FCC ID: 2AOKB-T81A0 S120 Solar Wall Light Cam

QUICK START GUIDE S120 Solar Wall Light Cam AT A GLANCE WHATS INCLUDED CHARGING THE CAMERA SETTING UP Ensure Tight Seal SYNC UP Ensure Tight Seal SYNC S120 Solar Wall Light Cam Model: T81A0 Mounting Bracket Mounting Screws 1. Download and install the eufy Security app, and sign up for an account. Charging cable and AC adapter are not included. 2. Follow the on-screen instructions to add your Solar Wall Light Cam. Solar Panel Camera LED Indicator Microphone USB-C Charging Port SYNC Button Speaker Camera Fixing Screw USB-C Extension Cable Quick Start Guide MOUNTING Select a Location The camera can be mounted on a wall or similar surface. Select a location where the solar panel will not be blocked by obstacles such as a roof or leaves. Location Height We recommend mounting 2 m - 2.5 m (6.6 ft - 8.2 ft) above ground level. To maximize solar panel efficiency and the camera field of view, select a location where the camera receives plenty of sunlight. Mount the Camera 1. Mark the mounting points on the wall or surface where drilling will be required, using the mounting bracket as a template. UP If it isn't possible to completely avoid the solar panel being blocked by obstacles, try to allow as much exposure to sunlight as possible. Pay attention to battery management via the app to make sure your device receives enough power to continue operating. If your Solar Wall Light Cam does not receive enough power to continue operating, it can be charged manually, or an additional solar panel (with USB-C extension cable) can be connected and placed in a location with sufficient sunlight to stay powered. Camera Field of View Motion Detection Zone

. t f 2 8

6 6

. m 5 2

2

2. Drill holes in the wall or surface, then insert the expansion anchors into the holes. This step applies if mounting onto hard surfaces such as brick or concrete. For soft surfaces such as wood, skip this step. 01 02 03 04 05 06 07 08 3. Screw the mounting bracket onto the wall. UP 4. Slot the camera onto the mounting bracket and make sure it is attached securely. UP UP 5. Insert and tighten the camera fixing screw at the bottom of the camera. UP SAFETY Do not use the product in an environment where the temperature is too high or too low. Never expose the product to wet environments. The suitable temperature for devices and accessories is -20C to 50C

(Charging temperature is 0C to 40C). It is recommended to supply the device in an environment with a temperature that ranges from 5C to 25C. Unless specifically indicated that it is safe to do so in the user guide or instruction manual, do not use this device in an environment that exceeds the recommended low or high temperature. Unless specifically indicated that it is safe to do so in the user guide or instruction manual, avoid exposing your device to direct sunshine or excessively wet environments. When supplying power, place the device in an environment that has a normal room temperature and good ventilation. The light source contained in this luminaire should only be replaced by the manufacturer, its service agent or a similarly qualified person. SCURIT Nutilisez pas le produit dans un environnement o la temprature est trop leve ou trop basse. N'exposez jamais lappareil un ou un environnement humide. La temprature approprie pour le produit et les accessoires est comprise entre -20 C et 50C(la temprature de charge est de 0 C 40 C). Il est recommand dalimenter lappareil dans un environnement dont la temprature est comprise entre 5 C et 25 C. moins quil ne soit spcifiquement indiqu dans le guide de lutilisateur ou le manuel dinstructions que cela est sans danger, nutilisez pas cet appareil dans un environnement qui dpasse les tempratures basses ou leves recommandes. Sauf indication contraire dans le guide de lutilisateur ou le manuel dinstructions, vitez dexposer votre appareil aux rayons directs du soleil ou des environnements excessivement humides. 09 10 Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. 51005003795 V01 Lors de lalimentation lectrique, placez lappareil dans un environnement ayant une temprature ambiante normale et une bonne ventilation. La source lumineuse contenue dans ce luminaire ne doit tre remplace que par le fabricant, son agent de service ou une personne galement qualifie. NOTICE FCC Statement CAUTION!

THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED. DISPOSE OF USED BATTERIES ACCORDING TO THEIR INSTRUCTIONS. ATTENTION!

IL EXISTE UN RISQUE DEXPLOSION EN CAS DUTILISATION DUN TYPE DE PILE INCORRECT. LIMINEZ LES PILES USAGES CONFORMMENT AUX INSTRUCTIONS. Warning:

Replacing a battery with an incorrect type may bypass safeguards and create danger;

Disposal of a battery in a fire or other source of significant heat, or by crushing, or cutting, may result in an explosion as well as leakage of flammable liquids and gases;

Leaving a battery in an extremely hot environment may result in an explosion as well as leakage of flammable liquids and gases;

A battery subjected to extremely low air pressure may result in an explosion as well as leakage of flammable liquids and gases. Attention:

-Le remplacement dune batterie par un type incorrect peut contourner les protections et crer un danger ;

-Llimination dune pile dans un feu ou une autre source de chaleur importante, ou par crasement ou dcoupage, peut entraner une explosion ainsi quune fuite de liquides et de gaz inflammables ;

-Le fait de laisser une batterie dans un environnement extrmement chaud peut entraner une explosion ainsi quune fuite de liquides et de gaz inflammables ;

-Une batterie soumise une pression dair extrmement faible peut provoquer une explosion ainsi quune fuite de liquides et de gaz inflammables. 11 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible or compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna.

(2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help. FCC Radio Frequency Exposure Statement T h e d e v i c e h a s b e e n e v a l u a t e d t o m e e t g e n e r a l R F e x p o s u r e requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. The following importer is the responsible party:

Company Name: POWER MOBILE LIFE, LLC Address: 10900 NE 8th St, Ste 501, Bellevue WA 98004 Telephone:1-800-988-7973 IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device."

Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement."

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. IC RF Statement When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matire d'exposition RF. Declaration of Conformity This product complies with the radio interference requirements of the European Community. Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site: https://uk.eufylife.com/. This product complies with the radio interference requirements of the United Kingdom. Hereby, Anker Innovations Limited declares that this product is in compliance with Radio Equipment Regulations 2017(SI2017/1206). The full text of the UK declaration of conformity is available at the following internet address: https://uk.eufylife.com RF exposure information:

The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use product that maintains a 20cm distance between the device and the human body. Frequency bands and power as below:

Function Bands Operation Frequency Max. Power Wi-Fi 2.4GHz 2412-2472MHz EIRP 19.94 dBm The following importer is the responsible party (contract for EU matters):

Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807 Munich, Germany The following importer is the responsible party (contract for UK matters):

Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford,Hertfordshire, WD17 1HP, United Kingdom This product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product. CUSTOMER SERVICE 12-month limited warranty

(US) +1 (800) 988-7973

(UK) +44 (0) 1604 936200

(DE) +49 (0) 69 9579 7960

) +86 400 0550 036

) +81 03 4455 7823

(AU) +61 3 8331 4800

(Egypt) +20 8000000826

(UAE) +971 8000320817

(Kuwait) +965 22069086

(Saudi Arabia) +966 8008500030

(Middle East & Africa) +971 520750842 support@eufy.com Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

@EufyOfficial

@EufyOfficial

@EufyOfficial 12 13 14 15

Attestation Letter Date: 2023-05-23 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(5)(i)(ii) Filing FCC ID:2AOKB-T81A0 Anker Innovations Limited (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Anker Innovations Limited (the applicant) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Signature Contact Person: Louis Qi Title: Manager Company Name& Address: Anker Innovations Limited & Room 1318-19, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong CFR 47 2.911(d)(5)(i)(ii) Attestation Letter

AnkerInnovationsLimited Add: Room 131819, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong Tel:+8675586544807 Email:Louis.qi@anker.com Date:20230523 AttestationLetter FEDERALCOMMUNICATIONSCOMMISSION AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 DearSirorMadam:

We,Anker Innovations Limited, declared that the device does not support channel1213 in 2.4GHz wifi band and any nonUS channels in all the operational mode(s) for the following product. Product:S120SolarWallLightCam Model:T81A0 FCCID:2AOKBT81A0 Pleasecontactmeifthereisneedforanyadditionalclarificationorinformation. BestRegards, SincerelyYours, Signature:

PrintedName:LouisQi Title:Manager

Anker Innovations Limited Add: Room 1318-19, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong Tel: +86-755-86544807 Email: Louis.qi@anker.com FCC Authorization Date: 2023-05-23 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We , Anker Innovations Limited, Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd

(Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Clients signature Printed Name: Louis Qi Title: Manager QA-FR-170-B

Anker Innovations Limited Add: Room 1318-19, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong Tel: +86-755-86544807 Email: Louis.qi@anker.com FCC Confidential Authorization Date: 2023-05-23 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID:2AOKB-T81A0 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, (Anker Innovations Limited) hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature:

Printed Name: Louis Qi Title: Manager QA-FR-171-A

U.S. AGENT LETTER OF ATTESTATION Date: 2023-05-23 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(7) Filing FCC ID:2AOKB-T81A0 Anker Innovations Limited (the Applicant) certifies that, as of the date of the filing of the application, Fantasia Trading LLC is our designated U.S. agent for service of process for the above referenced FCC ID. Anker Innovations Limited (the Applicant) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Fantasia Trading LLC accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Company Name: Fantasia Trading LLC Address: 5350 Ontario Mills Pkwy, STE 100, Ontario, CA 91764 FRN: 0033423005 Tel.: +1 (800)988 7973 Email: louis.qi@anker-in.com Signed by (printed name): Louis Qi Signature:

Applicant: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza 610 Nathan Road, Mongkok Kowloon Hong Kong FRN: 0027073105 Tel: +86-755-86544807 Email: Louis.qi@anker.com Signed by (printed name): Louis Qi Signature: