USER GUIDE Video Bridge 405 Version Date 1.0 1.1 1.2 04/05/2013 04/11/2013 05/10/13 Description Initial version Revised installation procedures Revised pairing procedures 2013 Pace plc. All rights reserved. Pace and the Pace logo are registered trademarks of Pace plc. All other trademarks are the property of their respective owners. Pace provides no warranty with regard to this manual, the software, or other information contained herein, and hereby expressly disclaims any implied warranties of merchantability or fitness for any particular purpose with regard to this manual, the software, or such other information, in no event shall Pace be liable for any incidental, consequential, or special damages, whether based on tort, contract, or otherwise, arising out of or in connection with this manual, the software, or other information contained herein or the use thereof. 05162013 5100-001270-000 Contents Chapter 1 Introduction. 4 Chapter 2 Setting up the video bridge. 6 Connection overview . 6 Setting up the video bridge. 7 Connecting the video bridge to the gateway . 7 Connecting power. 8 Connecting devices to the access point. 9 Connecting a wireless set-top box . 9 Connecting a station. 11 Connecting other devices. 12 Locating the SSID and wireless network key . 13 Chapter 3 Troubleshooting . 14 Appendix A Regulatory information. 16 Contents 3 Introduction 1 The Pace video bridge is a wireless access point that can be used to connect set-top boxes or other devices to an existing gateway using a 5 GHz wireless connection. The video bridge uses 802.11n 5 GHz high performance wireless technology to provide a high bandwidth connection for video streams and other demanding applications. POWER ETHERNET WIRELESS AP WPS 405 Pace wireless technology practically eliminates wireless cold spots in the home. Increased power and sensitivity, along with optimized antenna design, give better range and performance than typical 802.11n wireless access points. 4 Chapter 1 Introduction Status lights Use the status lights on the front of the video bridge to determine its current state. Status light Description Power Ethernet Wireless Solid green. The video bridge is on. Red. The video bridge may have a fault with its power supply. Check the power adapter and its connections. Disconnect and reconnect the power adapter. Solid green. A device is connected to the Ethernet port. Flickering green. There is activity from the device connected to the Ethernet port. The flickering of the light is synchronized to data traffic. Solid green. A set-top box or other device is connected to the video bridge using a wireless connection. Flickering green. There is inbound or outbound activity. The flickering of the light is synchronized to data traffic. Wireless signal strength AP WPS Shows the strength of the wireless connection between the video bridge and wireless devices. If more than one device is connected, the indicator shows the strength of the device with the weakest signal. Solid green. The video bridge is in access point mode. Flickering green. There is activity from a connected device. The flickering of the light is synchronized to data traffic. Flashing green. WPS (Wi-Fi Protected Setup) is configuring the video bridge. Chapter 1 Introduction 5 Setting up the video bridge 2 Connect the 405 video bridge to your existing gateway, then connect devices to the video bridge using the 5 GHz wireless connection. Note: We recommend that you use the included stand to install the video bridge vertically. This prevents things from being stacked on top of it, which can block vents and cause the device to overheat. Connection overview Connect the video bridge to the gateway using a wired connection, then connect devices to the video bridge using a wireless connection. The following illustration shows an overview of possible connections. Gateway Video bridge
(access point) Wireless connection Wireless set-top box Client devices WPS WPS Phone outlet 4 3 2 1 D N A B D A O R B T E N R E H T E L S D R E W O P T E S E R ETHERNET RESET POWER Video bridge
(client) ETHERNET RESET POWER Computer or other device 6 Chapter 2 Setting up the video bridge Setting up the video bridge Connect the video bridge to your existing gateway. The gateway should be online before you start this procedure. The video bridge will serve as a 5 GHz wireless access point. Connecting the video bridge to the gateway Use the Ethernet port to connect the video bridge to your existing gateway. 1. Connect one end of the yellow Ethernet cable to an available yellow Ethernet port on the gateway. 2. Connect the other end of the cable to the Ethernet port on the video bridge. Note: A 6-foot yellow Ethernet cable is provided with the video bridge. If you need another cable, use a Cat 5 or Cat 5e Ethernet cable. Gateway Video bridge
(access point) t e n r e h t E Chapter 2 Setting up the video bridge 7 Connecting power Use the power adapter that was packaged with the video bridge, because it matches the power requirements for the device. 1. Connect one end of the power adapter to the Power port on the video bridge. 2. Connect the other end to a power outlet. After the video bridge is powered on, the power light blinks green for a moment and then turns steady green. 8 Chapter 2 Setting up the video bridge Connecting devices to the access point After the video bridge is configured as an access point, you can start connecting devices to it using the 5 GHz wireless connection. You can connect one or more devices to the access point. Connecting a wireless set-top box You can use the access point to connect to a wireless set-top box. With a wireless set-
