| submitted | available | document details (if available) | source link |
|---|---|---|---|
| November 09 2017 | December 09 2017 |
| various | 2G3G Test Report | Test Report | 1.36 MiB | November 09 2017 / December 09 2017 |
PCTEST ENGINEERING LABORATORY, INC. 18855 Adams Court, Morgan Hill, CA 95037 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com Applicant Name:
Apple Inc. 1 Infinite Loop Cupertino, CA 95014 United States F C C I D :
A P P L I C A N T :
Application Type:
Model:
EUT Type:
FCC Classification:
FCC Rule Part(s):
Test Procedure(s):
MEASUREMENT REPORT FCC Part 22 Date of Testing:
6/9-8/4/2017 Test Site/Location:
PCTEST Lab., Morgan Hill, CA, USA Test Report Serial No.:
1C1706160002-91-02-R5.BCG BCG-A1891 APPLE INC. Certification A1891, A1972 Watch Licensed Non-Broadcast Transmitter Worn on Body (TNT) 2; 22(H) ANSI/TIA-603-E-2016, KDB 971168 D01 v02r02, KDB 648474 D03 v01r04, KDB 414788 D01 Radiated Test Site v01 Test Device Serial No.:
identical prototype [S/N: FH7TR00EJ79T, FH7TR007J7C3]
This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in 2.947. Test results reported herein relate only to the item(s) tested. This revised Test Report (S/N: 1C1706160002-91-02-R5.BCG) supersedes and replaces the previously issued test report (S/N:
1C1706160002-91-02-R4.BCG) on the same subject device for the same type of testing as indicated. Please discard or destroy the previously issued test report(s) and dispose of it accordingly. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) EUT Type:
FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
Approved by:
Quality Manager Page 1 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. T A B L E O F C O N T E N T S 2.0 3.0 FCC PART 22 MEASUREMENT REPORT .................................................................................................. 3 1.0 INTRODUCTION .............................................................................................................................. 5 Scope ................................................................................................................................................... 5 1.1 1.2 Testing Facility ..................................................................................................................................... 5 PRODUCT INFORMATION .............................................................................................................. 6 Equipment Description ......................................................................................................................... 6 2.1 Device Capabilities .............................................................................................................................. 6 2.2 2.3 Antenna Configuration ......................................................................................................................... 6 Test Support Equipment ...................................................................................................................... 6 2.4 Test Configuration ................................................................................................................................ 7 2.5 2.6 Software and Firmware ........................................................................................................................ 7 2.7 EMI Suppression Device(s)/Modifications ............................................................................................ 7 DESCRIPTION OF TESTS .............................................................................................................. 8 3.1 Evaluation Procedure ........................................................................................................................... 8 Cellular - Base Frequency Blocks ........................................................................................................ 8 3.2 Cellular - Mobile Frequency Blocks ...................................................................................................... 8 3.3 3.4 Radiated Measurements ...................................................................................................................... 9 MEASUREMENT UNCERTAINTY ................................................................................................. 10 TEST EQUIPMENT CALIBRATION DATA .................................................................................... 11 SAMPLE CALCULATIONS ............................................................................................................ 12 TEST RESULTS ............................................................................................................................. 13 Summary ............................................................................................................................................ 13 7.1 Occupied Bandwidth .......................................................................................................................... 14 7.2 7.3 Spurious and Harmonic Emissions at Antenna Terminal ................................................................... 16 Band Edge Emissions at Antenna Terminal ....................................................................................... 22 7.4 ERP ................................................................................................................................................... 24 7.5 7.6 Radiated Spurious Emissions Measurements Above 1 GHz .......................................................... 27 Radiated Spurious Emissions Measurements Below 1 GHz ........................................................... 30 7.7 7.8 Frequency Stability / Temperature Variation ...................................................................................... 33 CONCLUSION ................................................................................................................................ 36 4.0 5.0 6.0 7.0 8.0 FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 2 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. MEASUREMENT REPORT FCC Part 22 FCC ID:
TEST SITE:
APPLICANT:
BASE MODEL:
FCC RULE PART(S):
TEST SITE ADDRESS:
FCC CLASSIFICATION:
APPLICANT ADDRESS:
Apple Inc. 1 Infinite Loop Cupertino, CA 95014, United States PCTEST ENGINEERING LABORATORY, INC. 18855 Adams Court, Morgan Hill, CA 95037 USA 2 22(H) A1891, A1972 BCG-A1891 Licensed Non-Broadcast Transmitter Worn on Body (TNT) WCDMA 2.1033 General Information Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Morgan Hill, CA 95037, U.S.A. PCTEST is an ISO 17025-2005 accredited test facility under the American Association for Laboratory Accreditation (A2LA) with Certificate number 2041.02 for Specific Absorption Rate (SAR), Hearing Aid Compatibility (HAC) testing, where applicable, and Electromagnetic Compatibility (EMC) testing for FCC and Innovation, Science, and Economic Development Canada rules. FH7TR00EJ79T, FH7TR007J7C3 6/9-8/4/2017 1C1706160002-91-02-R5.BCG MODE:
FREQUENCY TOLERANCE: 0.00025 % (2.5 ppm) Test Device Serial No.:
Pre-Production TEST REPORT S/N:
DATE(S) OF TEST:
Production Engineering PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC 17065-2012 by A2LA (Certificate number 2041.03) in all scopes of FCC Rules and ISED Standards (RSS). PCTEST facility is a registered (22831) test laboratory with the site description on file with ISED. FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 3 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. MEASUREMENT REPORT FCC Part 22 EUT Overview FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 4 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. WCDMA85022H826.4 - 846.60.001441.574M15F9WEmission DesignatorTx Frequency (MHz)ERPMax. Power (W)Max. Power (dBm)ModeFCC Rule Part 1 . 0 I N T R O D U C T I O N Scope 1.1 Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Innovation, Science, and Economic Development Canada. 1.2 These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 18855 Adams Court, Morgan Hill, CA 95037. Testing Facility FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Approved by:
Quality Manager Page 5 of 36 V 6.6 06/06/2017 2 . 0 P R O D U C T I N F O R M A T I O N Device Capabilities Equipment Description 2.1 The Equipment Under Test (EUT) is the Apple Watch FCC ID: BCG-A1891. The test data contained in this report pertains only to the emissions due to the EUTs 2G/3G licensed transmitters. According to the manufacturer, models A1891 and A1972 are electrically identical. Model A1891 was used for final testing. 2.2 This device contains the following capabilities:
850 WCDMA/HSPA, Multi-band LTE, 802.11b/g/n WLAN, Bluetooth (1x, EDR, LE), NFC 2.3 Following antenna gain was used for the testing. Antenna Configuration Table 2-1. Peak Antenna Gain Test Support Equipment 2.4 Table 2-2. Test Support Equipment Used FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 6 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Frequency (MHz)Antenna Gain (dBi)824-849-20.781 Apple MacBookModel:A1502S/N:C02NQ01YG465w/ AC/DC AdapterModel:A1435S/N:C04325505K1F288BG2Apple USB CableModel:KanziS/N:20153Dw/ Charging DockModel:FAPS61S/N:6304000736w/ DockModel:X241S/N:SJH3002AP2AS3USB Cable Model:N/AS/N:N/AShielded USB Cable 4w/ AC AdapterModel:B353S/N:N/A5Test Pathfinder Board Model:X988S/N:FGH7648700BDHMV3236Wireless Charging Pad (WCP)Model:A1598FCC ID:BCGA1598 Test Configuration 2.5 The EUT was tested per the guidance of ANSI/TIA-603-E-2016 and KDB 971168 D01 v02r02. See Section 7.0 of this test report for a description of the radiated and antenna port conducted emissions tests. This device supports wireless charging capability and, thus, is subject to the test requirements of KDB 648474 D03 v01r04. Additional radiated spurious emissions measurements were performed with the EUT on a certified wireless charging pad (WCP) while operating under normal conditions in a simulated call or data transmission configuration. The worst case radiated emissions data is shown in this report. The worst case configuration was investigated for all combinations of the three materials, aluminum, ceramic, and stainless steel, and various types of wristbands, metal and non-metal wrist bands. The store display sample was investigated with the three types of EUTs. The EUT was also investigated with and without wireless charger. The worst case configuration found was used for all testing. The worst case material was aluminum. The worst case accessory was metal wristband but no significant difference was found between various types of wrist bands. The emissions below 1GHz and above 18GHz were tested with the highest transmitting power channel and the worst case configuration. The EUT was manipulated through three orthogonal planes of X-orientation (flatbed), Y-orientation
(landscape), and Z-orientation (portrait) during the testing. Only the worst case emissions were reported in this test report. The worst orientation was found to be X-orientation (flatbed). 2.6 The test was conducted with firmware version 15R328 installed on the EUT. For conducted spurious emissions, automated test software was used to measure emissions and capture the corresponding plots necessary to show compliance. The measurement software utilized is PCTEST 2G/3G Automation, Version 3.9. 2.7 No EMI suppression device(s) were added and no modifications were made during testing. EMI Suppression Device(s)/Modifications Software and Firmware FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 7 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. 3 . 0 D E S C R I P T I O N O F T E S T S 894 A B 890 880 BLOCK 4: 891.5 894 MHz (B*) Evaluation Procedure A* B*
High BLOCK 3: 890 891.5 MHz (A* High) Cellular - Base Frequency Blocks Cellular - Mobile Frequency Blocks 3.1 The measurement procedures described in the Land Mobile FM or PM Communications Equipment Measurements and Performance Standards (ANSI/TIA-603-E-2016) and Measurement Guidance for Certification of Licensed Digital Transmitters (KDB 971168 D01 v02r02) were used in the measurement of the EUT. Deviation from Measurement Procedure..None 3.2 22.905 A*
Low 869 BLOCK 1: 869 880 MHz (A* Low + A) BLOCK 2: 880 890 MHz (B) 3.3 22.905 A*
Low 824 BLOCK 1: 824 835 MHz (A* Low + A) BLOCK 2: 835 845 MHz (B) BLOCK 4: 846.5 849 MHz (B*) BLOCK 3: 845 846.5 MHz (A* High) A* B*
High B A 835 845 849 FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 8 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Radiated Measurements 3.4 2.1053 22.913(a.2) 22.917(a) The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. The test site inside the chamber is a 6m x 5.2m elliptical, obstruction-free area in accordance with Figure 5.7 of Clause 5 in ANSI C63.4-2014. Absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections for measurements above 1GHz. For measurements below 1GHz, the absorbers are removed. A raised turntable is used for radiated measurement. The turn table is a continuously rotatable, remote-controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. An 80cm high Styrodur Plastic Test Table is placed on top of the turntable. The equipment under test was transmitting while connected to its integral antenna and is placed on a turntable 3 meters from the receive antenna. The receive antenna height is adjusted between 1 and 4 meter height, the turntable is rotated through 360 degrees, and the EUT is manipulated through all orthogonal planes representative of its typical use to achieve the highest reading on the receive spectrum analyzer. Per the guidance of ANSI/TIA-603-E-2016, a half-wave dipole is then substituted in place of the EUT. For emissions above 1GHz, a horn antenna is substituted in place of the EUT. The substitute antenna is driven by a signal generator with the level of the signal generator being adjusted to obtain the same receive spectrum analyzer level previously recorded from the spurious emission from the EUT. The power of the emission is calculated using the following formula:
Pd [dBm] = Pg [dBm] cable loss [dB] + antenna gain [dBd/dBi]
Where, Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] cable loss [dB]. Radiated power and radiated spurious emission levels are investigated with the receive antenna horizontally and vertically polarized per ANSI/TIA-603-E-2016. FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 9 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. 4 . 0 M E A S U R E M E N T U N C E R T A I N T Y The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI C63.4-2014. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95% level of confidence. The measurement uncertainty shown below meets or exceeds the UCISPR measurement uncertainty values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to determine compliance. Contribution Expanded Uncertainty (dB) Conducted Bench Top Measurements Radiated Disturbance (<1GHz) Radiated Disturbance (>1GHz) Radiated Disturbance (>18GHz) 1.13 4.98 5.07 5.09 FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 10 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. 5 . 0 T E S T E Q U I P M E N T C A L I B R A T I O N D A T A Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Measurements antennas used during testing were calibrated in accordance to the requirements of ANSI C63.5-2006. Table 5-1. Test Equipment FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 11 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number -AM LTx1Licensed Transmitter Cable Set3/17/2017Annual3/17/2018AM LTX1-EMI 3117-ESW1Radiated Cable Set3/1/2017Biennial3/1/2018N/A-EMI HL562E-ESW1Radiated Cable Set2/28/2017Biennial2/28/2018N/AESPECSU-241Temperature Chamber3/10/2017Annual3/10/201892009574Keysight Technologies N9030A 3Hz-44GHz PXA Signal Analyzer 3/13/2017Annual 3/13/2018MY49430244 PasternackNC100Torque Wrench8/21/2015Biennial8/21/201781968Rohde & Schwarz CMW500 Wideband Radio Communication Tester 1/10/2017Annual 1/10/2018161675Rohde & Schwarz CMW500 Wideband Radio Communication Tester 5/8/2017Annual 5/8/2018161616-DFRohde & Schwarz ESW26 ESW26 EMI Test Receiver 1/20/2017Annual 1/20/2018101299Rohde & Schwarz HL562EBi-Log Antenna (30MHz - 6GHz)1/19/2017Annual1/19/2018100610Rohde & Schwarz OSP130Open Switch and Control Unit1/18/2017Annual1/18/2018100970Rohde & Schwarz SFUNIT-RXTS-SFUNIT SHIELDED FILTER UNIT2/3/2017Annual2/3/2018102131Rohde & Schwarz TS-PR8Pre-Amplifier (30MHz - 8GHz)2/3/2017Annual 2/3/2018102325Rohde & Schwarz TC-TA18CROSS POL. VIVALDI ANT (400MHz - 18GHz)11/8/2016Annual11/8/2017101056-AETraceable1208T91Humidity/Temperature/Dew Point Meter9/27/2017Biennial9/27/2018160838829 6 . 0 S A M P L E C A L C U L A T I O N S WCDMA Emission Designator Emission Designator = 4M16F9W WCDMA BW = 4.16 MHz F = Frequency Modulation 9 = Composite Digital Info W = Combination (Audio/Data) Spurious Radiated Emission Example: Spurious emission at 3700.40 MHz The receive spectrum analyzer reading at 3 meters with the EUT on the turntable was 81.0 dBm. The gain of the substituted antenna is 8.1 dBi. The signal generator connected to the substituted antenna terminals is adjusted to produce a reading of 81.0 dBm on the spectrum analyzer. The loss of the cable between the signal generator and the terminals of the substituted antenna is 2.0 dB at 3700.40 MHz. So 6.1 dB is added to the signal generator reading of 30.9 dBm yielding 24.80 dBm. The fundamental EIRP was 25.50 dBm so this harmonic was 25.50 dBm (-24.80) = 50.3 dBc. FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 12 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. 7 . 0 T E S T R E S U L T S 7.1 Summary Company Name:
Apple Inc. FCC ID:
BCG-A1891 FCC Classification:
Licensed Non-Broadcast Transmitter Worn on Body (TNT) Mode(s):
FCC Part Section(s) WCDMA Test Description Test Limit Test Test Condition Result Reference 2.1049 Occupied Bandwidth N/A PASS Section 7.2 2.1051, 22.917(a) Conducted Band Edge /
Spurious Emissions
> 43 + log10 (P[Watts]) at Band Edge and for all out-of-band emissions 2.1046 Transmitter Conducted Output Power N/A CONDUCTED PASS PASS Sections 7.3, 7.4 RF Exposure Report 22.913(a.2) Effective Radiated Power
<7 Watts Max. ERP PASS Section 7.5 2.1055, 22.355 Frequency Stability
< 2.5 ppm (Part 22) PASS Section 7.8 2.1053, 22.917(a) Radiated Spurious Emissions
> 43 + log10 (P[Watts]) for all out-of-band emissions PASS Section 7.6 RADIATED Notes:
1) All modes of operation and data rates were investigated. The test results shown in the following Table 7-1. Summary of Test Results sections represent the worst case emissions. 2) The analyzer plots were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables, directional couplers, and attenuators used as part of the system to maintain a link between the call box and the EUT at all frequencies of interest. 3) All antenna port conducted emissions testing was performed on a test bench with the antenna port of the EUT connected to the spectrum analyzer through calibrated cables, attenuators, and couplers. 4) For conducted spurious emissions, automated test software was used to measure emissions and capture the corresponding plots necessary to show compliance. The measurement software utilized is PCTEST 2G/3G Automation, Version 3.9. FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 13 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. 7.2 Occupied Bandwidth 2.1049 Test Overview The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured. All modes of operation were investigated and the worst case configuration results are reported in this section. Test Procedure Used KDB 971168 D01 v02r02 Section 4.2 Test Settings 1. The signal analyzers automatic bandwidth measurement capability was used to perform the 99%
occupied bandwidth and the 26dB bandwidth. The bandwidth measurement was not influenced by any intermediate power nulls in the fundamental emission. 2. RBW = 1 5% of the expected OBW 3. VBW 3 x RBW 4. Detector = Peak 5. Trace mode = max hold 6. Sweep = auto couple 7. The trace was allowed to stabilize 8. If necessary, steps 2 7 were repeated after changing the RBW such that it would be within 1 5% of the 99% occupied bandwidth observed in Step 7 Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Test Notes None. FCC ID: BCG-A1891 Figure 7-1. Test Instrument & Measurement Setup FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
Approved by:
Quality Manager Page 14 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Plot 7-1. Occupied Bandwidth Plot (Cellular WCDMA Mode Ch. 4183) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 15 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Spurious and Harmonic Emissions at Antenna Terminal 7.3 2.1051, 22.917(a) Test Overview The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. All out of band emissions are measured with a spectrum analyzer connected to the antenna terminal of the EUT while the EUT is operating at maximum power, and at the appropriate frequencies. All data rates were investigated to determine the worst case configuration. All modes of operation were investigated and the worst case configuration results are reported in this section. The minimum permissible attenuation level of any spurious emission is 43 + log10(P[Watts]), where P is the transmitter power in Watts. Test Procedure Used KDB 971168 D01 v02r02 Section 6.0 Test Settings 1. Start frequency was set to 30MHz and stop frequency was set to 10GHz for Cell, 20GHz for AWS, 20GHz for PCS (separated into at least two plots per channel) 2. Detector = RMS 3. Trace mode = trace average 4. Sweep time = auto couple 5. The trace was allowed to stabilize 6. Please see test notes below for RBW and VBW settings Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-2. Test Instrument & Measurement Setup Test Notes Compliance with the applicable limits is based on the use of measurement instrumentation employing a resolution bandwidth of 100 kHz for Part 22 measurements below 1GHz. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 16 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Plot 7-2. Conducted Spurious Plot (Cellular WCDMA Mode Ch. 4132) Plot 7-3. Conducted Spurious Plot (Cellular WCDMA Mode Ch. 4132) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 17 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Plot 7-4. Conducted Spurious Plot (Cellular WCDMA Mode Ch. 4132) Plot 7-5. Conducted Spurious Plot (Cellular WCDMA Mode Ch. 4183) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 18 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Plot 7-6. Conducted Spurious Plot (Cellular WCDMA Mode Ch. 4183) Plot 7-7. Conducted Spurious Plot (Cellular WCDMA Mode Ch. 4183) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 19 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Plot 7-8. Conducted Spurious Plot (Cellular WCDMA Mode Ch. 4233) Plot 7-9. Conducted Spurious Plot (Cellular WCDMA Mode Ch. 4233) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 20 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Plot 7-10. Conducted Spurious Plot (Cellular WCDMA Mode Ch. 4233) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 21 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Band Edge Emissions at Antenna Terminal 7.4 2.1051, 22.917(a) Test Overview All out of band emissions are measured with a spectrum analyzer connected to the antenna terminal of the EUT while the EUT is operating at maximum power, and at the appropriate frequencies. All data rates were investigated to determine the worst case configuration. All modes of operation were investigated and the worst case configuration results are reported in this section. The minimum permissible attenuation level of any spurious emission is 43 + log10(P[Watts]), where P is the transmitter power in Watts. Test Procedure Used KDB 971168 D01 v02r02 Section 6.0 Test Settings 1. Start and stop frequency were set such that the band edge would be placed in the center of the plot 2. Span was set large enough so as to capture all out of band emissions near the band edge 3. RBW > 1% of the emission bandwidth 4. VBW > 3 x RBW 5. Detector = RMS 6. Number of sweep points 2 x Span/RBW 7. Trace mode = trace average 8. Sweep time = auto couple 9. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-3. Test Instrument & Measurement Setup Test Notes Per 22.917(b) in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed to demonstrate compliance with the out-of-band emissions limit. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 22 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. FCC ID: BCG-A1891 Plot 7-11. Band Edge Plot (Cellular WCDMA Mode Ch. 4132) Plot 7-12. Band Edge Plot (Cellular WCDMA Mode Ch. 4233) FCC Pt. 22 WCDMA MEASUREMENT REPORT EUT Type:
(CERTIFICATION) Approved by:
Quality Manager Page 23 of 36 V 6.6 06/06/2017 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. ERP 7.5 22.913(a)(2) Test Overview Effective Radiated Power (ERP) is specified when the operating frequency is less than or equal to 1 GHz. It is determined by adding the transmit antenna gain to the conducted RF output power. When determining the ERP, the transmit antenna gain is referenced to a dipole antenna (i.e., dBd). Test Procedures Used KDB 971168 D01 v02r02 Section 5.6 Test Formula:
The relevant equation for determining the ERP from the conducted RF output power measured is:
ERP = PMeas LC + GT where:
ERP = effective radiated power (expressed in the same units as PMeas, typically dBW or dBm);
PMeas = measured transmitter output power or PSD, in dBm or dBW;
LC = signal attenuation in the connecting cable between the transmitter and antenna, in dB GT = gain of the transmitting antenna, in dBd (ERP);
Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-4. ERP Measurement Setup FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 24 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Notes 1) This device employs UMTS technology with WCDMA (AMR/RMC) and HSDPA capabilities. The EUT was tested under all configurations and the highest power is reported in WCDMA mode with HSDPA Inactive at 12.2 kbps RMC and TPC bits all set to "1."
2) This unit was tested with its standard battery. 3) The Level (dBm) readings in the table were taken with a correction table loaded into the base station simulator. The correction table was used to account for the signal attenuation in the connecting cable between the transmitter and antenna. 4) The Ant. Gains (GT) are listed in dBi. 5) The final ERP values in dBm values were calculated in column 5. 6) The LC cable loss factor is already included in the measurement system and the conducted power in the table already includes this factor. FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 25 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Table 7-2. ERP (Cellular WCDMA) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 26 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. 826.40WCDMA85024.44-22.931.510.0014238.45-36.94836.60WCDMA85024.50-22.931.570.0014438.45-36.88846.60WCDMA85024.49-22.931.560.0014338.45-36.89Conducted Power [dBm]Ant. Gain [dBd]ERP [dBm]ERP [Watts]ERP Limit [dBm]Margin [dB]Frequency [MHz]ModeSub. Ant. Radiated Spurious Emissions Measurements Above 1 GHz 7.6 2.1053, 22.917(a) Test Overview Radiated spurious emissions measurements are performed using the substitution method described in ANSI/TIA-603-E-2016 with the EUT transmitting into an integral antenna. Measurements on signals operating below 1GHz are performed using horizontally and vertically polarized tuned dipole antennas. Measurements on signals operating above 1GHz are performed using vertically and horizontally polarized broadband horn antennas. All measurements are performed as peak measurements while the EUT is operating at maximum power, and at the appropriate frequencies. Test Procedures Used KDB 971168 D01 v02r02 Section 5.8 ANSI/TIA-603-E-2016 Section 2.2.12 Test Settings 1. RBW = 1MHz 2. VBW 3 x RBW 3. Span = 1.5 times the OBW 4. No. of sweep points > 2 x span / RBW 5. Detector = RMS 6. Trace mode = Average (Max Hold for pulsed emissions) 7. The trace was allowed to stabilize FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 27 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-5. Test Instrument & Measurement Setup Test Notes 1) This device employs UMTS technology with WCDMA (AMR/RMC) and HSDPA capabilities. The EUT was tested under all configurations and the highest power is reported in WCDMA mode with HSDPA Inactive at 12.2 kbps RMC and TPC bits all set to "1."
