FCC ID: 2AZ6P-1136234L Wireless Earphones

E-MAX SHADOWs PRO Contents A B C D E F G H A - EVA Carrying Case B - Rechargeable Storage Case C - *Foam Tips (4 Sets S,M,L-tapered and 1 cylindrical) D - Silicone Tips (3 Sets S,M,L) E - Lanyard F - USB-C Cable G - Right Earplug H - Left Earplug Product #1136234

*Use foam tips for hearing protection Media Controls Left Earplug Volume Up (VOL +) Volume Down (VOL - ) Multi-Function Button (MFB) Right Earplug Media Controls Action Function Press MFB Play/Pause Skip Forward Press VOL + for three seconds Skip Backward Press VOL - for three seconds Press VOL +

Volume Up Press VOL -

Volume Down Call Controls Function Answer Call End Call Ignore Call Voice Assistant Action Press MFB Press MFB Press MFB for one second Press MFB quickly three times Ambient Pass-Through Mode Ambient pass-through mode allows you to hear your surroundings while using foam ear tips to protect your hearing. Sounds picked up by microphones on the outside of the earplugs will be played through the speakers at a safe volume. The volume of the ambient pass-through is adjustable in this mode and can even be used to amplify your surroundings. If music is playing when ambient pass-through is enabled, the music volume will be reduced slightly. Microphones Action Function Enable/Disable Ambient Mode Double-Click MFB Volume Up Volume Down Press VOL +

Press VOL -

Charging Earplugs Push earplugs into case then close the lid and ear-

plugs will charge automatically. The LEDs will glow solid red when charging and turn green for 1 minute once fully charged. The LEDs inside the case indicate the charge level for each earplug. Left Earplug Charge Indicator Right Earplug Charge Indicator Charging Indicators USB-C Charging Port Charging the Case Charge the case with the included USB cable. The LEDs on the outside of the case indicate the charge level of the case. The top charge indicator LED will blink indicating that the case is charging. Pairing Earplugs 1. Place both earplugs in charging case to activate. 2. Remove both earplugs to begin pairing. 3. Search for E-MAX Shadows Pro on Bluetooth enabled device and tap to connect. Once paired, earplugs will power on automatically when removed from the charging case. If earplugs fail to power on automatically, fully charge them and try again. Switch Paired Device 1. Turn off Bluetooth on the device that you wish to disconnect. Earplugs will auto-disconnect and enter pairing mode. 2. On second device, search for E-MAX Shadows Pro and tap to connect.

*Multiple device connection is not supported. Earplugs will auto-reconnect to second device upon powering up again. Lanyard Attachment 1. Make a point with the lanyard loop end and push Troubleshooting

(Try the following steps to x connection issues). through the hole on the earplug. 1. With Left Earplug powered on, rmly press and hold VOL + and VOL down simultaneously for four seconds until the light ashes yellow then turns off. 2. With Right Earplug powered on, press and hold MFB for 4 seconds until light turns red and then turns off. 3. Place both Left and Right Earplugs into charging case and close the lid. 4. Open the lid and remove both Left and Right Earplugs from the case simultaneously. 2. Make a large loop and pull around the earplug. 3. Pull the lanyard closing the loop and making a snug knot. 4. Repeat for the other side. How to Wear Choose the ear tips that best t you. The silicone ear tips are best suited for sports and recreation. Foam ear tips must be used for hearing protection. FOR MAXIMUM HEARING PROTECTION, FOAM EAR TIPS MUST BE WORN. Ensure that the earplug labeled "R" is inserted into the right ear and the earplug labeled "L" is inserted into the left ear. Compress the foam before inserting the foam ear tips into your ear canal. Support the earplug in your ear for a few seconds while the foam expands, sealing your ear canal and protecting your hearing. CAUTION: For noise environments dominated by frequencies below 500Hz, the C-weighted environment noise level should be used. Although hearing protectors can be recommended for protection against the harmful effects of impulsive noise, the reduction rating (NRR) is based on the attenuation of continuous noise and may not be an accurate indicator of the protection attainable against impulsive noise such as gunre. FCC Statement:

This device complies with Part 15 of the FCC rules. Op-

eration is subject to the following two conditions: 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to pro-

vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will NRR = 25 dB Tested in accordance with ANSI S3.19-1974 In-ear The NRR calculated from these laboratory-based attenuation data is 25 Improper t of this device will reduce its effectiveness in attenuating noise. Consult instructions for proper t. The level of noise entering a persons ears when a hearing protector is worn as directed is closely approximated by the difference between the A-weighted environmental noise level and the NRR. Examples 1. The environmental noise level as measured at the ear is 91 dB(A). 2. The NRR is 25 decibels (dB). 3. The level of noise entering the ear is approximately equal to [91 dB - 25] 66 dB(A). not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into and outlet on a circuit differ-

ent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Left earphone FCC ID:2AZ6P-1136234L Right earphone FCC ID:2AZ6P-1136234R Tips Before use, please read the manual carefully and keep for future reference. Charge earplugs completely before rst use. If the earplugs cannot be found by your device, check the charge level by returning the earplugs to the charging case. Try pairing again when the earplugs are fully charged. Warnings Never disassemble or modify your earplugs or charging case for any reason. Do not store earplugs or charging case in extreme temperatures (Below 32F or above 110F). Recharge fully before use if the earplugs are left unused for over two weeks. Do not use harsh chemicals to clean earplugs or charging case. Keep earplugs and charging case dry. WARNING: Read all instructions and warnings before using this product; failure to follow warnings may result in serious personal injury, including hearing loss. Specications Pairing Name: E-Max Shadows Pro Bluetooth Version: 5.0 Standby Time: 35 hours Charging Time: 2 hours Music Time: 6 hours Bluetooth Range: 10m (with no obstacles) Battery Type: Lithium Ion Battery Capacity (Earplug): 3.7V 60mAh Battery Capacity (Case): 3.7V 700mAh USB Charging Input: 5V 1A Bluetooth Proles: HSP/HFP/A2DP/AVRCP Instructions #1156068 VER. 003

November 30, 2027 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Actas Agent On our behalf, | appoint___Qianhai BlueAsia of Technical Serivices(shenzhen) Limited, No 448, BulongRoad_ BantianStreet,LonggangDistric (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. | certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized:agent signs the application for:certification on ourbehaif,.|

acknowledge that all responsibility for complying with the terms and conditionsfor certification, still esides with AOB Products Company, 1800 North Route Z Suite A Columbia, MO 65202 United States(Applicant Name and address)

<Signature> MS [, Name : Michael Galloway Title : Quality Engineer Supervisor Company : : AOB Products Company

November 30, 2027 Equipment Autorisation Division Federal Communications Commission 7435 Oakiand Mills Road Columbia, MD 21046 FCC ID:2AZ6P-1136234L Product Name:Wireless Earphones Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ...) e Schematics e Block diagram e Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors.

<Signature> [, Name : Michael Galloway Title : Quality Engineer Supervisor Company : AOQB Products Company