| submitted | available | document details (if available) | source link |
|---|---|---|---|
| October 09 2018 | December 09 2018 |
| various | Bluetooth HDR Test Report | Test Report | 3.60 MiB | October 09 2018 / December 09 2018 |
PCTEST ENGINEERING LABORATORY, INC. 18855 Adams Court, Morgan Hill, CA 95037 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com MEASUREMENT REPORT FCC PART 15.247 / ISED RSS-247 Bluetooth (HDR) Applicant Name:
Apple Inc. One Apple Park Way Cupertino, CA 95014 United States FCC ID:
IC:
APPLICANT:
Application Type:
Model/HVIN:
EUT Type:
Max. RF Output Power:
Frequency Range:
FCC Classification:
FCC Rule Part(s):
ISED Specification:
Test Procedure(s):
Date of Testing:
5/15 - 8/18/2018 Test Site/Location:
PCTEST Lab. Morgan Hill, CA, USA Test Report Serial No.:
1C1806040005-03.BCG BCG-A1977 579C-A1977 Apple Inc. Certification A1977 Watch 37.068 mW (15.69 dBm) Peak Conducted 2404 2478MHz Digital Transmission System (DTS) Part 15 Subpart C (15.247) RSS-247 Issue 2 ANSI C63.10-2013, KDB 558074 D01 v05, KDB 648474 D03 v01r04 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013 and KDB 558074 D01 v05. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 1 of 64 T A B L E O F C O N T E N T S 1.0 INTRODUCTION .......................................................................................................................................... 3 1.1 Scope ................................................................................................................................................................... 3 1.2 PCTEST Test Location ......................................................................................................................................... 3 1.3 Test Facility / Accreditations ................................................................................................................................. 3 2.0 PRODUCT INFORMATION .......................................................................................................................... 4 2.1 Equipment Description ......................................................................................................................................... 4 2.2 Device Capabilities ............................................................................................................................................... 4 2.3 Antenna Description ............................................................................................................................................. 5 2.4 Test Support Equipment ....................................................................................................................................... 5 2.5 Test Configuration ................................................................................................................................................ 5 2.6 Software and Firmware ........................................................................................................................................ 6 2.7 EMI Suppression Device(s)/Modifications ............................................................................................................ 6 3.0 DESCRIPTION OF TESTS .......................................................................................................................... 7 3.1 Evaluation Procedure ........................................................................................................................................... 7 3.2 AC Line Conducted Emissions ............................................................................................................................. 7 3.3 Radiated Emissions .............................................................................................................................................. 8 3.4 Environmental Conditions ..................................................................................................................................... 8 ANTENNA REQUIREMENTS ...................................................................................................................... 9 MEASUREMENT UNCERTAINTY ............................................................................................................. 10 TEST EQUIPMENT CALIBRATION DATA ................................................................................................ 11 TEST RESULTS ......................................................................................................................................... 12 7.1 Summary ............................................................................................................................................................ 12 7.2 6dB Bandwidth Measurement Bluetooth (HDR) .............................................................................................. 13 7.3 Output Power Measurement Bluetooth (HDR) ................................................................................................ 18 7.3.1 Peak Output Power Measurement - Bluetooth (HDR) .................................................................................... 19 7.3.2 Average Output Power Measurement - Bluetooth (HDR) ............................................................................... 20 7.4 Power Spectral Density Bluetooth (HDR) ........................................................................................................ 21 7.5 Conducted Emissions at the Band Edge ............................................................................................................ 29 7.6 Conducted Spurious Emissions .......................................................................................................................... 34 7.7 Radiated Spurious Emission Measurements ...................................................................................................... 42 7.8 Radiated Restricted Band Edge Measurements ................................................................................................. 51 7.9 Radiated Spurious Emissions Measurements Below 1GHz ............................................................................ 55 7.10 Line-Conducted Test Data .............................................................................................................................. 60 CONCLUSION ............................................................................................................................................ 64 4.0 5.0 6.0 7.0 8.0 FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 2 of 64 1.0 I N T R O D U C T I O N Scope 1.1 Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Innovation, Science and Economic Development Canada. PCTEST Test Location 1.2 These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 18855 Adams Court, Morgan Hill, CA 95037. The measurement facility is compliant with the test site requirements specified in ANSI C63.4-2014 and KDB 414788 D01 v01r01. 1.3 Measurements were performed at PCTEST Engineering Lab located in Morgan Hill, CA 95037, U.S.A. PCTEST is an ISO 17025-2005 accredited test facility under the American Association for Laboratory Accreditation (A2LA) with Certificate number 2041.02 for Specific Absorption Rate (SAR), Hearing Aid Compatibility (HAC) testing, where applicable, and Electromagnetic Compatibility (EMC) testing for FCC and Innovation, Science, and Economic Development Canada rules. Test Facility / Accreditations PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC 17065-2012 by A2LA
(Certificate number 2041.03) in all scopes of FCC Rules and ISED Standards (RSS). PCTEST facility is a registered (22831) test laboratory with the site description on file with ISED. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 3 of 64 2.0 P R O D U C T I N F O R M A T I O N 2.1 Equipment Description The Equipment Under Test (EUT) is the Apple Watch FCC ID: BCG-A1977. The data found in this test report was taken with the EUT operating in Bluetooth HDR mode. While in HDR mode, the Bluetooth transmitter hops pseudo-randomly between 75 channels, three of which are advertising channels. When the transmitter is hopping only between the three advertising channels, the EUT does not fall under the category of a hopper as defined in 15.247(a)(iii) which states that a frequency hopping systems in the 24002483.5 MHz band shall use at least 15 channels. As operation on only the advertising channels does not qualify the EUT as a hopper, the EUT is certified as a DTS device in this mode. The data found in this report is representative of the device when it transmits on its advertising channels. Typical Bluetooth operation is covered under the DSS report found with this application. Test Device Serial No.: C89WK00TK489, C89W900HJPMT 2.2 This device contains the following capabilities:
802.11b/g/n WLAN, Bluetooth (1x, EDR, HDR4, HDR8, LE), NFC Device Capabilities Ch. 1
:
38
:
75 Frequency (MHz) 2404
:
2441
:
2478 Table 2-1. Frequency / Channel Operations Table 2-2. Measured Duty Cycle FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 4 of 64 Duty Cycle (%)ePA100.0iPA100.0ePA100.0iPA100.0Maximum Achievable Duty CyclesHDR Mode4M8M Antenna Description 2.3 Following antenna was used for the testing. Frequency [GHz]
2.4 Antenna Gain
(dBi)
-12.3 Table 2-3. Antenna Peak Gain Note: This device is capable of operating in hopping and non-hopping mode. The EUT can hop between 75 different channels in the 2404 2478MHz band. 2.4 Test Support Equipment Table 2-4. Test Support Equipment Used Test Configuration 2.5 The EUT was tested per the guidance of ANSI C63.10-2013 and KDB 558074 D01 v05. ANSI C63.10-2013 was used to reference the appropriate EUT setup for radiated spurious emissions testing and AC line conducted testing. See Sections 3.2 for AC line conducted emissions test setups, 3.3 for radiated emissions test setups, and 7.2, 7.3, 7.4, 7.5, and 7.6 for antenna port conducted emissions test setups. The worst case configuration was investigated for various types of wristbands, metal and non-metal wristbands. The store display sample was investigated and determined as not the worst case. The EUT was also investigated with and without wireless charger. The worst case configuration found was used for all testing. The emissions below 1GHz and above 18GHz were tested with the highest transmitting power channel and the worst case configuration. The EUT was manipulated through three orthogonal planes of X-orientation (flatbed), Y-orientation (landscape), and Z-orientation (portrait) during the testing. Only the worst case emissions were reported in this test report. For AC line conducted and radiated test below 1GHz, following configuration were investigated and worst case was reported.
