Quick Reference Guide ZigBee Gateway ASSA ABLOY Hospitality 1 Copyrights The information in this document is subject to change at the sole discretion of ASSA ABLOY without notice. Any use, operation or repair in contravention of this document is at your own risk. ASSA ABLOY does not assume any responsibility for incidental or consequential damages arising from the use of this manual. All information and drawings in this document are the property of ASSA ABLOY. Unauthorized use and reproduction is prohibited. VingCard and Elsafe are registered trademarks of ASSA ABLOY. ASSA ABLOY Hospitality 2 Table of contents FCC and IC statements FCC statements IC statements
.................................................................................................4
............................................................................................................................ 4
............................................................................................................................ 5 Gateway dimensions
.................................................................................................6 Quick reference of technical data
.................................................................................................7 To mount a gateway
.................................................................................................8 ASSA ABLOY Hospitality 3 FCC and IC statements FCC (Federal Communications Commission) statements This device comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Important note: To maintain compliance with FCCs RF exposure guidelines, this equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Use only the supplied antenna. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antennas or transmitters. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. The concerned end product must be labeled to say 'FCC ID: Y7V-683081066C1'. The concerned end product must be labeled to say 'FCC ID: Y7V-GW683081066'. ASSA ABLOY Hospitality 4 66 3081 060-3 IC (Industry Canada) statements This device comply with Industry Canada licence-exempt RSS standard CAN ICES-3 (B)/NMB-3(B) B. Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conform aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Important note: To comply with Industry Canada RF radiation exposure limits for general population, the antennas used for these transmitters must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times and must not be co-located or operating in conjunction with any other antenna or transmitter. Under Industry Canada regulations, these radio transmitters may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitters by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication. These radio transmitters IC9514A-683081066C1 and IC9514A-683081066 have been approved by Industry Canada to operate with the antenna type listed below with the indicated maximum permissible gain and required antenna impedance. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Name/Model Inverted F-antenna Gain 3.0 dBi Impedance 50 ohm The term "IC" before the equipment certification number only signifies that the Industry Canada technical specifications were met. Le terme "IC" devant le numro de certification signifie seulement que les specifications techniques Industrie Canada ont t respectes. ASSA ABLOY Hospitality 5 66 3081 060-3 Gateway dimensions Figure 1 ASSA ABLOY Hospitality 6 66 3081 060-3 Quick reference of technical data Note: For more information about the gateway (e.g. about web interface, reset, boot-up, commissioning the gateway in a ZigBee system etc), see User manual Online option. Figure 2 Automatic adjustment to 10 or 100 Mbit/s networks Powered via Ethernet or by a power adapter (5VDC) Note: The gateway is of PoE class 1; power range 0.44-3.84W. Low power consumption The total number of gateways is virtually unlimited Can have either five routers or 15 endnodes connected Case with the dimensions 63,0 mm x 144,0 mm x 27,5 mm
(2 31/64" x 5 43/64" x 1 3/32") Easy mounting (can be mounted either with adhesive VELCRO strips or fastening screws; a package with two VELCRO strips and two fastenings screws are enclosed) Weight: 116 g Flame retardant ABS UL94 V-0 approved Colour: RAL 7047 Suitable for operation in the range 5-50 C and 10-90%
non-condensed relative humidity ASSA ABLOY Hospitality 7 66 3081 060-3 To mount a gateway Preferred way of mounting the gateway is horizontally:
Figure 3 ASSA ABLOY Hospitality 8 66 3081 060-3 ASSA ABLOY Hospitality APAC E-mail: apac.hospitality@assaabloy.com Phone: +65 6305 7670 ASSA ABLOY Hospitality EMEA E-mail: emea.hospitality@assaabloy.com Phone: +47 69 24 50 00 ASSA ABLOY Hospitality North America E-mail: northam.hospitality@assaabloy.com Phone: +1 972 907 2273 ASSA ABLOY Hospitality Latin America E-mail: lam.hospitality@assaabloy.com Phone: +52 55 36 40 12 00 www.assaabloyhospitality.com ASSA ABLOY Hospitality 9