FCC ID: 2AOKB-T8124R SoloCamn S230

QUICK START GUIDE SoloCam S230 Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. 51005002837 V02 TABLE OF CONTENTS PRODUCT OVERVIEW 02 CHARGING SOLOCAM 03 SETTING UP SOLOCAM 04 05 MOUNTING SOLOCAM 08 NOTICE EN 01 CHARGING SOLOCAM Battery-powered Charging Fully charged Solid blue Off PRODUCT OVERVIEW 1 5 4 3 7 Model:T8124R 10 6 2 8 9 1. Solar Panel 2. Camera Lens 3. Motion Sensor 4. Photosensitive Sensor 5. Microphone 6. LED Indicator 7. SYNC Button 8. Type-C Charging Port 9. Mounting Hole 10. Speaker 02 EN EN 03 SETTING UP SOLOCAM MOUNTING SOLOCAM Download the App and Set up the System Select a Location 1. Download and install the eufy Security app, and sign up for an account. SoloCam S230 can be mounted on a wall. Select a location where you can get the desired view. We recommend hanging it 7-10 ft (2-3 m) above the ground. To maximize the solar panel efficiency, select a location where SoloCam S230 can receive more sunlight. 2. Follow on-screen instructions to add your SoloCam . 04 EN EN 05 Camera field Camera field of view of view Motion Motion Detection Detection Zone Zone Up to 26 ft (8 m) t f 0 1

7

) m 3

2

Mount SoloCam S230 SoloCam S230 can be mounted both outdoors and indoors. 1. Turn the knob of the mounting bracket counterclockwise to loosen and disassemble it. 3. Firmly screw the knob of the mounting bracket into the mounting hole of SoloCam. 2.Drill holes with a 15/64 inch (6 mm) drill bit, then insert the anchors into the holes; anchors are necessary for walls that are made out of hard materials such as concrete, brick, or stucco. 4. Hold and screw SoloCam to the mounting bracket. Rotate SoloCam to adjust the view and check it using the live stream which you can access in the eufy Security app. SoloCam S40 can be also installed on the ceiling. Follow the steps 1-4 mentioned above to install it. Tips:

For troubleshooting, check Help on the eufy Security app. Refer to the app page for LED indicator status. 06 EN EN 07 NOTICE FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/

TV technician for help. FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20 cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. The following importer is the responsible party. Company Name: POWER MOBILE LIFE, LLC Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004 Telephone: 1-800-988-7973 08 EN IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. IC RF Statement When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matire d'exposition RF The recommended temperature range for devices and accessories is -20C to 60C (Charging temperature is 0C to 40C) . Warning:

Replacing a battery with an incorrect type may bypass safeguards and create danger;

Disposal of a battery in a fire or other source of significant heat, or by crushing, or cutting, may result in an explosion as well as leakage of flammable liquids and gases;

Leaving a battery in an extremely hot environment may result in an explosion as well as leakage of flammable liquids and gases;

A battery subjected to extremely low air pressure may result in an explosion as well as leakage of flammable liquids and gases. Attention:

-Le remplacement dune batterie par un type incorrect peut contourner les protections et crer un danger ;

-Llimination dune pile dans un feu ou une autre source de chaleur importante, ou par crasement ou dcoupage, peut entraner une explosion ainsi quune fuite de liquides et de gaz inflammables ;

-Le fait de laisser une batterie dans un environnement extrmement chaud peut entraner une explosion ainsi quune fuite de liquides et de gaz inflammables ;

-Une batterie soumise une pression dair extrmement faible peut provoquer une explosion ainsi quune fuite de liquides et de gaz inflammables. Customer Service Warranty 12-month limited warranty Call Us United States

+1 (800) 988 7973 United Kingdom

+44 (0) 1604 936 200 Germany

+49 (0) 69 9579 7960 Mon-Fri 6:15-17:00(PT) Sat-Sun 6:30-16:30(PT) Mon-Fri 6:00-17:00 Sat-Sun 6:00-14:00 Mo-Fr 8:00-16:00 Email Us Customer Support: support@eufylife.com Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

@EufyOfficial

@EufyOfficial

@EufyOfficial

Anker Innovations Limited Section 2.911(d)(5)(i) Certification Equipment Type Company name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Product Name: SoloCamn S230 FCC ID: 2AOKB-T8124R Model(s): T8124R 2.911(d)(5)(i) Equipment Type We, [Anker Innovations Limited] (the applicant) certify that the equipment for which authorization is sought through certification is not:

Prohibited from receiving an equipment authorization pursuant to 2.903; of the FCC rules. Identified as an equipment type in the Covered List NOTE 1 Yours sincerely, Name: louis Qi Date: 2023-12-01 Title and Company name: Manager/ Anker Innovations Limited NOTE 1 Covered List; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References;

1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the 2.911 (d)(5)(i) Equipment Type Attestation v1.2

Anker Innovations Limited Section 2.911(d)(5)(ii) Certification Applicant (Covered List) Company name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Product Name: SoloCamn S230 FCC ID: 2AOKB-T8124R Model(s): T8124R 2.911(d)(5)(ii) Applicant filing We, [Anker Innovations Limited] (the applicant) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the Covered List NOTE 2, established pursuant to 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: louis Qi Date: 2023-12-01 Title and Company name: Manager/ Anker Innovations Limited NOTE 1 Delete option not applicable to this application. NOTE 2 Covered List; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References;

1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the 2.911 (d)(5)(ii) Applicant Attestation v1.2

Anker Innovations Limited Section 2.911(d)(7) USA Agent for Service of Process Company name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Product Name: SoloCamn S230 FCC ID: 2AOKB-T8124R Model(s): T8124R 2.911(d)(7) USA Designated Agent for Service of Process We, [Anker Innovations Limited] (the applicant) designate [Fantasia Trading LLC]

NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: Fantasia Trading LLC Address: 5350 Ontario Mills Pkwy, STE 100, Ontario, CA 91764 FRN of U.S. agent: 0033423005 Contact Name: Louis Qi Telephone No: +1 (800)988 7973 Email: louis.qi@anker-in.com Applicant Company name: Anker Innovations Limited Address: Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong FRN:0027073105 Contact Name: Louis Qi Telephone No: +86 13652441319 Email:

louis.qi@anker-in.com

Signature Signature:

2.911 (d)(7)USA Agent v1.2 Fantasia Trading LLC Title: Compliance Manager Date: 2023-07-13 Title: Compliance Manager Date: 2023-07-13 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the 2.911 (d)(7)USA Agent v1.2

Anker Innovations Limited Agent Authorization Company: Anker Innovations Limited Address:Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Product Name:SoloCamn S230 Model Number(s):T8124R Product Description:SoloCamn S230 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Louis Qi Title:

Manager Company: Anker Innovations Limited Date: 2023-12-1

Anker Innovations Limited Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2AOKB-T8124R Date: 2023-12-01 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description SW SECURITY DESCRIPTION Parts List Tune up In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: louis Qi Title: Manager