- EUT powered by AC/DC adaptor via USB cable with wire charger
- EUT powered by host PC via USB cable with wire charger FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 5 of 64 1Apple MacBookModel:A1398S/N:C2QKP008F6F3w/AC/DC AdapterModel:A1435S/N:2Apple USB CableModel:KanziS/N:316F8Aw/ Charging DockModel:FAPS73S/N:17242000868w/ DockModel:X241S/N:GW17E01ST283USB Lightning CableModel:N/AS/N:N/Aw/ AC AdapterModel:A1265S/N:1X0450PGS8QZ4Wireless Charging Pad (WCP)Model:DVT-1dS/N:DLC824401XHJLW04U5Test Pathfinder Mogao BoardModel:X920S/N:920-04087-03w/ EVT SiP CradleModel:X920S/N:PF 20166DC Power SupplyModel:KPS3010DS/N:N/A Software and Firmware 2.6 The test was conducted with firmware version wOS 5.0 installed on the EUT. 2.7 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 6 of 64 3.0 D E S C R I P T I O N O F T E S T S Evaluation Procedure AC Line Conducted Emissions 3.1 The measurement procedures described in the American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices (ANSI C63.10-2013) and the guidance provided in KDB 558074 D01 v05 were used in the measurement of the EUT. Deviation from measurement procedure.....................................None 3.2 The line-conducted facility is located inside a 7m x 3.66m x 2.7m shielded enclosure. The shielded enclosure is manufactured by AP Americas. The shielding effectiveness of the shielded room is in accordance with MIL-Std-
285 or NSA 65-6. A 1m x 1.5m wooden table 80cm high is placed 40cm away from the vertical wall and 80cm away from the sidewall of the shielded room. Two 10kHz-30MHz, 50/50H Line-Impedance Stabilization Networks (LISNs) are bonded to the shielded room floor. Power to the LISNs is filtered by external high-current high-insertion loss power line filters. The external power line filter is EPCOS 2X60A Power Line Filter (100dB Attenuation, 14kHz-18GHz) and the two EPCOs 2X48A filters (100dB Minimum Insertion Loss, 14kHz 10GHz). These filters attenuate ambient signal noise from entering the measurement lines. These filters are also bonded to the shielded enclosure. The EUT is powered from one LISN and the support equipment is powered from the second LISN. If the EUT is a DC-powered device, power will be derived from the source power supply it normally will be powered from and this supply line(s) will be connected to the second LISN. All interconnecting cables more than 1 meter were shortened to a 1 meter length by non-inductive bundling (serpentine fashion) and draped over the back edge of the test table. All cables were at least 40cm above the horizontal reference groundplane. Power cables for support equipment were routed down to the second LISN while ensuring that that cables were not draped over the second LISN. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the spectrum analyzer and exploratory measurements were made to determine the frequencies producing the maximum emission from the EUT. The spectrum was scanned from 150kHz to 30MHz with a spectrum analyzer. The detector function was set to peak mode for exploratory measurements while the bandwidth of the analyzer was set to 10kHz. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Once the worst case emissions have been identified, the one EUT cable configuration/arrangement and mode of operation that produced these emissions is used for final measurements on the same test site. The analyzer is set to CISPR quasi-peak and average detectors with a 9kHz resolution bandwidth for final measurements. Line conducted emissions test results are shown in Section 7.10. Automated test software was used to perform the AC line conducted emissions testing. Automated measurement software utilized is Rohde & Schwarz EMC32, Version 10.20.01. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 7 of 64 Radiated Emissions 3.3 The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. The test site inside the chamber is a 6m x 5.2m elliptical, obstruction-free area in accordance with Figure 5.7 of Clause 5 in ANSI C63.4-2014. Absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections for measurements above 1GHz. An 80cm tall test table made of Styrodur is placed on top of the turn table. For measurements above 1GHz, an additional Styrodur pedestal is placed on top of the test table to bring the total table height to 1.5m. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33 depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up was placed on top of the 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, mode of operation, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. 3.4 The temperature is controlled within range of 15oC to 35oC. The relative humidity is controlled within range of 10%
to 75%. The atmospheric pressure is monitored within the range 86-106kPa (860-1060mbar). Environmental Conditions FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 8 of 64 4.0 A N T E N N A R E Q U I R E M E N T S Excerpt from 15.203 of the FCC Rules/Regulations:
An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The antenna(s) of the EUT are permanently attached. There are no provisions for connection to an external antenna. Conclusion:
The EUT complies with the requirement of 15.203. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 9 of 64 5.0 M E A S U R E M E N T U N C E R T A I N T Y The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI C63.10-2013. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95% level of confidence. The measurement uncertainty shown below meets or exceeds the UCISPR measurement uncertainty values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to determine compliance. Contribution Expanded Uncertainty (dB) Conducted Bench Top Measurements Line Conducted Disturbance Radiated Disturbance (<1GHz) Radiated Disturbance (>1GHz) Radiated Disturbance (>18GHz) 1.13 3.09 4.98 5.07 5.09 FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 10 of 64 6.0 T E S T E Q U I P M E N T C A L I B R A T I O N D A T A Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Measurements antennas used during testing were calibrated in accordance to the requirements of ANSI C63.5-
2017. Table 6-1. Annual Test Equipment Calibration Schedule Note:
For equipment listed above that has a calibration date or calibration due date that falls within the test date range, care was taken to ensure that this equipment was used after the calibration date and before the calibration due date. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 11 of 64 Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number AnritsuML2495APower Meter11/28/2017Annual11/28/20181039008AnritsuMA2411BPower Sensor 10MHz-40GHz11/28/2017Annual11/28/20181027293COM-POWER LIN-120A LISN 3/7/2018Annual3/7/2019241296Keysight Technologies N9030A 3Hz-44GHz PXA Signal Analyzer 2/27/2018Annual2/27/2019MY49430244 MaturoNCD/264/205616Mast/TT controllerN/AN/AN/ANCD_264Rohde & Schwarz ESW44EMI Test Receiver12/20/2017Annual12/20/2018101668Rohde & Schwarz ESW44EMI Test Receiver11/16/2017Annual11/16/2018101570Rohde & SchwarzFSV40Signal Analyzer (10Hz-40GHz)2/6/2018Annual2/6/2019101619Rohde & Schwarz SFUNIT-RXShielded Filter Unit9/11/2017Annual9/11/2018102132Rohde & Schwarz SFUNIT-RXShielded Filter Unit12/11/2017Annual12/11/2018102136Rohde & Schwarz TS-PR1840Pre-Amplifier (18GHz - 40GHz)6/11/2018Annual 6/11/2019100051Rohde & Schwarz TS-PR8Pre-Amplifier (30MHz - 8GHz)1/25/2018Annual1/25/2019102333ATM180-442A-KF20dB Nominal Gain Horn Antenna3/13/2018Annual3/13/2019T058601-02Rohde & Schwarz HL562EUltra Broadband Antenna (30MHz - 6GHz)6/8/2018Annual6/8/2019100810Rohde & Schwarz TC-TA18Cross Polarized Vivaldi Antenna (400MHz-18GHz)11/13/2017Annual11/13/2018101057Rohde & Schwarz TC-TA18Cross Polarized Vivaldi Antenna (400MHz-18GHz)11/29/2017Annual11/29/2018101063Rohde & Schwarz HFH2-Z2 Loop Antenna 3/13/2018Annual 3/13/2019100519 7.0 T E S T R E S U L T S Summary 7.1 Company Name:
Apple Inc. FCC ID:
BCG-A1977 FCC Classification:
Digital Transmission System (DTS) Number of Channels:
75 FCC Part Section(s) RSS Section(s) Test Description Test Limit Test Test Condition Result Reference 15.247(a)(2) RSS-247 [5.2]
6dB Bandwidth
> 500kHz PASS Section 7.2 15.247(b)(3) RSS-247 [5.4(4)]
Transmitter Output Power 1 Watt PASS Section 7.3 15.247(e) RSS-247 [5.2]
Transmitter Power Spectral Density 8dBm / 3kHz Band PASS Section 7.4 CONDUCTED 15.247(d) RSS-247 [5.5]
Band Edge /
Out-of-Band Emissions 20dBc PASS Sections 7.5, 7.6 15.205 15.209 RSS-Gen [8.9]
General Field Strength Limits (Restricted Bands and Radiated Emission Limits) Emissions in restricted bands must meet the radiated limits detailed in 15.209 (RSS-Gen [8.9]) RADIATED PASS Sections 7.7, 7.8, 7.9 15.207 RSS-Gen [8.8]
AC Conducted Emissions 150kHz 30MHz
< FCC 15.207 limits
(RSS-Gen[8.8]) LINE CONDUCTED PASS Section 7.10 Table 7-1. Summary of Test Results Notes:
1. All modes of operation were investigated. The test results shown in the following sections represent the worst case emissions. 2. The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. 3. All antenna port conducted emissions testing was performed on a test bench with the antenna port of the EUT connected to the spectrum analyzer through calibrated cables and attenuators. 4. For radiated band edge, automated test software was used to measure emissions and capture the corresponding plots necessary to show compliance. The measurement software utilized is PCTEST Chamber Automation, Version 0.2.15. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 12 of 64 6dB Bandwidth Measurement Bluetooth (HDR) 7.2 15.247(a.2); RSS-247 [5.2]
Test Overview and Limit The bandwidth at 6dB down from the highest in-band spectral density is measured with a spectrum analyzer connected to the transmitter antenna terminal of the EUT while the EUT is operating at maximum power and at the appropriate frequencies. All modes of operation were investigated and the worst case configuration results are reported in this section. The minimum permissible 6dB bandwidth is 500 kHz. Test Procedure Used ANSI C63.10-2013 Section 11.8.2 Option 2 KDB 558074 D01 v05 Section 8.2 Test Settings 1. The signal analyzers automatic bandwidth measurement capability of the spectrum analyzer was used to perform the 6dB bandwidth measurement. The X dB bandwidth parameter was set to X = 6. The bandwidth measurement was not influenced by any intermediate power nulls in the fundamental emission. 2. RBW = 100kHz 3. VBW 3 x RBW 4. Detector = Peak 5. Trace mode = max hold 6. Sweep = auto couple 7. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Test Notes None FCC ID: BCG-A1977 Figure 7-1. Test Instrument & Measurement Setup MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 13 of 64 Table 7-2. Conducted Bandwidth Measurements Plot 7-1. 6dB Bandwidth Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 1) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 14 of 64 24044.0ePA1HDR42162.0500Pass24414.0ePA38HDR42160.0500Pass24784.0ePA75HDR42161.0500Pass24048.0ePA1HDR84164.0500Pass24418.0ePA38HDR84165.0500Pass24788.0ePA75HDR84164.0500PassPower SchemeChannel No.Bluetooth ModeMeasured Bandwidth [kHz]Minimum Bandwidth [kHz]Frequency [MHz]Data Rate [Mbps]Pass / Fail Plot 7-2. 6dB Bandwidth Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 38) Plot 7-3. 6dB Bandwidth Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 15 of 64 Plot 7-4. 6dB Bandwidth Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 1) Plot 7-5. 6dB Bandwidth Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 38) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 16 of 64 Plot 7-6. 6dB Bandwidth Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 17 of 64 7.3 Output Power Measurement Bluetooth (HDR) 15.247(b.3); RSS-247 [5.4(4)]
Test Overview and Limits The transmitter antenna terminal of the EUT is connected to the input of a spectrum analyzer. Measurements are made while the EUT is operating at maximum power and at the appropriate frequencies. The maximum permissible conducted output power is 1 Watt. Test Procedure Used ANSI C63.10-2013 Section 11.9.1.3 ANSI C63.10-2013 Section 11.9.2.3.2 KDB 558074 D01 v05 Section 8.3.1.3 Test Settings Method PKPM1 (Peak Power Measurement) The maximum peak conducted output power may be measured using a broadband peak RF power meter. The power meter shall have a video bandwidth that is greater than or equal to the DTS bandwidth and shall utilize a fast-responding diode detector. Method AVGPM-G (Average Power Measurement) Average power measurements were performed only when the EUT was transmitting at its maximum power control level using a broadband power meter with a pulse sensor. The power meter implemented triggering and gating capabilities which were set up such that power measurements were recorded only during the ON time of the transmitter. The trace was averaged over 100 traces to obtain the final measured average power. Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-2. Test Instrument & Measurement Setup for Peak and Average Power Measurement Test Notes None FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 18 of 64 Peak Output Power Measurement - Bluetooth (HDR) 7.3.1 15.247(b.3), RSS-247 [5.4(d)]
Table 7-3. Peak Conducted Output Power Measurements (Bluetooth (HDR) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 19 of 64
[dBm][mW]24044.0ePA1HDR415.6937.06824414.0ePA38HDR415.4735.23724784.0ePA75HDR415.4234.83424044.0iPA1HDR413.6823.33524414.0iPA38HDR413.4622.18224784.0iPA75HDR413.4622.18224048.0ePA1HDR815.6336.55924418.0ePA38HDR815.4034.67424788.0ePA75HDR815.3834.51424048.0iPA1HDR813.6323.06724418.0iPA38HDR813.4121.92824788.0iPA75HDR813.4021.878Frequency [MHz]Data Rate [Mbps]Power SchemeChannel No.Bluetooth ModePeak Conducted Power 7.3.2 15.247(b.3), RSS-247 [5.4(d)]
Average Output Power Measurement - Bluetooth (HDR) Table 7-4. Average Conducted Output Power Measurements (Bluetooth (HDR) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 20 of 64
[dBm][mW]24044.0ePA1HDR413.0019.95324414.0ePA38HDR412.8419.23124784.0ePA75HDR412.9419.67924044.0iPA1HDR411.0012.58924414.0iPA38HDR410.8212.07824784.0iPA75HDR410.9612.47424048.0ePA1HDR813.0019.95324418.0ePA38HDR812.8019.05524788.0ePA75HDR812.9319.63424048.0iPA1HDR811.0012.58924418.0iPA38HDR810.8012.02324788.0iPA75HDR810.9312.388Average Conducted PowerFrequency [MHz]Data Rate [Mbps]Power SchemeChannel No.Bluetooth Mode Power Spectral Density Bluetooth (HDR) 7.4 15.247(e); RSS-247 [5.2]
Test Overview and Limit The peak power density is measured with a spectrum analyzer connected to the antenna terminal of the EUT while the EUT is operating at maximum power and at the appropriate frequencies. The maximum permissible power spectral density is 8 dBm in any 3 kHz band. Test Procedure Used ANSI C63.10-2013 Section 11.10.2 Method PKPSD KDB 558074 D01 v05 Section 8.4 Test Settings 1. Analyzer was set to the center frequency of the DTS channel under investigation 2. Span = 1.5 times the DTS channel bandwidth 3. RBW = 3kHz 4. VBW = 1MHz 5. Detector = peak 6. Sweep time = auto couple 7. Trace mode = max hold 8. Trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-3. Test Instrument & Measurement Setup Test Notes None FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 21 of 64 Table 7-5. Conducted Power Density Measurements FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 22 of 64 24044.0ePA1HDR4-4.7358.0-12.7424414.0ePA39HDR4-4.6228.0-12.6224784.0ePA75HDR4-4.3498.0-12.3524044.0iPA1HDR4-4.7368.0-12.7424414.0iPA39HDR4-4.6338.0-12.6324784.0iPA75HDR4-4.3518.0-12.3524048.0ePA1HDR8-5.1058.0-13.1124418.0ePA39HDR8-5.0158.0-13.0224788.0ePA75HDR8-4.7238.0-12.7224048.0iPA1HDR8-5.1178.0-13.1224418.0iPA39HDR8-5.0078.0-13.0124788.0iPA75HDR8-4.7458.0-12.75Frequency [MHz]Data Rate [Mbps]Power SchemeChannel No.Bluetooth ModeMeasured Power Spectral Density [dBm]Maximum Permissible Power Density [dBm / 3kHz]Margin [dB]
Plot 7-7. Power Spectral Density Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 1) Plot 7-8. Power Spectral Density Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 38) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 23 of 64 Plot 7-9. Power Spectral Density Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 75) Plot 7-10. Power Spectral Density Plot (Bluetooth (HDR), 4Mbps, iPA Ch. 1) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 24 of 64 Plot 7-11. Power Spectral Density Plot (Bluetooth (HDR), 4Mbps, iPA Ch. 38) Plot 7-12. Power Spectral Density Plot (Bluetooth (HDR), 4Mbps, iPA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 25 of 64 Plot 7-13. Power Spectral Density Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 1) Plot 7-14. Power Spectral Density Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 38) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 26 of 64 Plot 7-15. Power Spectral Density Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 75) Plot 7-16. Power Spectral Density Plot (Bluetooth (HDR), 8Mbps, iPA Ch. 1) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 27 of 64 Plot 7-17. Power Spectral Density Plot (Bluetooth (HDR), 8Mbps, iPA Ch. 38) Plot 7-18. Power Spectral Density Plot (Bluetooth (HDR), 8Mbps, iPA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 28 of 64 Conducted Emissions at the Band Edge 7.5 15.247(d); RSS-247 [5.5]
Test Overview and Limit For the following out of band conducted spurious emissions plots at the band edge, the EUT was set to transmit at maximum power with the largest packet size available. These settings produced the worst-case emissions. The limit for out-of-band spurious emissions at the band edge is 30dB below the fundamental emission level, as determined from the in-band power measurement of the DTS channel performed in a 100kHz bandwidth. Test Procedure Used ANSI C63.10-2013 Section 11.11.3 KDB 558074 D01 v05 Section 8.7.2 Test Settings 1. Start and stop frequency were set such that the band edge would be placed in the center of the plot 2. Span was set large enough so as to capture all out of band emissions near the band edge 3. RBW = 100kHz 4. VBW = 300kHz 5. Detector = Peak 6. Number of sweep points 2 x Span/RBW 7. Trace mode = max hold 8. Sweep time = auto couple 9. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Test Notes None FCC ID: BCG-A1977 Figure 7-4. Test Instrument & Measurement Setup MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 29 of 64 Plot 7-19. Band Edge Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 1) Plot 7-20. Band Edge Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 30 of 64 Plot 7-21. Band Edge Plot (Bluetooth (HDR), 4Mbps, iPA Ch. 1) Plot 7-22. Band Edge Plot (Bluetooth (HDR), 4Mbps, iPA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 31 of 64 Plot 7-23. Band Edge Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 1) Plot 7-24. Band Edge Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 32 of 64 Plot 7-25. Band Edge Plot (Bluetooth (HDR), 8Mbps, iPA Ch. 1) Plot 7-26. Band Edge Plot (Bluetooth (HDR), 8Mbps, iPA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 33 of 64 Conducted Spurious Emissions 7.6 15.247(d); RSS-247 [5.5]
Test Overview and Limit For the following out of band conducted spurious emissions plots, the EUT was set to transmit at maximum power with the largest packet size available. The worst case spurious emissions were found in this configuration. The limit for out-of-band spurious emissions at the band edge is 30dB below the fundamental emission level, as determined from the in-band power measurement of the DTS channel performed in a 100kHz bandwidth per the procedure in Section 11.1 of KDB 558074 D01 v05 and Section 11.11.3 of ANSI C63.10-
2013. Test Procedure Used ANSI C63.10-2013 Section 11.11.3 KDB 558074 D01 v05 Section 8.5 Test Settings 1. Start frequency was set to 30MHz and stop frequency was set to 25GHz (separated into two plots per channel) 2. RBW = 1MHz 3. VBW = 3MHz 4. Detector = Peak 5. Trace mode = max hold 6. Sweep time = auto couple 7. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-5. Test Instrument & Measurement Setup FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 34 of 64 Test Notes 1. RBW was set to 1MHz rather than 100kHz in order to increase the measurement speed. 2. The display line shown in the following plots denotes the limit at 30dB below the fundamental emission level measured in a 100kHz bandwidth. However, since the traces in the following plots are measured with a 1MHz RBW, the display line may not necessarily appear to be 30dB below the level of the fundamental in a 1MHz bandwidth. 3. For plots showing conducted spurious emissions near the limit, the frequencies were investigated with a reduced RBW to ensure that no emissions were present. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 35 of 64 Plot 7-27. Conducted Spurious Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 1) Plot 7-28. Conducted Spurious Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 1) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 36 of 64 Plot 7-29. Conducted Spurious Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 38) Plot 7-30. Conducted Spurious Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 38) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 37 of 64 Plot 7-31. Conducted Spurious Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 75) Plot 7-32. Conducted Spurious Plot (Bluetooth (HDR), 4Mbps, ePA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 38 of 64 Plot 7-33. Conducted Spurious Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 1) Plot 7-34. Conducted Spurious Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 1) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 39 of 64 Plot 7-35. Conducted Spurious Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 38) Plot 7-36. Conducted Spurious Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 38) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 40 of 64 Plot 7-37. Conducted Spurious Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 75) Plot 7-38. Conducted Spurious Plot (Bluetooth (HDR), 8Mbps, ePA Ch. 75) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 41 of 64 Radiated Spurious Emission Measurements 7.7 15.205 15.209 15.247(d); RSS-Gen [8.9]
Test Overview and Limit All out of band radiated spurious emissions are measured with a spectrum analyzer connected to a receive antenna while the EUT is operating at maximum power and at the appropriate frequencies. Only the radiated emissions of the configuration that produced the worst case emissions are reported in this section. All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47 CFR and Table 6 of RSS-Gen (8.10) must not exceed the limits shown in Table 7-6 per Section 15.209 and RSS-
Gen (8.9). Field Strength Measured Distance
[V/m]
2400/F (kHz) 24000/F (kHz) 30 100 150 200 500
[Meters]
300 30 30 3 3 3 3 Table 7-6. Radiated Limits Frequency 0.009 0.490 MHz 0.490 1.705 MHz 1.705 30.00 MHz 30.00 88.00 MHz 88.00 216.0 MHz 216.0 960.0 MHz Above 960.0 MHz Test Procedures Used ANSI C63.10-2013 Section 6.6.4.3 KDB 558074 D01 v05 Section 8.6, 8.7 Test Settings Average Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW = 3kHz > 1/T 4. Averaging type was set to RMS to ensure that video filtering was applied in the power domain 5. Detector = peak 6. Sweep time = auto 7. Trace mode = max hold 8. Trace was allowed to run for at least 50 times (1/duty cycle) traces FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 42 of 64 Peak Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW is set depending on measurement frequency, as specified in Table 7-7 below 3. VBW = 3MHz 4. Detector = peak 5. Sweep time = auto couple 6. Trace mode = max hold 7. Trace was allowed to stabilize Frequency 9 150kHz 0.15 30MHz 30 1000MHz
