FCC ID: 2AOKB-T8502 eufy Security Smart Lock E110

QUICK START GUIDE Smart Lock E110 Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. Model: T8502 51005003084 V01 AT A GLANCE Keypad Status Light Blue: Door unlocked Orange: Door locked Red: Abnormal Keyway USB-C Port: Charges the lock in emergency situations. 01 Battery Compartment Serial Number:Use to add the lock to the eufy Security app. QR Code:Use to add the lock to the eufy Security app. SYNC Button:Use to pair the lock with the doorbell chime. Thumbturn Screw Hole 02 INSTALLATION What You Need Step 2. Deadbolt Installation Set Step 1. Prepare the Door 1. Remove the existing lock and check your door. 2. Check if your door has holes like the one below. Standard US doors are already compatible. Backset 2" / 60 mm or 2" / 70 mm A B Step 3. Exterior Assembly E Step 4. Interior Assembly Installation Set Minimum Distance 2" / 60 mm Door Hole Diameter 1" / 25 mm F G H I J K Step 5. Strike Plate Installation Set Cross Bore Diameter 1 " / 38 mm 2 " / 54 mm Door Thickness 1" - 1 "

35 mm - 44.5 mm C D 03 If not, follow the template to drill holes on your door. 04 Step 2. Install Deadbolt 1. Check your door to see if the deadbolt requires adjustment. 2. Insert and screw the deadbolt into the doorframe. Backset Latch Hole 2-3/8 1 8 0 2-3/4 2" / 60 mm If the backset is 70 mm, turn the faceplate 180 to extend the length. 2" / 70 mm A B Make sure the word "TOP" on the deadbolt faces up. 05 06 Step 3. Install Exterior Assembly Step 4. Install Interior Assembly Remove the spacer before installation if you have a 38 mm cross bore. 1. Detach the back cover from the interior assembly. Cross Bore Diameter 1 " / 38 mm 2. Run the wires through the back cover. 07 08 3. Secure the back cover with screws. 4. Wire to the interior assembly. Tightly fasten the screws in place. Set the screws with your hands, then use a screwdriver to secure them. G

(Optional) If the back cover is not fastened tightly to the door, use the additional screw provided. 5. Mount the interior assembly. Make sure both wires are tucked into the cabin on the back of the interior assembly. J 09 10 6. Install the 4 AA batteries provided with the correct polarity. Don't put on the cover until the system setup is done in the app. Check if the deadbolt retracts properly by turning the thumbturn. K 11 12 H I Step 5. Install Strike Plate SETTING THE SYSTEM 1. Download and install the eufy Security app, then sign up for an account. C D Please visit https://support.eufylife.com/s/ or scan the QR code for more information. 2. Follow the in-app instructions to add the Smart Lock E110 to your device list. 13 14 NOTICE Warning replacement of a battery with an incorrect type that can defeat a safeguard;

disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;

leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Notice (United States Of America) FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/

TV technician for help. 15 FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. The following importer is the responsible party Company Name: POWER MOBILE LIFE, LLC Address: 10900 NE 8th St, Ste 501, Bellevue WA 98004 Telephone:1-800-988-7973 Notice (Australia) Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. It is recommended to supply the device in an environment with a temperature that ranges from 5C~25C. When supplying, please place the device in an environment that has a normal room temperature and good ventilation. Warning:

replacement of a battery with an incorrect type that can defeat a safeguard;

disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;

leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product. 16 Notice (Canada) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)this device may not cause interference, and

(2)this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1)l'appareil nedoit pas produire de brouillage, et

(2)l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. IC RF Statement:

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matire d'exposition RF. Attention:

remplacement dune batterie par un type incorrect pouvant supprimer une protection mise au rebut dune batterie dans un feu ou dans un four chaud, ou crasement mcanique ou coupure dune batterie, susceptible de provoquer une explosion;

maintien dune batterie dans un environnement trs haute temprature pouvant provoquer une explosion ou la fuite de liquide ou de gaz inflammables;

et batterie soumise une pression de lair extrmement faible pouvant provoquer une explosion ou la fuite de liquide ou de gaz inflammables. Customer Service 12-month limited warranty

(US) +1 (800) 988-7973

(UK) +44 (0) 1604 936200

(DE) +49 (0) 69 9579 7960

) +86 400 0550 036

) +81 03 4455 7823

(AU) +61 3 8331 4800

(Egypt) +20 8000000826

(UAE) +971 8000320817

(Kuwait) +965 22069086

(Saudi Arabia) +966 8008500030

(Middle East & Africa) +971 42428633 support@eufylife.com Anker Innovations Limited ATTENTION RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACE PAR UN TYPE INCORRECT. LIMINER LES BATTERIES USES SELON LES INSTRUCTIONS Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

@EufyOfficial

@EufyOfficial

@EufyOfficial 17

SECURITY 5) oufy O eufy Security Smart Lock E110 Model: T8502 Room 1318-19,Hollywood Plaza,610 Nathan Road,Mongkok, Kowloon,Hong Kong Anker Innovations Limited Made in China IPX3 for exterior assembly IC: 23451-T8502 FCC ID: 2AOKB-T8502 CAN ICES-003(B)/NMB-003(B)

Anker Innovations Limited Agent Authorization Letter

(10/12/2022) RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern:

We, authorize Micom Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. This agreement expires one year from the current date. Sincerely, Louis Qi/Manager Company Name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2AOKB-T8502 Anker Innovations Limited Date: 2022-10-13 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description SW SECURITY DESCRIPTION Parts List Tune up In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: louis Qi Title: Manager