FCC ID: 2APLE18300418 Cellular and Battery Backup

Arlo Security Hub User Manual Protect and Connect. Table of Contents 1.0 Security Hub Onboarding Guide 2.0 Sensor Onboarding Guide 2.1 Sensor Onboarding Guide - Door 2.2 Sensor Onboarding Guide - Window 2.3 Sensor Onboarding Guide - Garage 2.4 Sensor Onboarding Guide - Motion 2.5 Sensor Onboarding Guide - Water Leak 3.0 Backup Battery Onboarding Guide 4.0 Federal Communication Commission Interference Statement RF Exposure Statements:

Industry Canada Statement:

5.0 E-Label Process 3 7 10 11 12 13 15 16 17 17 17 18 Protect and Connect. 1.0 Security Hub Onboarding Guide 1 2 3 4 Step 1 On the bottom of the Security Hub, locate and scan the QR code. Step 2 Wait until only the check button LED flashes before selecting Continue. Step 3 Press and hold the check button until all LED button lights flash. Troubleshooting From Step 4 If the Security Hub is unable to join the network. Factory reset by simutaneously pressing the check and x button on the Keypad until all LED button lights flash quickly. Continue the setup from Step 1 again. 3 5 Protect and Connect. 1.0 Security Hub Onboarding Guide Contd Troubleshooting From Step 7 If the Security Hub does not connect to the selected Wi-Fi network, check the status of your Wi-Fi network and select Try Again. If the problem persists, select Need Help?. 6 7 Step 6 In the type field, enter the password of the selected Wi-Fi network. Step 8 Name and ensure the location of the Security Hub is correct. Step 9 If updates are available, Security Hub will be directed to Step 10 and 11. 8 9 10 11 Step 11 The Security Hub has the latest firmware, and setup can be continued. 4 Protect and Connect. 1.0 Security Hub Onboarding Guide Contd Troubleshooting From Step 10 If the Security Hub is unable to update the firmware, ensure the Security Hub is plugged in properly and select Try Again. 12 13 Step 12 Create a memorable Security PIN and enter it into the type field. Step 13 After PIN is correctly re-entered, give your Security PIN a name. Step 14 S Arm Away by pressing the Arm Away button. Select Continue to Troubleshooting From Step 12 Verify that the Security PIN entered matches the first Security PIN that was entered. Set the Security PIN again from Step 12 if the problem persists. Step 15 Set Arm Home by pressing the Arm Home button and entering the Security 14 15 5 Protect and Connect. 1.0 Security Hub Onboarding Guide Contd Troubleshooting From Step 15 If the Security PIN entered is incorrect. Repeat the Step 15 again ensuring the correct Security PIN is entered. 16 17 Step 16 Set Disarm by pressing the Disarm button and entering the Security PIN. Step 17 Activate Panic by pressing and holding the Panic button. To exit Panic mode press the Disarm button, enter the Security PIN, and press the check button. Troubleshooting From Step 17 If the Security PIN entered is incorrect. Repeat the Step 17 again ensuring the correct Security PIN is entered. Step 18 If previous Arlo Devices are part of your Security System, they will appear below. New devices can be setup by selecting Add Another Device. 18 19 6 Protect and Connect. 2.0 Sensor Onboarding Guide Troubleshooting From Step 2 If the Security Hub is offline, check the status of your Wi-Fi network and ensure the hub is plugged in correctly. 1 2 Step 1 If an Security Hub is not connected, follow the instructions from 1.0 to onboard the Security Hub. Step 2 Select the All-In-One Sensor and have your Sensor ready. Troubleshooting From Step 3 If the Security Hub has not previously been set to disarm. Select the Disarm button and wait until completed. 7 3 Protect and Connect. 2.0 Sensor Onboarding Guide Contd 4 5 6 7 Step 4 Select one of the following: Open/Close Detection (2.1-2.3), Motion Detection

(2.4), or Water Leak Detection (2.5) Step 5 Following the arrows in the side of the Sensor, slide off the front cover Troubleshooting From Step 8 If the blue LED does not flash on the Sensor, select The LED isnt flashing blue. Press the sync button on the bottom of the Sensor, then process Continue to proceed. 8 Step 8 Wait until the blue LED flashes on the front of the Sensor, then press Continue to proceed. 9 8 Protect and Connect. 2.0 Sensor Onboarding Guide Contd Troubleshooting From Step 9 If the Security Hub is unable to find the Sensor, select either Try Again or Need Help? and select the sync button on the bottom of the sensor. 10 Step 10 If done correctly, the Sensor has been found by the Security Hub and the following screen will display. 11 12 13 14 Step 13 Select one of the following: Door (2.1), Window (2.2), or Garage (2.3) Step 14 Within your Arlo Security Hub package, have the Magnet and blue adhesive ready. 9 Protect and Connect. 2.1 Sensor Onboarding Guide - Door 1 2 3 Step 1 Ensure both the Sensor and Magnet are vertical and aligned inch or 12 mm between one another. Step 3 With the Sensor and Magnet properly aligned, place onto a door frame. 4 5 6 Step 5 & 6 Open and Close the door to verify if the status is accurate. Select Continue if it is correct or Need help? if it is incorrect. 10 Protect and Connect. 2.2 Sensor Onboarding Guide - Window 1 2 3 4 Step 1 Ensure both the Sensor and Magnet are vertical and aligned inch or 12 mm between one another. Step 3 & 4 Place the Sensor (and Magnet) on the frame of a tilting window. 5 6 7 8 Step 7 & 8 Open and Close the window to verify if the status is accurate. Select Continue if it is correct or Need help? if it is incorrect. 11 Protect and Connect. 2.3 Sensor Onboarding Guide - Garage 1 2 3 4 Step 1 Ensure both the Sensor and Magnet are vertical and aligned inch or 12 mm between one another. Step 3 & 4 Place the Sensor (and Magnet) on the frame of a garage. 5 6 7 8 Step 7 & 8 Open and Close the window to verify if the status is accurate. Select Continue if it is correct or Need help? if it is incorrect. 12 Protect and Connect. 2.4 Sensor Onboarding Guide - Motion 1 2 3 4 Step 1 Find an location for the Sensor to be placed. Step 2-4 Obtain the adhesive (and Corner Mounting Plate) to install the Sensor. 5 6 7 8 Step 6 Press the sync button on the bottom of the Sensor, then select Continue to proceed. 13 Protect and Connect. 2.4 Sensor Onboarding Guide - Motion Contd Step 9 & 10 Wave your hand at the Sensor to verify if the status is accurate. Select Continue if it is correct. 9 10 14 Protect and Connect. 2.5 Sensor Onboarding Guide - Water Leak 1 2 3 Step 2 Determine a location for the Sensor to detect water leaks. Step 3 Press the sync button on the bottom of the Sensor. Step 4 & 5 The circle will appear green if the Sensor is within an acceptable range of the Security Hub. If the circle is red, move the Sensor closer to the Security Hub. 4 5 15 Protect and Connect. 3.0 Backup Battery Onboarding Guide 1 2 3 Step 1 Once the Backup Battery has been connected to the Security Hub, wait for the LTE backup to activate. Step 3 If done correctly, the Devices page will display both Wi-Fi and LTE strength. 16 Protect and Connect. 4.0 Federal Communication Commission Interference Statement Model Number: MS1001 & LBB1001 & SH1001 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. RF Exposure Statements:

This Transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. Industry Canada Statement:

This device complies with Industry Canada license-exempt RSSs . Operation is subject to the following two conditions (Only for MS1001 & SH1001) :

1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux cownditions suivantes (Uniquement pour MS1001 & SH1001) :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. 17 Protect and Connect. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration dexposition aux radiations:

Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. 18 Protect and Connect. 5.0 E-Label Process The MS1001 (Arlo Sensor connects to a companion device, SH1001 (Arlo Hub) via the Arlo App running on any Android phone and/or iPhone. The Sensors FCC ID can be retrieved from these steps:

1 2 3 Step 1:

Launch the Arlo App. From the Devices Screen, tap the Settings icon next to the Sensor. Step 2:

Select the right-side drop down menu for the Sensor for Device Info. Step 3:

Select Regulatory The Sensor operates as a client to the Hub in a client/master network such that the Sensor can not initiate a transmission without receives an enabling signal from the Hub. The Hub recognizes the Sensor services and its FCC ID to present to the Arlo App running on the mobile phone. The Sensor must connect to the Hub by Arlo App to access the FCC ID and the operation can not rely on or require any other non-local server to operate. 4 19

The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2APLE18300418 IC: 23815-18300418 CAN ICES-003(B)/NMB-003(B) Model: LBB1001 Made in Vietnam S N I M E I XXXXXXXXXXXXX XXXXXXXXXXXXX 272-50108-01

Arlo Technologies Inc 2200 Faraday Avenue, Suite 150, Carlsbad, CA 92008, USA Date: 2022/05/19 FCC ID: 2APLE18300418 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize Underwriters Laboratories Taiwan Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Underwriters Laboratories Taiwan Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing Underwriters Laboratories Taiwan Co., Ltd. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) c) d) e) f) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

Make claims regarding certification only in respect of the scope for which certification has been granted;

Do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

Upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

Use certification only to indicate the products are certified as being in conformity with specified standards;

DocuSign Envelope ID: 0FF94641-9BAE-4B91-834B-EAB8BDB24746 g) h) i) j) Endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) Document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Name/Title: Douglas Leong / VP of Quality & Compliance Company Name: Arlo Technologies Inc Address: 2200 Faraday Avenue, Suite 150, Carlsbad, CA 92008, USA Tel: 4088903900 Fax: 4089078167 Email: compliance@arlo.com DocuSign Envelope ID: 0FF94641-9BAE-4B91-834B-EAB8BDB24746

Arlo Technologies Inc 2200 Faraday Avenue, Suite 150, Carlsbad, CA 92008, USA Date: Jul. 1, 2022 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 Subject: Request for Confidentiality FCC ID : 2APLE18300418 To whom it may concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Permanent Confidentiality Schematics Diagrams Block Diagram Operation Description BOM Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. v1.0 DocuSign Envelope ID: 335B0E3E-4A62-42AA-A7F8-E055356FB749 Short Term Confidentiality In addition to the above mentioned documents, pursuant to Public Notice DA 04-1705 of the commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we are requests that the commission to grant short-term confidentiality request on the following attachments for 180day. External Photo Internal Photo Test Setup Photo User Manual It is our understanding that measurement test reports and FCC ID label format cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Name/Title: Douglas Leong / VP of Quality & Compliance Company Name: Arlo Technologies Inc Address: 2200 Faraday Avenue, Suite 150, Carlsbad, CA 92008, USA Tel: 4089078000 Fax: 4089078167 Email: compliance@arlo.com v1.0 DocuSign Envelope ID: 335B0E3E-4A62-42AA-A7F8-E055356FB749