battery Indicator Keypad Status Light and Lock / Unlock Button Blue: Door unlocked Orange: Door locked Red: Abnormal state Keyway: Can be copied, can't be rekeyed. USB-C Port: Charges the lock in emergency situations. 01 EN Set Battery Compartment Setup Button Thumbturn Screw Hole EN 02 WHAT'S INCLUDED For Smart Lock Installation
(Step 2) Deadbolt Installation Set A B INSTALLATION Step 1. Prepare the Door 1. Remove the existing lock and check your door. 2. Check if your door has holes like the one below. Standard US doors are already compatible. If not, follow the template to drill holes on your door. Deadbolt Deadbolt Screws / Strike Screws
(Step 3) Exterior Assembly C Exterior Assembly
(Step 4) Interior Assembly Installation Set D E F G H Interior Assembly Screws Silicone Plug Interior Assembly Screws Batteries
(Step 5) Strike Plate Installation Set I J K Strike Platey Strike Screws Keys Backset 2" / 60 mm or 2" / 70 mm Minimum Distance 1/" / 45 mm Door Hole Diameter 1" / 25 mm Cross Bore Diameter 1 " / 38 mm 2 " / 54 mm Door Thickness 1" - 2/"
35 mm - 55 mm 03 EN EN 04 Step 2. Install Deadbolt 1. Check your door to see if the deadbolt requires adjustment.
*Check the latch hole before inserting the deadbolt. If the latch hole is round, refer to diagram A. If the latch hole is rectangular, refer to diagram B. Backset Latch Hole 2-3/8 1 8 0 2-3/4 2" / 60 mm If the backset is 60mm, insert the deadbolt directly. If the backset is 70mm, rotate the faceplate of the deadbolt 180 to extend the length. Diagram A If the latch hole is round, contact customer service to receive a round drive-
in faceplate, then replace the existing one. 2" / 70 mm Diagram B 2. Insert and screw the deadbolt into the doorframe. A B Deadbolt Deadbolt Screws / Strike Screws 05 EN Make sure the word "TOP"
on the deadbolt faces up. EN 06 Step 3. Install Exterior Assembly Step 4. Install Interior Assembly Remove the spacer before installation if you have a 38 mm cross bore. 1. Detach the back cover from the interior assembly. Cross Bore Diameter 1 " / 38 mm 2. Run the wires through the back cover. 07 EN EN 08 3. Secure the back cover with screws. 5. Mount the interior assembly. Make sure both wires are tucked into the cabin on the back of the interior assembly. Tightly fasten the screws in place. Set the screws with your hands, then use a screwdriver to secure them. E Screws Set 4. Wire to the interior assembly. Set Make sure the deadbolt is retracted and the thumb turn knob is on the 'unlock'
position, check if the deadbolt moves properly by turning the thumbturn. 09 EN EN 10 Set Set 6.Install the 8 AA batteries provided with the correct polarity. Don't put on the cover until the system setup is done in the app.
*For your convenience, please first install the bottom layer of 4 AA batteries. Set H Batteries Friendly Reminder: When removing the batteries, first remove the upper layer, then gently pull the ribbon to lift the remaining batteries out of the compartment. F G Silicone Plug Interior Assembly Screws Set Set
*Use a long screwdriver to fasten the Interior Assembly screws. 11 EN EN 12 Step 5. Install Strike Plate Latch Hole Depth 25.4mm/1''
SETTING UP THE SYSTEM 1. Download and install the eufy Security app, then sign up for an account. I J Strike Platey Strike Screws Make sure the depth of the latch hole on door frame is deep enough (1" / 25.4 mm), otherwise the calibration might fail during the setup. 2.Follow the in-app instructions to add the Smart Lock C220 to your device list. Please visit https://support.eufylife.com/s/ or scan the QR code for more information. 13 EN EN 14 NOTICE Warning replacement of a battery with an incorrect type that can defeat a safeguard;
disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Notice (United States Of America) FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/
TV technician for help. 15 EN FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. The following importer is the responsible party Company Name: POWER MOBILE LIFE, LLC Address: 10900 NE 8th St, Ste 501, Bellevue WA 98004 Telephone:1-800-988-7973 Notice (Australia) Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for the device and accessories is -20C to 50C. It is recommended to supply the device in an environment with a temperature that ranges from 5C~25C. When supplying, please place the device in an environment that has a normal room temperature and good ventilation. Warning:
replacement of a battery with an incorrect type that can defeat a safeguard;
disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product. EN 16 Notice (Canada) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1)this device may not cause interference, and
(2)this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1)l'appareil nedoit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. IC RF Statement:
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matire d'exposition RF. Attention:
remplacement dune batterie par un type incorrect pouvant supprimer une protection mise au rebut dune batterie dans un feu ou dans un four chaud, ou crasement mcanique ou coupure dune batterie, susceptible de provoquer une explosion;
maintien dune batterie dans un environnement trs haute temprature pouvant provoquer une explosion ou la fuite de liquide ou de gaz inflammables;
et batterie soumise une pression de lair extrmement faible pouvant provoquer une explosion ou la fuite de liquide ou de gaz inflammables. ATTENTION RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACE PAR UN TYPE INCORRECT. LIMINER LES BATTERIES USES SELON LES INSTRUCTIONS 17 EN Customer Service 12-month limited warranty
(US) +1 (800) 988-7973
(UK) +44 (0) 1604 936200
(DE) +49 (0) 69 9579 7960
) +86 400 0550 036
) +81 03 4455 7823
(AU) +61 3 8331 4800
(Egypt) +20 8000000826
(UAE) +971 8000320817
(Kuwait) +965 22069086
(Saudi Arabia) +966 8008500030
(Middle East & Africa) +971 520750842 support@eufy.com Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
@EufyOfficial
@EufyOfficial
@EufyOfficial