QUICK
START GUIDE
Video Doorbell 1080p (Battery-Powered)
Anker Innovations Limited. All rights reserved. eufy Security and eufy
Security Logo are trademarks of Anker Innovations Limited, registered in the
United States and other countries. All other trademarks are the property of
their respective owners.
51005002289 V01
TABLE OF
CONTENTS
What’s Included 01 09 Finding a Mounting Spot
Product Overview 03 11 Mounting the Bracket
How the System Works 04 14 Mounting the Doorbell
Powering on the Wi-Fi Doorbell Chime 05 15 Detaching the Doorbell
Setting up the System 07 16 Recharging the Doorbell
Charging Your Doorbell 08 17 Notice
WHAT’S INCLUDED
For Video Doorbell Installation
For Wi-Fi Doorbell Chime Installation
Video Doorbell 1080p
(Battery-Powered)
Model: T8222
FCC ID: 2AOKB-T8220
IC: 23451-T8220
Mounting Bracket
Screw Hole
Positioning Card
15° Mounting
Wedge
(Optional)
QSG
USB Charging
Cable
Screw Packs (Spare
screws and anchors are
included)
Doorbell
Detaching Pin
Quick Start
Guide
Model: Wi-Fi Doorbell Chime
Power Plug
FCC ID: 2AOKB-T8020
IC: 23451-T8020
Note: Power plug may vary in different regions.
01 English
English 02
PRODUCT OVERVIEW
Video Doorbell (Battery Powered)
Front view:
2
4
1
3
5
1. Motion Sensor
2. Microphone
3. Camera Lens
4. Ambient Light Sensor
5. Status LED
6. Doorbell Button
7. Speaker
7
Rear View:
6
1
2
3
1. Micro USB Charging Port
2. SYNC/RESET button
3. Detaching Mechanism
Operation
Power on
Add doorbell to Wi-Fi
Doorbell Chime
How-to
Press and release the SYNC button.
Press and hold the SYNC button until you hear a beep.
Power off the doorbell
Quick-press the SYNC 5 times in 3 seconds.
Reset the doorbell
Press and hold the SYNC button for 10 seconds.
03 English
HOW THE SYSTEM WORKS
How the System Works
The video doorbell system includes 2 parts:
• The video doorbell at your door
• The Wi-Fi Doorbell Chime in your house
The video doorbell detects motion at your porch and allows you to answer the door
anytime and anywhere. The Wi-Fi Doorbell Chime stores video clips on a microSD
card (user provides it) and works as an indoor digital chime. When someone rings
the doorbell, people in the house will be notified.
Doorbell Chime
Video Doorbell
English 04
2. Extend Wi-Fi Doorbell Chime’s antennas.
STEP 1 POWERING ON THE WI-FI
DOORBELL CHIME
Connect the HomeBase 2 to the Internet
1. Fix the power connector to Wi-Fi Doorbell Chime.
① Place the power connector over Wi-Fi Doorbell Chime in the direction the
② Align the raised slots of the power connector with the notch on the base of
arrows indicate.
the doorbell chime.
③ Rotate clockwise to lock the power connector in place.
1
2
3
3. Plug Wi-Fi Doorbell Chime into an AC power supply at your desired location.
The LED indicator turns solid green when the doorbell chime is ready for setup.
05 English
English 06
STEP 2 SETTING UP THE SYSTEM
Download the App and Set up the System
Download the eufy Security app from the App Store (iOS devices) or Google Play
(Android devices).
STEP 3 CHARGING YOUR
DOORBELL
The doorbell comes with an 80% battery level for safe transportation. Fully charge it
before mounting the doorbell at your front door.
Sign up for a eufy Security account and follow onscreen instructions to complete the
setup.
6 months
Tap Add Device and add the following devices:
1. Add the Wii-Fi Doorbell Chime.
2. Add the doorbell.
Note: The battery life varies depending on usage. In most common cases, a
doorbell may have up to 15 events per day and each recording lasts 20 seconds on
average. Under this scenario, the doorbell battery life can last up to 4 months.
07 English
English 08
STEP 4 FINDING A MOUNTING SPOT
Place the Screw Hole Positioning Card against the wall to mark the position.
Find a Mounting Spot
Take the Video Doorbell to your front door and check the live view on the eufy
Security app at the same time. Find a position where you can get the desired field of
view.
Consider the below factors:
1. Check if you can reuse the existing holes and anchors on the wall or door frame.
2.
If you want to place the doorbell close to a side wall, make sure the wall doesn’t
show up in the field of view. Otherwise IR light will be reflected and night vision
will become blurry.
3.
If you are drilling the mounting holes for the first time the recommended
mounting height is 48" / 1.2m from the ground.
4. Use the 15° mounting wedge as a supplementary mounting bracket if you wish to
see more on a specific side.
1.76m(5’9”)
1.2m (48")
1m
(40")
0.3m
(12")
Door
Video Doorbell
Door
Video Doorbell
15°
Without 15° Mounting wedge
With 15° Mounting wedge
09 English
English 10
STEP 5 MOUNTING THE BRACKET
Mount the Doorbell on a Wooden Surface
If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill
pilot holes. Use the provided screws to secure the Mounting Bracket on the wall.
The Screw Hole Positioning Card indicates the position of the screw holes.
Mount the Video Doorbell on Surfaces Made Out of
Hard Materials
1. If you’re mounting the doorbell on a surface made out of hard materials, like
brick, concrete, stucco, drill 2 holes through the Screw Hole Positioning Card
with 15/64”(6mm) drill bit.
2. Insert the provided anchors, and then use the provided long screws to secure the
Mounting Bracket on the wall.
What is required: Power Drill, Mounting Bracket, 15° Mounting Wedge
(Optional), Screw Packs
What is required: Power Drill, 15/64”(6mm) Drill Bit, Mounting Bracket, 15°
Mounting Wedge (Optional), Screw Packs
Phillips-Head Screwdriver
(User provides it.)
Mounting Bracket
(Attached to 15° Mounting Wedge)
15° Mounting
Wedge (Optional)
Screw Packs (Spare screws
and anchors are included.)
Power Drill with
1/4" (6.35mm) Drill Bit
Power Drill with
(User provides it.)
1/4" (6.35mm) Drill Bit
(User provides it.)
15/64”(6 mm) Drill Bit
Mounting Bracket
(Attached to 15° Mounting Wedge)
15° Mounting
Wedge (Optional)
Screw Packs (Spare screws
and anchors are included.)
15/64”(6 mm) Drill Bit
Mounting Bracket
(Attached to 15° Mounting Wedge)
15° Mounting
Wedge (Optional)
Screw Packs (Spare screws
and anchors are included.)
1
1
2
2
Wall
Mounting
Bracket
Wall
Mounting
Wedge
Mounting
Bracket
Without 15° Mounting Wedge
With 15° Mounting Wedge
11 English
Wall
Mounting
Bracket
Wall
Mounting
Wedge
Mounting
Bracket
Without 15° Mounting Wedge
With 15° Mounting Wedge
Wall
Mounting
Bracket
Wall
Mounting
Wedge
Mounting
Bracket
Without 15° Mounting Wedge
With 15° Mounting Wedge
English 12
Power Drill with
1/4" (6.35mm) Drill Bit
(User provides it.)
15/64”(6 mm) Drill Bit
Mounting Bracket
(Attached to 15° Mounting Wedge)
15° Mounting
Wedge (Optional)
Screw Packs (Spare screws
and anchors are included.)
1
2
Wall
Mounting
Bracket
Wall
Mounting
Wedge
Mounting
Bracket
Without 15° Mounting Wedge
With 15° Mounting Wedge
STEP 6 MOUNTING THE DOORBELL
Mount the Doorbell
Align the doorbell with the top of the mount and then snap the bottom into place.
You’re all set!
If you want to detach the doorbell or recharge it, please refer to the following
sections.
13 English
English 14
APPENDIX 1 DETACHING THE DOORBELL
Detach the Doorbell
the Mounting Bracket.
2. Insert and press the detaching pin into the hole on the bottom of the doorbell
and then lift to take the bottom of the doorbell off.
What is required: Doorbell Detaching Pin
APPENDIX 2 RECHARGING THE
DOORBELL
Charge the doorbell with universal USB chargers that deliver 5V 1A output.
1. Use the doorbell detaching pin provided if you wish to detach the doorbell from
Recharge the Doorbell
Doorbell
Detaching Pin
LED indication
Charging: Solid orange
Fully charged: Solid blue
Charging time
6 hours from 0% to 100%
15 English
English 16
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase
the separation between the equipment and receiver. (3) Connect the equipment
into an outlet on a circuit different from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio / TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device
can be used in fixed/mobile exposure condition. The min separation distance is 20cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to
maintain compliance with FCC regulations.
The following importer is the responsible party:
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: 1-800-988-7973
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU. For
the declaration of conformity, visit the Web site: https://www.eufylife.com/.
This product can be used across EU member states.
Do not use the Device in the environment at too high or too low temperature, never
expose the Device under strong sunshine or too wet environment.
The suitable temperature for T8020 and accessories is 0°C-40°C.
The suitable temperature for T8222 and accessories is -20°C-50°C.
When charging, please place the device in an environment that has a normal room
temperature and good ventilation.
It is recommended to charge the device in an environment with a temperature that
ranges from 5°C~25°C.
RF exposure information: The Maximum Permissible Exposure (MPE) level has been
calculated based on a distance of d=20 cm between the device and the human body. To
maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Wifi Operating Frequency Range: 2412~2472MHz (2.4G)
Wifi Max Output Power: 15.68dBm (ERIP for T8020); 15.01dBm (ERIP for T8220)
Bluetooth Operating Frequency Range: 2402~2480MHz; Bluetooth Max Output Power:
2.048dBm (EIRP)
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham,
B11 2AA, United Kingdom
This product is designed and manufactured with high quality materials and
components, which can be recycled and reused.
17 English
English 18
This symbol means the product must not be discarded as household waste,
and should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health
and the environment. For more information on disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you bought this product.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product, maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de
vous conformer aux exigences en matière d'exposition RF.
CUSTOMER SERVICE
Warranty
12-month limited warranty
(US) +1 (800) 988 7973 Mon-Fri 9:00-17:00 (PT)
(UK) + 44 (0) 1604 936 200 Mon-Fri 6:00-11:00 (GMT)
(DE) +49 (0) 69 9579 7960 Mon-Fri 6:00-11:00
Customer Support: support@eufylife.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon,
Hong Kong
19 English