> 1000MHz RBW 200 300Hz 9 10kHz 100 120kHz 1MHz Table 7-7. RBW as a Function of Frequency Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-6. Radiated Test Setup >1GHz FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 43 of 64 Test Notes 1. The optional test procedures for antenna port conducted measurements of unwanted emissions per the guidance of KDB 558074 D01 v05 were not used to evaluate this device for compliance to radiated limits. All radiated spurious emissions levels were measured in a radiated test setup. 2. All emissions lying in restricted bands specified in 15.205 and Section 8.10 of RSS-Gen are below the limit shown in Table 7-6. 3. The antenna is manipulated through typical positions, polarity and length during the tests. The EUT is manipulated through three orthogonal planes. 4. This unit was tested with its standard battery. 5. The spectrum is measured from 9kHz to the 10th harmonic of the fundamental frequency of the transmitter using CISPR quasi peak detector below 1GHz. Above 1 GHz, average and peak measurements were taken using linearly polarized horn antennas. The worst-case emissions are reported however emissions whose levels were not within 20dB of the respective limits were not reported. 6. Average measurements were recorded using a VBW of 3kHz, per Section 4.1.4.2.3 of ANSI C63.10-
2013, since 1/T is equal to just under 3kHz. This method was used because the EUT could not be configured to operate with a duty cycle > 98%. Both average and peak measurements were made using a peak detector. 7. Emissions below 18GHz were measured at a 3 meter test distance while emissions above 18GHz were measured at a 1 meter test distance with the application of a distance correction factor. 8. No significant radiated band edge emissions were found in the 2310 2390MHz restricted band. 9. The "-" shown in the following RSE tables are used to denote a noise floor measurement. Sample Calculations Determining Spurious Emissions Levels o Field Strength Level [dBV/m] = Analyzer Level [dBm] + 107 + AFCL [dB/m]
o AFCL [dB/m] = Antenna Factor [dB/m] + Cable Loss [dB]
o Margin [dB] = Field Strength Level [dBV/m] Limit [dBV/m]
Radiated Band Edge Measurement Offset o The amplitude offset shown in the radiated restricted band edge plots in Section 7.8 was calculated using the formula:
Offset (dB) = (Antenna Factor + Cable Loss + Attenuator) Preamplifier Gain FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 44 of 64 Radiated Spurious Emission Measurements 15.205 15.209 15.247(d); RSS-Gen [8.9]
Plot 7-39. Radiated Spurious Plot above 1GHz (4Mbps, ePA Ch.1, Ant. Pol. H & V) Plot 7-40. Radiated Spurious Plot above 1GHz (4Mbps, ePA Ch.38, Ant. Pol. H & V) Plot 7-41. Radiated Spurious Plot above 1GHz (4Mbps, ePA Ch.75, Ant. Pol. H & V) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 45 of 64 Plot 7-42. Radiated Spurious Plot above 1GHz (8Mbps, ePA Ch.1, Ant. Pol. H & V) Plot 7-43. Radiated Spurious Plot above 1GHz (8Mbps, ePA Ch.38, Ant. Pol. H & V) Plot 7-44. Radiated Spurious Plot above 1GHz (8Mbps, ePA Ch.75, Ant. Pol. H & V) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 46 of 64 Radiated Spurious Emission Measurements (Above 18GHz) 15.209 Plot 7-45. Radiated Spurious Plot above 1GHz (8Mbps, ePA, Ant. Pol. H) Plot 7-46. Radiated Spurious Plot above 1GHz (8Mbps, ePA, Ant. Pol. V) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 47 of 64 Radiated Spurious Emission Measurements 15.205 15.209 15.247(d); RSS-Gen [8.9]
Bluetooth Mode:
Power Scheme:
Distance of Measurements:
Operating Frequency:
Channel:
HDR4 ePA 3 Meters 2404MHz 1 Table 7-8. Radiated Measurements @ 3 meters Bluetooth Mode:
Power Scheme:
Distance of Measurements:
Operating Frequency:
Channel:
HDR4 ePA 3 Meters 2441MHz 38 Table 7-9. Radiated Measurements @ 3 meters FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 48 of 64 4808.00AvgV---79.816.8134.0053.98-19.984808.00PeakV---67.416.8146.4073.98-27.5812020.00AvgV---82.7517.9842.2353.98-11.7512020.00PeakV---71.2117.9853.7773.98-20.21AFCL [dB/m]Field Strength [dBV/m]Limit [dBV/m]Margin [dB]Turntable Azimuth [degree]Analyzer Level [dBm]Frequency [MHz]DetectorAnt. Pol. [H/V]Antenna Height [cm]4882.00AvgV---79.686.8134.1353.98-19.854882.00PeakV---67.766.8146.0573.98-27.937323.00AvgV---80.9111.1237.2153.98-16.777323.00PeakV---69.2411.1248.8873.98-25.1012205.00AvgV---82.8718.4042.5353.98-11.4512205.00PeakV---71.0418.4054.3673.98-19.62Field Strength [dBV/m]Limit [dBV/m]Margin [dB]Analyzer Level [dBm]AFCL [dB/m]Frequency [MHz]DetectorAnt. Pol. [H/V]Antenna Height [cm]Turntable Azimuth [degree]
Radiated Spurious Emission Measurements 15.205 15.209 15.247(d); RSS-Gen [8.9]
Bluetooth Mode:
Power Scheme:
Distance of Measurements:
Operating Frequency:
Channel:
HDR4 ePA 3 Meters 2478MHz 75 Table 7-10. Radiated Measurements @ 3 meters Bluetooth Mode:
Power Scheme:
Distance of Measurements:
Operating Frequency:
Channel:
HDR8 ePA 3 Meters 2404MHz 1 Table 7-11. Radiated Measurements @ 3 meters FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 49 of 64 4956.00AvgV---79.977.4634.4953.98-19.494956.00PeakV---68.287.4646.1873.98-27.807434.00AvgV---81.3611.4737.1153.98-16.867434.00PeakV---69.6611.4748.8173.98-25.1612390.00AvgV---82.5617.9942.4353.98-11.5512390.00PeakV---71.1217.9953.8773.98-20.11Limit [dBV/m]Margin [dB]Analyzer Level [dBm]AFCL [dB/m]Field Strength [dBV/m]Frequency [MHz]DetectorAnt. Pol. [H/V]Antenna Height [cm]Turntable Azimuth [degree]4808.00AvgV---79.756.8134.0653.98-19.924808.00PeakV---67.486.8146.3373.98-27.6512020.00AvgV---82.7517.9842.2653.98-11.7212020.00PeakV---71.7217.9853.2673.98-20.72Frequency [MHz]DetectorAnt. Pol. [H/V]Antenna Height [cm]Field Strength [dBV/m]Limit [dBV/m]Margin [dB]Turntable Azimuth [degree]Analyzer Level [dBm]AFCL [dB/m]
Radiated Spurious Emission Measurements 15.205 15.209 15.247(d); RSS-Gen [8.9]
Bluetooth Mode:
Power Scheme:
Distance of Measurements:
Operating Frequency:
Channel:
HDR8 ePA 3 Meters 2441MHz 38 Table 7-12. Radiated Measurements @ 3 meters Bluetooth Mode:
Power Scheme:
Distance of Measurements:
Operating Frequency:
Channel:
