Thank you for selecting this BLUETOOTH headset. This BLUETOOTH headset uses 2.4GHz Bluetooth technology to provide lightweight, handsfree, private and secure communication without the inconvenience of wires. This Bluetooth headset is compatible with devices that support the Bluetooth Headset and Handsfree profiles. To be able to use the headset with a mobile phone, the phone needs to have built-in Bluetooth technology, or a compatible Bluetooth phone adaptor. KEY DIAGRAM 1. Function Button 2. Volume + Button 3. Volume Button 4. Microphone 5. Earhook 6. EarGel 7. Speaker 8. Earhook hole GETTING START To use your headset, please follow these simple steps :
I. II. III. I. NOTE : The battery pack for your headset is already installed when you purchase your headset. The battery is not fully charged when you buy the headset. Before you can use the headset, you need to charge the headsets self-contained battery for up to 2-3 hours. To charge the headset, please follow this guide :
Connect the included AC charger to the main power supply and then to the headset charger port. While charging, the red indicator light is on and remains on until charging is complete. When charging is complete, the Red light will go out, you can then remove the charger from the headset. Charge your headset battery Switch your headset on. Pair your headset with a Bluetooth Telephone Charge the battery SWITCHING YOUR HEADSET ON/OFF LOW BATTERY WARNING When the headset is on and the battery becomes low, the RED LIGHT will flash to remind you the headset needs to be recharged. Recharge the battery as described above. II. To turn your headset on, press & hold Function button & Volume button simultaneous For 2 seconds. The GREEN LED light will quick flash three times, and goes to stand-by mode. The indicator light will flash green every 2-3 seconds whilst the headset is on. To turn your headset off, press & hold Function button & Volume button simultaneous for 2 seconds, The RED LED light will then flash 3 times & goes to OFF mode. III. Prior to using your headset for the first time, you MUST pair it with another BLUETOOTH device, such as a mobile telephone. The Bluetooth connection between the headset and your phone can be established by setting up a paired link. With a paired link, the phone remembers the headsets ID, and these 2 items are then paired together eliminating the need to repeat the set up process with future use. Only paired devices can utilize Auto-Answer and Auto-Transfer functions. The information below describes pairing instructions for a typical device. For specific instructions, refer to your mobile telephone user guide. PAIRING PROCEDURE. PAIRING YOUR HEADSET 1. Switch off your headset & turned on your cell phone, place the headset and telephone where they are easily viewable. Make sure the Bluetooth feature of your telephone is turn on. 2. On your headset (under off mode), Press & hold FUNCTION button & volume button simultaneous for 5 seconds. (The Green LED light will flash 3 times after 2 seconds, then 3 seconds later, The Red LED light will flash), then release the Function button & Volume button, and wait about 2 seconds, Afterwards the Green LED will turn on and RED LED light will flash. Your headset is now entering into pairing mode & will remain discoverable by other BLUETOOTH devices for 60 seconds. 3. On your cell phone, search for devices by selecting DISCOVER from the Bluetooth options menu. Check your mobile telephone display and follow the instruction. 4. Select BH220 on the menu of you phone, Enter the passkey 1234, when your phone menu prompts you, and the phone will start to pair the headset with the phone (the device ID is now stored in the phones memory). 5. Your phone screen will advise that pairing has been successful, and headset indicator light will then goes to stand-by (GREEN LED light flash) mode. 6. Once the headset and phone have successfully paired you are ready to place and receive calls. GETTING THE PERFECT FIT This Bluetooth headset is designed to fit comfortably in your ear. For added comfort, you can add the optional Eargel and/or Earhook SELECT LEFT OR RIGHT EAR The headset is able for wearing on your both ears by changing the direction of Earhook. Simply unplug the Earhook from the headset, plug earhook again in the different direction for left or right ear fitting selection. PLACING THE HEADSET ON YOUR EAR In order to wear the headset, please follow these instructions 1. Put the earhook in its open position (90% away from the headset) 2. Loop the earhook behind your ear. 3. Close the headset towards your ear USING YOUR HEADSET ANSWERING A CALL To answer a call, wait for the headset to ring, just press the Function button to answer the call. When the call is coming, Both RED LED & GREEN LED will flash alternately to alert the user. REJECT A CALL To reject a call, wait for the headset to ring, keep hold Function button for 2 seconds to reject a call. ENDING A CALL To end a call, hold function button till the call is terminated at any time during a call TRANSFERING A CALL TO THE HEADSET If you are using your telephone handset, you can transfer the call to your headset by pressing the Function button. This function is subject to your mobile phone supports call transferring function. MUTE FEATURE The mute feature, when activated, allowed you to hear the person you are calling, but they cannot hear you. To mute a call, pressing volume + & volume button simultaneous during a call. To de-activate mute, press volume + & volume button together again. LAST NUMBER REDIAL When making a call, you can dial the last number called using your headset. Press Volume +
or Volume button under stand-by mode to redial the last number. VOICE DIALING Making sure that your mobile phone supports voice dialing function., and voice tags are stored. Pressing Function button under stand-by mode, you will hear a short beep tone., and then speak the voice tag name. A tone prompts you say the name of the person you wish to call. The phone automatically dials your selection. ADJUSTING THE VOLUME To increase the volume level, press & release the Volume + button. To decrease the volume level, press & release the Volume button. When the maximum or minimum volume level is reached, the headset sound short beep tones. The volume only can be adjusted during talking. DISCONNECTING YOUR HEADSET & MOBILE PHONE To terminate the connection between the headset and your mobile phone, press Function button for 2 seconds. To active the connection between the headset & your mobile phone, press Function again for 2 seconds. FCC Notice to Users / Product Statements This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. SAFETY AND GENERAL INFORMATION Electro Magnetic Interference / Compatibility Note : Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. Aircrafts & Hospitals Please switch OFF the headset before boarding any aircraft to prevent interference with the aircraft communications systems. Also please switch OFF the headset in any facility where posted notices instruct you to do so. Hospitals and Healthcare facilities may be using equipment that is sensitive to EMI. PLEASE NOTE:
"The driver is ultimately responsible for the safe operation and control of their vehicle at all times. You should never use a hand held phone, including sending or reading text or picture messages, while driving . Research indicates that there is a risk to safety when the driver of a motor vehicle is distracted and using a mobile phone while driving can be a distraction. Vodafone strongly recommends that you use a hands free solution when driving and, if you are in any doubt, that you find a safe place to pull over and stop before making or taking a call."
Federal Communications Commission (FCC) Statement The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.