2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case setup is reported in the tables below. 4) The spectrum is measured from 9kHz to the 10th harmonic of the fundamental frequency of the transmitter. The worst-case emissions are reported. 5) Emissions below 18GHz were measured at a 3 meter test distance while emissions above 18GHz were measured at a 1 meter test distance with the application of a distance correction factor. 6) The "-" shown in the following RSE tables are used to denote a noise floor measurement. FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
Approved by:
Quality Manager Page 28 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Table 7-3. Radiated Spurious Data (Cellular WCDMA Mode Ch. 4132) Table 7-4. Radiated Spurious Data (Cellular WCDMA Mode Ch. 4183) Table 7-5. Radiated Spurious Data (Cellular WCDMA Mode Ch. 4233) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 29 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. OPERATING FREQUENCY: 826.40MHzCHANNEL: 4132MODULATION SIGNAL: WCDMADISTANCE: 3metersLIMIT: -13dBm1652.80H---78.736.98-71.75-58.7Frequency [MHz]Ant. Pol. [H/V]Antenna Height [cm]Turntable Azimuth [degree]Level at Antenna Terminals [dBm]Substitute Antenna Gain [dBd]Spurious Emission Level [dBm]Magrin [dB]OPERATING FREQUENCY: 836.60MHzCHANNEL: 4183MODULATION SIGNAL: WCDMADISTANCE: 3metersLIMIT: -13dBm1673.20H---78.256.85-71.41-58.4Frequency [MHz]Ant. Pol. [H/V]Antenna Height [cm]Turntable Azimuth [degree]Level at Antenna Terminals [dBm]Substitute Antenna Gain [dBd]Spurious Emission Level [dBm]Magrin [dB]OPERATING FREQUENCY: 846.60MHzCHANNEL: 4233MODULATION SIGNAL: WCDMADISTANCE: 3metersLIMIT: -13dBm1693.20H---78.466.88-71.58-58.6Frequency [MHz]Ant. Pol. [H/V]Antenna Height [cm]Turntable Azimuth [degree]Level at Antenna Terminals [dBm]Substitute Antenna Gain [dBd]Spurious Emission Level [dBm]Magrin [dB]
Radiated Spurious Emissions Measurements Below 1 GHz 7.7 2.1053, 22.917(a) Test Overview Radiated spurious emissions measurements are performed using the substitution method described in ANSI/TIA-603-E-2016 with the EUT transmitting into an integral antenna. Measurements on signals operating below 1GHz are performed using horizontally and vertically polarized tuned dipole antennas. Measurements on signals operating above 1GHz are performed using vertically and horizontally polarized broadband horn antennas. All measurements are performed as peak measurements while the EUT is operating at maximum power, and at the appropriate frequencies. Test Procedures Used KDB 971168 D01 v02r02 Section 5.8 ANSI/TIA-603-E-2016 Section 2.2.12 Test Settings 1. RBW = 100kHz 2. VBW 3 x RBW 3. Span = 1.5 times the OBW 4. No. of sweep points > 2 x span / RBW 5. Detector = RMS 6. Trace mode = Average (Max Hold for pulsed emissions) 7. The trace was allowed to stabilize FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 30 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-6. Test Instrument & Measurement Setup Test Notes 1) This device employs UMTS technology with WCDMA (AMR/RMC) and HSDPA capabilities. The EUT was tested under all configurations and the highest power is reported in WCDMA mode with HSDPA Inactive at 12.2 kbps RMC and TPC bits all set to "1."