top box, you can watch television almost anywhere in your home. Place your television and set-top box just about anywhere, regardless of where existing TV outlets are located. 1. Connect the wireless set-top box to your television. See the television or set-top box documentation for more information. 2. Connect the power adapter for the wireless set-top box. The set-top box should start automatically. Follow the instructions on the screen. After a few minutes, you will see a message that the wireless set-top box is searching for a wireless access point. Chapter 2 Setting up the video bridge 9 3. Press the WPS button on the back of the wireless access point. The WPS light on the front of the access point will blink while the wireless set-top box connects to the wireless access point. WPS button WPS ETHERNET RESET POWER After the set-top box connects to the access point, you will see the following message on the television screen. If the set-top box does not connect to the access point after a few minutes, see Connection issues on page 14. To add a second wireless set-top box, repeat the steps in this procedure. 10 Chapter 2 Setting up the video bridge Connecting a station The video bridge can also be used as a client device. In this scenario, you would have two video bridges: the access point and the station. The access point is the video bridge that is connected to the gateway, and the station is the one connected to the set-top box. Gateway Video bridge
(access point) Video bridge
(station) TV WPS WPS Phone outlet 4 3 2 1 D N A B D A O R B T E N R E H T E L S D R E W O P T E S E R ETHERNET RESET POWER ETHERNET RESET POWER Set-top box 1. Ensure that the wireless access point is connected and turned on. See Setting up the video bridge on page 7. 2. Connect the station to the set-top box using the yellow Ethernet cable. Note: A 6-foot yellow Ethernet cable is provided with the video bridge. If you need another cable, use a Cat 5 or Cat 5e Ethernet cable. 3. Connect the power adapter for the station. See Connecting power on page 8. 4. Go to the wireless access point and press the WPS button on the back of the device. WPS button WPS ETHERNET RESET POWER Chapter 2 Setting up the video bridge 11 5. Return to the station and press the WPS button on the back of the device. The WPS lights on the front of the devices will blink while they search for each other (discovery mode). The wireless access point and the station will stay in discovery mode for up to two minutes while the devices try to establish a connection. If the station box does not connect to the wireless access point after a few minutes, try this procedure again. If the devices still do not connect, see Connection issues on page 14. Connecting other devices You can connect other wireless devicessuch as tablets, mobile phones, or notebooksto the access point if you need a 5 GHz connection. By default, the gateway is configured with a network name (SSID) and WPA-PSK/WPA2-PSK security. 1. On the wireless device, view the available wireless networks. The specifics of how you do this depend on the device you are connecting. The SSID (default wireless network name) and wireless network key are printed on the label on the side of the access point. 2. Select the appropriate wireless network name and connect. 3. At the prompt, enter the wireless network key. After the gateway recognizes the wireless device, the Wireless light turns steady green, and blinks when the wireless device starts transferring data with the gateway. 12 Chapter 2 Setting up the video bridge Locating the SSID and wireless network key The SSID (network name) and wireless network key are printed on the label on the side of the video bridge. SSID and wireless network key Chapter 2 Setting up the video bridge 13 Troubleshooting 3 This section provides information about common installation issues. If an issue has more than one potential cause, the most common cause is listed first. Power issues Use the information in this section to identify and resolve issues related to power. The Power light is not on The power cable may be loose or disconnected. Check the power cable to ensure that the cable is securely connected. If the power cable is plugged in to a power strip or switched outlet, ensure that it is on. Ensure that you are using the power supply that came with the video bridge. The power supply may be faulty. Verify that the light on the power supply is green. The AC outlet may be faulty. Try plugging the video bridge in to a known good outlet. The Power light blinks immediately after the device starts, and then turns steady green The Power light blinks during POST (Power on self-test). This is normal behavior. The Power light is red The POST (Power on self-test) may have failed. Press the Reset button and hold it for 10 seconds to reset the video bridge. Connection issues Use the information in this section to identify and resolve issues related to connectivity. The Ethernet light is not on The Ethernet cable may be loose or disconnected. Check the connections to ensure that the cable is securely connected. 