A 128g
:
100mm 100mm 3 Vol +
2 Next song 1 Vol -
Play / pause Answer call Refuse call LED light / MIC 4 Previous song Forced pairing On / Off AUX in Micro USB HOW TO USE 1. General function Operation LED Status Power on Blue LED flashes 3 times Power off Red LED flashes 1 second Pairing Red LED & Blue LED flashes alternately Standby Blue LED flashes 1 times in 5 seconds Low battery Red LED flashes Charging Red LED keep lighting during charging Blue LED keep lighting when charging finished F10 User Manual 2. Basic Buttons Operation Power on: Push button to on side. Blue LED flashes 3 times. Headphone turn on. Power off: Push button to off side. Red LED turn off after flashes 1 times. Headphone turn off. Paring: After power on, the headphone will be entered into pairing mode automatically. Red LED & Blue LED flashes alternately. if not, long press 4
' Previous song' button for 3s to enter paring mode. 150mm 2 3 4 1 1 1 1 Volume adjust: Long press on buttons,one level voice volume changes. When volume reaches to Max or Minimum, "Di" reminding voice occurs. Play / Pause: Short press button, music pause. Press it again, music continues. Previous: In playback status, press button, music turns to previous one. Next: In playback status, press button, music turns to next one. Answer Call: Short press button to answer the phone call. End call: Short press button, phone call ended. Reject call: Long Press button for 2 seconds to reject a call. Battery Capacity status: When headphone connects to iOS devices, iOS devices show the headphone battery power status on the upper right corner. Charging: new headphone has enough power for pairing and dialing out for several times. When in low battery, please charging via USB cable for 3~4 hours. Red LED keep lighting during charging, blue LED keep lighting charging finished. Reset Mode: Connect the headphone to computer via Micro USB cable. When red LED light on, headphone reset finished. 3.5mm music line-in function: Connect Audio line in cable to 3.5 audio jack for wired music. Phone call function cannot be used in this mode. Headphone will be powered off after insert 3.5mm line-in cable. 3.5MM AUDIO JACK 1. Connect the 3.5 audio wire to the headphone and audio player. 2. You can adjust volume bottom of the audio player or the mobile phone to reach right volume to listen music. FEATURES 1. Bluetooth 5.0 2. 3.5mm music line-in function 3. iOS show the headphone battery power status SPECIFICATION Talk time: 20h Standby: 0.5mA Battery: 400mAh Standby time: 750h Charging time: 3~4h IC solution: QCC3005 Bluetooth: 5.0 Charging voltage: 5.0V Wireless range: 10m BT music play time: 20h Power voltage: 3.0~4.2V Speaker: 40mm 32 15%
Transmission power: CLASS 2 Transmission frequency: 2.4G Bluetooth: HSP / HFP / A2DP / AVRCP / SBC / AAC / APTX / PATXLL Sound pressure level (Sensitivity): 1083dB At 1kHz 1mw / IE KIT CONTENTS 1. Stereo Bluetooth headphone x 1 2. Charging Micro USB Cable x 1 3. User Manual x 1 4. 3.5mm audio wire x 1 WARNING 1. You must choose a qualified charger from a regular manufacturer to charge the headphone. 2. You must charge the headphone if it has not been used for more than 12 months. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.