Askey SFE3160S CBSD SFE3160S CBSD SmallCell Demonstration Quick Installation Guide Askey Computer Corporation March 1, 2020 1 Version 1.0 March 1, 2020 Askey SFE3160S CBSD Table of Contents 1. Whats Inside ................................................................................................................................................. 3 2. Getting to Know SFE3160S CBSD .................................................................................................................... 4 3. Quick Setup .................................................................................................................................................... 5 4. Common Troubleshooting Procedures ........................................................................................................... 6 2 Version 1.0 March 1, 2020 Askey SFE3160S CBSD 1. Whats Inside 2 X SFE3160S CBSD SmallCell 2 X SFE3160S POWER ADAPTOR 2 X ETHERNET CABLE 2 X ONE PLUS 7T CELL PHONE 1 X ONE PLUS 7T POWER ADAPTOR 1 X ASUS LTE ROUTER 1 X ASUS LTE ROUTER POWER ADAPTOR 3 Version 1.0 March 1, 2020 NOTICE: ASUS LTE ROUTER IS OPTIONAL FOR THE CBSD SMALLCELL DEMO SETUP. IT IS STRONGLY RECOMMEDNDED TO HAVE CONNECTION TO INTERNET VIA ETHERNET WHERE IPSEC PASSTHROUGH IS ENABLED, I.E. PORT 500, PORT 4500 ARE *NOT* BLOCKED BETWEEN SFE3160S CBSD SAMMCELL WAN PORT AND THE INTERNET. Askey SFE3160S CBSD NOTICE: GPS ANTENNA IS OPTIONAL IN THIS DEMONSTRATION WHERE GPS LOCATION HAS BEEN PRESET ON THE SMALLCELL FOR TESTING PURPOSE. 1 X GPS ANTENNA WITH LONG CABEL 2 X GPS ANTENNA 2. Getting to Know SFE3160S CBSD NOTICE: IT IS RECOMMENDED TO START TEST WITH SFE3160S UNIT A AS SHOWN IN THE ABOVE PICTURE. Grey LAN Port
(Connect to other devices if needed) Reset 1. Press and hold for 3 seconds for reboot 2. Press and hold for 20 seconds for factory setting reset and software update Yellow WAN Port
(Connect to Wi-Fi router or Wi-Fi cable modem router) Power
(Power on when AC Adaptor is plugged in) GPS Port
(Connect to GPS Antenna & Cable) 4 Version 1.0 March 1, 2020 Askey SFE3160S CBSD 3. Quick Setup 1) Connect your SFE3160S CBSD SmallCell to the Internet Connect the yellow Ethernet cable from the WAN yellow port on your SFE3160S to an available Ethernet port on your switch or cable modem. NOTICE: FOR THE CBSD SMALLCELL DEMO SETUP. IT IS REQUIRED TO HAVE CONNECTION TO INTERNET VIA ETHERNET WHERE IPSEC PASSTHROUGH IS ENABLED, I.E. PORT 500, PORT 4500 ARE *NOT* BLOCKED BETWEEN SFE3160S CBSD SAMMCELL WAN PORT AND THE INTERNET. NOTICE: GPS ANTENNA IS OPTIONAL IN THIS DEMONSTRATION WHERE GPS LOCATION HAS BEEN PRESET ON THE SMALLCELL FOR TESTING PURPOSE. 2) Power on your SFE3160S CBSD SmallCell Connect the power cable to the SFE3160S power port, then plug in your AC power adaptor into the power outlet. 3) Let your SFE3160S CBSD SmallCell setup After you power on your SFE3160S, the SFE360S will go through the setup process till LTE service is ready with the following LED state:
POWER (Solid Blue): Power on. Device self-testing and update complete. STATUS (Solid Blue): LTE service ready SERVICE (Solid Green): LTE service ready 5 Version 1.0 March 1, 2020 Askey SFE3160S CBSD 4. Common Troubleshooting Procedures Case State to Indicate Power LED Status LED LED Service Customer Care Description 1 Power On RED OFF OFF 1. If the device doesn't into this state after PLUN IN:
a. Please check the wall outlet is working fine. b. Please check whether the power cord of charger is connected or not. c. If the machine still can't into this state after the power cord and wall outlet are working properly. Hardware issue, please change the product. 2. If the device stays in this state more than 1 minute:
a. Hardware issue, please change the product. If the device stays in this state more than 1 minute, please check:
1. Please check the network cable is connected to the Ethernet port on your device, and the other end is connected to the network. 2. Please try to switch a different Ethernet cable. 3. Please check DHCP server is working normally. If the device stays in this state more than 5 minutes, please check:
1. Please check the IP address for this device can access the internet. 2. Please check the UDP port 500 and UDP port 4500 is opening at the firewall. If the device stays in this state more than 5 minutes, please check:
1. The location of device is allowed to cell up by SAS 2. The device can get the GPS signal (Take the GPS antenna to window / Stick to window if required) Please connect with administrator of HeMS to check whether the MME IP is correct or not. Please connect with administrator of HeMS to check whether the Cell ID, TAC, and PCI are correct or not. 2 Network is initializing GREEN OFF OFF 3 IPsec Tunnel is initializing BLUE RED FLASHING OFF LTE Service is initializing BLUE BLUE FLASHLING OFF Lost Connecting with MME Setting Error at HeMS LTE Service Ready LTE Service in Progress BLUE RED OFF BLUE OFF RED BLUE BLUE GREEN BLUE BLUE GRREEN FLASHING 4 5 6 7 8 6 Version 1.0 March 1, 2020 LTE Service in Maximum Capacity Over 9 10 Askey SFE3160S CBSD BLUE BLUE GREEN FLASHLING FLASHING LTE service is in Maximum Capacity. Now we support 128 UEs. Temperature FLASHING CHANGE CHANGE RED NO NO 11 RF Issue RED RED RED FLASHING FLASHING FLASHING 12 Software Update BLUE BLUE BLUE FLASHLING FLASHLING FLASHLING Your device is over-heating. Please move device to other area and try again. Hardware issue. Please restart the device. If the LED still in this state, please change the product. Software upgrade in progress, device will reboot automatically. 7 Version 1.0 March 1, 2020 Askey SFE3160S CBSD Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Connect the equipment into an outlet on a circuit different from that to which the receiver is Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. 8 Version 1.0 March 1, 2020