14 Chapter 3 Troubleshooting A wireless set-top box or other device cannot connect to the access point Ensure that you have a strong enough signal. At least three green bars should appear on the signal strength indicator on the set-top box. Ensure that you have waited long enough for the set-top box to start and to connect. This can take up to ten minutes. If you see a red antenna on the television screen, restart the wireless set-top box and try to connect again. The Wireless light is not on No devices are currently connected to the video bridge over the wireless connection. Ensure that the wireless feature is enabled. For more information, go to the video bridge configuration page at http://192.168.1.200. A wireless device cannot get an IP address The device may not be set up with the appropriate security type or security key. Ensure that the wireless device is using the appropriate credentials. The wireless signal is weak The wireless device may be out of range. Ensure that the wireless device is within the range of the video bridge. Chapter 3 Troubleshooting 15 Regulatory information A Declaration of conformity The following sections describe regulatory compliance by region. FCC / Industry Canada Compliance This device has been tested and certified as compliant with the regulations and guidelines set forth in the Federal Communication commission - FCC part 15 and Industry Canada - ICES003 and RSS-210 Radio and telecommunication regulatory requirements. Le prsent materiel est conforme aux specifications techniques applicables d'Industrie Canada. Cet appareil numrique de la classe [*] est conforme la norme NMB-003 du Canada. Manufacturer: Pace Model(s): 405 Part 15 of FCC Rules / IC RSS-210 This device complies with part 15 of the FCC Rules and Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux normes CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause 16 Appendix A Regulatory information harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate this equipment. Failure to heed the Safety Information provided by failing to connect to a properly wired outlet may void the manufacturer's warranty. MPE/SAR/RF exposure information This device was verified for RF exposure and found to comply with Council Recommendation 1999/519/EC and FCC OET-65 RF exposure requirements. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. WARNING: While this device is in operation, a separation distance of at least 20 cm
(8 inches) must be maintained between the radiating antenna inside the EUT and the bodies of all persons exposed to the transmitter in order to meet the FCC RF exposure guidelines. Making changes to the antenna or the device is not permitted. Doing so may result in the installed system exceeding RF exposure requirements. This device must not be co-located or operated in conjunction with any other antenna or radio transmitter. ElectricalAC adapter This product is intended to be supplied with a listed Pace Direct Plug-In AC/DC Power adapter marked Class 2 or LPS and rated 12 V,1.5 A for all 405-xxx models. The AC/DC Power adapter supplied with this product is designed to ensure your personal safety and to be compatible with this equipment. Appendix A Regulatory information 17 Please follow these guidelines:
Do not use the adapter in a high moisture environment. Never touch the adapter when your hands or feet are wet. Allow adequate ventilation around the adapter. Avoid locations with restricted airflow. Connect the adapter to a proper power source. The voltage and grounding requirements are found on the product case and/or packaging. Do not use the adapter if the cord becomes damaged. Do not attempt to service the adapter. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture. Equipment LocationElectrical considerations CAUTION: Due to risk of electrical shock or damage, do not use this product near water, including a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Also, avoid using this product during electrical storms. Avoid locations near electrical appliances or other devices that cause excessive voltage fluctuations or emit electrical noise (for example, air conditioners, neon signs, high-
frequency or magnetic security devices, or electric motors). LocationEnvironmental considerations Do not plug the AC/DC power adapter into an outdoor outlet or operate the product outdoors. It is not waterproof or dustproof, and is for indoor use only. Any damage to the unit from exposure to rain or dust may void your warranty. Do not use the product where there is high heat, dust, humidity, moisture, or caustic chemicals or oils. Keep the gateway away from direct sunlight and anything that radiates heat, such as a stove or a motor. Repairs Do not, under any circumstances, attempt any service, adjustments, or repairs on this equipment. Instead, contact your local Pace Americas distributor or service provider for assistance. Failure to comply may void the product warranty. 18 Appendix A Regulatory information