die cut line folding line Overview FUNCTION button 3. Wearing the headset Turn the earbud to an angle of approximately 30 degrees from the direction of the headset depending on which side of the body you wish to wear the headset. 30 right VOLUME DOWN button VOLUME UP button Your package contains:
a headset with a medium-sized earbud tted an AC adapter 2 spare earbuds - 1 large and 1 small. headset left 30 supplied earbud spare earbuds
(1 small and 1 large) Once the earbud is in position, insert the headset into your ear canal according to the pictures below. AC adapter mini USB plug Specications Weight: 10.5 grams Size: 27 mm x 50 mm x 10.5 mm Talk time: up to 5.5 hours Standby time: up to 170 hours Bluetooth version: 2.0 Microphone: directional Getting started 1. Charging the headset for the rst time The headset must be fully charged before you use it for the rst time. Connect the mini USB plug from the AC adapter to the headset and plug the AC adapter into the electrical socket and charge the headset for 8 hours. A red light will come on while the headset is charging. If it fails to come on, press the FUNCTION button to activate it. The red light will go o once the headset is fully charged. After the inital charge, recharging takes approximately 3 hours. 2. Choosing the earbud The earbud attached to the headset is medium-
sized. Large and small earbuds are also included. Choose the size that works best for you. 3 earbuds supplied
(small, medium and large) 30 30 left right 30 30 4. Turning the headset on To turn the headset on, press the FUNCTION button until you see the blue light long ashes once time and you hear 4 tones. 5. Pairing For the headset to function, it must rst be paired
(linked) with a Bluetooth-enabled device like a mobile phone. To do this, the headset must be turned on. Press and hold down the FUNCTION button until blue light long ashes once time. Keep pressing the FUNCTION button until there are alternate rapid red and blue ashing lights. Then release the FUNCTION button. Use your Bluetooth-enabled devices menu (see relevant user manual) to search for the headset and select the M11 once it nds it. When the device requests a passkey, enter 0000 (four zeros) and then press YES or OK. Your device is now paired to the headset for future use. 6. Turning the headset o To turn the headset o, hold the FUNCTION button down until you see the red light long ashes once time. 7. Answering / Ending / Rejecting a call To answer an incoming call, press the FUNCTION button. To end a call, press the FUNCTION button again. To reject an incoming call, hold the FUNCTION button down for 2 seconds. 8. Adjusting the volume Use the VOLUME UP button to increase the volume and the VOLUME DOWN button to decrease the volume. (See Overview.) 9. Low battery warning A warning tone will sound if the battery is low , and the ashing blue light will change to a red light, with 1 ashes every 10 seconds. Summary of headset light sequences Headset status Headset indicator light Power on Power o Pairing mode Blue light long ashes once Red light long ashes once Blue and red light alternating ashes Pairing successful Blue light ashes once Stand-by mode, During call Incoming call Low battery Battery charging Blue light ashes once every 10 seconds Blue light rapid ashes until the call is received Red light ashes once every 10 seconds Red light is on continuously Charging completed Red light goes o 10. Voice dialing If your Bluetooth-enabled device supports voice dialing, you can make a voice dialing call by rst pressing the FUNCTION button. Once prompted, proceed as you would normally with the voice dialing on your mobile phone. To cancel voice dialing, press the FUNCTION button. 11. Transferring calls between the headset and your mobile phone A call can be transferred from your mobile phone to the headset and vice versa. To transfer a call from the headset to the mobile phone, press the FUNCTION button twice. To transfer a call from the mobile phone to the headset, press the FUNCTION button once. 12. Redial last number To redial the last number called, press the FUNCTION button twice. A beeping sound will be heard, and the last number called will be redialed. To cancel , press the FUNCTION button once. 13. Three-way calling To receive a waiting call and hold an active call, press and hold down the FUNCTION button for approximately 2 seconds. To alternate between the active call and the waiting call, press and hold the FUNCTION button for approximately 2 seconds. To use the three-way calling function, press and hold the FUNCTION button for approximately 10 seconds. To end the waiting call, press and hold the VOLUME DOWN button for approximately 2 seconds. To end the active call, press the FUNCTION button twice. Note: Use of some of these functions depends on the type of mobile phone. Check which functions are available in the relevant mobile phone user manual. during charging. The battery is already fully charged. it to the AC adapter and leave the headset to charge for 8 hours. it to the AC adapter and leave the headset to charge for 8 hours. and then back on again. Then turn the headset o and turn it on again to re-establish the connection. from the headset and the headset should be ready to use. The headset has been left unused for too long causing the battery to completely discharge. it to the AC adapter and leave the headset to charge for 8 hours. The headset has been left unused for too long causing the battery to completely discharge. Troubleshooting & FAQ Problem: You cannot turn the headset on. Cause:
This may be due to a malfunction with the battery. Solution: Reactivate the headset by connecting Cause:
Solution: Reactivate the headset by connecting Problem: The red light does not come on Cause:
Solution: Disconnect the mini USB plug Cause:
Solution: Reactivate the headset by connecting Problem: The headset is connected to the Bluetooth-enabled device, but doesnt work properly. Cause:
This may be due to a connection failure between the device and the headset. Solution: Reset the device by turning it o Problem: You cannot hear the ringtone for Cause:
Solution: Change the phone settings to enable Problem: There is static noise during Cause:
Solution: For optimum sound quality, wear the headset on the same side of your body as the mobile phone. Problem: The headset has been unexpectedly disconnected, or you cannot answer calls using the headset. It is a normal feature of the headset Cause:
to go into low-energy mode after 90 minutes of inactivity. Many Bluetooth-enabled devices support this mode, however, if your mobile phone does not support this, the headset will disconnect from the device. Solution: Press the FUNCTION button once to conversations. The headset uses radio frequency waves at the lowest transmission power levels possible in order that minimum battery power is used, at the same time as meeting the signal eciency standards for Bluetooth Class 2. The distance between the headset and device should be kept to a minimum wherever possible. an incoming call. This can happen if the phone is set to silent mode or if the ringtone has been disabled. reconnect and answer the call. It may, however, take an extra 2-3 seconds to make the connection. the incoming call ringtone. function, or the control buttons dont work as expected. This may be due to improper usage or it is likely that the headset has been stored at too high temperature which can cause the processor chip to malfunction. Problem: The headset incorrectly performs a Cause:
Solution: The headset should be reset. Press and Care and maintenance The headset has been designed and produced using the latest technology, and should be looked after carefully. The following recommendations will help you to use the headset in accordance with the requirements of the warranty, and will help to extend its lifetime. hold down the VOLUME UP, VOLUME DOWN and FUNCTION buttons simultaneously for approximately 10 seconds. The red light will ashes 1 time to indicate a headset shutdown and reset. Then press the FUNCTION button once more to restart the headset for normal use. Avoid storing the headset in humid, dusty or moist conditions, or at temperatures over 45C. These conditions may cause the electronic components to degrade. Avoid storing the headset in very cold conditions (below -10C). When the headset is turned on at these temperatures, condensa-
tion is created inside the headset and may damage the electronic circuits. Avoid using the headset in very hot conditions, as the heat may shorten the lifespan of the electronic equipment and may also damage the battery. Avoid knocking or shaking the headset. Careless usage may damage the internal circuits. Do not clean the headset with strong chemicals or substances, as they may damage its surface. Do not attempt to open the headset. The battery is not user-replaceable and replacing it will invalidate the warranty. These recommendations will help to extend the lifetime of your headset. If you have any problems with the headset, please refer to the warranty section of this guide. Certication and safety approvals FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. CE This product is CE marked according to provisions of the R&TTE Directive. Bluetooth The Bluetooth trademark and logos are owned by Bluetooth SIG, Inc. and any use of such trademarks by Argard are under license. Warranty Argard Co., Ltd, the producer of this Bluetooth headset, guarantees to provide quality after-sales support and service to buyers or users of this product, under the following conditions:
1. The product warranty is valid for a period of one (1) year from the date of purchase. 2. The buyer must produce a receipt or other documentation showing the date, time and place where the product was purchased. 3. The buyer is not covered by this warranty under the following conditions. The product has been damaged due to improper usage or storage, falling or being dropped hard on the ground, or coming into direct contact with steam or water. The product has been repaired or modied by an unauthorized person. The product has been sent for repairs after the warranty has expired, in which case the company will charge for the service at the normal cost. The battery has been modied, or an unsuitable battery has been used. Charging equipment other than that provided with the headset has been used. 4. If a problem occurs during the warranty period, the buyer should send or take the product to the original vendor. All information regarding this warranty or the product may be modied without notice. Use only the supplied adaptor. Meaning of WEEE symbol e.g. this symbol indicating separate collection electrical and electronic equipment. Modication not expressly approved by this company could void the user's authority to operate the equipment. www.argard.com