HDR8 ePA 3 Meters 2478MHz 75 Table 7-13. Radiated Measurements @ 3 meters FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 50 of 64 4882.00AvgV---79.776.8134.0453.98-19.944882.00PeakV---68.306.8145.5173.98-28.477323.00AvgV---81.0011.1237.1253.98-16.867323.00PeakV---69.2411.1248.8873.98-25.1012205.00AvgV---82.9318.4042.4753.98-11.5112205.00PeakV---71.7318.4053.6773.98-20.31Frequency [MHz]DetectorAnt. Pol. [H/V]Antenna Height [cm]Turntable Azimuth [degree]Limit [dBV/m]Margin [dB]Analyzer Level [dBm]AFCL [dB/m]Field Strength [dBV/m]4956.00AvgV---79.837.4634.6353.98-19.354956.00PeakV---67.697.4646.7773.98-27.217434.00AvgV---81.3511.4737.1253.98-16.857434.00PeakV---69.3611.4749.1173.98-24.8612390.00AvgV---82.3317.9942.6653.98-11.3212390.00PeakV---71.1617.9953.8373.98-20.15Frequency [MHz]DetectorAnt. Pol. [H/V]Antenna Height [cm]Turntable Azimuth [degree]Limit [dBV/m]Margin [dB]Analyzer Level [dBm]AFCL [dB/m]Field Strength [dBV/m]
Radiated Restricted Band Edge Measurements 7.8 15.205 15.209; RSS-Gen [8.9]
The radiated restricted band edge measurements are measured with an EMI test receiver connected to the receive antenna while the EUT is transmitting. The amplitude offset shown in the following plots for average measurements was calculated using the formula:
Offset (dB) = (Antenna Factor + Cable Loss + Attenuator) Preamplifier Gain Bluetooth Mode:
Power Scheme:
HDR4 ePA Measurement Distance:
3 Meters Operating Frequency:
2404MHz Channel:
1 Plot 7-47. Radiated Restricted Lower Band Edge Measurement (Average & Peak) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 51 of 64 Radiated Restricted Band Edge Measurements 15.205 15.209; RSS-Gen [8.9]
The amplitude offset shown in the following plots for average measurements was calculated using the formula:
Offset (dB) = (Antenna Factor + Cable Loss + Attenuator) Preamplifier Gain Bluetooth Mode:
Power Scheme:
HDR8 ePA Measurement Distance:
3 Meters Operating Frequency:
2404MHz Channel:
1 Plot 7-48. Radiated Restricted Lower Band Edge Measurement (Average & Peak) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 52 of 64 Radiated Restricted Band Edge Measurements 15.205 15.209; RSS-Gen [8.9]
The amplitude offset shown in the following plots for average measurements was calculated using the formula:
Offset (dB) = (Antenna Factor + Cable Loss + Attenuator) Preamplifier Gain Bluetooth Mode:
Power Scheme:
HDR4 ePA Measurement Distance:
3 Meters Operating Frequency:
2478MHz Channel:
75 Plot 7-49. Radiated Restricted Upper Band Edge Measurement (Average & Peak) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 53 of 64 Radiated Restricted Band Edge Measurements 15.205 15.209; RSS-Gen [8.9]
The amplitude offset shown in the following plots for average measurements was calculated using the formula:
Offset (dB) = (Antenna Factor + Cable Loss + Attenuator) Preamplifier Gain Bluetooth Mode:
Power Scheme:
HDR8 ePA Measurement Distance:
3 Meters Operating Frequency:
2478MHz Channel:
75 Plot 7-50. Radiated Restricted Upper Band Edge Measurement (Average & Peak) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 54 of 64 Radiated Spurious Emissions Measurements Below 1GHz 7.9 15.209; RSS-Gen [8.9]
Test Overview and Limit All out of band radiated spurious emissions are measured with a spectrum analyzer connected to a receive antenna while the EUT is operating at its maximum duty cycle, at maximum power, and at the appropriate frequencies. All data rates and modes were investigated for radiated spurious emissions. Only the radiated emissions of the configuration that produced the worst case emissions are reported in this section. All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47 CFR must not exceed the limits shown in Table 7-14 per Section 15.209. Field Strength Measured Distance
[V/m]
2400/F (kHz) 24000/F (kHz) 30 100 150 200 500
[Meters]
300 30 30 3 3 3 3 Table 7-14. Radiated Limits Frequency 0.009 0.490 MHz 0.490 1.705 MHz 1.705 30.00 MHz 30.00 88.00 MHz 88.00 216.0 MHz 216.0 960.0 MHz Above 960.0 MHz Test Procedures Used ANSI C63.10-2013 Test Settings Quasi-Peak Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 120kHz (for emissions from 30MHz 1GHz) 3. Detector = quasi-peak 4. Sweep time = auto couple 5. Trace mode = max hold 6. Trace was allowed to stabilize FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 55 of 64 Test Setup The EUT and measurement equipment were set up as shown in the diagrams below. Figure 7-7. Radiated Test Setup < 30Mhz Figure 7-8. Radiated Test Setup < 1GHz FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 56 of 64 Test Notes 1. All emissions lying in restricted bands specified in 15.205 are below the limit shown in Table 7-14. 2. The broadband receive antenna is manipulated through vertical and horizontal polarizations during the tests. The EUT is manipulated through three orthogonal planes. 3. This unit was tested with its standard battery. 4. The spectrum is investigated using a peak detector and final measurements are recorded using CISPR quasi peak detector. The worst-case emissions are reported however emissions whose levels were not within 20dB of the respective limits were not reported. 5. Emissions were measured at a 3 meter test distance. 6. Emissions are investigated while operating on the center channel of the mode, band, and modulation that produced the worst case results during the transmitter spurious emissions testing. 7. No spurious emissions were detected within 20dB of the limit below 30MHz. 8. The results recorded using the broadband antenna is known to correlate with the results obtained by using a tuned dipole with an acceptable degree of accuracy. The VSWR for the measurement antenna was found to be less than 2:1. 9. The wide spectrum spurious emissions plots shown on the following pages are used only for the purpose of emission identification. There were no emissions detected in the 30MHz 1GHz frequency range, as shown in the subsequent plots. 10. The unit was tested with all possible mode and power schemes and only the highest emission is reported. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 57 of 64 Plot 7-51. Radiated Spurious Plot below 1GHz (4Mbps, ePA, Pol. H & V, with WCP + AC/DC Adapter attached) Table 7-15. Radiated Spurious Emissions Below 1GHz (4Mbps, ePA, with WCP + AC/DC Adapter attached) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 58 of 64 0 10 20 30 40 50 60 70 8030M 5060 80100M200300400500 8001GLevel in dBV/mFrequency in HzPreview Result 1V-PK+Preview Result 1H-PK+Critical_Freqs PK+FCC Part 15C 30MHz-1GHzFCC Part 15C 30MHz-1GHz_-6Final_Result QPKFCC Part 15C 30MHz-1GHzFCC Part 15C 30MHz-1GHz_-631.36Quasi-PeakV - --63.22-15.4428.3440.00-11.6647.95Quasi-PeakV - --63.89-25.4017.7140.00-22.29112.31Quasi-PeakH - --67.97-23.0615.9743.52-27.55177.54Quasi-PeakH - --67.09-23.2516.6643.52-26.86273.91Quasi-PeakH - --62.47-22.6221.9146.02-24.11877.64Quasi-PeakH - --76.20-11.6419.1646.02-26.86Analyzer Level [dBm]AFCL [dB/m]Field Strength [dBV/m]Limit [dBV/m]Margin [dB]Frequency [MHz]DetectorAnt. Pol. [H/V]Antenna Height [cm]Turntable Azimuth [degree]
Plot 7-52. Radiated Spurious Plot below 1GHz (8Mbps, ePA, Pol. H & V, with WCP + AC/DC Adapter attached) Table 7-16. Radiated Spurious Emissions Below 1GHz (8Mbps, ePA, with WCP + AC/DC Adapter attached) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 59 of 64 0 10 20 30 40 50 60 70 8030M 5060 80100M200300400500 8001GLevel in dBV/mFrequency in HzPreview Result 1V-PK+Preview Result 1H-PK+Critical_Freqs PK+FCC Part 15C 30MHz-1GHzFCC Part 15C 30MHz-1GHz_-6Final_Result QPKFCC Part 15C 30MHz-1GHzFCC Part 15C 30MHz-1GHz_-631.36Quasi-PeakV - --62.71-15.4428.8540.00-11.1542.08Quasi-PeakV - --66.22-21.5019.2840.00-20.7277.34Quasi-PeakV - --66.89-23.9116.2040.00-23.80176.23Quasi-PeakH - --68.70-22.2916.0143.52-27.51278.81Quasi-PeakH - --62.10-22.4722.4346.02-23.59899.61Quasi-PeakH - --77.03-11.2818.6946.02-27.33Analyzer Level [dBm]AFCL [dB/m]Field Strength [dBV/m]Limit [dBV/m]Margin [dB]Frequency [MHz]DetectorAnt. Pol. [H/V]Antenna Height [cm]Turntable Azimuth [degree]
7.10 Line-Conducted Test Data 15.207; RSS-Gen [8.8]
Test Overview and Limit All AC line conducted spurious emissions are measured with a receiver connected to a grounded LISN while the EUT is operating at its maximum duty cycle, at maximum power, and at the appropriate frequencies. All data rates and modes were investigated for conducted spurious emissions. Only the conducted emissions of the configuration that produced the worst case emissions are reported in this section. All conducted emissions must not exceed the limits shown in the table below, per Section 15.207 and RSS-Gen (8.8). Frequency of emission Conducted Limit (dBV)
(MHz) 0.15 0.5 0.5 5 5 30 Quasi-peak 66 to 56*
56 60 Average 56 to 46*
46 50 Table 7-17. Conducted Limits
*Decreases with the logarithm of the frequency. Test Procedures Used ANSI C63.10-2013, Section 6.2 Test Settings Quasi-Peak Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the spurious emission of interest 2. RBW = 9kHz (for emissions from 150kHz 30MHz) 3. Detector = quasi-peak 4. Sweep time = auto couple 5. Trace mode = max hold 6. Trace was allowed to stabilize Average Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the spurious emission of interest 2. RBW = 9kHz (for emissions from 150kHz 30MHz) 3. Detector = RMS 4. Sweep time = auto couple 5. Trace mode = max hold 6. Trace was allowed to stabilize FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 60 of 64 Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-9. Test Instrument & Measurement Setup Test Notes 1. 2. 3. 4. All modes of operation were investigated and the worst-case emissions are reported using mid channel. The emissions found were not affected by the choice of channel used during testing. The limit for an intentional radiator from 150kHz to 30MHz are specified in Part 15.207 and RSS-Gen (8.8). Corr. (dB) = Cable loss (dB) + LISN insertion factor (dB) QP/AV Level (dBV) = QP/AV Analyzer/Receiver Level (dBV) + Corr. (dB) 5. Margin (dB) = QP/AV Limit (dBV) - QP/AV Level (dBV) 6. 7. Traces shown in plot are made using a peak detector. Deviations to the Specifications: None. FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 61 of 64 Plot 7-53. Line Conducted Plot with Bluetooth HDR (L1, with WCP + Laptop attached) Table 7-18. Line Conducted Measurements with Bluetooth HDR (L1, with WCP + Laptop attached) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 62 of 64 0 10 20 30 40 50 60 70 80150k 300400500 8001M2M3M4M5M6 810M20M30MLevel in dBVFrequency in HzPreview Result 2-AVGPreview Result 1-QPKCritical_Freqs AVGCritical_Freqs QPKFCC Part 15 Class B Voltage on Mains QPFCC Part 15 Class B Voltage on Mains AVFinal_Result QPKFinal_Result AVGFCC Part 15 Class B Voltage on Mains QPFCC Part 15 Class B Voltage on Mains AV Plot 7-54. Line Conducted Plot with Bluetooth HDR (N, with WCP + Laptop attached) Table 7-19. Line Conducted Measurements with Bluetooth HDR (N, with WCP + Laptop attached) FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 63 of 64 0 10 20 30 40 50 60 70 80150k 300400500 8001M2M3M4M5M6 810M20M30MLevel in dBVFrequency in HzPreview Result 2-AVGPreview Result 1-QPKCritical_Freqs AVGCritical_Freqs QPKFCC Part 15 Class B Voltage on Mains QPFCC Part 15 Class B Voltage on Mains AVFinal_Result QPKFinal_Result AVGFCC Part 15 Class B Voltage on Mains QPFCC Part 15 Class B Voltage on Mains AV 8.0 C O N C L U S I O N data relate collected The the Apple Watch FCC ID: BCG-A1977 is in compliance with Part 15 Subpart C (15.247) of the FCC Rules and RSS-247 of the Innovation, Science and Economic Development Canada Rules. item(s) tested show only and that the FCC ID: BCG-A1977 MEASUREMENT REPORT
(CERTIFICATION) Approved by:
Quality Manager Test Report S/N:
1C1806040005-03.BCG 2018 PCTEST Engineering Laboratory, Inc. V 8.1 05/10/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM. Test Dates:
5/15 - 8/18/2018 EUT Type:
Watch Page 64 of 64
This product uses the FCC Data API but is not endorsed or certified by the FCC