FCC ID: WBQCS9016 RGB RF remote

70.00 mm RF Wireless Remote Functions RGB LED Controller CS9016 Instructions 19 Dynamic Modes Card Type Remote 20 Static Colors Ultra Slim Design Very Smooth Effects Demo Mode Speed Adjustable Easy Remote Pairing Brightness Adjustable Direct Color Select 1 2 3 4 5 MODE

SPEED

DEMO SPEED

COLOR

MODE

BRIGHT

COLOR

BRIGHT

RF Wireless 9 11 10 8 7 6 1.Turn on/Standby Press this key to turn on unit or switch to standby mode. Unit will turn on and restore to previous status at powering on moment. 2/9.Dynamic Modes Adjust Switch to dynamic mode from static color mode, or switch between dynamic modes. 7/8.Brightness Adjust Adjust static color brightness. Press Bright+ to increase brightness and press Bright- to decrease. Unit will switch to static color mode lf press this key at dynamic mode. 11.Demo Mode Press this key will switch to Demo mode. At demo mode, it will loop play 9 dynamic modes, each mode repeat 3 times. 3/10.Dynamic Seed Adjust Adjust dynamic playing speed. Press Speed+ to increase speed and press Speed- to decrease speed. Unit will switch to dynamic mode lf press this key at static color mode. lnstalling 4/5.Static Color Adjust Switch to static color mode from dynamic mode, or switch between different static colors. 6.Direct Color Select Shortcut key to static colors. When press the specific color key.LED will play the same static color. The direct colors are included inCOLOR+andCOLOR-operation. 1.Power Supply This unit accepts DC 5V to 24V power supply . The inner pole polarity is positive and sleeve is negative . Please select proper power supply according to the LED application. 2.LED Output This unit support common anode connection LED products. The mark peak output current is 4A per channel, please reduce load if main unit is overheating. indicates the common connection node. The CAUTION !Do not short circuit the LED output ,this may lead to permanent damage!

LED CONTROLLER With RF Remote Control Peak Output Current

:3*4A 2 Common Node 1 3.Remote Controller Please pull out the insulate part before using . The RF wireless remote signal can pass through barrier , so its not necessary to aim at the main unit when operate . For proper receiving remote signal , do not install the main unit in closed metal parts. The remote battery is 3V CR2025 type , please only replace with same type battery. Specification Dynamic Mode Static Color PWM Grade Brightness Grade Speed Grade Demo mode Working Voltage 19 modes 20 colors 256 levels 5 levels 10 levels Yes DC 5~24V Output Current 3-way, peak 4A per channel Remote Frepuency 433.92MHz Remote Distance

15m at open area FCC Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Radiation Exposure Statement This device complies with RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

8 LJ ire) i=]

10 20 30 4 U1 NTT TTA TET] PTTTY LYE OL OZ O OF OS 09 OZ 08 06 09 o4 o8 06 00lor oz o oF eee arene

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: 2020/11/21 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID WBQCS9016 For the product stated above, we request that the following information be held confidential;

Model name CS9016 Exhibits Long-Term Confidentiality Short-Term Short-Term Confidentiality Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos Users Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name:

Robert L. Fils Company: AQUATIC AV Address:

Phone:

Fax:

E-Mail:

282 Kinney Drive, San Jose, CA 95112, United States 408-559-1668 408-559-0125 bobf@fasinductries.com

AQUATIC AV 282 Kinney Drive, San Jose, CA 95112, United States Tel: 408-559-1668 Fax: 408-559-0125 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

11/21/2020 We, AQUATIC AV the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID:WBQCS9016 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name:

Robert L. Fils Company: AQUATIC AV Address:

Phone:

Fax:

E-Mail:

282 Kinney Drive, San Jose, CA 95112, United States 408-559-1668 408-559-0125 bobf@fasinductries.com