FCC ID: 2AOKB-T8321M Video Baby Monitor 720P ( 2.4G FHSS Transmitter )

Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners. 51005002167 V01 USER MANUAL Video Baby Monitor 720P TABLE OF CONTENTS Whats in the Box 02 09 Mounting the Baby Camera on the Wall Feature Introduction 03 12 Monitor Menu Settings Setting Up the Camera and Monitor 05 15 Notice Adding a New Baby Camera to the Baby Monitor 07 19 Customer Service Using the Baby Monitor 08 English 01 WHATS IN THE BOX FEATURE INTRODUCTION Video Baby Monitor 720P Video Baby Monitor 720P Model: T8321-C Model: T8321-M FCC ID:2AOKB-T8321C FCC ID:2AOKB-T8321M IC:23451-T8321C IC:23451-T8321M Wall Mount Monitor Micro-USB Power Cable (1 m) Camera Micro-

USB Power Cable

(3 m) Camera Adapter

(5V 1A) Monitor Features 1 2 10 11 12 3 4 5 9 8 7 6 13 6 LED indicator Red: charging White: Fully charged 7 Micro USB charging port 1 Screen 2 Menu button 3 Navigation button 4 OK button Press to confirm the 8 Volume down selection Press to switch camera display if more than 2 cameras added 5 Return to previous level of menu Press and hold to speak to the camera When menu is opened, press to return to the previous level of menu 9 Volume up 10 Zoom button 11 Power button 12 Reset 13 Speaker Monitor Adapter (5V 2A) Mounting Screws User Manual

/ Talk button Welcome Card Welcome Card Note: Power adapter varies by region. 02 English English 03 Camera Features 1 2 SETTING UP THE CAMERA AND MONITOR Charge the Monitor Fully charge the monitor before use. To charge:

other end to the power adapter (5V/2A). 2. Plug the adapter into a power outlet. 1. Connect one end of the micro USB cable to the baby monitor, and the 7 5 4 3 6 3. Press and hold the power button for 2 seconds to turn the baby monitor on. 1 Microphone 5 Pairing button 2 3 Standard camera lens 6 Micro USB port LED indicator 7 Speaker 4 Temperature & humidity sensor 5V/2A 04 English English 05 Charge the Camera 1. Connect one end of the micro USB cable to the baby camera, and the other end to the power adapter (5V 1A). 2. Plug the power adapter into a power outlet. ADDING A NEW BABY CAMERA TO THE BABY MONITOR The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the following steps when adding extra baby cameras or after resetting a baby camera. 1. Enter menu settings, go to Camera -> Add Camera, then follow the onscreen instructions to start the pairing. 4 06 12 AM

5V/1A The new baby monitor and camera will set up automatically. You are all set to use the products after the monitor and camera are fully charged. 2. Press and hold the pairing button on the rear of the camera for 1 second until a notification prompt is heard. 3. Check the firmware version of the monitor (see image below) to make sure your baby monitor and camera are running the same, latest firmware version. 4 06 12 AM

Add Camera Delete Camera Cycle Cameras Camera Settings 60 Secs Scanning for new camera 1Secs Push the button on the camera to pair. Night Vision Mode Time Set Sleep Mode Anti-Screen Flicker Language Default Settings Temperature Unit Connect with Us https://www.eufylife.com United States +1 (800) 988 7973 United Kingdom +44 (0) 1604 936 200 Germany +49 (0) 69 9579 7960 Japan +81 03 4455 7823 support@eufylife.com Monitor: v x.x.x Camera: v x.x.x SN: T8300E0A18370E72 06 English English 07 To check whether it is the latest version:

1 Visit the website below:

https://www.eufylife.com/support/5505/spaceview-baby-monitor 2 If the firmware version is lower than the version shown online

(highlighted in green), click the firmware version to download. The downloaded file includes firmware for both T8300 and T8321 models, make sure you use the T8321 firmware. 3 Follow the steps in the eufy Security Software Upgrade Guide video or Firmware Upgrade Manual to complete firmware upgrade. Note: The eufy Security Spaceview baby camera can be added to the monitor. Before adding the camera, make sure SpaceView baby camera is running the same, latest version (in the T8300 folder) with the monitors. USING THE BABY MONITOR When more than 2 cameras are added to the monitor, you can manually switch among cameras by pressing the monitors OK button. Once the camera switch is completed, the icon of the selected camera will appear on the corner of the baby monitor . You can also select the Cycle Camera option. The screen cycles through the list of connected baby cameras according to the preset intervals. Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is resolved once the camera is moved away from the monitor. MOUNTING THE BABY CAMERA ON THE WALL 1. Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw holes with a pencil. UP 2. Drill 5 1

'' holes into the wall and then insert anchors into the holes. Anchors are not needed for wooden walls. 08 English English 09 3. Insert the screws through the mounting holes of the wall mount and screw into the anchors. 5. To get the optimal viewing angle, rotate the camera (25upwards, 60 backwards, 250 horizontally) manually, as pan and tilt functions are not supported on this model when using the navigation button. 72 F 60 25 250 4. Snap the baby camera onto the wall mount. UP UP 10 English English 11 MONITOR MENU SETTINGS Press and hold the power button to power on the monitor. Press the menu button to open Menu Settings. Menu Options Description Time Set Set the time on the monitor. Menu Settings Night Vision Mode When Auto is enabled, the camera will change the screen color according to the light conditions in the room. When disabled, the camera will stick to daylight screen color and will not change when the surrounding environment is getting dark. Note: We recommend setting this function to On for most of the situations. Anti-Screen Flicker Changes the refresh rate of the screen to prevent flickering. Language Sets the on-screen display menu language. Default Settings Resets all options to their default setting. Temperature Unit Select your desired temperature measure unit. Connect with Us Contact details Note: The interval duration between each sound alert is 30 seconds. It will not sound alerts during this interval, even if the conditions are met to trigger an alert. 4 06 12 AM

Brightness Menu Options Description Brightness Set the brightness of the screen. Sleep Mode Sound Alert Lullaby Alarm Zoom Zoom in / out Enable to automatically turn off the screen after 1 min, 3 min, 5 min or Off. You can set the baby monitor to alert you when a specific noise level is detected. Note: Surrounding noise might set off false alarm. Select your desired lullaby song. You can adjust the volume by selecting the volume button. Note: Sound Alert is automatically disabled when Lullaby function is enabled. Warning: Your babys cry might be obscured by the sound of a lullaby. Set alarm on/off Specify the duration when the alarm will sound. Set the volume Set the temperature alert when it exceeds the specified temperature Set an alarm clock Add Camera Note: You can add up to 4 cameras per baby monitor. Cycle Cameras Cycles through the list of connected baby cameras according to the preset intervals. Camera Delete Camera 12 English English 13 On-screen Menu Icons Icon Icon Description Wireless signal strength Night Vision Mode is enabled 1 Shows the camera that is currently presenting on the baby monitor screen Note: This icon will not appear on the screen when there is only one camera connected to the monitor. Cycle Cameras enabled Sound Alert enabled Sound level of the room the camera is in 08:30 AM Current time Current battery level of the baby monitor 72 F Current operating temperature NOTICE Warning Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided. This product complies with the radio interference requirements of the European Community. Declaration of Conformity Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site:

www.eufylife.com This product can be used across EU member states. Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The connection to so called power USB is prohibited. The adapter shall be installed near the equipment and shall be easily accessible. Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for T8321-M and accessories is -20C-40C The suitable temperature for T8321-C and accessories is -20C-40C When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature that ranges from 5C~25C. Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may cause danger and violate the authorization of the device and the guarantee article. 14 English English 15 The charger output voltage/current is 5Vdc/1A(for T8321-C) and 5Vdc/2A

(for T8321-M).The plug considered as disconnect device of adapter. If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc / 1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body. Operating Frequency Range: 2410-2477MHz The T8321-C Max Output Power: 18.04dBm(EIRP), The T8321-M Max Output Power: 14.89dBm (EIRP) CE SAR:

This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm from the body. The SAR limit of Europe is 4.0 W/

kg. Device types T8321-M has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the limb is1.707W/kg . This device was tested for typical hand held operations with the back of the device kept 0mm from the Limb. The T8300-C device has been evaluated to meet general RF exposure requirements and can be used in fixed exposure condition. RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body. The following importer is the responsible party (contact for EU matters only) Importer: Anker Technology (UK) Ltd Importer Address:Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, United Kingdom B11 2AA This product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

(1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help. FCC Radio Frequency Exposure Statement The T8321-C device has been evaluated to meet general RF exposure requirements. The T8321-C can be used in fixed exposure condition. The min 16 English English 17 separation distance is 20cm. This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm from the body. RF Exposure Information (SAR) The Extremity SAR limit of FCC for Hand held is 4.0W/kg. Device is recommended to use in hand held only and SAR when hand held is 1.804 W/kg Worn on body will have unexpected RF exposure RISK. FCC ID (for T8321-C): 2AOKB-T8321C FCC ID (for T8321-M): 2AOKB-T8321M The following importer is the responsible party. Company Name: POWER MOBILE LIFE, LLC Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541 Telephone:1-800-988-7973 CUSTOMER SERVICE Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong Warranty 12-month limited warranty Call Us United States +1 (800) 988 7973 Mon-Fri 9AM-5PM (PT) United Kingdom +44 (0) 1604 936 200 Mon-Fri 6AM-11AM (GMT) Germany +49 (0) 69 9579 7960 Mon-Fri 6:00-11:00 Email Us Customer Support: support@eufylife.com

@EufyOfficial

@EufyOfficial eufyofficial 18 English English 19

Anker Innovations Limited Date: 2020/4/20 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: Request of Confidentiality for FCC ID: 2AOKB-T8321M To Whom it may concern:

Pursuant to sections 0.457 and 0.459 of Commissions Rules(CFR 47), and Section 552(b)(4) of the Freedom of Information Act, Anker Innovations Limited hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality (max time 180 days from grant date) as outlined in Public Notice DA04-1705. This provision will give Anker Innovations Limited temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Short-Term Confidential exhibits are listed as follows:

PERMANENT AND SHORT-TERM CONFIDENTIAL LIST Description Exhibit PERMANENT SHORT-TERM 1 2 3 4 5 6 7 8 Block Diagram Operational Description Schematics BOM External Photos Internal Photos Test-Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Signatory Namelouis Qi Company nameAnker Innovations Limited AddressRoom 1318-19,Hollywood Plaza,610 Nathan Road,Mongkok,Kowloon,Hong Kong Tel+86-13652441319 Emaillouis.qi@oceanwing.com

Anker Innovations Limited Date: 2020/4/20 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:

for an FCC equipment authorization The Anker Innovations Limited, the undersigned, hereby authorizes Mrs. Wendy Zhan from Shenzhen Morlab Communications Technology Co., Ltd., to act on the behalf of the Anker Innovations Limited solely in matters relating to the application ID:2AOKB-T8321M including the signing of documents in connection with this Application. Necessary acts carried out Shenzhen Morlab Communications Technology Co., Ltd. on our behalf of the Anker Innovations Limited in connection with the Application shall have the same effect as acts of the Anker Innovations Limited.Anker Innovations Limited also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. for FCC Thank you for your attention to this matter. Yours Sincerely, Signatory:

Contact name: louis Qi Title:NA Tel:+86-13652441319 Email:louis.qi@oceanwing.com Company name: Anker Innovations Limited

Anker Innovations Limited Suppliers Declaration Of Conformity for the FCC SDoC Procedure The following Equipment adapt FCC SDoC Procedure according to FCC part 2.906 :

Product Name: ___Video Baby Monitor 720P___ Brand Name: ___eufy SECURITY___ Model Number: ___T8321-M____ Report Number: ___SZ20020089E02___ Its herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. It is understood that each unit marketed is identical to the device as tested, and any changes to the device that could adversely affect the emission characteristics will require retest. The following importer / responsible party in United States:

Company Address: Room 1318-19,Hollywood Plaza,610 Nathan Road,Mongkok,Kowloon,Hong Kong Not Available at Certification Stage Company Name: Anker Innovations Limited Telephone: +86-13652441319 Fax: /

Person is responsible for marking this declaration:

Louis Qi ____________________________________ Name (Full name)Position / Title ______________________________________ ____________________________________ Legal Signature 2020-4-20 ______________________________________ Date