Quick installation guideline Signature lock with housing BLE FCC (Federal Communications Commission) statements This device comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) The BLE Module may not cause harmful interference, and 2) The BLE Module must accept any interference received, including interference that may cause undesired operation. Important note: To maintain compliance with FCCs RF exposure guidelines, this equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Use only the supplied antenna. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must n ot be co-located or operating in conjunction with any other antennas or transmitters. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. The concerned end product must be labeled to say Contains FCC ID: Y7V-7001CC1. IC (Industry Canada) statements This device comply with Industry Canada licence-exempt RSS standard CAN ICES-3 (B)/NMB-3(B) B. Operation is subject to the following two conditions:
1) The BLE Module may not cause interference, and 2) The BLE Module must accept any interference, including interference that may cause undesired operation of the device. Important note: To comply with Industry Canada RF radiation exposure limits for general population, the antennas used for these transmitters are exempted from Routine Evaluation Limits SAR Evaluation in accordance with RSS-102 section 2.5.1. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This BLE Module IC: 9514A-7001CC1 has been approved by Industry Canada to operate with the antenna type listed below with the indicated maximum permissible gain and required antenna impedance. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Name/Model Inverted F-antenna Gain 3.0 dBi Impedance 50 ohm The term "IC" before the equipment certification number only signifies that the Industry Canada technical specifications were met. The concerned end product must be labeled to say Contains IC: 9514A-7001CC1. Dclarations dIndustry Canada Cet quipement est conforme aux normes dexemption de licence RSS dIndustry Canada CAN ICES-3 (B)/NMB-3(B) B. Son utilisation est soumise aux deux conditions suivantes:
1) Le module BLE ne doit pas provoquer dinterfrence, et 2) Le module BLE doit accepter toute interfrence, y compris des interfrences susceptibles de provoquer un fonctionnement indsirable de lquipement. Remarque importante: Pour respecter les limites dexposition aux radiofrquences dIndustry Canada pour le grand public, les antennes utilises pour ces metteurs-transmetteurs sont exemptes des limites dvaluation de routine valuation SAR, conformment la norme RSS-102 section 2.5.1. Conformment aux rglementations dIndustry Canada, cet metteur radio peut uniquement fonctionner laide dune antenne dont le type et le gain maximal (ou minimal) pour ces metteurs-transmetteurs sont approuvs par Industry Canada. Pour rduire le risque d'interfrence ventuelle pour les autres utilisateurs, le type et le gain de l'antenne doivent tre choisis de manire ce que la puissance isotrope rayonne quivalente (p.i.r.e.) ne soit pas suprieure la puissance ncessaire une bonne communication. Ce module BLE IC: 9514A-7001CC1 a t approuv par Industry Canada pour une utilisation avec les types dantenne indiqus ci-dessous avec le gain maximum autoris indiqu et limpdance dantenne requise. Il est strictement interdit dutiliser avec cet appareil un type dantenne ne figurant pas dans cette liste ou ayant un gain suprieur au gain maximum indiqu pour ce type. Appellation/Modle Antenne F inverse Gain 3.0 dBi Impdance 50 ohm Le terme IC devant le numro de certification de lquipement signifie seulement que les spcifications techniques dIndustry Canada ont t respectes. Le produit final concern doit porter une tiquette avec la mention: Contient IC: 9514A-7001CC1. 66 1402 203-1 1 66 1402 203-5 Introduction With the Mobile Access option set in the Visionline software, the BLE technology (Bluetooth Low Energy) is used for exchanging data. Instead of using cards for access, mobile keys are used. The guest must have a Bluetooth telephone which is registered with an Endpoint ID, and an app for opening the door. A 3G RFID Signature lock is upgraded to BLE usage by following the steps in this instruction. Parts for the upgrade Figure 1: Signature kit, housing BLE Pos Description 1 2 3 4 5 Y-cable ZigBee&BLE for Classic Housing BLE Shield BLE Screw standoff Cable sleeve Quantity 1 1 1 2 1 Table 1: Contents of Signature kit, housing BLE Figure 2: BLE module Tools for the upgrade Screwdriver Torx TR20 USB interface 3G; complete ordering name Lock Service 3G; minimum version 1.1.1 is cable RJ12 to USB adapter (for 3G) Service cable; complete ordering name is service cable RJ12 for 3G RFID LCU
