FCC ID: 2AS8F-R1 Wireless Charger

Wireless Charger for Motorcycle User's manual R1/R2 Arzin Intelligent Co., Ltd www.motocam.net Please read this manual carefully before using the product Product description The Wireless Charger is a wireless charging product designed specifically for motorcycle brackets. Surface non-slip siticone material, 3M adhesive tape on the back, used with QC3.0 inteltigent step-down cable, put the phone on the surface, can achieve 10W wireless fast charge.Waterproof rating IP67 also can be used normally even in the rain. Installation instructions 1. Connect the red and black wires of the main Line of the charging cable to the positive and negative terminals of the ignition switch of the motorcycle. 2. After the main tine is connected to the ignition switch, operate the wiring in sequence to the handle bar and then fix it with cable ties. Reasonable wiring is required according to the actual situation of the vehicle because different types of vehicles differ in Line design. 3. Connect the USB receptacle Line with the waterproof connector of the main Une. The main line is connected to Waterproof connectors the ignition switch of the motorcycle 4. Remove the 3M adhesive tape on the back of the wireless chargee adjust the position according to different mobile phone holder and attach it to the surface of the mobile phone holder if it is a RAM holdec please remove the RAM adhesive tape first 5. When the device with wireless charging function conforms to the QI standard is placed at the center of the wireless chargei; charging will start automatical When the wireless charger is in normal working state, the LED white light is always on. Note: Keep the center position of the mobile phone atthe center of the the wireless charger when wirelessly charge. If it is networking properly please adjust the position of the phone until the phone shows normal power charging or the LED white light is always on.

(please Referto the figure below to place the position). When the status of the LED lightis blinking white, The wireless 6. charger is in the wrong and protection phase. At this point, you should pay attention to whether there is a metal object placed on the wireless charger. Remove it and observe if it can be used normally. If you still can't solve it, please contact the sales staff. QC3.0 Smart Power Cord Item Input Output Cable Length Parameters 12-24V 5V3A 2.5m How to charge the phone quickly?

1. First of all ensure that the mobile phone supports the fast charging function, the device will adaptivety output the corresponding charging power according to the mobile phone; if the mobile phone does not have a fast charging function, it can be charged normally. 2. When charging, make sure that the phone is in closely bonded to the round part of the bracket with the mark. 3. Please ensure that the thickness of the phone case is within 4mm, so that the wireless charging function can be used normally. 4. please check if the charging part of the bracket is aligned with the wireless charging part of the mobile phone, or if there is metal object between the wireless charging and the mobile phone holder. If the indicator Light flashes rapidly or goes out during charging, LED status description White LED Always on for 4s Status Self-testing Always on The device is charging the phone Flashes per 3s Flashes per Is The device is in the stand by state The power output is [ow, please adjust the position of the mobile phone in time Attention

* Do notdisassemble or modify it by yourself.

* Do not bring the product close tothe fire or into the fire.

* Do not use tine wireless charger under severe heat or corrosive conditions to avoid damage to tine circuit

* Do not place the magnetic card (ID card, bank card, etc.) with a magnetic strip or chip too closeto avoid the magnetic card failure. FCC WARNING STATEMENT Changes or modic ations not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit die rent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The distance between user and products should be no less than 20cm

FCC ID LABEL:

Label Location:

FCC ID: 2AS8F-R1 Product name: Wireless Charger Model No.: R1 Width:1cm This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Long:3cm

Date: Mar. 24, 2020 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen CTB Testing Technology Co., Ltd. Add: Floor 1&2, Building A, No. 26 of Xinhe Road, Xinqiao Community, Xinqiao Street, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Arzin Motocam Intelligent Co., Ltd Add: Room 222, Wan Yuan Business Building 2, Liuxian Road 2, Baoan District, Shenzhen China

<Signature>

Name: Abigail Luo Title: Business Manager Company: Arzin Motocam Intelligent Co., Ltd

Date: Mar. 24, 2020 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AS8F-R1 Product Name: Wireless Charger Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ) Schematics Block diagram Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors.

<Signature>

Name: Abigail Luo Title: Business Manager Company: Arzin Motocam Intelligent Co., Ltd

Model Difference Declaration To Whom It May Concern, We, Arzin Motocam Intelligent Co., Ltd Product: Wireless Charger Trademark: N/A Model Number: R1, R2, X1, X2 All models the function, software and electric circuit are the same, only with a product color, shape, nameplate and model named different. Test sample model: R1 Please contact me if you have any question. Name: Abigail Luo Date: Mar. 24, 2020 Title: Business Manager Signature of applicant: