FCC ID: H8N-AP6275S WIFI+BT Combo Module

AP6275S User manual Product Name WIFI+BT Combo Module Brand Name ASKEY Model Name AP6275S Rating Voltage:

DC 3.3V 2.4GHz:

Frequency Range:

5GHz:

2.400 GHz ~ 2.4835 GHz (2.4GHz ISM Band) 5.15~5.35GHz, 5.47~5.725GHz, 5.725~5.85GHz

(5GHz UNII Band) 2.4GHz: Ch1 ~ Ch11 5.15~5.35 GHz: Ch36 ~ Ch64 5.47~5.725GHz: Ch100 ~ Ch142 5.725~5.85GHz: Ch149 ~ Ch165 Channels Antenna Type:

PIFA antenna Hardware version: V01 Software Version: Android 10 Product Features IEEE 802.11 Key Feature Lead Free design which is compliant with ROHS requirements. TX and RX low-density parity check (LDPC) support for improved range and power efficiency. Dual-stream spatial multiplexing up to 1200 Mbps data rate. 20, 40, 80 MHz channels with optional SGI (1024 QAM modulation) Real simultaneous dual-band Client MU-MIMO Supports standard SDIO v3.0, compatible with SDIO v2.0 HOST interfaces. Bluetooth Key Feature BT host digital interface:

- HCI UART (up to 4 Mbps)

- PCM for audio data Complies with Bluetooth Core Specification Version 5.0 with provisions for supporting future specifications. With Bluetooth Class 1 or Class2 transmitter operation. Supports extended synchronous connections (eSCO), for enhanced voice quality by allowing for retransmission of dropped packets. Adaptive frequency hopping (AFH) for reducing radio frequency interference. A simplified block diagram of the module is depicted in the figure above. Wi-Fi RF Specification 2.4GHz RF Specification Frequency Range:

802.11b/g/n-HT20/ax-HE20: 2412 ~ 2462MHz Channel Number:

802.11b/g/n-HT20/ax-HE20: 11 Type of Modulation:

802.11b: DSSS 802.11g/n: OFDM 802.11ax: OFDMA 5GHz RF Specification Frequency Range:

For 802.11a/n-HT20/ac-VHT20/ax-HE20:

5180~5240MHz, 5260~5320MHz, 5500~5720MHz, 5745~5825MHz For 802.11n-HT40/ac-VHT40/ax-HE40:

5190~5230MHz, 5270~5310MHz, 5510~5710MHz, 5755~5795MHz For 802.11ac-VHT80/ax-HE80:

5210MHz, 5290MHz, 5530MHz, 5610MHz, 5690MHz, 5775MHz Type of Modulation: 802.11a/n/ac: OFDM 802.11ax: OFDMA Note: The frequencies that fall in the 5600MHz to 5650MHz band will not be used in Canada. Bluetooth RF Specification Operating Frequency: 2402~2480MHz Channel Number:

BR/EDR: 79 BLE: 40 Type of modulation: GFSK, Pi/4 DQPSK, 8DPSK External clock reference U.S. FCC Statement FCC ID: H8N-AP6275S the following two conditions:

This device complies with Part 15 of the FCC Rules. Operation is subject to

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

o Reorient or relocate the receiving antenna. o Increase the separation between the equipment and receiver. o Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. o Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Canada (IC) Notices IC: 1353A-AP6275S CAN ICES-003(B) / NMB-003(B) This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions 1. lappareil ne doit pas produire de brouillage 2. lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. suivantes:

Caution:

Avertissement:

Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les memes canaux. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. OEM Integration Instructions Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4. For FCC Part 15.31 (h) and (k): The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting, and the evaluation should confirm that the module's intentional emissions are compliant (i.e. fundamental and out of band emissions). The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s). The Grantee will provide guidance to the host manufacturer for Part 15 B requirements if needed. IMPORTANT NOTE application. End Product Labeling Notice that any deviation(s) from the defined parameters of the antenna, as described by the instructions, require that the host product manufacturer must notify to Askey that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the USI, or the host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change When the module is installed in the host device, the FCC/IC label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: Contains Transmitter Module FCC ID: H8N-AP6275S or Contains FCC ID: H8N-AP6275S. The FCC ID/IC Certification Number can be used only when all FCC/IC compliance requirements are met. Antenna users.