& E-cylinder The information in this document is subject to change at the sole discretion of ASSA ABLOY without notice. Any use, operation or repair in contravention of this document is at your own risk. ASSA ABLOY does not assume any responsibility for incidental or consequential damages arising from the use of this document. All information and drawings in this document are the property of ASSA ABLOY. Unauthorized use and reproduction is prohibited. VingCard and Elsafe are registered trademarks of ASSA ABLOY. For R&TTE statements for the BLE module, see Installation instruction Mobile access option. 66 1402 203-1 2 66 1402 203-5 Procedure Figure 4 Figure 4 1. If the door thickness requires it: exchange the regular spacers on the back of the LCU Signature RFID assy with the screws standoff (item number 4 in Figure 1). 2. Mount the LCU Signature RFID assy (3G) in the housing BLE. Figure 5 3. Thread the cable sleeve onto the 3G RFID LCU reader cable. Figure 7 Figure 6 4. Thread the Y-cable ZigBee&BLE for Classic (from now on called Y-cable) through the shield BLE and through the cable sleeve, which will now contain two cables (3G RFID LCU reader cable and Y-cable). Figure 8 Figure 9 5. Connect the Y-cable to the BLE module. Figure 10 Mount the BLE module in the housing BLE. 7. Push the cable sleeve all the way down 9. Thread the cable sleeve through the middle hole to the housing BLE. 8. Thread the shield BLE over the spacers (or screws standoff if applicable) and all the way down to the housing BLE. of the door cut-out and the spacers (or screws standoff if applicable) through the outer holes of the door cut-out. 6. 66 1402 203-1 3 66 1402 203-5 Figure 11 10. Mount the housing BLE including the LCU Signature RFID assy (3G) on the door; the spacers (or the screws standoff) on the back of the LCU Signature RFID assy (3G) are in step 11 fastened together with the mounting frame (full name mounting frame inside Signature). Figure 12 11. Use a screwdriver Torx TR20
(or Torx T20) to fasten the mounting frame with two screws on the back of the door. Note: Make sure to align the mounting frame on both sides before fastening it. Figure 15 Note: The plug parking on the left side of the battery protection cannot be used since the cables are too short. 12. Snap the LCA 6343 onto the mounting frame (hide the Figure 13 Figure 14 14. Snap the battery protection (marked with an arrow in Figure 15) lock motor cable and the 3G RFID LCU reader cable behind it). onto the mounting frame. 13. Connect the cables according to Figure 13. Use the tabs on the sides of the mounting plate to keep the cables in place; see Figure 14. I. Connect the ground cable to the connector at the mounting frame. II. Connect the lock motor cable to the 10-pin connector on the left side of the LCA 6343. 15. Connect the LCA part of the Y-cable to the 7-pin connector on the right side of the LCA 6343; marked I in Figure 15. 16. Load the battery holder 4.5V with 3 AA batteries. 17. Mount the battery holder 4.5V in the battery protection with the batteries standing as shown in Figure 15. 18. Connect the battery cable (full name: battery cable Signature/
19. Classic 4.5V/Classic 9V) to the 2-pin connector on the right side of the LCA 6343; marked II in Figure 15. 66 1402 203-1 4 66 1402 203-5 Figure 16 20. Use the tabs on the sides of the mounting plate to keep the cables in place; see Figure 16. 23. Use a service cable and Lock Service 3G Figure 18 to upload the BLE lock firmware, 3.47.XX. The firmware is included under the Upload firmware alternative in Lock Service 3G;
see Quick reference guide Lock Service 3G for details. If a later firmware version is available, first use the Download firmware alternative; see Quick reference guide Lock Service 3G for details. Figure 17 21. Thread the battery cover Signature onto the mounting frame. 22. Use a screwdriver Torx TR20 to fasten the battery cover Signature. ASSA ABLOY Hospitality APAC: e-mail apac.hospitality@assaabloy.com, phone +65 6305 7670 ASSA ABLOY Hospitality North America: e-mail northam.hospitality@assaabloy.com, phone +1 972 907 2273 ASSA ABLOY Hospitality EMEA: e-mail emea.hospitality@assaabloy.com, phone +47 69 24 50 00 ASSA ABLOY Hospitality Latin America: e-mail lam.hospitality@assaabloy.com, phone +52 55 36 40 12 00 66 1402 203-1 5 66 1402 203-5