2) This unit was tested with its standard battery. 3) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case setup is reported in the tables below. 4) The spectrum is measured from 9kHz to the 10th harmonic of the fundamental frequency of the transmitter. The worst-case emissions are reported. 5) Emissions below 18GHz were measured at a 3 meter test distance while emissions above 18GHz were measured at a 1 meter test distance with the application of a distance correction factor. 6) The spurious emissions 20dB below the limit is not reported. FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 31 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Plot 7-13. Radiated Spurious Plot (Cellular WCDMA Mode Ch. 4183) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 32 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.
-80 -60 -40 -20 030M 5060 80100M200300400500 8001GLevel in dBmFrequency in HzPreview Result 1H-AVGPreview Result 1V-AVGCritical_Freqs AVGFCC Licensed RSEFinal_Result AVGFCC Licensed RSE Frequency Stability / Temperature Variation 7.8 2.1055, 22.355 Test Overview and Limit Frequency stability testing is performed in accordance with the guidelines of ANSI/TIA-603-E-2016. The frequency stability of the transmitter is measured by:
a.) Temperature: The temperature is varied from -30C to +50C in 10C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. For Part 22, the frequency stability of the transmitter shall be maintained within 0.00025% (2.5 ppm) of the center frequency. Test Procedure Used ANSI/TIA-603-E-2016 Test Settings 1. The carrier frequency of the transmitter is measured at room temperature (20C to provide a reference). 2. The equipment is turned on in a standby condition for fifteen minutes before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10C intervals ranging from -30C to +50C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. Test Setup The EUT was connected via an RF cable to a spectrum analyzer with the EUT placed inside an environmental chamber. Test Notes None FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 33 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Frequency Stability / Temperature Variation 2.1055, 22.355 Table 7-6. Frequency Stability Data (Cellular WCDMA Mode Ch. 4183) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 34 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. OPERATING FREQUENCY: 836,600,000HzCHANNEL: 4183REFERENCE VOLTAGE: VDCDEVIATION LIMIT: 0.00025% or 2.5 ppm100 %3.82 + 20836,599,921-79-0.0000094100 %- 30836,600,1031030.0000123100 %- 20836,600,1101100.0000131100 %- 10836,600,052520.0000062100 % 0836,599,742-258-0.0000308100 %+ 10836,599,664-336-0.0000402100 %+ 20836,599,850-150-0.0000179100 % + 30836,600,1391390.0000166100 %+ 40836,600,3963960.0000473100 %+ 50836,599,890-110-0.0000131BATT. ENDPOINT3.42+ 20836,600,1391390.0000166FREQUENCY (Hz)Freq. Dev. (Hz)Deviation (%)VOLTAGE (%)POWER (VDC)TEMP (oC)3.82 Frequency Stability / Temperature Variation 2.1055, 22.355 Figure 7-7. Frequency Stability Graph (Cellular WCDMA Mode Ch. 4183) FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 35 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.
-3.5-2.5-1.5-0.50.51.52.53.5Deviation (ppm)Temperature (C)Frequency Stability 8 . 0 C O N C L U S I O N The data collected FCC ID: BCG-A1891 complies with all the requirements of Parts 22 of the FCC rules. tested and show relate only item(s) that the to the Apple Watch FCC ID: BCG-A1891 Test Report S/N:
1C1706160002-91-02-R5.BCG 6/9-8/4/2017 Watch 2017 PCTEST Engineering Laboratory, Inc. Test Dates:
EUT Type:
FCC Pt. 22 WCDMA MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Page 36 of 36 V 6.6 06/06/2017 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.
This product uses the FCC Data API but is not endorsed or certified by the FCC