(1) The antenna must be installed such that 20 cm is maintained between the antenna and

(2) The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/IC authorization is no longer considered valid, and the FCC ID/IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate FCC/IC authorization. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, maximum antenna gain (including cable loss) must not exceed. Antenna Specification:

Antenna Type Frequency Band TX Per Chain Max Antenna CDD Directional Gain

(GHz) Paths Gain (dBi)

(dBi) Ant 0 Ant 1 For Power For PSD 2.1 4.2 3.8 3.8 3.4 1.9 1.9 3.0 2.9 2.3 2.1 4.2 3.8 3.8 3.4 5.11 7.21 6.81 6.81 6.41 PIFA 2402 ~ 2480 1.9

Wi-Fi Internal Antenna PIFA 5260 ~ 5320 2412 ~ 2462 5180 ~ 5240 5500 ~ 5720 5745 ~ 5825 Bluetooth Internal Antenna 2 2 2 2 2 1 Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. List of applicable FCC rules Approval. This module has been tested and found to comply with part 15 requirements for Modular The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. 1. List of applicable FCC rules. KDB 996369 D03, Section 2.2 Complies with FCC Part 15.247 & Part 15.407. 2. Summarize the specific operational use conditions. KDB 996369 D03, Section 2.3 Refer to Antenna specification. 3. Limited Module Procedures. KDB 996369 D03, Section 2.4 This module is approved as single module. 4. Trace antenna designs. KDB 996369 D03, Section 2.5 Refer to Antenna specification. 5. RF exposure considerations. KDB 996369 D03, Section 2.6 The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 6. Antennas. KDB 996369 D03, Section 2.7 Refer to Antenna specification. 7. Label and compliance information. KDB 996369 D03, Section 2.8 Refer label file. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Industry Canada Statement This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement."

Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:

In the event that these conditions cannot be met (for example certain laptop configurations or colocation with another transmitter), then the Canada authorization is no longer considered valid, and the IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:

Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: 1353A-AP6275S. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: " Contains IC: 1353A-AP6275S ". Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. manual. The end user manual shall include all required regulatory information/warning as show in this Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Dimensions Label Recommended Reflow Profile Package Information

Askey Computer Corporation 10F, No. 119, Jiankang Rd., Zhonghe Dist., New Taipei City, Taiwan Attestation Letter Federal Communications Commission Authorization and Evaluation Division We Name: ASKEY COMPUTER CORPORATION Address: 10F, No.119, JIANKANG RD., ZHONGHE DIST., NEW TAIPEI CITY 23585, TAIWAN Declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. WIFI+BT Combo Module H8N-AP6275S AP6275S Product:

FCC ID:

Model:

Sincerely, _________________ Name: John Chiou Position: Manager Date: 2021-07-01

Askey Computer Corporation 10F, No. 119, Jiankang Rd., Zhonghe Dist., New Taipei City, Taiwan Confidentiality Request Letter Federal Communications Commission Authorization and Evaluation Division FCC ID: H8N-AP6275S Confidentiality Request 1. Block Diagram 2. Schematics 3. Operational Description application. Sincerely, _________________ Name: John Chiou Position: Manager Date: 2021-07-01 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this

Askey Computer Corporation 10F, No. 119, Jiankang Rd., Zhonghe Dist., New Taipei City, Taiwan Declaration of Authorization We Name: ASKEY COMPUTER CORPORATION Address: 10F, No.119, JIANKANG RD., ZHONGHE DIST., NEW TAIPEI CITY 23585, TAIWAN. Declare that:

Name Representative of agent: Marlin Chen Agent Company name:

Address:

MRT Technology (Suzhou) Co., Ltd D8 Building, Youxin Industrial Park, No.2 Tian'edang Rd., Wuzhong Economic Development Zone Suzhou China is authorized to apply for Certification of the following product(s):

WIFI+BT Combo Module H8N-AP6275S AP6275S City:

Country:

Product:

FCC ID:

Model:

Sincerely, _________________ Name: John Chiou Position: Manager Date: 2021-07-01

Askey Computer Corporation 10F, No. 119, Jiankang Rd., Zhonghe Dist., New Taipei City, Taiwan Request for Modular/Limited Modular Approval Date: July 1, 2021 Subject: Manufacturers Declaration for - Modular Approval Confidentiality Request for: _H8N-AP6275S

- Limited Modular Approval - Limited Split Modular Approval

- Split Modular Approval 8 Basic Requirements FCC Part 15.212(a)(1) For Items Marked NO(*), the Limited Module Description Must be Filled Out on the Following Pages Modular Approval Requirement Requirement Met 1. The modular transmitter must have its own RF shielding. This is intended to ensure that the module does not have to rely upon the shielding provided by the device into which it is installed in order for all modular transmitter emissions to comply with FCC limits. It is also intended to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed. Such coupling may result in non-compliant operation. The physical crystal and tuning capacitors may be located external to the shielded radio elements. 15.212(a)(1)(i) The radio portion of this module has been shielded, please see exhibition External Photo.

- YES - NO(*) 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with FCC requirements under conditions of excessive data rates or over-modulation. 15.212(a)(1)(ii) Data to the modulation circuit is buffered as described in the operational description provided with the application.

- YES - NO(*) 3. The modular transmitter must have its own power supply regulation on the module. This is intended to ensure that the module will comply with FCC requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. 15.212(a)(1)(iii) The module contains its own power supply regulation. Please refer to schematic filed with this application.

- YES - NO(*) 4. The modular transmitter must comply with the antenna and transmission system requirements of 15.203, 15.204(b), 15.204(c), 15.212(a), and 2.929(b). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph 15.212(b). 15.212(a)(1)(iv) The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report.

- YES - NO(*) 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(i)). 15.212(a)(1)(v) The EUT was tested in a stand-alone configuration via a test tool. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender.

- YES - NO(*) 070920-02b Askey Computer Corporation 10F, No. 119, Jiankang Rd., Zhonghe Dist., New Taipei City, Taiwan Modular Approval Requirement 6. The modular transmitter must be labeled with its own FCC ID number, or use an electron display (see Requirement Met KDB Publication 784748). If using a permanently affixed label with its own FCC ID number, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID:

XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. 15.212(a)(1)(vi) There is a label on the module as shown in the labeling exhibit filed with this application. Host specific labeling instructions are shown in the installation manual .filed with this application.

- YES - NO(*) 7. The modular transmitter must comply with all specific rule or operating requirements applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 15.212(a)(1)(vii) The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the User Manual.

- YES - NO(*) 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. 15.212(a)(1)(viii) The module meets Portable exclusion levels as shown in the RF exposure information filed with this application.

- YES - NO(*) Sincerely, _________________ Name: John Chiou Position: Manager Date: 2021-07-01 070920-02b

Askey Computer Corporation 10F, No. 119, Jiankang Rd., Zhonghe Dist., New Taipei City, Taiwan Confidentiality Request Letter Federal Communications Commission Authorization and Evaluation Division FCC ID: H8N-AP6275S Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request short-term confidential treatment for the following information until 180 days after the grant date of equipment authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

Attachments:

1. External Photo 2. Internal Photo 3. Test Setup Photo 4. User Manual Sincerely, _________________ Name: John Chiou Position: Manager Date: 2021-07-01